Answer:
The short steep ramp would be much harder because you will have to work more against gravity.
Explanation:
The long shallow ramp would be easier to take than the short, steep ramp because the person would have to use more force on the short, steep ramp to push the wheelchair against the force of gravity.
What is an inclined plane?An inclined plane or a ramp can be defined as a flat supporting surface tilted at an angle, with one end higher than the other, utilized as an aid for raising or lowering a load.
The inclined plane can be defined as one of the six classical simple machines developed by Renaissance scientists. Inclined planes can be utilized to move heavy loads over vertical obstacles.
Moving a body up an inclined plane needs less force than lifting it straight up, at a cost of an increase in the distance moved. The mechanical advantage, the factor by which the force is decreased, is equal to the ratio of the sloped surface's length to the height it spans.
The inclined plane provides the same amount of work to be done with a smaller force exerted over a greater distance. The angle of friction or the angle of repose can be defined as the maximum angle at which a load can rest motionless on an inclined plane because of the friction without sliding down.
Learn more about Inclined plane, here:
https://brainly.com/question/14983337
#SPJ2
Which option is a mixture? a.carbon dioxide b. air c. oxygen d. carbon
Answer:
Air
Explanation:
Did test 100
Which noble gases is closest to magnesium? On the periodic table? What must happen if a magnesium atom for it to have an electron arrangement similar to that of a noble gas?
Answer:
Neon and loose electrons
Explanation:
Magnesium has an electron configuration of 2e 8e 2e, and Neon is 2e,8e. For Mg to have a similar electron arrangement it must loose its two valence electrons and make it an ion.
Answer:
Noble neon gas is the closest.
Explanation:
noble Neon gas
The Magnesium would have to lose two electrons
The hottest place in California is Death Valley with a record temperature of 130 ⁰F. Calculate the temperature in ⁰C and K.
Answer:
54.(4)° C (the 4 in the parentheses means the 4 goes forever), 327.594°K
Explanation:
When you convert 130°F to °C, you will get 54.(4)°C, and the 4 in the parentheses goes forever, and 130°F to °K is 327.594°K, hope it helps!
Which is a dominant trait that Mendel observed in pea plant
A. Bumpy pods
B. Short height
C. Yellow seeds
D. White flowers
it is not A
Answer:
C, yellow seeds
Explanation:
In Mandel's studies, he proved that yellow seeds were to be dominant and green seeds were to be recessive.
Answer:
c. yellow seeds
Explanation:
i toke the test
What happens to particles in a sample of liquid when the liquid is heated and cooled?
Calculate the entropy change when 4.31 g of H2 reacts with O2 according to the reaction
2 H2(g) + O2(g) → 2 H2O(l)
at 298 K and 1 atm pressure. The standard molar enthalpy of formation of H2O(l) at 298 K is −285.8 kJ/mol. The corresponding free energy of formation is −237.2 kJ/mol.
Answer in units of J/K.
Answer:
Explanation:
ΔG = Δ H - T ΔS
Given , ΔG = -237.2 kJ / mol
Δ H = - 285.8 kJ / mol
T = 298
Putting the values in the equation
-237.2 = - 285.8 - 298 x ΔS
ΔS = .163 kJ / mole K
moles of water formed = 4.31 / 2 = 2.155
entropy change required = 2.155 x .163 kJ / K
= 351.26 J / K .
Explain the term catalyst and how it affects the rate of a chemical reaction.
Answer:
Catalyst. A catalyst speeds up a chemical reaction, without being consumed by the reaction. It increases the reaction rate by lowering the activation energy for a reaction. Energy diagrams are useful to illustrate the effect of a catalyst on reaction rates.
Explanation:
a sample of alcohol has a density 0.82 g/ml.what is the mass of 5500 mL of the alcohol
Answer:
The answer is 4510 gExplanation:
The mass of a substance when given the density and volume can be found by using the formula
mass = Density × volumeFrom the question
density = 0.82 g/mL
volume = 5500 mL
We have
mass = 0.82 × 5500
We have the final answer as
4510 gHope this helps you
Which changes involve forming or breaking chemical bonds?
A.burning and digesting
B.boiling and melting
C.burning and melting
D.rusting and cutting
Answer:
d
Explanation:
i took the test
What type of reaction is the equation 2NaCl → 2Na +Cl2?
Answer:
Synthesis reaction
Explanation:
This is a synthesis reaction. When you combine sodium metal (Na) with chlorine gas (Cl), you form sodium chloride or kosher salt (NaCl).
Hope this explanation helps!
Calculate number of moles in 42g of silicon.
Answer:
[tex]\frac{3}{2}[/tex]
Explanation:
No of moles : [tex]\frac{given mass}{atomic mass}[/tex]
so the given mass is 42 gm and atomic mass of silicon is 24 when u solve it u get 3/2
The most important ELEMENT found in all living things is
A. Oxygen
B. hydrogen
C. Nitrogen
D. Carbon
Answer:
A. Carbon hope this helps
Answer:
D. Carbon. I guess that's the answer
Which contribution is a modification to Thomson's plum pudding model?
Atoms are indivisible.
Electrons are scattered in an atom.
A positively charged nucleus sits at the center of an atom.
Atoms of the same element have the same properties.
Answer:
Option C: A positively charged nucleus sits at the center of an atom.
Explanation:
Thompson’s plum pudding model was a model proposed by Thompson to show that an atom consisted of more than one fundamental unit.
In Thompson's model, he suggested that the atom consisted of a cloud of positive charges which were surrounded by electrons which are negative charges distributed throughout.
Now, Thompson's experiment was later rejected by Ernest Rutherford when he carried out the gold foil experiment and came to the conclusion where he proposed a model that the atom consisted of mainly empty space and that all its positive charge are concentrated at its center and further surrounded by a cloud of electrons.
From the given options, the correct one is Option C.
Answer: Option C: A positively charged nucleus sits at the center of an atom.
Explanation:
Explain the term rate of a chemical reaction.
Answer:
The rate of a reaction is a measure of how quickly a reactant is used up, or a product is formed.
Explanation:
40POINTS AND BRAINLIEST Discuss the orders in which electrons are filled in the s and d subshells of the first three elements in group11
Step 1: add electrons to fill the 1s subshell (maximum of 2 electrons), when this is full, go to step 2. Step 2: add electrons to fill the 2s subshell (maximum of 2 electrons), when this is full, go to step 3. Step 3: add electrons to fill the 2p subshell (maximum of 6 electrons), when this is full, go to step 4. Step 4: add electrons to fill the 3s subshell (maximum of 2 electrons), when this is full, go to step 5. Step 5: add electrons to fill the 3p subshell (maximum of 6 electrons), when this is full, go to step 6. Step 6: add electrons to the 4s subshell (maximum of 2 electrons), when this is full, go to step 7. Step 7: add electrons to the 3d subshell (maximum of 10 electrons), when this is full, go to step 8. Step 8: add electrons to the 4p subshell (maximum of 6 electrons), when this is full, go to step 9. etc
So for Cu would be: 1s^22s^22p^63s^23p^63d^9
Ag would be: 1s^22s^22p^63s^23p^63d^104s^24p^64d^105s^1
Au would be: 1s^22s^22p^63s^23p^63d^104s^24p^64d^105s^25p^64f^145d^106s^1
A horse traveled a distance of 20 miles in 2
hours. What was the horse's speed?
Answer:
The horses speed was 10 miles per hour.
Explanation:
20/2=10
Hope this helps!
Formula for all possible isomers of hexane
Answer:
1) n-Hexane. 2) 2-Methyl pentane(IUPAC name) or Isohexane(common name). 3) 2,2-Dimethylbutane(IUPAC name) or Neohexane(common name). 4) 3-Methylpentane
Explanation:
Which one of the following is the symbol used in a chemical equation for a
gas?
A. (g)
B. (aq)
C. (gas)
D. (a)
Answer:
A. (g)
Explanation:
Since it asks for a gas, it is A.
Answer:
A (g)
Explanation:
Which action would cause the chair to move to the left?
A. Applying 100 N of force to the chair from the left
B. Applying 100 N of force to the chair from the right
C. Applying 200 N of force to the chair from the right
D. Applying 200 N of force to the chair from the left
SUBMIT
PREVIOUS
5. What is a hypothesis and how is it used?
Answer: a supposition or proposed explanation made on the basis of limited evidence as a starting point for further investigation.
A hypothesis is used in an experiment to define the relationship between two variables. The purpose of a hypothesis is to find the answer to a question. A formalized hypothesis will force us to think about what results we should look for in an experiment. The first variable is called the independent variable
i hopes this helps :)
You come across a mysterious substance that has a mass of 1.8225 x 10 to the power of 2g
and a volume of 0.025 L (1L = 1000 mL). Using the density formula what is the density
Answer:
192
Explanation:
Bc its 182
how many molecules are in CO²
Answer:
53.11× 10²³ molecules
Explanation:
Given data:
Number of molecules of CO₂ = ?
Mass of CO₂ = 388.1 g
Solution:
Formula:
Number of moles = mass/ molar mass
Molar mass of CO₂ = 12× 1 + 16×2
Molar mass of CO₂ = 44 g/mol
Now we will put the values in formula.
Number of moles = 388.1 g/ 44 g/mol
Number of moles = 8.82 moles
Now we will calculate the number of molecules by using Avogadro number.
It is the number of atoms , ions and molecules in one gram atom of element, one gram molecules of compound and one gram ions of a substance.
The number 6.022 × 10²³ is called Avogadro number.
1 mole = 6.022 × 10²³ molecules
8.82 mol × 6.022 × 10²³ molecules / 1 mol
53.11× 10²³ molecules
Brainliest plz?
Answer:
Now times by Abogadros constant: 1* 6.022*10^23=6.022*10^23 molecules of CO2 are present.
Explanation:
We know the molar mass of CO2(g) is 44.01⋅g⋅mol−1 . And so Avogadro's number of carbon dioxide molecules have this mass... And we take the product of the quotient... Molecules of carbon dioxide=5.00⋅mol×6.022×1023⋅mol−1≅30×1023⋅carbon dioxide molecules.
The unknown element (Johnsonium, Jo) contains three naturally occurring isotopes. The relative abundances and atomic mass are:
Moorium-36: abundance = 1.32%, mass = 35.978amu
Moorium-38: abundance = 3.25%, mass = 37.963amu
Moorium-40: abundance = 95.43%, mass = 39.962amu
What is the average atomic mass of "Moorium?"
Answer:
Average atomic mass of moorium is 39.844 amu.
Explanation:
Given data:
Atomic mass of moorium-36 = 35.978 amu
Relative abundance of moorium-36 = 1.32%
Atomic mass of moorium-38 = 37.963 amu
Relative abundance of moorium-38 = 3.25%
Atomic mass of moorium-40 = 39.962 amu
Relative abundance of moorium-38 = 95.43%
Solution:
Average atomic mass moorium = (abundance of 1st isotope × its atomic mass) +(abundance of 2nd isotope × its atomic mass)+ (abundance of 3rd isotope × its atomic mass) / 100
Average atomic mass of moorium = (1.32×35.978)+(3.25×37.963)+(95.43×39.962) /100
Average atomic mass of moorium = 47.491 + 123.380 +3813.574 / 100
Average atomic mass of moorium = 3984.445 / 100
Average atomic mass of moorium = 39.844 amu
An unknown metal has a density of 10.51 g/ml and a mass of 287.8 g. What is the
unknown metal's volume?
Answer:
27.3834443387 so B
Explanation:
M/D=V
287.8/10.51=V
V=27.3834443387
Answer:
27.38
Explanation:
287.8 Divided by 10.51 = 27.38
Please mark brainliest if helped
Please help I’ll give brainiest!
Answer:
Im sorry if u get it worng but is it the 3rd one?
Explanation:
Helium gas (He) is an element and not a compound. Why is this true?
Where in equation for photosynthesis does carbon dioxide belong
Answer:
The equation for photosynthesis is 6 CO2 + 6 H2O + light --> C6H12O6 + 6 O2, so carbon dioxide will be found in the reactant part of the equation.
NEED HELP FAST!!!!
Points A and B are locations on the banks of a river. What are the dominant processes occurring at locations A and B? *
A. deposition at location A; erosion at location B
B. erosion at location A; deposition at location B
C. deposition at both locations A and B
D. Erosion at both locations A and B
Answer:
C
Explanation:
During a change in state, energy is transferred in the form of
heat
light
moisture
motion
Answer:
heat I think.....
Hope it will help you......During a change in state, energy is transferred in the form of heat.
Hence, Option (A) is correct.
What is States of matter ?
When energy is added or removed to matter in the form of heat, it changes state to form a state of matter.
A state of matter is defined as one of the ways in which matter can interact with itself to form a homogeneous phase.
Therefore , During a change in state, energy is transferred in the form
of heat. Hence, Option (A) is correct.
Learn more about States of matter here ;
https://brainly.com/question/9402776
#SPJ2
How has cooperation played a role in life's major evolutionary transitions?
Answer:
The cooperation of a species is shown throughout history. Including in our history. Where it be physical evolution or technological. We have helped each other with building, advice, locations, Reproduction, etc.