To remove the contract type "time and materials" from the contracttypes table, you can use a SQL query with the DELETE statement. Here's a brief explanation of the steps involved:
1. The DELETE statement is used to remove specific rows from a table based on specified conditions.
2. In this case, you want to remove the contract type "time and materials" from the contracttypes table.
3. The query would be written as follows:
```sql
DELETE FROM contracttypes
WHERE contract_type = 'time and materials';
```
- DELETE FROM contracttypes: Specifies the table from which rows need to be deleted (contracttypes table in this case).
- WHERE contract_type = 'time and materials': Specifies the condition that the contract_type column should have the value 'time and materials' for the rows to be deleted.
4. When you execute this query, it will remove all rows from the contracttypes table that have the contract type "time and materials".
It's important to note that executing this query will permanently delete the specified rows from the table, so it's recommended to double-check and backup your data before performing such operations.
Learn more about query:
https://brainly.com/question/25266787
#SPJ11
Which of the followings is true? Given an RC circuit: resistor-capacitor C in series. The output voltage is measured across C, an input voltage supplies power to this circuit. For the transfer function of the RC circuit with respect to input voltage: O A. Its phase response is -90 degrees. O B. Its phase response is negative. O C. Its phase response is 90 degrees. O D. Its phase response is positive.
In an RC circuit with a resistor-capacitor in series and the output voltage measured across C while an input voltage supplies power to this circuit, the phase response of the transfer function of the RC circuit with respect to input voltage is -90 degrees.
Hence, the correct answer is option A. A transfer function is a mathematical representation of a system that maps input signals to output signals.The transfer function of an RC circuit refers to the voltage across the capacitor with respect to the input voltage. The transfer function represents the system's response to the input signals.
The transfer function H(s) of the RC circuit with respect to input voltage V(s) is given by the equation where R is the resistance, C is the capacitance, and s is the Laplace operator. In the frequency domain, the transfer function H(jω) is obtained by substituting s = jω where j is the imaginary number and ω is the angular frequency.A phase response refers to the behavior of a system with respect to the input signal's phase angle. The phase response of the transfer function H(jω) for an RC circuit is given by the expression.
To know more about resistor-capacitor visit :
https://brainly.com/question/31080064
#SPJ11
Prove that a Schmitt oscillator trigger can work as a VCO.
Step 1:
A Schmitt oscillator trigger can work as a VCO (Voltage Controlled Oscillator).
Step 2:
A Schmitt oscillator trigger, also known as a Schmitt trigger, is a circuit that converts an input signal with varying voltage levels into a digital output with well-defined high and low voltage levels. It is commonly used for signal conditioning and noise filtering purposes. On the other hand, a Voltage Controlled Oscillator (VCO) is a circuit that generates an output signal with a frequency that is directly proportional to the input voltage applied to it.
By incorporating a voltage control mechanism into the Schmitt trigger circuit, it can be transformed into a VCO. This can be achieved by introducing a variable voltage input to the reference voltage level of the Schmitt trigger. As the input voltage changes, it will cause the switching thresholds of the Schmitt trigger to vary, resulting in a change in the output frequency.
The VCO functionality of the modified Schmitt trigger circuit allows it to generate a continuous output signal with a frequency that can be controlled by the applied voltage. This makes it suitable for various applications such as frequency modulation, clock generation, and signal synthesis.
Step 3:
Learn more about : frequency
Describe frequency, relative frequency, and cumulative relative frequency.
#SPJ11
QUESTION 1 Which of the followings is true? Narrowband FM is considered to be identical to AM except O A. their bandwidth. O B. a finite and likely large phase deviation. O C. an infinite phase deviation. O D. a finite and likely small phase deviation.
Narrowband FM is considered to be identical to AM except in their bandwidth. In narrowband FM, a finite and likely small phase deviation is present. It is the modulation method in which the frequency of the carrier wave is varied slightly to transmit the information signal.
Narrowband FM is an FM transmission method with a smaller bandwidth than wideband FM, which is a more common approach. Narrowband FM is quite similar to AM, but the key difference lies in the modulation of the carrier wave's amplitude in AM and the modulation of the carrier wave's frequency in Narrowband FM.
The carrier signal in Narrowband FM is modulated by a small frequency deviation, which is inversely proportional to the carrier frequency and directly proportional to the modulation frequency. Therefore, Narrowband FM is identical to AM in every respect except the bandwidth of the modulating signal.
When the modulating signal is a simple sine wave, the carrier wave frequency deviates up and down about its unmodulated frequency. The deviation of the frequency is proportional to the amplitude of the modulating signal, which produces sidebands whose frequency is equal to the carrier frequency plus or minus the modulating signal frequency.
To know more about modulation visit:
https://brainly.com/question/28520208
#SPJ11
please need answer asap
5 5. An aircraft is moving steadily in the air at a velocity of 330 m/s. Determine the speed of sound and Mach number at (a) 300 K (4 marks) (b) 800 K. (4 marks)
The speed of sound can be calculated using the equation v = √(γRT), where v is the speed of sound, γ is the adiabatic index (1.4 for air), R is the gas constant (approximately 287 J/kg*K), and T is the temperature in Kelvin.
(a) At 300 K, the speed of sound can be calculated as v = √(1.4 * 287 * 300) = 346.6 m/s. To find the Mach number, we divide the velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/346.6 ≈ 0.951.
(b) At 800 K, the speed of sound can be calculated as v = √(1.4 * 287 * 800) = 464.7 m/s. The Mach number is obtained by dividing the velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/464.7 ≈ 0.709.
The speed of sound can be calculated using the equation v = √(γRT), where v is the speed of sound, γ is the adiabatic index (1.4 for air), R is the gas constant (approximately 287 J/kg*K), and T is the temperature in Kelvin. For part (a), at a temperature of 300 K, substituting the values into the equation gives v = √(1.4 * 287 * 300) = 346.6 m/s. To find the Mach number, which represents the ratio of the aircraft's velocity to the speed of sound, we divide the given velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/346.6 ≈ 0.951. For part (b), at a temperature of 800 K, substituting the values into the equation gives v = √(1.4 * 287 * 800) = 464.7 m/s. The Mach number is obtained by dividing the given velocity of the aircraft (330 m/s) by the speed of sound: Mach number = 330/464.7 ≈ 0.709.
Learn more about Mach number here
brainly.com/question/29538118
#SPJ11