Answer:
E = 3456 J
Explanation:
The electrical energy expended in a resistor can be easily calculated by using the following formula:
[tex]E = Pt[/tex]
where,
E = Energy Expended = ?
I = current through 5 ohm resistor = 2.4 A
R = Resistance = 5 ohms
P = Electrical Power = VI
Since,
V = IR (Ohm's Law)
Therefore,
P = (IR)(I) = I²R = (2.4 A)²(5 ohms) = 28.8 Watt
t = time taken = (2 min)(60 s/1 min) = 120 s
Therefore,
E = (28.8 Watt)(120 s)
E = 3456 J
Two long straight parallel lines, #1 and #2, carry uniform positive linear charge densities. The charge density on line #2 is twice as great as the charge density on line #1. The locus of points where the electric field due to these lines is zero is
along a line between the lines closer to line #2 than line #1.
at a point midway between the lines.
along a line between the lines closer to line #1 than line #2.
along a line perpendicular to lines #1 and #2.
Answer:
The locus of points where the electric field due to these lines is zero is;
Along the line between the lines closer to line#1 than line #2
Explanation:
The charges on the parallel lines #1 and #2 = Positive linear charge
The charge density on line #2, λ₂ = 2 × The charge density on line #1, λ₁
Therefore, we have;
λ₂ = 2 × λ₁
Electric field strength, E, is given as follows;
[tex]E = \dfrac{\lambda}{2\cdot \pi\cdot \epsilon_0\cdot d}[/tex]
Therefore;
[tex]E_1 = \dfrac{\lambda_1}{2\cdot \pi\cdot \epsilon_0\cdot d}[/tex]
[tex]E_2 = \dfrac{\lambda_2}{2\cdot \pi\cdot \epsilon_0\cdot d} = 2 \times\dfrac{\lambda_1}{2\cdot \pi\cdot \epsilon_0\cdot d}[/tex]
E₂ = 2·E₁
E₂/2 = E₁
E₂/(2·d) = E₁/d
The strength of the electric field at a given distance from line #2 is 2 times the strength of the electric field from line #1 at the same distance
Therefore the strength of the electric field will be the same at a point twice the distance from line #2 than from line #1 which is a point closer to line #1 than line #2.
Un puente(construido de acero) que conduce hacia una bahía mide 1.30X10-3m entre sus torres de apoyo. ¿Cuánto se dilata el puente durante un día en el que la temperatura alcanza una diferencia de 30°C?
Answer:
ΔL = 0.429 m
Explanation:
The expression for linear thermal expansion is
ΔL = α L₀ ΔT
the coefficient of linear expansion of steel is 11 10⁻⁶ ºC⁻¹
the initial length of the bridge is L₀ = 1.30 10³ m and the temperature variation is ΔT = 30 ºC
calculate
ΔL = 11 10⁻⁶ 1.30 10³ 30
ΔL = 4.29 10⁻¹ m
ΔL = 0.429 m
Hey, can someone solve this for me? tysm
Answer:
The Answer is gonna be B. The normal force (magnitude and direction)
Answer:
solution given ;
mass[m]=55kg
acceleration due to gravity [g]=10m/s²
weight[W]=mg=55×10=550 Newton
How strong is the electric field between two parallel plates 5.8 mm apart if the potential difference between them is 200 V?
Answer: Electric field is given as
E = V/d
E = 220 v / 0.0056m
E = 39285.71 v/m
Or
E = 39285.71 N/C
Explanation: Therefore electric field is 39285.71 V/m
Answer:
Answer: Electric field is given as
E = V/d
E = 220 v / 0.0058m
E = 37931.03 v/m
Or
E = 37931.03 N/C
Explanation:
e=v/d
Which statement is false?
A) Doubling the mass halves the acceleration
B) Doubling the force doubles to acceleration
C) Doubling the mass doubles the acceleration
Statement C is false. Doubling the mass doubles the acceleration is the wrong statement.
What is force?Force is defined as the push or pulls applied to the body. Sometimes it is used to change the shape, size, and direction of the body.
Force is defined as the product of mass and acceleration. Its unit is Newton.
Mathematically, the force is;
[tex]\rm F= ma[/tex]
If force is constant, the mass is inversely proportional to the acceleration. If the mass is double in that condition, acceleration is halved.
Doubling the mass doubles the acceleration is the wrong statement.
Hence, statement C is false
To learn more about the force, refer to the link;
https://brainly.com/question/26115859
#SPJ2
Which applications, either for diagnostic purposes or for therapeutic purposes, involve the use of X-rays? Check all that apply.
CT scan
MRI
radiography
brachytherapy
laser eye surgery
radioisotope imaging
external beam radiation therapy
fluoroscopy
Answer:
1,3,7,8
Explanation:
Edge 2021
what will happen if you increse the amplitude of a drum hit
The sound is perceived as louder if the amplitude increases, and softer if the amplitude decreases. As the amplitude of the sound wave increases, the intensity of the sound increases. Sounds with higher intensities are perceived to be louder.
Which of these chemical formulas is balanced?
The balanced formula is B.
can any one give me a good egg drop design that is over 500 grams?
Answer:
Hightail ur butt to walmart and get a squash, cut off the top and scoop out a hole the size of the egg, put the egg in but make sure there's as little space as it can be so the egg wont move around in it, then put the top of the squash back on and cover it in duct tape to keep the top from flying off.
Explanation:
A 75N horizontal force is sufficient to move a 150N box on a level road at a uniform speed. What is the coefficient of friction between the box and the road?
Answer:
[tex]\mu_k=0.5[/tex]
Explanation:
From the question we are told that:
Force [tex]F=75N[/tex]
Weight [tex]W=150N[/tex]
Generally the equation for coefficient of friction [tex]\mu_k[/tex] is mathematically given by
[tex]\mu_k=\frac{F}{mg}[/tex]
[tex]\mu_k=\frac{75}{150}[/tex]
[tex]\mu_k=0.5[/tex]
Cart 1 of mass 3.0 kg moving to the right at 2 m/s and collides with a Cart 2 of mass 2.0 kg moving to the left at
4 m/s. The two carts stick together. What is the velocity of the carts after the collision?
Answer:
V = -0.4 m/s
Explanation:
Given that,
Mass of cart 1, m₁ = 3 kg
Speed of cart 1, v₁ = 2 m/s
Mass of cart 2, m₂ = 2 kg
Speed of cart 2, v₂ = -4 m/s (left)
aWe need to find the velocity of the carts after the collision if they stick together. Let the common speed be V. Using the law of conservation of momentum to find it such that,
[tex]m_1v_1+m_2v_2=(m_1+m_2)V\\\\V=\dfrac{m_1v_1+m_2v_2}{(m_1+m_2)}[/tex]
Put all the values,
[tex]V=\dfrac{3\times 2+2\times (-4)}{(3+2)}\\\\=-0.4\ m/s[/tex]
So, the velocity of the carts after the collision is equal to 0.4 m/s to the left.
in an exothermic reaction, chemical energy is converted to ____ energy.
FILL IN THE BLANK.
MECHANICAL OR THERMAL.
Answer:thermal energy
Explanation:
please mark this answer as brainliest
Which is true about forensic testing? Forensic scientists must accurately interpret test results Evidence testing is no longer reliable All tests are fully automated Forensic scientists never make mistakes
Answer:
Forensic scientists must accurately interpret test results
Explanation:
Misinterpreting test results could mean someone being falsely accused of a crime which you would want to avoid.
How do we use pulleys in real life?
Answer:
Construction pulleys are used in order to lift and place heavy materials. Curtains at a theatre are moved using pulley systems that pull the curtains apart. Blinds on windows operate using a pulley system to move the blinds up and down.
We use pulleys for things like and elevators, cranes, and bikes.
Kyle is playing volleyball. After he hits the ball, it reaches its maximum height and then falls toward the ground due to the force of gravity.
Which statement best describes the interaction between the ball and Earth?
The ball and Earth attract each other with equal magnitudes of gravitational force.
O
The ball and Earth produce equal magnitudes of gravitational acceleration on each other.
The gravitational force exerted by the ball is much less than the gravitational force exerted by Earth.
Earth exerts a gravitational force on the ball, but the ball is too small to exert a gravitational force on Earth.
A force of 70 N is applied to a 28 kg rock causing it to slow down from 25 m/s to 15 m/s, a change in velocity of 10 m/s. How long was that force applied?
Answer: 4 s
Explanation:
Given
The applied force is 70 N
mass of the rock is 28 kg
initial velocity [tex]u=25\ m/s[/tex]
final velocity [tex]v=15\ m/s[/tex]
Deceleration provided by force is
[tex]a=-\dfrac{70}{28}=-2.5\ m/s^2[/tex]
using the equation of motion
[tex]v=u+at\\\Rightarrow 15=25-2.5t\\\Rightarrow 2.5t=10\\\Rightarrow t=4\ s[/tex]
What device increases voltage?
A. generator
B. motor
C. step-down transformer
D. step-up transformer
Your answer would be C.
A step-up transformer is a transformer that raises voltage from main to secondary by having more secondary winding turns than primary winding turns.
Hope this helps; have a great day!
Miles and Joselin are riding a two person long board down an extremely dangerous hill while Chloe watches in horror and Talia in delight. At the end of the hill Alex and Jason are holing a crash pad to stop the dynamic duo from falling off the cliff. If the riders have a combined mass of 200 kg and an acceleration of 30 m/s^2, what Force will they crash the mattress with? Use the correct Force for full credit.
Answer:
They will crash with the force of 6,000N
Explanation:
Force is equal to mass time acceleration. When we multiply 200 kg, the mass, and 30 m/s2, the acceleration, the answer is 6,000.
Help pls !!!
Which statement is true for nuclear reactions but not for chemical reactions?
Answer:
its c
Explanation:
A strand of 10 lights is plugged into a outlet. How can you determine if the lights are connected in series or parrel
Answer:
C) Unscrew one light. If the other lights turn off, it's a series circuit.
Explanation:
THIS IS THE COMPLETE QUESTION BELOW;
A strand of 10 lights is plugged into an outlet. How can you determine if the lights are connected in series or parallel? A) Unscrew one light. If the other lights stay on, it's a series circuit. B) Unplug the strand. If the first light stays on, it's a series circuit. C) Unscrew one light. If the other lights turn off, it's a series circuit. D) Cut the strand in half. If the plugged in half stays on, it's a series circuit.
SERIES CIRCUIT
In this circuit, the components there are in the same path, the entire circuit has the same current, each of the components posses different voltage drop. Hence, failure of one components to work, there will be break in entire circuit then other components cease to work.
PARALLEL CIRCUIT
This circuit has equal voltage drop across all the components, any problem in a component will not has effect on other components.
Therefore, if one want to determine if a light connection is in series or in parallel, one of the light can be unplugged if others stop working it means it's series, if other works it's parallel.
"The gravity of body is not necessary on body. " justify
Answer:
Answer: there are two factors on which centre of mass depends
*its shape and
*the way mass distributed on its shape.
These two factor decide whether centre of mass of gravity lie inside the body or outside the body.
If the body is regular the centre of mass lies inside the body if it is not regular then it lies outside the body
Explanation:
4. Priya notices thet the pressure inside one of her car tyres is too low. She pumps up the tyre to a higher pressure. a) What happens to the number of particles in the car tyre? b) What happens to the distance between particles as pressure increase? c) One of the tyres gets a puncture(small hole) . What happens to the pressure inside the tyre?
Answer:
a) the number of particles increases
b) average distance between them should decrease
c) the number of particles decreases, the pressure must also decrease
Explanation:
a) When the girl pumps to increase the pressure inside the tire she introduces more particles. Therefore the number of particles increases
b) as the volume of the tire does not change and there are more particles, the average distance between them should decrease
c) When a hole is opened, some of the particles inside the tire come out, so as the number of particles decreases, the pressure must also decrease
Comet is seen after a long period of time. Why?
Answer:
Long-period comets have orbital periods longer than 200 years. ... Since it is the sublimation of these volatiles from the nucleus of the comet as it nears the Sun that gives rise to the coma and highly-visible tails, long-period comets have more material with which to put on a show.
Explanation:
How is cell division different for a unicellular organism than it is for a cell in a multicellular organism?
Explanation:
Cells are divided by the reproductive means in unicellular organisms; whereas in multicellular organism they are the means for tissue development and maintenance in multicellular organisms. In adults, tissue renewal rather than development is the most common cell division in which several forms of cells are constantly replaced.
What kind of waves can cause the most damage on the earth's surface?
Answer:
Surface waves, in contrast to body waves can only move along the surface. They arrive after the main P and S waves and are confined to the outer layers of the Earth. They cause the most surface destruction. Earthquake surface waves are divided into two different categories: Love and Rayleigh.
Explanation:
Hope this helped Mark BRAINLIEST!!!
Answer:
Surface waves are the seismic waves that cause the most damage.
Explanation:
a change in earths total isolation would be caused by _____?
Answer:
sunspots
Sunspots are areas in the sun that has a magnetic field is about 2 thousand times stronger than Earth's. Also is much higher than anywhere else on the Sun.
why VR is always less than 1 in Third class lever?
Match the following waves on the EM Spectrum with the correct letter;
Visible Light, Radio Waves, and X Rays
Answer:
(D) is visible light
Explanation:
(F) is xray and (B) is radio
What is the average speed of inchworm 1 at 2 minutes?
I made the chart as clear as I could.
Answer: 2
Explanation:
The average speed of the inchworm 1 at 2 minutes in the given graph is determined as 0.025 m/s.
What is average speed?The average speed of an object is the rate of change of displacement of the object with time.
The average speed of the inchworm 1 at 2 minutes is calculated as follows;
v = D/t
v = 3 m/(2 min x 60 s)
v = 0.025 m/s
Thus, the average speed of the inchworm 1 at 2 minutes is 0.025 m/s.
Learn more about average speed here: https://brainly.com/question/6504879
Which of the following is an example of static electricity?
O Lit light bulb
O Charging battery
O Lightning
O Movie streaming on TV