Assuming that the process is reversible and adiabatic, we can use the following thermodynamic relations to solve the problem. Therefore, the initial quality of water is x₁= 0.197, heat transfer is 52311 KJ
p₁[tex]V1^{k}[/tex]= p2[tex]v2^k[/tex] (where k = cp/cv is the specific heat ratio of water)
v₁/v₂ = x₁/x₂
The specific heat ratio of water can be taken as k = 1.4. The specific volume of water at state 1 can be calculated from the equation of state of water:
p₁= rho₁R T₁
where R = 0.461 kJ/kg-K is the specific gas constant of water vapor, and T1 is the initial temperature. Solving for rho1, we get:
rho₁= p₁/(R T₁) = 120000/(0.461 T₁)
The specific volume of water vapor at state 2 can be calculated from the equation of state of an ideal gas:
p₂ v₂ = m R T₂
where m is the mass of water in the tank, and T2 is the final temperature. Solving for v2, we get:
v2 = m R T₂/p₂
The quality of water at state 2 can be calculated from the definition of quality:
x₂ = (v₂- vf)/(vg - vf)
where vf and vg are the specific volumes of saturated liquid and saturated vapor at pressure p₂, respectively. These can be obtained from steam tables. For p₂ = 4 bar, we find:
vf = 0.001017 m³/kg
vg = 1.6949 m³/kg
The heat transfer during the process can be calculated from the first law of thermodynamics:
Q = m (h₂ - h₁)
where h₁ and h₂ are the specific enthalpies of water at states 1 and 2, respectively. These can also be obtained from steam tables.
Putting all these equations together and solving for x₁ and Q, we get:
v1₁= 0.50/120 = 0.00417 m³/kg
T₁= p₁/(rho1 R) = 281.7 K
v2 = m R T₂/p₂ = (120/18.015) 0.461 T₂/4 = 0.01907 T₂
x₂ = (v₂- vf)/(vg - vf) = (0.01907 T2 - 0.001017)/(1.6949 - 0.001017)
p₁ v₁^k = p₂v₂^k
[tex]p1 v1^(1.4) = p2 v2^(1.4)\\20 (0.00417)^(1.4) = 4 (0.01907 T2)^(1.4)\\ T2 = 242.9 K[/tex]
x₁ = v₁/v₂ x₂= (0.00417/0.01907) x2
= 0.242 x2 = 0.242 (0.8154) = 0.197
h₁ = 693.41 kJ/kg (from steam tables)
h₂ = h₁+ x₁(hfg) = 693.41 + 0.197 (2257.0 - 693.41)
= 1385.9 kJ/kg
Q = m (h₂ - h₁)
= 120 (1385.9 - 693.41) = 52311 kJ
To know more about thermodynamic relation
https://brainly.com/question/31663640
#SPJ4
when we drop 10kg iron and 10kg cotton at the same time from 30ft high, which will reach the ground first? ignore air resistance.
Both objects, the 10kg iron, and the 10kg cotton, will reach the ground at the same time if air resistance is ignored.
This result is because, in the absence of air resistance, the acceleration of a falling object is independent of its mass. All objects, regardless of their mass, will experience the same acceleration due to gravity. This acceleration is approximately 9.8 m/s^2 near the surface of the Earth. Therefore, the time taken for both objects to fall to the ground from the same height will be the same, and they will hit the ground at the same time. However, in the presence of air resistance, the results will be different as air resistance affects objects differently based on their shape and size.
To learn more about air resistance : brainly.com/question/11019447
#SPJ11
a 60co source (which has a half-life of 5.2714 y) is labeled 4.00 mci, but its present activity is found to be 1.3 × 107 bq
The time that has passed since the 60Co source was labeled is 34.8 years.
1 mCi = 37 MBq
So, 4.00 mCi = 148 MBq
We are also given that the present activity (A) is 1.3 × 10^7 Bq.
The half-life (t₁/₂) of 60Co is 5.2714 years. To find the decay constant (λ), we can use the formula:
λ = ln(2) / t₁/₂
λ = ln(2) / 5.2714 y
λ = 0.1315 [tex]y^-1[/tex]
Now we can solve for the time (t) that has passed since the 60Co source was labeled:
A = A₀ * e(-λt)
t = (ln(A₀/A)) / λ
t = (ln(148 × [tex]10^6[/tex] Bq / 1.3 × [tex]10^7[/tex] Bq)) / 0.1315 [tex]y^-1[/tex]
t = 34.8 years
Half-life is the time taken for half of a given sample of a radioactive substance to decay or disintegrate. It is a fundamental concept in nuclear physics and is useful in understanding the properties of radioactive isotopes. Half-life is a measure of the rate at which a substance decays, and it is expressed in units of time, such as seconds, minutes, or years.
The decay process of a radioactive substance is random, which means that it is impossible to predict when a particular atom will decay. However, the half-life of a substance is constant and can be calculated using a mathematical formula. For example, if a substance has a half-life of 10 years, this means that after 10 years, half of the initial amount of the substance will have decayed, and after another 10 years, only a quarter of the original amount will remain, and so on.
To learn more about Half-life visit here:
brainly.com/question/31666695
#SPJ4
steering quickly results in: a. the headlight beams dipping forward. b. a shift of weight fi'om one side of the vehicle. c. both a and b are conect. d. neither a or b are correct.
The correct option is B, Steering quickly results in a shift of weight from one side of the vehicle.
Weight is the force exerted on an object due to gravity. It is the force with which an object is attracted toward the center of the Earth or any other massive body. The weight of an object is proportional to its mass, which is the amount of matter in the object. The formula for weight is W = m × g, where W is weight, m is the mass of the object, and g is the acceleration due to gravity. On Earth's surface, the acceleration due to gravity is approximately 9.81 m/s².
It is important to note that weight is different from mass, although the two terms are often used interchangeably in everyday language. Mass is a measure of the amount of matter in an object and is typically measured in kilograms, while weight is a measure of the force exerted on an object due to gravity and is typically measured in newtons or pounds.
To learn more about Weight visit here:
brainly.com/question/10069252
#SPJ4
what is the difference between the drift velocity in a conductor and the speed of an electrical ignal
The drift velocity in a conductor refers to the net velocity of free electrons in a conductor when a voltage is applied, which is typically very slow, on the order of millimeters per second.
On the other hand, the speed of an electrical signal, also known as the signal propagation speed, refers to the speed at which changes in electric fields and currents propagate through a conductor or other medium, typically at close to the speed of light.
The propagation speed depends on the properties of the medium, such as its dielectric constant and permeability, and can be much faster than the drift velocity of the electrons.
Learn more about The drift velocity
https://brainly.com/question/4269562
#SPJ4
A block of wood weighs 160 N and has a specific gravity of 0.60. Tosink it in fresh water requires an additional downward forceof:A. 54 NB. 64 NC. 96 ND. 110 NE. 240 N
To sink a block of wood weighing 160 N and having a specific gravity of 0.60 in fresh water, an additional downward force of 96 N is required.
The specific gravity of a material is the ratio of its density to the density of water. In this case, the specific gravity of the wood is 0.60, which means its density is 0.60 times the density of water. To sink the wood in water, we need to overcome the buoyant force acting on it, which is equal to the weight of the water displaced by the wood. Since the specific gravity of the wood is less than 1, it will float in water and displace its own weight in water. Therefore, the buoyant force acting on the wood is 160 N.To sink the wood, we need to add a downward force equal to the difference between its weight and the buoyant force. This is equal to (160 N - 0.60 * 1000 kg/m^3 * 9.81 m/s^2 * volume of wood in m^3), where the volume of wood is equal to its weight divided by the density of water. Solving this equation gives us the additional downward force required to sink the wood, which is 96 N. Therefore, the answer is option C.
To learn more about specific gravity:
https://brainly.com/question/9638888
#SPJ11
what did j. j. thomson discover about the cathode ray? what did j. j. thomson discover about the cathode ray? he discovered the mass of the electron. he discovered the charge of the electron. he discovered the existence of the atomic nucleus. he discovered the existence of electrons.
J.J. Thomson discovered the existence of electrons in the cathode ray, which was a beam of negatively charged particles emitted by the cathode in a vacuum tube.
Specifically, he found that the beam could be deflected by an electric or magnetic field, indicating that it was composed of charged particles. By measuring the deflection of the beam and applying equations related to electric and magnetic fields, he was able to determine the charge-to-mass ratio of the particles, which was much smaller than that of any known atom. This led him to propose that the particles were subatomic and he called them "corpuscles", which we now refer to as electrons.
This discovery was significant in the development of atomic theory and laid the foundation for future work on the structure of atoms and the nature of subatomic particles.
Learn more about atomic theory
https://brainly.com/question/28853813
#SPJ4
discuss the electrical-mechanical analogy for oscillating systems, comparing the differential equations, and identifying corresponding terms
The electrical-mechanical analogy is an analogy used to understand the behavior of oscillating systems, both electrical and mechanical.
What is the electrical-mechanical analogy?In the realm of mechanics, a mass's deviance from its equilibrium location is represented by a differential equation:
m( d ²ˣ / dt ² ) + kx = 0
where m is the mass of the object, k is the spring constant, and x is the displacement from equilibrium.
In electrical systems, however, a capacitor's voltage in an RLC circuit can be described using this differential equation:
L ( d ² Q / dt ² ) + R ( dQ / dt ) + ( 1/C ) Q = 0
where L is the inductance, R is the resistance, C is the capacitance, and Q is the charge on the capacitor.
Upon studying these two equations, it becomes clear that the deviation of a mechanical system's mass correlates to the charge on an electrical system's capacitor. Similarly, while a mechanical system identifies its spring constant with the capacitance's inverse, this same correlation exists in electrical systems as well.
Find out more on oscillating systems at https://brainly.com/question/15454378
#SPJ1
a certain wire has a resistance of 100 ω. what is the resistance of a second wire, made of the same material, that is 1/2 as long and has 1/2 the diameter?
The resistance of the second wire is 25 ω.
The resistance of a wire is directly proportional to its length and inversely proportional to its cross-sectional area.
Since the second wire is 1/2 as long as the first wire, its resistance will be half of the first wire's resistance. However, since the second wire has 1/2 the diameter of the first wire, its cross-sectional area will be 1/4 of the first wire's cross-sectional area. Therefore, the resistance of the second wire will be:
R2 = (1/2) * (1/4) * R1
R2 = (1/8) * 100 ω
R2 = 12.5 ω
However, this is the resistance of the wire per unit length. Since the second wire is only 1/2 as long as the first wire, we need to multiply this by 1/2 to get the total resistance of the second wire:
R2 = (1/2) * 12.5 ω
R2 = 6.25 ω
Therefore, the resistance of the second wire is 25 ω.
To Know more about resistance visit;
https://brainly.com/question/28600368
#SPJ11
the frequency of a wave does not change as it passes from one medium to another.what will most likely happen if a light wave moves from the air into a solid?
If a light wave moves from the air into a solid, most likely the wave will be absorbed by the solid.
When a light wave moves from a medium with a higher refractive index into a medium with a lower refractive index, it bends towards the normal (the line perpendicular to the surface of the medium). This is known as refraction. However, if the refractive index of the two media is the same, there will be no bending of the wave and it will pass through the interface without any change in frequency.
In the case of moving from air into a solid, the refractive index of air is lower than that of most solids, so the wave will bend towards the normal as it moves into the solid. However, if the solid has the same refractive index as air, the wave will simply pass through the interface without any change in frequency.
If the refractive index of the solid is higher than that of air, the wave will be partially reflected and partially transmitted through the interface. The amount of transmission and reflection will depend on the angle of incidence of the wave and the refractive indices of the two media.
Learn more about refractive index
https://brainly.com/question/30761100
#SPJ4.
when a light ray passes from water ( n = 1.333) into diamond ( n = 2.419) at an angle of 45 °, its path is
When a light ray passes from water (with a refractive index of 1.333) into diamond (with a refractive index of 2.419) at an angle of 45 degrees, its path is affected by the change in refractive index. Refraction occurs when light passes from one medium to another with a different refractive index, causing the light to bend.
In this case, the light ray will bend towards the normal as it enters the diamond, due to the diamond's higher refractive index. This means that the angle of incidence will be smaller than the angle of refraction.
As the light ray passes through the diamond, it will continue to bend slightly, due to the difference in refractive index between the diamond and air. When the light ray exits the diamond and enters the air, it will bend away from the normal, as the refractive index of air is lower than that of the diamond.
Overall, the path of the light ray passing from water to diamond at an angle of 45 degrees will be curved due to the phenomenon of refraction, with the amount and direction of bending depending on the difference in refractive index between the two materials.
To know more about Refraction click this link-
https://brainly.com/question/13088981
#SPJ11
what is the wavelength of a 1.8 ehz x ray? express your answer in nanometers.
The wavelength of a 1.8 eHz x-ray can be calculated using the formula λ = c/f, where λ is the wavelength, c is the speed of light and f is the frequency. The frequency of a 1.8 eHz x-ray is equivalent to 1.8 x 10^18 Hz.
Substituting this into the formula, we get λ = 3 x 10^8 m/s / (1.8 x 10^18 Hz). Simplifying, we get the wavelength to be approximately 0.1667 nanometers. X-rays have extremely short wavelengths, measured in nanometers, and are therefore highly energetic and can penetrate through dense materials. This makes them useful in medical imaging and industrial applications such as non-destructive testing.
To Learn more about non-destructive testing. Click this!
brainly.com/question/19756261
#SPJ11
How will the kinetic energy, elastic potential energy, and mechanical energy change as the mass oscillates up and down?
The total energy of the system will be the same at all points in the oscillation, but it will change forms as the mass oscillates up and down.
As a mass oscillates up and down, its kinetic energy and elastic potential energy will constantly change. Kinetic energy is the energy an object possesses due to its motion, while elastic potential energy is the energy stored in a system when a force is applied to it. When the mass is at the highest point in its oscillation, its kinetic energy will be at its minimum and its elastic potential energy will be at its maximum. At the lowest point, the kinetic energy will be at its maximum and the elastic potential energy will be at its minimum. In terms of mechanical energy, it will remain constant as long as there is no external force acting on the system.
To learn more about kinetic energy click here https://brainly.com/question/26472013
#SPJ11
Use _____ to reinsulate the hole that a piercing probe makes; do not use _____, which attracts moisture as it cures, potentially causing corrosion.
One should use silicone sealant to reinsulate the hole that a piercing probe makes and avoid using polyurethane sealant. Silicone sealant is a type of sealant that is widely used for sealing gaps and holes due to its high flexibility, adhesion, and water resistance.
It is particularly suitable for sealing electrical components as it has a high resistance to moisture and temperature changes. Moreover, silicone sealant has excellent electrical insulation properties, making it an ideal choice for insulating pierced holes in electrical equipment.
On the other hand, polyurethane sealant should be avoided as it is prone to attracting moisture as it cures, which can lead to corrosion of the metal surrounding the pierced hole. Additionally, polyurethane sealant has poor electrical insulation properties, making it unsuitable for insulating electrical equipment. It is better suited for sealing non-electrical components that are not exposed to moisture or temperature changes.
In summary, silicone sealant is the best choice for reinsulating the hole that a piercing probe makes in electrical equipment due to its flexibility, adhesion, water resistance, and electrical insulation properties, while polyurethane sealant should be avoided due to its tendency to attract moisture and poor electrical insulation properties.
To know more about silicone sealant click this link -
brainly.com/question/18152038
#SPJ11
A diffuse sound field is desired within a theater. The following room treatment would best
contribute to this acoustic characteristic:
(a) the back wall of the stage (behind the performers) is concave in shape
(b) a series of convex panels are suspended from the entire ceiling
(c) velvet curtains are hung on the side walls of the theater
(d) the back wall of the theater is finished with an acoustically reflective material
To create a diffuse sound field within a theater, the goal is to distribute sound energy evenly throughout the space, reducing the presence of distinct echoes and reflections.
Among the given options, the treatment that would best contribute to this acoustic characteristic is:
(c) Velvet curtains hung on the side walls of the theater.
Velvet curtains have a soft and textured surface that can absorb and scatter sound waves, preventing them from reflecting directly back into the audience or creating focused sound reflections. This helps to reduce the presence of strong reflections and echoes, promoting a more diffuse sound field within the theater.
Learn more about diffuse sound field here:
https://brainly.com/question/18534026
#SPJ11
a 10-kg rock falls from a height of 8.0 m above the ground. what is the kinetic energy of the rock just before it hits the ground?
The kinetic energy of the rock just before it hits the ground is approximately 784.8 J.
The potential energy of the rock due to its position at a height of 8.0 m above the ground can be calculated using the formula:
PE = mgh
where m is the mass of the rock, g is the acceleration due to gravity (which is approximately 9.81 m/s^2), and h is the height of the rock above the ground.
Substituting the given values, we get:
PE = 10 kg * 9.81 m/s^2 * 8.0 m = 784.8 J
As the rock falls, its potential energy is converted to kinetic energy, which can be calculated using the formula:
KE = 1/2 * mv^2
where v is the velocity of the rock just before it hits the ground.
The law of conservation of energy states that the total energy of the system (in this case, the rock and the Earth) remains constant, so the potential energy at the top of the fall is converted to kinetic energy just before the rock hits the ground.
Therefore, the kinetic energy of the rock just before it hits the ground is equal to its initial potential energy:
KE = PE = 784.8 J
So the kinetic energy of the rock just before it hits the ground is approximately 784.8 J.
Visit to know more about Kinetic energy:-
brainly.com/question/8101588
#SPJ11
under 14 cfr part 91, what are the minimum number of hours that must pass after a person consumes alcohol before they may act as a crewmember?
Under 14 CFR Part 91, a crewmember must wait at least 8 hours after consuming alcohol before acting as a crewmember of a civil aircraft.
No individual under the influence of alcohol may perform or try to act as a crewmember of a civil aircraft, in accordance with 14 CFR Part 91. A person may not work as a crew member of a civil aircraft within eight hours after ingesting alcohol, while impaired by alcohol, or while using any drug that impairs their ability to make decisions that are unsafe. The 8-hour "bottle-to-throttle" regulation was put in place by the FAA to make sure that crew members had enough time to get the alcohol out of their systems before flying an aircraft.
learn more about a crewmembe here:
https://brainly.com/question/28907225
#SPJ11
In all three types of radioactive decay, what value is conserved in addition to electric charge, energy, and momentum?atomic numberneutron numbernucleon numbernone of the given answers
The value that is conserved in addition to electric charge, energy, and momentum in all three types of radioactive decay is the nucleon number.
The nucleon number is the total number of protons and neutrons in an atom's nucleus. During radioactive decay, the nucleus may undergo a change in its nucleon number by emitting or absorbing particles such as alpha particles, beta particles, or gamma rays. However, the total nucleon number before and after the decay remains the same, which is a fundamental principle of conservation in nuclear physics.
In all three types of radioactive decay, the value that is conserved in addition to electric charge, energy, and momentum is the nucleon number. The nucleon number represents the total number of protons and neutrons in a nucleus, and it remains constant throughout the decay process.
To know more about electric charge visit:-
https://brainly.com/question/29736640
#SPJ11
how will the brightness of bulb 1 compare before and after the switch next to bulb 3 is closed. a. the brightness will decrease. b. the brightness will be the same. c. the brightness will increase. d. it's impossible to determine from the given information.
The answer is (b) the brightness will be the same. Closing the switch next to bulb 3 will not have any effect on the brightness of bulb 1.
This is because the circuit is in parallel, which means that each bulb is connected to the battery separately. So, closing the switch next to bulb 3 will only affect the circuit between bulb 3 and the battery. It will not affect the circuit between bulb 1 and the battery. Therefore, the brightness of bulb 1 will remain the same before and after the switch is closed. The circuit could be wired in a variety of ways, with different resistances and current flows, which would affect the brightness of bulb 1.
Learn more about brightness here:
brainly.com/question/14970890
#SPJ11
a puck moves 2.35 m/s in a -22.0 direction. a hockey stick pushes it for 0.215 s, changing it's velocity to 6.42 m/s in a 50.0 direction. what is delta x
To find the displacement or change in position, delta x, of the puck, we can use the formula: delta x = (1/2) * (v_i + v_f) * t
delta x = (1/2) * (v_i + v_f) * t
where:
v_i = initial velocity
v_f = final velocity
t = time interval
Using the given information, we have:
v_i = 2.35 m/s in a -22.0 direction
v_f = 6.42 m/s in a 50.0 direction
t = 0.215 s
We first need to break down the initial and final velocities into their x and y components. To do this, we can use trigonometry:
v_i,x = 2.35 m/s * cos(-22.0°) ≈ 2.18 m/s
v_i,y = 2.35 m/s * sin(-22.0°) ≈ -0.88 m/s
v_f,x = 6.42 m/s * cos(50.0°) ≈ 4.95 m/s
v_f,y = 6.42 m/s * sin(50.0°) ≈ 4.94 m/s
Now we can plug these values into the formula:
delta x = (1/2) * (v_i,x + v_f,x) * t
= (1/2) * (2.18 m/s + 4.95 m/s) * 0.215 s
≈ 0.79 m
Therefore, the displacement of the puck, or its change in position, is approximately 0.79 meters.
Learn more about velocity : brainly.com/question/14365341
#SPJ11
telescopes designed to study the earliest stages in galactic lives should be optimized for observations in infrared light
Telescopes designed to study the earliest stages in galactic lives should be optimized for observations in infrared light. Infrared light has longer wavelengths than visible light, allowing it to penetrate dust and gas clouds more effectively.
This is particularly important for studying the earliest stages of galactic evolution, as these stages often involve dense regions of dust and gas that can obstruct visible light observations. By observing in the infrared spectrum, astronomers can detect the faint emissions from warm dust, molecular clouds, and newly forming stars that are otherwise hidden in the visible range. This enables them to study processes such as star formation, protoplanetary disks, and the evolution of galaxies in their early stages.Therefore, optimizing telescopes for observations in infrared light is crucial for gaining insights into the earliest stages of galactic lives and unraveling the mysteries of galactic evolution.
To know more about telescopes, click here https://brainly.com/question/31634676
#SPJ11
a battery-driven percy engine goes around a track (radius 25 cm) in 59 seconds. what is its angular speed?
The angular speed of the battery-driven percy engine can be calculated using the formula: angular speed = 2π/T, where T is the time taken to complete one full rotation around the track. In this case, the time taken is 59 seconds, so:
angular speed = 2π/59
angular speed = 0.106 radians/second
Alternatively, we can use the formula: angular speed = linear speed / radius. The linear speed of the percy engine can be calculated by dividing the circumference of the track by the time taken to complete one full rotation:
circumference = 2π × radius = 2π × 25 cm = 157.08 cm
linear speed = circumference / T = 157.08 cm / 59 seconds = 2.66 cm/second
Therefore, the angular speed can be calculated as:
angular speed = linear speed / radius = 2.66 cm/second / 25 cm
angular speed = 0.106 radians/second
So, the angular speed of the battery-driven percy engine going around a track with a radius of 25 cm is 0.106 radians/second.
To Learn more about angular Click this!
brainly.com/question/31801871
#SPJ11
A piece of cheese with a mass of 1. 06kgis placed on a vertical spring of negligible mass and a force constantk= 1700N/mthat is compressed by a distance of 17. 1cm.
When the spring is released, how high does the cheese rise from this initial position? (The cheese and the spring are not attached. )
Use 9. 81m/s^2for the acceleration due to gravity. Express your answer using two significant figures
The cheese rises to a height of 2.37 meters above its initial position.
The potential energy stored in the compressed spring is given by:
U = (1/2)kx^2
where k is the spring constant and x is the distance the spring is compressed. Plugging in the given values, we get:
U = (1/2)(1700 N/m)(0.171 m)^2 = 24.6 J
When the spring is released, this potential energy is converted to kinetic energy as the cheese moves upward. At the highest point of its motion, all of the kinetic energy will have been converted back to potential energy (ignoring any energy lost to friction or air resistance). At this point, the cheese will have a velocity of zero.
The potential energy at the highest point can be calculated using the equation:
U = mgh
where m is the mass of the cheese, g is the acceleration due to gravity, and h is the height above the initial position. We can solve for h by equating the potential energies at the two positions:
U = mgh
24.6 J = (1.06 kg)(9.81 m/s^2)h
h = 2.37 m
Therefore, the cheese rises to a height of 2.37 meters above its initial position.
Visit to know more about Initial position:-
brainly.com/question/28603433
#SPJ11
At a science museum, a stationary bicycle is connected to an electric generator. By pedaling steadily, a museum visitor is able to keep a 75-watt light bulb fully lit for 45 seconds.What is the total energy, in kilojoules, consumed by the light bulb during this time? In kJ
The total energy consumed by the light bulb during the 45 seconds is 3.375 kilojoules.
Energy = Power x Time
We are given that the power output of the stationary bicycle is 75 watts and the time for which the light bulb is fully lit is 45 seconds. Therefore, we can calculate the energy consumed by the light bulb as follows:
Energy = Power x Time
Energy = 75 watts x 45 seconds
Now we need to convert the units from watts and seconds to kilojoules. We know that 1 watt = 1 joule/second and 1 kilojoule = 1000 joules. Therefore:
Energy = 75 watts x 45 seconds
Energy = 3375 joules
Energy = 3.375 kilojoules
So the total energy consumed by the light bulb during the 45 seconds is 3.375 kilojoules.
To know more about energy, refer
https://brainly.com/question/13881533
#SPJ11
The wave speed in an aluminum wire with a radius of 1.00 mm is 120 m/s. What is the tension in the wire? The density of aluminum is 2.70 x10^3 kg/m^3.What formula do we use and how do we solve?
We can use the formula for wave speed on a string: v = sqrt(T/μ), where v is the wave speed, T is the tension, and μ is the mass per unit length of the string. To solve for T, we can rearrange the equation to T = μv^2.
Substituting the given values, we have:
μ = density x cross-sectional area = 2.70 x 10^3 kg/m^3 x π(1.00 x 10^-3 m)^2 = 8.51 x 10^-6 kg/m
v = 120 m/s
Plugging these values into the formula, we get:
T = μv^2 = (8.51 x 10^-6 kg/m) x (120 m/s)^2 = 12.3 N
Therefore, the tension in the aluminum wire is 12.3 N.
Learn more about the cross-sectional area here:- brainly.com/question/20532494
#SPJ11
if the intensity of radiation 3.0 cm from a source is 300. mci, what is the intensity 1.0 cm from the source?
The intensity of radiation 1.0 cm from the source is 900. mci the intensity of radiation from a point source is inversely proportional to the square of the distance from the source. This is known as the inverse square law.
Using this law, we can calculate the intensity of radiation at 1.0 cm from the source as follows:
[tex](3.0 cm / 1.0 cm)² = 9[/tex]
So the intensity at 1.0 cm is 9 times higher than the intensity at 3.0 cm.
Therefore,
[tex]300. mci x 9 = 2700. mci[/tex]
So the intensity of radiation at 1.0 cm from the source is 2700. mci or 900. mci if we round to one significant figure.
Learn more about intensity here:
https://brainly.com/question/17583145
#SPJ11
Give practical everday uses of absobers and emmiters
Absorbers and emitters are used in everyday applications such as insulation, food preservation, lighting, solar energy, and clothing to regulate the transfer of heat and energy.
Absorbers are materials or substances that absorb energy, such as heat or light, from their surroundings. They can be used in a variety of applications to regulate temperature, preserve food, and improve comfort.
Absorbers and emitters are important in a variety of everyday applications, such as:
1. Insulation: Absorbers and emitters are commonly used in insulation to regulate the transfer of heat. Absorbers absorb heat, while emitters emit it, allowing for more efficient temperature regulation in buildings and homes.
2. Food Preservation: Absorbers are used in food packaging to absorb oxygen and moisture, helping to preserve the quality and freshness of the food.
3. Lighting: Emitters are used in lighting, such as LED bulbs, to emit light in a more energy-efficient manner. They also emit less heat than traditional incandescent bulbs, making them safer and more cost-effective.
4. Solar Energy: Emitters are used in solar panels to emit light as electricity. Absorbers are also used to absorb sunlight, increasing the efficiency of the solar panel.
5. Clothing: Absorbers are used in clothing, such as sweat-wicking fabrics, to absorb moisture from the body and keep the wearer dry and comfortable.
Absorbers and emitters work by either absorbing or emitting energy, such as heat or light. Absorbers absorb energy, while emitters release it. In many cases, both absorbers and emitters are used together to regulate the flow of energy, such as in insulation or solar panels. In other cases, only one is used, such as in clothing or food packaging. Overall, absorbers and emitters are important in many everyday applications, helping to regulate temperature, preserve food, conserve energy, and improve comfort.
Therefore, In order to control the passage of heat and energy, absorbers and emitters are employed in commonplace applications like insulation, food preservation, lighting, solar energy, and clothing.
To learn more about Nephelometry click:
https://brainly.com/question/29708113
#SPJ1
for an rlc ac circuit, the rms current is 10 a. if the impedance is 12 kω when the voltage leads the current by 39°, find the average power of the circuit. 190 kw 930 kw 93 kw 47 kw
The average power of an RLC AC circuit can be calculated using the formula P =VIcos(φ), So, the average power of the circuit is 93 kW. So, the correct answer is C).
Using the given information, the average power of the circuit can be calculated using the formula P = VIcos(φ), where V is the RMS voltage, I is the RMS current, and φ is the phase angle between voltage and current.
Here, the current is given as 10 A RMS and the impedance is given as 12 kΩ when voltage leads the current by 39°.
So, the RMS voltage can be calculated using the formula Z = V/I, where Z is the impedance.
Z = 12 kΩ = (V/RMS current)
V = Z x RMS current = 12 kΩ x 10 A = 120 kV
Now, using the formula P = VIcos(φ), where φ = 39°, we get
P = (120 kV) x (10 A) x cos(39°) = 93 kW
Therefore, the average power of the circuit is 93 kW. The correct option is (c).
To know more about power of circuit:
https://brainly.com/question/30497146
#SPJ4
a force f acts on a rigid object. under what conditions will a force produce a force - couple system acting on the object.
A force F acting on a rigid object will produce a force-couple system when the force is not applied at the object's center of mass.
In other words, if the force is applied at a point other than the object's center of mass, a torque or moment will be produced, creating a couple.
The effect of the couple on the rigid object depends on the direction and magnitude of the torque created. A torque produces a rotational motion, causing the object to rotate about its center of mass. The magnitude of the torque is equal to the force multiplied by the distance between the force's line of action and the object's center of mass.
If the force is applied perpendicular to the object's center of mass, the couple will create a pure rotational motion, where the object rotates without any translational motion. However, if the force is applied at an angle to the object's center of mass, both translational and rotational motion will occur.
In summary, when a force is applied to a rigid object at a point other than its center of mass, a force-couple system is created. The couple produces a torque, which causes rotational motion of the object about its center of mass, with the magnitude of the torque dependent on the distance between the force and the center of mass.
To learn more about force click on,
https://brainly.com/question/28439782
#SPJ4
Complete question is:
A force F acts on a rigid object. Under what conditions will the force produce a force - couple system acting on the object. What will be the effect of the couple on the rigid object
A circuit contains a D-cell battery, a switch, a 20-Ωresistor, and three 20-mF capacitors. The capacitors areconnected in parallel, and the parallel connection ofcapacitors are connected in series with the switch, theresistor and the battery. (a) What is the equivalentcapacitance of the circuit? (b) What is the RC timeconstant? (c) How long before the current decreases to50% of the initial value once the switch is closed?
Explanation:
(a) To find the equivalent capacitance of the circuit, we can use the formula for the equivalent capacitance of capacitors in parallel:
C_eq = C1 + C2 + C3
where C1, C2, and C3 are the capacitances of the three capacitors. Substituting the given values, we get:
C_eq = 20 mF + 20 mF + 20 mF = 60 mF = 6.0 × 10^-5 F
Therefore, the equivalent capacitance of the circuit is 6.0 × 10^-5 F.
(b) To find the RC time constant of the circuit, we can use the formula:
τ = RC
where R is the resistance of the resistor and C is the equivalent capacitance of the circuit. Substituting the given values, we get:
τ = (20 Ω)(6.0 × 10^-5 F) = 1.2 × 10^-3 s
Therefore, the RC time constant of the circuit is 1.2 × 10^-3 s.
(c) To find the time it takes for the current to decrease to 50% of the initial value, we can use the formula:
I = I0 e^(-t/τ)
where I0 is the initial current, I is the current after a time t, τ is the RC time constant, and e is the mathematical constant approximately equal to 2.71828. Solving for t, we get:
t = -τ ln(I/I0)
Substituting the given values, we get:
t = -(1.2 × 10^-3 s) ln(0.5) = 8.3 × 10^-4 s
Therefore, it takes 8.3 × 10^-4 s for the current to decrease to 50% of the initial value once the switch is closed.
an airplane has a mass of 1.10 104 kg, and each wing has an area of 39.0 m2. during level flight, the pressure on the lower wing surface is 6.00 104 pa. (a) suppose the lift on the airplane were due to a pressure difference alone. determine the pressure on the upper wing surface.
The pressure on the upper wing surface is 4.10 x 10^3 Pa.
The lift force on an airplane wing is due to the pressure difference between the upper and lower surfaces of the wing. According to Bernoulli's principle, the pressure of a fluid decreases as its speed increases. Therefore, the air moving over the curved upper surface of the wing must have a lower pressure than the air moving over the flat lower surface of the wing.
The lift force can be calculated using the formula:
L = Cl * ρ * A * v^2 / 2
where L is the lift force, Cl is the lift coefficient, ρ is the density of the air, A is the area of the wing, and v is the speed of the air.
Since the airplane is in level flight, the lift force is equal to the weight of the airplane:
L = mg
where m is the mass of the airplane and g is the acceleration due to gravity.
We can use these two equations to find the speed of the air over the wing:
mg = Cl * ρ * A * v^2 / 2
v^2 = 2mg / (Cl * ρ * A)
v = sqrt(2mg / (Cl * ρ * A))
Let's assume that the lift coefficient is the same for both the upper and lower surfaces of the wing. Then, the lift force on each wing is:
L/2 = Cl * ρ * A * v^2 / 4
The pressure difference between the upper and lower surfaces of the wing can be found using the formula:
ΔP = 2 * (L/2) / A
Substituting the expressions for L/2 and v^2, we get:
ΔP = Cl * ρ * v^2
ΔP = Cl * ρ * (2mg / (Cl * ρ * A))
ΔP = 2mg / A
Substituting the given values, we get:
ΔP = 2 * (1.10 x 10^4 kg) * 9.81 m/s^2 / (39.0 m^2)
ΔP = 5.59 x 10^4 Pa
Since the pressure on the lower wing surface is given as 6.00 x 10^4 Pa, the pressure on the upper wing surface is:
Pupper = Plower - ΔP
Pupper = (6.00 x 10^4 Pa) - (5.59 x 10^4 Pa)
Pupper = 4.10 x 10^3 Pa
Therefore, the pressure on the upper wing surface is 4.10 x 10^3 Pa.
Visit to know more about Pressure:-
brainly.com/question/28012687
#SPJ11