When linked across a 20-volt battery, a length of 5.56 metres of wire is required to provide 48 watts of electricity.
We may utilise the power in a resistor formula, which is:
[tex]P = V^2 / R[/tex]
where P denotes power, V denotes voltage, and R denotes resistance.
This formula can be rearranged to account for resistance:
[tex]R = V^2 / P[/tex]
We also know that the resistance of a wire may be computed using the formula: resistivity (), length (L), and cross-sectional area (A).
R = ρL / A
We may calculate the needed length of wire by combining these two equations:
ρL / A = [tex]V^2 / P[/tex]
L = A[tex]V^2[/tex] / (P ρ)
Plugging in the given values, we get:
L = (4.0 x [tex]10^-6 m^2[/tex]) ([tex]20 V)^2[/tex]/ (48 W) (3.0 x [tex]10^8[/tex] Ω·m)
L = 5.56 m
As a result, a wire length of 5.56 metres is required to generate 48 watts of electricity when linked across a 20-volt battery.
Therefore, the length of wire required is 1.11 km.
Learn more about length
https://brainly.com/question/30100801
#SPJ4
in a study of the photoelectric effect, a researcher shines low-intensity visible light with a wavelength of 650 nm on a sample of metal. she notices that no photoelectrons are produced. what would happen if she were to increase the intensity of the light by a factor of 10?:
Increasing the intensity of the light by a factor of 10 would increase the number of photoelectrons produced.
The photoelectric effect is a phenomenon in which electrons are emitted from a material when it absorbs electromagnetic radiation, such as light. The energy of the radiation must be greater than the work function of the material for electrons to be emitted.
Increasing the intensity of the light increases the number of photons striking the surface of the metal, which increases the likelihood of electrons being emitted. Therefore, increasing the intensity of the light by a factor of 10 would result in the emission of photoelectrons.
To learn more about photoelectrons, here
https://brainly.com/question/16772624
#SPJ4
look again at the visible-light view of m82. what is the source of the white and blue light that dominates the image?
In the visible-light view of M82, the source of the white and blue light that dominates the image is mainly due to the presence of young, massive stars. These stars emit high amounts of energy, which results in a strong blue and white glow.
The white and blue light in the visible-light view of M82 is primarily coming from young, hot, massive stars that are forming in the galaxy's intense starburst regions. These stars emit large amounts of ultraviolet radiation, which ionizes the surrounding gas and causes it to glow brightly in visible light. Additionally, some of the blue light may be due to scattered starlight off of dust particles in the galaxy's disk.
The blue light comes from the hot, young stars, while the white light is a combination of light emitted by various types of stars within the galaxy. The high star formation rate in M82 contributes to the abundance of these bright stars and the overall appearance of the galaxy.
To know more about ultraviolet radiation:
https://brainly.com/question/30547511
#SPJ11
at 2.1 km from the transmitter, the peak electric field of a radio wave is 350 mv/m . what is the peak electric field 10 km from the transmitter?
The peak electric field 10 km from the transmitter is approximately 15.435 mV/m.
To find the peak electric field 10 km from the transmitter, we can use the inverse square law.
This law states that the intensity of a wave (such as the electric field in this case) is inversely proportional to the square of the distance from the source.
Here's a step-by-step explanation:
1. Note the initial distance (d1) and electric field (E1):
d1 = 2.1 km, E1 = 350 mV/m.
2. Convert d1 to meters:
d1 = 2100 m.
3. Note the final distance (d2):
d2 = 10 km.
4. Convert d2 to meters:
d2 = 10,000 m.
5. Use the inverse square law formula:
E2 = E1 * (d1²) / (d2²).
6. Plug in the values:
E2 = 350 * (2100²) / (10,000²).
7. Calculate E2:
E2 ≈ 15.435 mV/m.
Learn more about electric field:
https://brainly.com/question/14372859
#SPJ11
Green laser pointers emit light with a wavelength of 532 nm. Do research on the type of laser used in this type of pointer and describe its operation. Indicate whether the laser is pulsed or continuous.
Pulsed lasers are used in specific applications where short bursts of laser light are needed, such as in laser ranging, lidar, or certain medical procedures.
What is Wavelength?
Wavelength is a term used in physics to describe the distance between two consecutive points of a wave that are in phase, or the distance over which a wave completes one cycle. It is commonly denoted by the Greek letter lambda (λ) and is usually measured in units such as meters (m), nanometers (nm), or angstroms (Å).
Green laser pointers typically use a type of laser known as a diode-pumped solid-state (DPSS) laser to generate laser light at a wavelength of 532 nm, which corresponds to green light in the visible spectrum. DPSS lasers are a type of laser that uses a solid-state crystal or material as the gain medium, which is pumped by a diode laser to achieve laser emission.
Learn more about Wavelength from the given link
https://brainly.com/question/10750459
#SPJ1
15) monochromatic coherent light shines through a pair of slits. if the distance between these slits is decreased, which of the following statements are true of the resulting interference pattern? (there is more than one correct choice.) a) the distance between the maxima stays the same. b) the distance between the maxima decreases. c) the distance between the minima stays the same. d) the distance between the minima increases. e) the distance between the maxima increases.
Two of the correct statements regarding this are:
b) the distance between the maxima decreases
d) the distance between the minima increases
When monochromatic coherent light shines through a pair of slits, an interference pattern is created. This pattern is dependent on the distance between the slits. If the distance between the slits is decreased, the resulting interference pattern will be affected.
When the distance between the slits is decreased, the interference pattern becomes wider, and the distance between the maxima decreases. The distance between the minima, on the other hand, increases.
This is because the interference pattern is created by the interaction of waves, and when the distance between the slits is decreased, the waves interfere with each other differently.
This causes the pattern to shift and change. Therefore, the resulting interference pattern is affected by the distance between the slits.
To learn more about : minima
https://brainly.com/question/29512870
#SPJ11
. for schrodinger's equation of the h2 molecule, the kinetic energy has contributions from a. electrons only b. nuclei only c. both electrons and nuclei d. only one electron and one nucleus
The kinetic energy in Schrödinger's equation for the H2 molecule includes contributions from both electrons and nuclei. Thus the correct option is C.
The kinetic energy term in Schrödinger's equation for the H2 molecule refers to the energy involved in the motion of the particles. The H2 molecule comprises two hydrogen nuclei and two electrons, therefore the electrons and the nuclei both contribute to the kinetic energy.
The nuclei contribute to the kinetic energy by their mobility, whereas the electrons do so through their wave-like behaviour. The H2 molecule's kinetic energy term in Schrödinger's equation includes contributions from both electrons and nuclei, making option C the right response.
Learn more about kinetic energy:
https://brainly.com/question/30285686
#SPJ4
The kinetic energy in Schrödinger's equation for the H2 molecule includes contributions from both electrons and nuclei. Thus the correct option is C
explanation - For Schrödinger's equation of the H2 molecule, the kinetic energy has contributions from both electrons and nuclei. This is because the kinetic energy term in the equation accounts for the motion of all particles in the system, which in this case includes both the electrons and nuclei of the H2 molecule. Therefore, options a, b, and d are incorrect.
To know more about the schrodinger equation, click on this -
brainly.com/question/31441754
#SPJ11
a pendulum is swinging upward and is halfway toward its highest position, as shown, when the string breaks. which of the paths shown best represents the one that the ball would take after the string breaks?
The option A is best representation of the path that the ball would take after the string breaks.
When the string of a pendulum breaks, the ball's path will follow the laws of motion, specifically the law of conservation of energy. As the ball was halfway to its highest position, it had a certain amount of potential energy.
When the string broke, this potential energy would convert to kinetic energy, causing the ball to move in a straight line tangent to the point where the string broke.
Therefore, the path that the ball would take after the string breaks would be a straight line away from the pivot point of the pendulum, as shown in option A. The other paths shown do not follow the laws of motion and do not account for the conservation of energy. Option (A) is the correct answer.
To learn more about : string
https://brainly.com/question/24994188
#SPJ11
Note the full question is
A pendulum is swinging upward and is halfway toward its highest position, as shown, when the string breaks. which of the paths shown best represents the one that the ball would take after the string breaks?
A) A
B) B
C) C
D) D
E) E
A bow is drawn so that it has 40 J of potential energy. When fired, the arrow will have a kinetic energy of: Select one: O a. 80) o b. 20) O 0.60) O d. 40)
When a bow is drawn and has 40 J of potential energy, the arrow's kinetic energy when fired will be:
Your answer: d. 40 J
Explanation:
Potential energy is the energy that an object possesses due to its position, configuration, or state of being. It is stored energy that has the potential to do work in the future. The amount of potential energy that an object has depends on its position or configuration relative to other objects or systems. For example, a bow that is pulled back has potential energy that can be released as kinetic energy when it is released.
Kinetic energy, on the other hand, is the energy that an object possesses due to its motion. It is the energy that an object possesses because it is in motion and is able to do work by causing a change in another object's motion or position. The amount of kinetic energy that an object has depends on its mass and its velocity. For example, a moving car has kinetic energy that can be transferred to another object if it collides with it.
When the bow is drawn, it stores potential energy. When fired, this potential energy is converted into kinetic energy for the arrow. In an ideal situation with no energy loss, the arrow's kinetic energy will be equal to the bow's potential energy. Therefore, the arrow will have a kinetic energy of 40 J.
To learn more about Potential Energy and Kinetic Energy. Please Visit:
https://brainly.com/question/30176483
#SPJ11
block 1 is stacked on top of block 2. block 2 is connected by a light cord to block 3, which is pulled along a frictionless surface with a force f as shown in the diagram. block 1 is accelerated at the same rate as block 2 because of the frictional forces between the two blocks. if all three blocks have the same mass m, what is the minimum coefficient of static friction between block 1 and block 2?
The minimum coefficient of static friction between block 1 and block 2 is (F-f-m*a)/g, which can be calculated by equating the horizontal forces acting on block 1.
How to find the minimum coefficient of static friction between block 1 and block 2?The minimum coefficient of static friction between block 1 and block 2 can be calculated by equating the forces acting on block 1 in the horizontal direction. Since block 1 and block 2 have the same acceleration, the net force on block 1 is:
F - f - μ_smg = m*a
where F is the force applied to block 3, μ_s is the coefficient of static friction between block 1 and block 2, and g is the acceleration due to gravity.
Since block 1 and block 2 have the same mass, we can simplify the above equation to:
F - f - = ma
Solving for μ_s, we get:
μ_s = (F - f - m*a)/g
Therefore, the minimum coefficient of static friction between block 1 and block 2 is (F - f - m*a)/g.
Learn more about Minimum coefficient
brainly.com/question/31157416
#SPJ11
help me please oml 2 one
Color: Both the bromine gas and steak have a brownish color.
What is bromine gas?Bromine gas is a reddish-brown, nonflammable, and highly toxic gas with a very strong, unpleasant odor. It is composed of two heavy, diatomic, halogen molecules, Br2, and is the only nonmetal element that exists as a liquid at room temperature. Bromine gas is denser than air and is soluble in water and organic solvents.
Texture: The bromine gas is a gas and therefore has no texture, while the steak is solid and has a firm texture.
Temperature: The bromine gas is a gas and therefore has a lower temperature than the steak, which is at room temperature.
Bromine Gas and Juice:
Color: The bromine gas is brownish and the juice is a yellowish or orange color.
Texture: The bromine gas is a gas and therefore has no texture, while the juice is a liquid and has a smooth texture.
Temperature: The bromine gas is a gas and therefore has a lower temperature than the juice, which is at room temperature.
To learn more about bromine gas
https://brainly.com/question/1126306
#SPJ1
true or false an electric current produces a magnetic field and a magnetic field can be used generate electricity
The surface of which jovian moon most resembles the pack ice of the Arctic Ocean? A) Amalthea B) Io C) Europa D) Ganymede E) Callisto.
water is drawn from a well in a bucket tied to the end of a rope whose other end wraps around a cylinder of mass 50 kg and diameter 25 cm. as you turn this cylinder with a crank, the rope raises the bucket. if the mass of a bucket of water is 20 kg, what torque must you apply to the crank to raise the bucket of water at a constant speed?
m_c (mass of cylinder)=50 kg
d=25 cm so r=12.5 cm = 0.125 m m_b
(mass of bucket)=20 kg
So using the equations: RT = � = I � RT= I � (m_b)g-T= (m_b)aR And from what I understand, this is the same as the tangential acceleration? (m_b)g-T=(m_b) � r = F T= ( i � ) / r (m_b)g -(( i � ) / r ) = m � r � ( ((m_b)r) + (I /R ) ) = (m_b)g Leaving us with the final : � = ((m_b)g)/(((m_b)r) + (I /r)) Using this equation, I found I = 0.390625 and the final answer would be 35 rad/s^2 Sorry for such a long post--this is my first time on the website and I read the rules so hopefully I've done everything correctly! Thank you all!
/
on the centered zipper, what is the only part of the work that is done on the outside of the garment?
The only part of the work that is done on the outside of the garment is the basting or pinning of the zipper tape to the fabric.
The rest of the work is done on the inside of the garment. The zipper teeth are inserted between the layers of the fabric and the seam is sewn in place. The seam is then pressed open and the zipper is opened up to expose the teeth.
The zipper tape is then folded back and stitched in place, creating a clean finish on the inside of the garment. The final step is to topstitch the zipper on the outside of the garment, which reinforces the zipper and adds a decorative touch.
Overall, the centered zipper is a popular and versatile choice for many types of garments and can be easily customized to suit individual preferences.
To learn more about : garment
https://brainly.com/question/28264851
#SPJ11
Please help I need to answer fast the fate of my graduation depends on it.
First, we need to find the total mass of the system by adding the masses of the two objects: m_total = m1 m2 = 50.0 kg 75.0 kg = 125.0 kg Next, we can plug in the given force and mass values into the equation: F = ma 40.0 N = 125.0 kg * a Solving for a: a = 40.0 N
125.0 kg * a
Solving for a:
a = 40.0 N / 125.0 kg
a = 0.32 m/s^2
Therefore, the acceleration of the system is 0.32 m/s^2.
a circuit breaker is rated for a current of 15 a rms at a voltage of 240 v rms. (a) what is the largest value of imax that the breaker can carry?
The largest value of I_max that the breaker can carry is approximately 21.21 A.
Given a circuit breaker rated for 15 A RMS at 240 V RMS, we want to find the largest value of Imax (maximum current) that the breaker can carry. To do this, we'll use the following formula:
I_max = √2 * I_RMS
Where I_RMS is the rated current in RMS, which is 15 A in this case.
Substitute the value of I_RMS into the formula:
Imax = √2 * 15 A
Calculate the value of Imax:
Imax ≈ 21.21 A
Therefore approximately 21.21 A is the largest value of Imax that the breaker can carry.
More on circuit breaker: https://brainly.com/question/29480920
#SPJ11
thermal expansion may cause an equipment or piping system overpressure when the liquid is blocked-in
Thermal expansion is a phenomenon in which materials expand when they are heated and contract when they are cooled. This can be a problem in industrial equipment or piping systems that contain liquids, especially when the liquid is blocked-in and cannot move freely.
When the temperature of the liquid increases due to an external heat source, such as a nearby furnace or the sun, the liquid will expand and cause an increase in pressure within the equipment or piping system. This increase in pressure can lead to overpressure, which can be dangerous and can potentially cause equipment failure or system rupture.
It is important to account for thermal expansion when designing industrial equipment and piping systems to ensure that they can safely withstand the changes in pressure caused by temperature fluctuations.
Learn more about equipment ,
https://brainly.com/question/30230359
#SPJ4
.A cannonball is launched upward with a velocity of 73.5 m/s at an angle of 20 degrees above the
horizontal.
(a) How long is the cannonball in the air?
(b) How far away does it land?
() How high does it travel? Cut your time in half!
Answer:
time of flight=( 2U sinx ) ÷ g
Explanation:
a)
u=73.5m/s , x= 20° , g =10m/s^2 then t= {2×73.5 × sin 20°} ÷ 10 = 134.2 ÷ 10 = 13.42 sec b) range is the distance, range= (u^2 sin 2 x ) ÷g = ({73.5 }^2 × sin 2 × 20 )÷ 10 =4025.3÷10 = 402.53meters. I couldn't finish the question so sorry
what does the technique of interferometry allow?what does the technique of interferometry allow?it allows two or more telescopes to obtain a total light-collecting area much larger than the total light-collecting area of the individual telescopes.it allows us to determine the chemical composition of stars.it allows two or more telescopes to obtain the angular resolution of a single telescope much larger than any of the individual telescopes.it allows the same telescope to make images with both radio waves and visible light.it allows astronomers to make astronomical observations without interference from light pollution.
The technique of interferometry allows two or more telescopes to obtain the angular resolution of a single telescope much larger than any of the individual telescopes.
This is achieved by combining the signals received by the telescopes to create a single image with a higher resolution. Interferometry is especially useful for studying objects with small angular sizes, such as stars and planets.
Additionally, interferometry allows astronomers to make astronomical observations without interference from light pollution, as it can separate the signals from the object being observed from the background light.
However, interferometry does not directly determine the chemical composition of stars, although it can provide information about their temperature and other physical properties.
Learn more about interferometry:
https://brainly.com/question/30054443
#SPJ11
A 3. 0-kg mass moving in the positive x direction with a speed of 10 m/s collides with a 6. 0-kg mass initially at rest. After the collision, the speed of the 3. 0-kg mass is 8. 0 m/s, and its velocity vector makes an angle of 35° with the positive x axis. What is the magnitude of the velocity of the 6. 0-kg mass after the collision?
The magnitude of the velocity of the 6.0 kg mass after the collision is approximately 1.7 m/s.
We can solve this problem using conservation of momentum and conservation of kinetic energy. Conservation of momentum states that the total momentum of a system is conserved if there are no external forces acting on it. In this case, the system is the two masses.
Let p1 and p2 be the initial momenta of the 3.0 kg and 6.0 kg masses, respectively, and p1' and p2' be their final momenta after the collision. Since the 6.0 kg mass is initially at rest, we have:
p1 = m1v1 = (3.0 kg)(10 m/s) = 30 kg·m/s
p2 = m2v2 = (6.0 kg)(0 m/s) = 0 kg·m/s
After the collision, the 3.0 kg mass moves at an angle of 35° with a speed of 8.0 m/s. We can break its velocity into x- and y-components:
vx = v1' cos(35°) = 8.0 m/s cos(35°) ≈ 6.6 m/s
vy = v1' sin(35°) = 8.0 m/s sin(35°) ≈ 4.6 m/s
The total momentum of the system after the collision is:
p1' + p2' = m1v1' + m2v2'
We can use conservation of momentum to say that p1 + p2 = p1' + p2', so:
p1' + p2' = 30 kg·m/s
Substituting in the known values, we have:
(3.0 kg)(6.6 m/s) + (6.0 kg)v2' = 30 kg·m/s
Solving for v2', we get:
v2' = (30 kg·m/s - 19.8 kg·m/s) / 6.0 kg ≈ 1.7 m/s
To know more about velocity, here
https://brainly.com/question/17127206
#SPJ4
Power supplies are rated for efficiency based on. drawn to supply sufficient power to the PC. a. volts b. watts c. amperes d. ohms. Study These Flashcards.
B. Power supplies are rated for efficiency based on watts. The efficiency of a power supply is determined by the ratio of its output power (in watts) to its input power (also in watts).
The lesser the effectiveness, the lower power is wasted as heat and the lesser the power given to the computer's factors. In addition to effectiveness, power inventories are rated for maximum affair power, which is generally expressed in watts. This standing represents the loftiest quantum of power that the power force can deliver to the computer's factors.
Other conditions, similar as voltage and amperage conditions for their different affair connections, may be assigned to power inventories. The maximum voltage and current that the power force can produce on each connection are indicated by these conditions. Ohms, on the other hand, are a resistance unit that's infrequently used to grade power force.
Learn more about power at
https://brainly.com/question/30562600
#SPJ4
Potable water is ____.
A. also known as industrial wastewater
B. also known as irrigation water
C. also known as sewage
D. also known as groundwater
E. fit for drinking
Potable water is fit for drinking. Option E
What is portable water?Potable water is water that is safe for human consumption and considered fit for drinking. It is free from harmful bacteria, viruses, chemicals, and other contaminants that can cause health problems.
Potable water can come from different sources such as groundwater, surface water, or treated wastewater, and it is typically treated and disinfected to ensure its safety before being distributed to consumers.
Portable water isn't known as industrial wastewater, irrigation water, groundwater and sewage.
Find more exercises on portable water;
https://brainly.com/question/2570757
#SPJ1
A book sitting on a desk with the surface area of the cover of .05 m^2. The atmospheric pressure is 100kPa. What is the downward force of the atmosphere on the book?
The downward force of the atmosphere on the book is equal to the pressure of the atmosphere multiplied by the surface area of the book's cover and it is calculated to be 5 N.
What is atmospheric pressure?Atmospheric pressure is the pressure exerted by the weight of the Earth's atmosphere on objects on or near the surface of the Earth. It is caused by the gravitational attraction of the Earth on the gases in the atmosphere. The atmospheric pressure varies with altitude, temperature, and weather conditions, and is typically measured in units of pressure such as pascals (Pa) or kilopascals (kPa).
Force = Pressure x Area
Where:
Pressure = 100 kPa (given)
Area = 0.05 m² (given)
Substituting the given values, we get:
Force = 100 kPa x 0.05 m²
Force = 5 N
Therefore, the downward force of the atmosphere on the book is 5 N.
To know more about atmospheric pressure, visit:
https://brainly.com/question/30166820
#SPJ1
if the wavelength of a wave in a particular medium is tripled, what will happen to the frequency of the wave?
Answer:
V = λ * ν speed of wave in medium
We know the speed of a particular wave in a medium is constant.
ν = V / λ
If λ is increased by 3 then the frequency ν will be reduced by a factor of three to keep the speed constant.
ν' = ν / 3
The majority of Venus's surface is:
A. volcanic plains with flowing lava.
B large, flat mesas with tiny valleys.
C. thick, soupy clouds of hydrogen.
D. frozen dunes of dust and sand.
Answer:
C.
Explanation:
When Venus surface get bit cold when weather hits the planet gets soupy clouds and etc.
what is the weight of a cubic meter of cork? could you lift it? (use 400 kg/m^3 for the density of cork.)
To lift this weight, you would need a force greater than or equal to 3,920 N (assuming you are lifting it vertically).
weight = [tex]1 m^3 \times 400 kg/m^3 \times9.8 m/s^2[/tex]
weight = 3,920 N
Force is a physical quantity that describes the interaction between objects or systems. The SI unit of force is the Newton (N), which is defined as the amount of force required to accelerate a one kilogram mass at a rate of one meter per second squared.
Force is also responsible for deformations in solid objects, such as stretching or compressing a spring. Nuclear forces are responsible for the interactions between subatomic particles, and frictional forces are the forces that resist motion when two surfaces come into contact. Gravitational force is the force that pulls objects towards each other due to their masses. Electromagnetic force is responsible for the interactions between charged particles, such as in electricity or magnetism.
To learn more about Force visit here:
brainly.com/question/24115409
#SPJ4
is it ok to keep my ac running and just stop the car's engine to save gas and keep cool while waiting for my husband?
It is not recommended to keep the AC running while the engine is off, as this can drain the car battery and may lead to mechanical issues in the long run. It is better to turn off the AC and open the windows or step out of the car to cool off while waiting for your husband.
Idling the engine for extended periods of time can also waste gas and contribute to air pollution. When you stop your car's engine, the air conditioning (AC) system will also stop working, as it requires the engine to be running to function properly. To save gas and keep cool while waiting for your husband, you may consider:
1. Turn off your car's engine to save gas.
2. Open the windows slightly to allow for airflow.
3. Use a portable battery-operated fan to keep yourself cool.
4. Park your car in a shaded area, if possible, to reduce heat buildup inside the vehicle.
5. Wear light, breathable clothing to stay comfortable in warmer temperatures.
Remember that running the AC without the engine is not possible, so it's essential to find alternative ways to stay cool while conserving fuel.
More on car engine: https://brainly.com/question/29980491
#SPJ11
019 (part 1 of 2) 10.0 points
A Carnot engine has a power output of
197 kW. The engine operates between two
reservoirs at 20◦C and 425◦C.
How much thermal energy is absorbed each
hour?
Answer in units of J.
020 (part 2 of 2) 10.0 points
How much thermal energy is lost per hour?
Answer in units of J.
Thermal energy is absorbed each hour is 13.53 x 10¹² J and thermal energy lost per hour is 7.092 x 10¹² J.
What is the Carnot engine's operating principle?a technique of isothermal gas expansion that is reversible. In this process, the ideal gas in the system receives amount heat from a heat source at a high temperature Thigh, expands and does work on surroundings. a technique of adiabatic gas expansion that is reversible. The system is thermally insulated throughout this process.
Temp_cold = 20°C + 273.15 = 293.15 K
Temp_hot = 425°C + 273.15 = 698.15 K
efficiency = 1 - (Temp_cold / Temp_hot)
= (698.15 K * 293.15 K) / (698.15 K)² - (293.15 K)²
efficiency = 0.524 or 52.4%
thermal energy absorbed/ hour = power output / efficiency
= 197 kW / 0.524
= 375.95 MJ/h x 3.6 x 10⁶ J/kWh = 13.53 x 10¹² J
thermal energy is lost per hour
W = power output x time = 197 kW x 1 h = 197 kWh
W = 197 kWh x 3.6 x 10⁶ J/kWh = 7.092 x 10¹²1J
Since the engine is running in a cycle, the system's internal energy is equal to zero, hence U = 0.
Q = ΔU + W
hence, thermal energy lost per hour = Q = W = 7.092 x 10^11 J
To know more about thermal energy visit:-
https://brainly.com/question/27359499
#SPJ1
How does energy in the food chain flow to an omnivore such as a fox?
A) The fox is a plant eater and receives energy directly from plants.
B) The fox receives energy directly from the sun and the plants it eats.
C) When the fox eats an animal that eats plants, it receives energy directly from the sun.
D) When the fox eats an animal that eats plants, it receives energy indirectly from the sun.
The correct answer is option D) When the fox eats an animal that eats plants, it receives energy indirectly from the sun.
How does energy flow in a food chain?Energy in a food chain flows from the sun, to the producers (plants), to the primary consumers (herbivores), to the secondary consumers (carnivores), and so on. Omnivores, such as foxes, consume both plants and animals, but they typically obtain more of their energy from consuming other animals.
When a fox eats an animal that eats plants, it is receiving energy indirectly from the sun. The plants that the prey animal consumed converted the energy from the sun into organic molecules through the process of photosynthesis. The prey animal then consumed those plants and converted the organic molecules into its own tissues. When the fox eats the prey animal, it is obtaining the energy stored in the prey's tissues.
Learn more about the food chain here:
https://brainly.com/question/7564953
#SPJ1
a drawing, provided by the manufacturer, that details permitted interconnections between the intrinsically safe and associated apparatus or between the nonincendive field wiring apparatus or associated nonincendive field wiring apparatus is called a
The drawing provided by the manufacturer, which details the permitted interconnections between intrinsically safe and associated apparatus or between nonincendive field wiring apparatus or associated nonincendive field wiring apparatus, is called a wiring diagram.
A wiring diagram typically includes detailed information about the wiring connections between components, as well as any necessary safety measures such as grounding or shielding. It may also include information about the voltage, current, and power requirements of the system, as well as any limitations or restrictions on the use of particular components or configurations.
This diagram is a critical part of the installation and maintenance process for intrinsically safe and nonincendive electrical systems, as it helps ensure that the correct connections are made and that the system operates safely and effectively.
To learn more about diagram follow the link:
https://brainly.com/question/11729094
#SPJ4
The complete question is:
A drawing, provided by the manufacturer, that details permitted interconnections between the intrinsically safe and associated apparatus or between the nonincendive field wiring apparatus or associated nonincendive field wiring apparatus is called a ______________