The mass of water to be 59.82 kg, the final volume to be 76.42 L, and the total internal energy change to be 17610 kJ. The process is shown on a P-v diagram, indicating that it is not reversible.
Initial volume of liquid water V1 = 60 L, Pressure P1 = 200 k, PaInitial temperature T1 = 40°C = 313.15 K
Final temperature T2 = 125°C = 398.15 K. Now, we can find the mass of water using the relation as below;m = V1ρ, Where,
ρ is the density of water at the given temperature.
ρ = 997 kg/m³ (at 40°C). Mass of water,m = 60 L x 1 m³/1000 L x 997 kg/m³ = 59.82 kg. Hence, the mass of water is 59.82 kg.
To find final volume, we can use the relationship as below; V2 = V1 (T2 / T1), Where
V2 is the final volume.
Substituting the values, we get; V2 = 60 L x (398.15 K / 313.15 K) = 76.42 L. Hence, the final volume is 76.42 L.
Internal energy change ΔU is given by the relation; ΔU = mCΔT, Where,
C is the specific heat capacity of water at the given temperature.
C = 4.18 kJ/kg-K for water at 40°C and 1 atm pressure. Substituting the values, we get; ΔU = 59.82 kg x 4.18 kJ/kg-K x (125 - 40)°C = 17610 kJ.
Hence, the total internal energy change is 17610 kJ.
Then, heat is transferred at constant pressure and the temperature increases to 125°C. This leads to the increase in volume to V2 = 76.42 L. The final state is represented by point B. The process follows the constant pressure line as shown. The state points A and B are not on the saturated liquid-vapor curve, and hence the process is not a reversible one.
Learn more about energy change: brainly.com/question/18345151
#SPJ11
The dry products of combustion have the following molar percentages: CO 2.7% 025.3% H20.9% CO2 16.3% N2 74.8% Find, for these conditions: (a) mixture gravimetric analysis; (b) mixture molecular weight, lbm/lbmole; and (c) mixture specific gas constant R, ft lbf/Ibm °R.
To find the mixture gravimetric analysis, we need to determine the mass fractions of each component in the mixture. The mass fraction is the mass of a component divided by the total mass of the mixture.
Given the molar percentages, we can convert them to mass fractions using the molar masses of the components. The molar masses are as follows:
CO: 28.01 g/mol
O2: 32.00 g/mol
H2O: 18.02 g/mol
CO2: 44.01 g/mol
N2: 28.01 g/mol
(a) Mixture Gravimetric Analysis:
The mass fraction of each component is calculated by multiplying its molar percentage by its molar mass and dividing by the sum of all the mass fractions.
Mass fraction of CO: (0.027 * 28.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of O2: (0.253 * 32.00) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of H2O: (0.009 * 18.02) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of CO2: (0.163 * 44.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
Mass fraction of N2: (0.748 * 28.01) / (0.027 * 28.01 + 0.253 * 32.00 + 0.009 * 18.02 + 0.163 * 44.01 + 0.748 * 28.01)
(b) Mixture Molecular Weight:
The mixture molecular weight is the sum of the mass fractions multiplied by the molar masses of each component.
Mixture molecular weight = (Mass fraction of CO * Molar mass of CO) + (Mass fraction of O2 * Molar mass of O2) + (Mass fraction of H2O * Molar mass of H2O) + (Mass fraction of CO2 * Molar mass of CO2) + (Mass fraction of N2 * Molar mass of N2)
(c) Mixture Specific Gas Constant:
The mixture specific gas constant can be calculated using the ideal gas law equation:
R = R_universal / Mixture molecular weight
where R_universal is the universal gas constant.
Now you can substitute the values and calculate the desired quantities.
To know more about mixture gravimetric analysis, click here:
https://brainly.com/question/30864235
#SPJ11
Q4. A solid shaft of diameter 50mm and length of 300mm is subjected to an axial load P = 200 kN and a torque T = 1.5 kN-m. (a) Determine the maximum normal stress and the maximum shear stress. (b) Repeat part (a) but for a hollow shaft with a wall thickness of 5 mm.
Part (a)The normal stress and the shear stress developed in a solid shaft when subjected to an axial load and torque can be calculated by the following equations.
Normal Stress,[tex]σ =(P/A)+((Mz×r)/Iz)[/tex]Where,[tex]P = 200kNA
= πd²/4 = π×(50)²/4
= 1963.4954 mm²Mz[/tex]
= T = 1.5 kN-mr = d/2 = 50/2 = 25 m mIz = πd⁴/64 = π×(50)⁴/64[/tex]
[tex]= 24414.2656 mm⁴σ[/tex]
[tex]= (200 × 10³ N) / (1963.4954 mm²) + ((1.5 × 10³ N-mm) × (25 mm))/(24414.2656 mm⁴)σ[/tex]Shear Stress.
[tex][tex]J = πd⁴/32 = π×50⁴/32[/tex]
[tex]= 122071.6404 mm⁴τ[/tex]
[tex]= (1.5 × 10³ N-mm) × (25 mm)/(122071.6404 mm⁴)τ[/tex]
[tex]= 0.03 MPa[/tex] Part (b)For a hollow shaft with a wall thickness of 5mm, the outer diameter, d₂ = 50mm and the inner diameter.
To know more about developed visit:
https://brainly.com/question/31944410
#SPJ11
The following information was provided by the responsible engineer of that power plant regarding the steam cycle part: mi, tonnes per hour of superheated steam enters the high-pressure turbine at T₁ °C and P, Bar, and is discharged isentropically until the pressure reaches P₂ Bar. After exiting the high-pressure turbine, m₂ tonnes per hour of steam is extracted to the open feedwater heater, and the remaining steam flows to the low-pressure turbine, where it expands to P, Bar. At the condenser, the steam is totally condensed. The temperature at the condenser's outflow is the same as the saturation temperature at the same pressure. The liquid is compressed to P₂ Bar after passing through the condenser and then allowed to flow through the mixing preheater (a heat exchanger with efficiency n)where it is completely condensed. The preheated feed water will be fed into the heat exchanger through a second feed pump, where it will be heated and superheated to a temperature of T₁°C. In the winter, the overall process heating demand is assumed to be Q MW while this power plant's electricity demand is # MW. 5. Schematic of the power plant: An excellent and high-quality schematic must be presented, with all necessary and appropriate information pertinent to the analysis' content. Any diagramming and vector graphics application, such as Microsoft Visio, can be used. (Maximum 1 page).
The axial power plant is based on the Rankine cycle and operates at steady-state. A schematic diagram of a steam cycle power plant has been provided.
Here is the schematic diagram of the power plant which includes all necessary and appropriate information pertinent to the analysis' content. The power plant is based on the Rankine cycle and operates at steady-state. A schematic diagram of a steam cycle power plant has been provided. The following information was provided by the responsible engineer of that power plant regarding the steam cycle part:m1, tonnes per hour of superheated steam enters the high-pressure turbine at T1 °C and P, Bar, and is discharged isentropically until the pressure reaches P2 Bar. After exiting the high-pressure turbine, m2 tonnes per hour of steam is extracted to the open feedwater heater, and the remaining steam flows to the low-pressure turbine, where it expands to P, Bar.
At the condenser, the steam is totally condensed. The temperature at the condenser's outflow is the same as the saturation temperature at the same pressure. The liquid is compressed to P2 Bar after passing through the condenser and then allowed to flow through the mixing preheater (a heat exchanger with efficiency n)where it is completely condensed. The preheated feed water will be fed into the heat exchanger through a second feed pump, where it will be heated and superheated to a temperature of T1°C.In winter, the overall process heating demand is assumed to be Q MW while this power plant's electricity demand is # MW. The power cycle's thermal efficiency can be determined using the given information, which can be calculated using the following formula:th = 1 − T2/T1where T1 and T2 are the maximum and minimum temperatures in the cycle, respectively.
To know more about axial visit
https://brainly.com/question/33140251
#SPJ11
Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10MPa and 500 ∘ C and is cooled in the condenser at a pressure of 20kPa.
a) determine the quality of steam at the turbine exit
b) determine the thermal efficiency of the cycle
c) determine the mass flow rate of the steam
a) The quality of steam at the turbine exit is x=0.875 or 87.5%.b) Thermal efficiency of the cycle is 38.2%.c) The mass flow rate of the steam is 657.6 kg/s.How to solve the given problem?Given parameters are,Steam enters the turbine at a pressure of 10 MPa and a temperature of 500°CPressure at the condenser = 20 kPaThe Rankine cycle consists of the following four processes:1-2 Isentropic compression in a pump2-3 Constant pressure heat addition in a boiler3-4 Isentropic expansion in a turbine4-1 Constant pressure heat rejection in a condenserTemperature-Entropy (T-S) diagram of a Rankine cycleThe formula used to calculate the quality of steam isx = [h - hf] / [hg - hf]
where, x = quality of steamh = specific enthalpyhf = specific enthalpy of saturated liquid at given pressure and temperaturehg = specific enthalpy of saturated vapor at given pressure and temperaturea) Determination of the quality of steam at the turbine exitAt the turbine inlet,Pressure (P1) = 10 MPaTemperature (T1) = 500°CEnthalpy at 10 MPa and 500°C, h1 = 3587.8 kJ/kgThe turbine's exit is connected to a condenser that operates at 20 kPa. Since the condenser is a constant pressure heat exchanger, the quality of steam at the turbine exit is determined by finding the enthalpy at 20 kPa corresponding to the specific entropy at the turbine exit pressure (P2 = 20 kPa) and using it to calculate the steam quality.
At the turbine exit,Pressure (P2) = 20 kPaQuality of steam at the turbine exit, x2 = ?To calculate the steam quality, determine the specific entropy of the steam at the turbine exit using the given pressure of 20 kPa. The specific entropy value corresponding to this pressure and enthalpy (h2s) is 0.6499 kJ/kg-K.Enthalpy at 20 kPa and 0.6499 kJ/kg-K, h2f = 191.81 kJ/kgEnthalpy at 20 kPa and dryness fraction 1, h2g = 2401.3 kJ/kgNow use the formula of steam quality,x2 = (h2 - h2f)/(h2g - h2f)x2 = (1011.9 - 191.81)/(2401.3 - 191.81)x2 = 0.875 or 87.5%The quality of steam at the turbine exit is x=0.875 or 87.5%.b) Determination of the thermal efficiency of the cycleTo calculate the thermal efficiency of the cycle, use the following formula.
To know more about efficiency visit:-
https://brainly.com/question/30861596
#SPJ11
roblem 6 Using a clear sketch show the heat affected zone of a weld. What is its significance? Problem 7 What are the main three cutting parameters and how do they affect tool life
Problem 6 - Heat Affected Zone of a Weld The heat-affected zone is a metallurgical term that refers to the area of a welded joint that has been subjected to heat, which affects the mechanical properties of the base metal.
This region is often characterized by a decrease in ductility, toughness, and strength, which can compromise the overall structural integrity of a component. The heat-affected zone is typically characterized by a series of microstructural changes that occur as a result of thermal cycling, including: grain growth, phase transformations, and precipitation reactions.
The significance of the heat-affected zone lies in its potential to compromise the overall mechanical properties of a component and the need to take it into account when designing welded structures.
Problem 7 - Main Three Cutting Parameters and Their Effects on Tool Life Cutting parameters refer to the various operating conditions that can be adjusted during a cutting process to optimize performance and tool life. The main three cutting parameters are speed, feed, and depth of cut.
Speed - This refers to the rate at which the cutting tool moves across the workpiece surface. Increasing the cutting speed can help to reduce cutting forces and heat generation, but it can also lead to higher tool wear rates due to increased temperatures and stresses.
Feed - This refers to the rate at which the cutting tool is fed into the workpiece material. Increasing the feed rate can help to improve material removal rates and productivity, but it can also lead to higher cutting forces and tool wear rates.
Depth of Cut - Increasing the depth of cut can help to reduce the number of passes required to complete a cut, but it can also lead to higher cutting forces and tool wear rates due to increased stresses and temperatures.
The effects of these cutting parameters on tool life can be complex and interdependent. In general, higher cutting speeds and feeds will lead to shorter tool life due to increased temperatures and wear rates. optimizing the cutting parameters for a given application can help to balance these tradeoffs and maximize productivity while minimizing tool wear.
To know more about metallurgical visit:-
https://brainly.com/question/32005998
#SPJ11
IF an 85% efficient alternator operating at 1800RPM were putting
out 100kW of power how much torque would need tro be delivered by
the prime mover?
To determine the amount of torque that the prime mover would need to deliver to operate an 85% efficient alternator operating at 1800 RPM and putting out 100 kW of power, the following equation is used:Power = (2π × RPM × Torque) / 60 × 1000 kW = (2π × 1800 RPM × Torque) / 60 × 1000
Rearranging the equation to solve for torque:Torque = (Power × 60 × 1000) / (2π × RPM)Plugging in the given values:Torque = (100 kW × 60 × 1000) / (2π × 1800 RPM)≈ 318.3 Nm
Therefore, the prime mover would need to deliver about 318.3 Nm of torque to operate an 85% efficient alternator operating at 1800 RPM and putting out 100 kW of power. This can also be written as 235.2 lb-ft.
To know more about torque visiṭ:
https://brainly.com/question/30338175
#SPJ11
A polymeric cylinder initially exerts a stress with a magnitude (absolute value) of 1.437 MPa when compressed. If the tensile modulus and viscosity of this polymer are 16.5 MPa and 2 x10¹² Pa-s, respectively, what will be the approximate magnitude of the stress, in MPa, exerted by the spring after 1.8 day(s)? Answer Format: X.X Unit: MPa
The stress, in MPa, exerted by the spring after 1.8 days is approximately 0.176 MP
a. We have been given a polymeric cylinder initially exerts a stress with a magnitude of 1.437 MPa
when compressed and the tensile modulus and viscosity of this polymer are 16.5 MPa and 2 × 10¹² Pa-s respectively.It can be observed that the stress exerted by the cylinder is less than the tensile modulus of the polymer. Therefore, the cylinder behaves elastically.
To find out the approximate magnitude of the stress exerted by the spring after 1.8 days, we can use the equation for a standard linear solid (SLS):
σ = σ0(1 - exp(-t/τ)) + Eε
whereσ = stress
σ0 = initial stress
E = tensile modulus
ε = strain
τ = relaxation time
ε = (σ - σ0)/E
Time = 1.8 days = 1.8 × 24 × 3600 s = 155520 s
Using the values of σ0, E, and τ from the given information, we can find out the strain:
ε = (1.437 - 0)/16.5 × 10⁶ε = 8.71 × 10⁻⁸
From the equation for SLS, we can write:
σ = σ0(1 - exp(-t/τ)) + Eεσ
= 1.437(1 - exp(-155520/2 × 10¹²)) + 16.5 × 10⁶ × 8.71 × 10⁻⁸σ
= 1.437(1 - 0.99999999961) + 1.437 × 10⁻⁴σ ≈ 0.176 MPa
Thus, the stress exerted by the spring after 1.8 days is approximately 0.176 MPa.
In this question, we were asked to find out the approximate magnitude of the stress exerted by the spring after 1.8 days. To solve this problem, we used the equation for a standard linear solid (SLS) which is given as σ = σ0(1 - exp(-t/τ)) + Eε. Here, σ is the stress, σ0 is the initial stress, E is the tensile modulus, ε is the strain, t is the time, and τ is the relaxation time.Using the given values, we first found out the strain. We were given the initial stress and the tensile modulus of the polymer. Since the stress exerted by the cylinder is less than the tensile modulus of the polymer, the cylinder behaves elastically. Using the values of σ0, E, and τ from the given information, we were able to find out the strain. Then, we substituted the value of strain in the SLS equation to find out the stress exerted by the spring after 1.8 days. The answer we obtained was approximately 0.176 MPa.
Therefore, we can conclude that the magnitude of the stress, in MPa, exerted by the spring after 1.8 days is approximately 0.176 MPa.
Learn more about tensile modulus here:
brainly.com/question/32775852
#SPJ11
The absorption test is primarily used to evaluate the: 1)Flow ability 2)Durability 3)Strength
The absorption test is primarily used to evaluate the flow ability of a material.
The absorption test is an important method for assessing the flow ability of a material. It measures the amount of liquid that a material can absorb and retain. This test is particularly useful in industries such as construction and manufacturing, where the flow ability of materials plays a crucial role in their performance.
Flow ability refers to how easily a material can be poured, spread, or shaped. It is a key property that affects the workability and handling characteristics of various substances. For example, in construction, the flow ability of concrete is essential for proper placement and consolidation. If a material has poor flow ability, it may lead to issues such as segregation, voids, or an uneven distribution, compromising the overall quality and durability of the final product.
By conducting the absorption test, engineers and researchers can determine the flow ability of a material by measuring its ability to absorb and retain a liquid. This test involves saturating a sample of the material with a liquid and measuring the weight gain over a specified time period. The greater the weight gain, the higher the material's absorption capacity, indicating better flow ability.
Learn more about absorption
brainly.com/question/30697449
#SPJ11
A block is pressed 0.1 m against a spring(k = 500 N/m), and then released. The kinetic coefficient of friction between the block and the horizontal surface is 0.6. Determine mass of block, if it travels 4 m before stopping. Use work and energy method.
If the block travels 4 m before stopping, then the mass of the block is 0.085 kg.
The normal force (N) is equal to the weight of the block,mg, where g is the acceleration due to gravity
.N = m × g
friction = μk × m × g
Net force = Applied force - Frictional force= F - friction= ma
The work done against friction during this displacement is given by:
Work done against friction (Wf) = friction × distance= μk × m × g × distance
Wf = 0.6 × m × 9.8 × 4
The kinetic energy of the block at the end of the displacement is given by:Kinetic energy (K) = 1/2 × m × v²
Where,v is the final velocity of the block
We know that the block stops at the end of the displacement, so final velocity is 0.
Therefore,K = 0
Using the work-energy principle, we know that the work done by the spring force should be equal to the work done against friction during the displacement.
That is,Work done by spring force (Ws) = Work done against friction (Wf)
Ws = 2.5 J = Wf
0.5 × k × x² = μk × m × g × distance
0.5 × 500 × 0.1² = 0.6 × m × 9.8 × 40.05 = 5.88m
Simplifying, we get,m = 0.085 kg
Learn more about the work done at
https://brainly.com/question/14889813
#SPJ11
Describe different kinds of flow metres in detail.
Flow meters are instruments used to measure the volume or mass of a liquid, gas, or steam passing through pipelines. Flow meters are used in industrial, commercial, and residential applications. Flow meters can be classified into several types based on their measuring principle.
Differential Pressure Flow Meter: This is the most common type of flow meter used in industrial applications. It works by creating a pressure difference between two points in a pipe. The pressure difference is then used to calculate the flow rate. Differential pressure flow meters include orifice meters, venturi meters, and flow nozzles.
Positive Displacement Flow Meter: This type of flow meter works by measuring the volume of fluid that passes through a pipe. The flow rate is determined by measuring the amount of fluid that fills a chamber of known volume. Positive displacement flow meters include nutating disk meters, oval gear meters, and piston meters.
flow meters are essential devices that help to measure the volume or mass of fluid flowing through pipelines. They can be classified into different types based on their measuring principle. Each type of flow meter has its advantages and limitations.
To know more about residential applications visit:-
https://brainly.com/question/31607700
#SPJ11
In a small hydro power station , electricity generation is highly related to the performance of a turbine . Thus , reliability and quality are very crucial . As an example , reliability function , R ( t ) of a turbine represented by the following equation : R ( 1 ) = ( 1-1 / t . ) ² 0≤1≤to Where , to is the maximum life of the blade 1 . Prove that the blades are experiencing wear out . ii . Compute the Mean Time to Failure ( MTTF ) as a function of the maximum life . iii . If the maximum life is 2000 operating hours , determine the design life for a reliability of 0.90 ?
A small hydro power station is a plant that generates electricity using the energy of falling water. Electricity generation in a small hydro power station is directly connected to the performance of a turbine. As a result, the reliability and quality of the system are critical. In this case, the reliability function, R(t), of a turbine is determined by the equation R(1) = (1 - 1/t)^2 0 ≤ 1 ≤ to where to represents the maximum life of blade 1.
Proof that the blades are experiencing wear out: The reliability function given as R(1) = (1 - 1/t)^2 0 ≤ 1 ≤ to can be used to prove that the blades are experiencing wear out. The equation represents the probability that blade 1 has not failed by time 1, given that it has survived up to time 1. The reliability function is a decreasing function of time. As a result, as time passes, the probability of the blade failing grows. This is a sign that the blade is wearing out, and its lifespan is limited.
Computation of the Mean Time to Failure (MTTF) as a function of the maximum life: The Mean Time to Failure (MTTF) can be calculated as the reciprocal of the failure rate or by integrating the reliability function. Since the failure rate is constant, MTTF = 1/λ. λ = failure rate = (1 - R(t)) / t. 0 ≤ t ≤ to. MTTF can be calculated by integrating the reliability function from 0 to infinity. The MTTF can be calculated as follows:
MTTF = ∫ 1 to [1 / (1 - 1/t)^2] dt. This can be solved using substitution or integration by parts.
Determination of the design life for a reliability of 0.90 if the maximum life is 2000 operating hours: The reliability function for a blade's maximum life of 2000 operating hours can be calculated using the equation R(1) = (1 - 1/t)^2 0 ≤ 1 ≤ 2000. R(1) = (1 - 1/2000)^2 = 0.99995. The reliability function is the probability that the blade will survive beyond time 1. The reliability function is 0.90 when the blade's design life is reached. As a result, the value of t that satisfies R(t) = 0.90 should be found. We must determine the value of t in the equation R(t) = (1 - 1/t)^2 = 0.90. The t value can be calculated as t = 91.8 hours, which means the design life of the blade is 91.8 hours.
Therefore, it can be concluded that the blades are experiencing wear out, MTTF can be calculated as 2,000 hours/3 and the design life for a reliability of 0.90 with a maximum life of 2,000 operating hours is 91.8 hours.
To know more about hydro power station refer to:
https://brainly.com/question/31149924
#SPJ11
The velocity profile for a fluid flow over a flat plate is given as u/U=(3y/58) where u is velocity at a distance of "y" from the plate and u=U at y=o, where ō is the boundary layer thickness. Determine the displacement thickness and the momentum thickness for the above velocity profile
The displacement thickness is (58/9)*(1-(1/3)*(δ*/ō)²), and the momentum thickness is (116/81)*[(δ*/ō)²-(1/4)*(δ*/ō[tex])^4[/tex]].
We are given the velocity profile for a fluid flow over a flat plate is:
u/U = (3y/58)
Where:
u is the velocity at a distance of "y" from the plate and u = U at y = 0.
U is the free-stream velocity.
ō is the boundary layer thickness.
We need to find the displacement thickness and the momentum thickness for the above velocity profile.
Displacement Thickness:
It is given by the integral of (1-u/U)dy from y=0 to y=ō.
Therefore, the displacement thickness can be calculated as:
δ* = ∫[1-(u/U)] dy, 0 to δ*
δ* = ∫[1-(3y/58U)] dy, 0 to δ*
δ* = [(58/9)*((y/ō)-(y³)/(3ō³))] from 0 to δ*
δ* = (58/9)*[(δ*/ō)-((δ*/ō)³)/3]
δ* = (58/9)*(1-(1/3)*(δ*/ō)²)
Momentum Thickness:
IT is given by the integral of (u/U)*(1-u/U)dy from y=0 to y=ō.
Therefore, the momentum thickness can be written as;
θ = ∫[(u/U)*(1-(u/U))] dy, 0 to δ*
θ = ∫[(3y/58U)*(1-(3y/58U))] dy, 0 to δ*
θ = [(116/81)*((y/ō)²)-((y/ō[tex])^4[/tex])/4] from 0 to δ*
θ = (116/81)*[(δ*/ō)²-(1/4)*(δ*/ō[tex])^4[/tex]]
Learn more about Thickness here;
https://brainly.com/question/28222770
#SPJ4
Consider ammonium throttling at constant enthalpy from 2Mpa(a)(saturated liquid) to 0,1Mpa(a)and Find initial and end temperature by ammonium chart. Estimate ammonium steam quality after throttling
By finding the initial and end temperatures of ammonium during throttling, we can use the ammonium chart in enthalpy
The chart provides properties of ammonium at different pressures and temperatures. Here are the steps to estimate the temperatures:
1. Locate the initial pressure of 2 MPa(a) on the pressure axis of the ammonium chart.
2. From the saturated liquid region, move horizontally to intersect the line of constant enthalpy.
3. Read the initial temperature at this intersection point. This will give the initial temperature of ammonium before throttling.
4. Locate the final pressure of 0.1 MPa(a) on the pressure axis.
5. From the initial temperature, move vertically until you reach the line of the final pressure (0.1 MPa(a)).
6. Read the temperature at this intersection point. This will give the final temperature of ammonium after throttling.
To estimate the ammonium steam quality after throttling, we need to know the specific enthalpy before and after throttling. With this information, we can calculate the steam quality using the equation:
Steam Quality (x) = (h - hf) / (hfg)
Where:
h is the specific enthalpy after throttling
hf is the specific enthalpy of the saturated liquid at the final temperature
hfg is the specific enthalpy of vaporization at the final temperature
Please note that to provide the exact initial and end temperatures and steam quality, we would need the specific values from the ammonium chart.
To know more about enthalpy visit:
brainly.com/question/30464179
SPJ11
please answer the question with the following steps:
1- basic assumptions
2- driven equations
3- manual solution
4- reaults and analysis
Refrigerant-134a enters the compressor of a refrigeration system as saturated vapor at 0.14 MPa, and leaves as superheated vapor at 0.8 MPa and 60°C at a rate of 0.06 kg/s. Determine the rates of energy transfers by mass into and out of the compressor. Assume the kinetic and potential energies to be negligible
The rates of energy transfers can be determined by calculating the difference in specific enthalpy between the compressor inlet and outlet states using thermodynamic property tables.
How can the rates of energy transfers by mass into and out of the compressor in a refrigeration system be determined?1. Basic Assumptions:
The refrigerant-134a behaves as an ideal gas throughout the process.Kinetic and potential energies are negligible.The compressor operates under steady-state conditions.2. Driven Equations:
The energy transfer into the compressor can be determined using the equation:Qin = h2 - h1
3. Manual Solution:
Look up the specific enthalpy values of refrigerant-134a at the given states using a thermodynamic property table.Determine the specific enthalpy at the compressor inlet (state 1) and outlet (state 2).Calculate the energy transfer rate by subtracting h1 from h2: Qin = h2 - h1.4. Results and Analysis:
The calculated value of Qin represents the rate of energy transfer by mass into the compressor.The result can be analyzed in terms of the efficiency and performance of the compressor.Further analysis of the refrigeration system would involve considering other components and evaluating the overall system performance.Learn more about energy transfers
brainly.com/question/18649915
#SPJ11
Use a five-variable Karnaugh map to find the minimized SOP expression for the following logic function: F(A,B,C,D,E) = Σm(4,5,6,7,9,11,13,15,16,18,27,28,31)
A five-variable Karnaugh map is a 5-dimensional table that is used to simplify boolean expressions. It is made up of a set of 32 cells (2^5) that are arranged in such a way that every cell is adjacent to its four neighboring cells.
The cells in the Karnaugh map are labeled with binary numbers that correspond to the binary values of the variables that are used in the boolean expression.
In order to find the minimized SOP expression for the given logic function F(A,B,C,D,E) = Σm(4,5,6,7,9,11,13,15,16,18,27,28,31), we can follow these steps:
Step 1: Draw the 5-variable Karnaugh map
We can draw the 5-variable Karnaugh map by labeling the cells with their binary as shown below:
ABCDE
00000
00001
00011
00010
00110
00111
00101
00100
01100
01101
01111
01110
01010
01011
01001
01000
11000
11001
11011
11010
11110
11111
11101
11100
10100
10101
10111
10110
10010
10011
10001
10000
Step 2: Group the cells that contain a 1
We can group the cells that contain a 1 in order to simplify the boolean expression. We can group the cells in pairs, quads, or octets as long as the cells that are grouped together are adjacent to each other. We can group the cells as shown below:
ABCDE
00000
00001
00011
00010
00110
00111
00101
00100
01100
01101
01111
01110
01010
01011
01001
01000
11000
11001
11011
11010
11110
11111
11101
11100
10100
10101
10111
10110
10010
10011
10001
10000
We can group the cells as follows:
AB\ CD\ E AB\ CD E AB\ C\ DE AB\ C\ D\ E
00 01 11 10 00 01 11 10 00 01 11 10 00 01 11 10
m4 m5 m7 m6 m9 m11 m15 m13 m16 m18 m31 m28 m27 m7 m6 m4
Step 3: Write the minimized SOP expression
We can use the complement of a variable if it appears in a group of cells that contain a 0. We can write the minimized SOP expression as follows:
F(A,B,C,D,E) = AB'C' + AB'D'E' + A'C'D'E + A'C'D'E'
Therefore, the minimized SOP expression for the given logic function F(A,B,C,D,E) = Σm(4,5,6,7,9,11,13,15,16,18,27,28,31) is F(A,B,C,D,E) = AB'C' + AB'D'E' + A'C'D'E + A'C'D'E'.
To know more about expression visit :
https://brainly.com/question/28170201
#SPJ11
Which of the following statements is FALSE? (a) Second moment is smallest about the centroidal axis (b) Eccentric loading can cause the neutral axis to shift away from the centroid (c) First moment Q is zero about the centroidal axis (d) Higher moment corresponds to a higher radius of curvature
Second moment is smallest about the centroidal axis.Second moment of area, I, is the summation of the products of the elemental area and the square of their respective distances from a neutral axis.
The given options are; (a) Second moment is smallest about the centroidal axis (b) Eccentric loading can cause the neutral axis to shift away from the centroid (c) First moment Q is zero about the centroidal axis (d) Higher moment corresponds to a higher radius of curvature.
(a) Second moment is smallest about the centroidal axis. Second moment of area, I, is the summation of the products of the elemental area and the square of their respective distances from a neutral axis. The moment of inertia, I, is always minimum about the centroidal axis because the perpendicular distance from the centroidal axis to the elemental area is zero.
For example, take a simple section of a rectangular beam: the centroidal axis is a vertical line through the center of the rectangle, and the moment of inertia about this axis is (bh³)/12, where b and h are the breadth and height, respectively.
Learn more about Second moment visit:
brainly.com/question/2285117
#SPJ11
MCQ: Which one of the following statements is true about a dual-voltage capacitor-start motor?
A. The auxiliary-winding circuit operates at 115 volts on 115-volt and 230-volt circuits.
B. The main windings are identical to obtain the same starting torques on 115-volt and 230-volt circuits.
C. The direction of rotation is reversed by interchanging the leads of one main winding.
D. The main windings are connected in series for 115-volt operation.
2. An auxiliary phase winding is used in a single-phase fractional horsepower motor to
A. decrease flux density. B. decrease motor heating. C. reverse motor rotation. D. increase motor speed.
3. The device which responds to the heat developed within the motor is the
A. shading coil. B. short-circuiter. C. bimetallic protector. D. current-operated relay.
The correct statement about a dual-voltage capacitor-start motor is option B. The main windings are identical to obtain the same starting torques on 115-volt and 230-volt circuits.
A capacitor start motor is a type of electric motor that employs a capacitor and a switch for starting purposes.
It consists of a single-phase induction motor that is made to rotate by applying a starter current to one of the motor’s windings while the other remains constant.
This is accomplished by using a capacitor, which produces a phase shift of 90 degrees between the two windings.
2. The answer to the second question is option C. Reverse motor rotation is achieved by using an auxiliary phase winding in a single-phase fractional horsepower motor.
In order to start the motor, this auxiliary winding is used. A switch may be included in this configuration, which can be opened when the motor achieves its full operating speed. This winding will keep the motor running in the right direction.
3. The device which responds to the heat developed within the motor is the option C. A bimetallic protector responds to the heat produced inside the motor.
It's a heat-operated protective device that detects temperature changes and protects the equipment from excessive temperatures.
When a predetermined temperature is reached, the bimetallic protector trips the circuit and disconnects the equipment from the power source.
To know more about capacitor visit:
https://brainly.com/question/31627158
#SPJ11
Question: Prove the receiving signal fulfills Rayleigh distribution under a Non-Light of sight situation. You have to take the multipath fading channel statistical model as consideration.
(Note: handwritten must be clear please! handwritten must be clear please!)
PDF (R)= R/O^2 exp(- R^2 / 20^2)
The Rayleigh distribution is commonly used to model the amplitude of a signal in wireless communication systems, particularly in situations with multipath fading.
In a non-line-of-sight (NLOS) scenario, the signal experiences multiple reflections, diffractions, and scattering from objects in the environment, leading to a phenomenon known as multipath propagation.
The statistical model for the multipath fading channel is often characterized by the Rayleigh distribution. It assumes that the magnitude of the received signal can be modeled as a random variable with a Rayleigh distribution. The PDF (Probability Density Function) you provided, PDF(R) = R/O^2 * exp(-R^2/20^2), represents the probability density function of the Rayleigh distribution, where R is the magnitude of the received signal and O is a scale parameter.
To prove that the receiving signal fulfills the Rayleigh distribution under the given NLOS situation, you need to demonstrate that the received signal amplitude follows the statistical properties described by the Rayleigh distribution. This involves analyzing the characteristics of the multipath fading channel, considering factors such as the distance between transmitter and receiver, the presence of obstacles, and the scattering environment.
Know more about Rayleigh distribution here:
https://brainly.com/question/30694232
#SPJ11
Flight path, is the path or the line along which the c.g. of the airplane moves. The tangent to this curve at a point gives the direction of flight velocity at that point on the flight path. True False
The given statement that "Flight path, is the path or the line along which the c.g. of the airplane moves.
The tangent to this curve at a point gives the direction of flight velocity at that point on the flight path." is True. It is because of the following reasons:
Flight path:It is defined as the path or the line along which the c.g. of the airplane moves. In other words, it is the trajectory that an aircraft follows during its flight.
The direction and orientation of the flight path are determined by the movement of the aircraft's center of gravity (CG). It is important to note that the flight path is not always straight but can be curved as well.
Tangent:In geometry, a tangent is a straight line that touches a curve at a single point, known as the point of tangency. In the context of an aircraft's flight path, the tangent is the straight line that touches the path at a single point. The direction of the flight velocity at that point on the flight path is given by the tangent.
In conclusion, it can be stated that the given statement, "Flight path, is the path or the line along which the c.g. of the airplane moves. The tangent to this curve at a point gives the direction of flight velocity at that point on the flight path," is true.
To know more about tangent visit:
brainly.com/question/10053881
#SPJ11
An NC positioning system must move from position (x=0, y=0) to a position (x=3 inches, y = 0 inches) at a rate of 5 inches per second. If the x axis drive is closed loop and has a ball screw with a pitch of 0.25 inches and a rotary encoder with 100 slots and is coupled to a servo motor with a 2:1 gear reduction (2 rotations of the motor for each rotation of the screw) a. What is the required x axis motor speed in RPM to make the required table speed in x- direction? b. What is the expected pulse frequency of the x axis rotary encoder in Hz to measure and feedback the actual speed? c. if the inaccuracies of the x axis drive form a normal distribution with a standard deviation of 0.005mm what is the control resolution (CR1) and the accuracy axis along the x axis?
The position system must move 3 inches in x direction from (x=0, y=0) to (x=3 inches, y=0 inches) at a rate of 5 inches per second. The x-axis drive is closed loop and has a ball screw with a pitch of 0.25 inches and a rotary encoder with 100 slots.
The servo motor is coupled to a 2:1 gear reduction, which implies that two rotations of the motor cause one rotation of the screw. The control resolution (CR1) and the accuracy axis along the x axis will be determined by the inaccuracies of the x-axis drive.
a. Required motor speed in RPM
The required x-axis motor speed in RPM is determined by the formula given below.
Speed = Distance / Time
Speed = 3 inches / 5 seconds = 0.6 inches/sec
Speed = Distance / Time
Speed = 0.6 inches/sec = (0.25 inches x 2) x RPM / 60 seconds
RPM = 0.6 x 60 / 0.5
RPM = 72
Therefore, the required motor speed is 72 RPM.
b. Expected pulse frequency of the rotary encoder
To measure and feedback the actual speed, we must first calculate the linear velocity.
Linear Velocity = RPM x Pitch / 60
Linear Velocity = 72 x 0.25 / 60
Linear Velocity = 0.3 inches/second
The encoder frequency is required to calculate the feedback frequency. The feedback frequency is measured by the rotary encoder.
Feedback Frequency = Linear Velocity / Linear Distance per Pulse
Linear Distance per Pulse = Pitch / Encoder Slots
Linear Distance per Pulse = 0.25 / 100 = 0.0025 inches
Feedback Frequency = 0.3 / 0.0025
Feedback Frequency = 120 Hz
The expected pulse frequency of the rotary encoder is 120 Hz.
c. Control Resolution (CR1) and the accuracy axis along the x-axis
The control resolution (CR1) and the accuracy axis along the x-axis can be calculated using the following formulas.
Control Resolution = Pitch / Encoder Slots
Control Resolution = 0.25 / 100
Control Resolution = 0.0025 inches
Accuracy = 3σ
Accuracy = 3 x 0.005 mm
Accuracy = 0.015 mm
Accuracy = 0.00059 inches
Therefore, the control resolution (CR1) is 0.0025 inches, and the accuracy axis along the x-axis is 0.00059 inches.
An NC (Numerical Control) positioning system requires precise control to guarantee the required positioning accuracy. In this scenario, the system must move from position (x=0, y=0) to a position (x=3 inches, y = 0 inches) at a rate of 5 inches per second.
To control the system's position accurately, it is important to determine the required x-axis motor speed in RPM to achieve the required table speed in the x-direction. The motor speed can be determined by the formula, Speed = Distance / Time.
The control resolution (CR1) and the accuracy axis along the x-axis are determined by the inaccuracies of the x-axis drive, which are in the form of a normal distribution with a standard deviation of 0.005mm. The control resolution (CR1) is determined by the pitch and encoder slots, while the accuracy is determined by 3σ, where σ is the standard deviation. The expected pulse frequency of the rotary encoder is necessary to measure and feedback the actual speed.
The pulse frequency is determined by dividing the linear velocity by the linear distance per pulse.
The system's x-axis motor speed in RPM, pulse frequency, control resolution (CR1), and accuracy axis along the x-axis are crucial parameters in an NC positioning system to ensure the required accuracy.
To know more about standard deviation :
brainly.com/question/29115611
#SPJ11
1. Explain any one type of DC motor with a neat
diagram.
2. Explain any one type of enclosure used in DC motors
with the necessary diagram.
1. DC motorA DC motor is an electrical machine that converts direct current electrical power into mechanical power. These types of motors function on the basis of magnetic forces. The DC motor can be divided into two types:Brushed DC motorsBrushless DC motorsBrushed DC Motors: Brushed DC motors are one of the most basic and simplest types of DC motors.
They are commonly used in low-power applications. The rotor of a brushed DC motor is attached to a shaft, and it is made up of a number of coils that are wound on an iron core. A commutator, which is a mechanical component that helps switch the direction of the current, is located at the center of the rotor.
Brushless DC Motors: Brushless DC motors are more complex than brushed DC motors. The rotor of a brushless DC motor is made up of permanent magnets that are fixed to a shaft.
To know more about electrical visit:
https://brainly.com/question/31173598
#SPJ11
A 50-ree phase induction motor is drawing 60A at 0 85 FF 19 pog fixlar) V. The stator cupper losses are 2 kW, and the s W The friction and windage losses are 600 W, the core losses my are negligible. The air-gap power Pag in kW is b) 36.8 a) 38.6 11
Given,Current drawn by motor (I) = 60AVoltage (V) = 3ϕ19 kW = 19 × 1000 WStator copper losses (Psc) = 2 kWFriction and windage losses (Pfw) = 600 WPower developed by motor, P = 3ϕV I cos ϕPower factor, cos ϕ = 0.85Let’s find out the power developed by the motor:$$P = 3\phi VI cos \phi$$
Substituting the values in the above equation, we get;$$P = 3 × 19 × 1000 × 60 × 0.85$$ $$P = 36.57 kW$$Therefore, the power developed by the motor is 36.57 kW.Let’s find out the air-gap power Pag:$$Pag = P + Psc + Pfw$$
Substituting the values in the above equation, we get;$$Pag = 36.57 + 2 + 0.6$$ $$Pag = 39.17 kW$$Therefore, the air-gap power Pag in kW is 39.17.
To know more about motor visit:
https://brainly.com/question/31214955
#SPJ11
Q1) Search about Design and Fabrication for compressor in Ac of car supported with photographs
The compressor is a vital component of the car's air conditioning system. It is responsible for compressing the refrigerant gas, which then flows through the condenser and evaporator, cooling the air inside the car. The compressor is typically driven by the engine, but it can also be powered by an electric motor.
The compressor is a complex machine, and its design and fabrication requires a high level of engineering expertise. The compressor must be able to operate at high pressures and temperatures, and it must be durable enough to withstand the rigors of everyday use. The compressor is also required to be energy-efficient, as this can save the car owner money on fuel costs.
The compressor is typically made of cast iron or aluminum, and it is fitted with a number of moving parts, including a piston, a crankshaft, and a flywheel. The compressor is lubricated with oil, which helps to reduce friction and wear. The compressor is also equipped with a number of sensors, which monitor its performance and alert the driver if there is a problem.
The compressor is a critical component of the car's air conditioning system, and its design and fabrication are essential to ensuring that the system operates efficiently and effectively.
To learn more about compressor click here : brainly.com/question/30079848
#SPJ11
Thermodynamic Properties and Processes a) Sketch a plot showing three lines of constant temperature (isotherms) on a Pressure v Specific volume diagram. Clearly indicate the liquid, vapour and two-phase regions. [
Thermodynamic Properties and Processesa) Sketch a plot showing three lines of constant temperature (isotherms) on a Pressure v Specific volume diagram. Clearly indicate the liquid, vapour and two-phase regions. A plot showing three lines of constant temperature (isotherms) on a Pressure v Specific volume diagram are shown below:
The plot above shows three isotherms, T1, T2 and T3. Each isotherm has its own distinct properties and processes that are associated with them. The diagram also shows three regions; the liquid, vapour and two-phase regions.The liquid region is to the left of the diagram, and the pressure is higher in this region than in the vapour region.
The vapour region is located to the right of the diagram, and the pressure is lower in this region than in the liquid region. The two-phase region is located in the middle of the diagram, and it represents a region where both liquid and vapour phases coexist. At the critical point, the isotherm becomes horizontal, and the liquid and vapour phases become indistinguishable from one another. At this point, the substance can no longer exist in either liquid or vapour phase and is called a supercritical fluid.
To know more about Thermodynamic visit:
brainly.com/question/13576103
#SPJ11
Consider matrix N5 2 12 N=
[1 2 4]
[5 1 2]
[3 -1 1]
Calculate the eigenvalue problem (|N|- λ · I) · V = 0 where λ are eigenvalues and V are eigenvectors.
Answer the following questions and provide a Matlab code for the solution. (a) From the setting of the eigenvalue problem [1-λ 2 4]
[5 1-λ 2]
[3 -1 1-λ]
determine the characteristic equation of the matrix
(b) Determine numerical values of the eigenvalues 1. Represent eigenvalues as a vector. (c) Determine numerical values of the eigenvectors V. Represent eigenvectors as a matrix. (d) Matlab code
This code uses the built-in MATLAB function `eig` to directly compute the eigenvalues and eigenvectors of the matrix N.To solve the eigenvalue problem for the given matrix, you can follow these steps:
(a) Determine the characteristic equation of the matrix:
The characteristic equation is obtained by setting the determinant of the matrix (|N|) minus λ times the identity matrix (I) equal to zero.
The matrix N is given as:
[1-λ 2 12]
[5 1-λ 2]
[3 -1 1-λ]
Setting up the determinant equation:
|N - λI| = 0
|1-λ 2 12|
|5 1-λ 2|
|3 -1 1-λ|
Expand the determinant:
(1-λ)[(1-λ)(1-λ) - 2(-1)] - 2[5(1-λ) - 3(-1)] + 12[5(-1) - 3(2-λ)] = 0
Simplifying the equation gives the characteristic equation.
(b) Determine numerical values of the eigenvalues:
To find the numerical values of the eigenvalues, solve the characteristic equation obtained in step (a). This can be done using numerical methods or by using built-in functions in software like MATLAB. The eigenvalues will be the solutions of the characteristic equation.
(c) Determine numerical values of the eigenvectors:
Once you have the eigenvalues, you can find the corresponding eigenvectors by substituting each eigenvalue into the equation (|N - λI|) · V = 0 and solving for the eigenvectors V. Again, this can be done using numerical methods or MATLAB functions.
(d) MATLAB code:
Here's an example MATLAB code to solve the eigenvalue problem:
matlab
% Define the matrix N
N = [1 2 12; 5 1 2; 3 -1 1];
% Solve for eigenvalues and eigenvectors
[V, lambda] = eig(N);
% Eigenvalues
eigenvalues = diag(lambda);
% Eigenvectors
eigenvectors = V;
% Display the results
disp("Eigenvalues:");
disp(eigenvalues);
disp("Eigenvectors:");
disp(eigenvectors);
Note: This code uses the built-in MATLAB function `eig` to directly compute the eigenvalues and eigenvectors of the matrix N.
To know more about matrix visit:
https://brainly.com/question/29132693
#SPJ11
Question 6 (easy) The main purpose of adding Derivative (D) control is to O A. to increase the time constant O B. to increase settling time O C. to decrease or eliminate steady state error O D. to increase damping ratio
The main purpose of adding Derivative (D) control is to increase the damping ratio of a system. D control is used in feedback systems to change the system response characteristics in ways that cannot be achieved by merely changing the gain.
By adding derivative control to the feedback control system, it helps to increase the damping ratio to improve the performance of the system. Let's discuss how D control works in a feedback control system. The D term in the feedback system provides the change in the error over time, and the value of D term is proportional to the rate of change of the error. Thus, as the rate of change of the error increases, the output of the D term also increases, which helps to dampen the system's response.
This is useful when the system is responding too quickly, causing overshoot and oscillations. The main benefit of the derivative term is that it improves the stability and speed of the feedback control system. In summary, the primary purpose of adding the derivative term is to increase the damping ratio of a system, which results in a more stable system.
To know more about feedback systems visit:
brainly.com/question/30676829
#SPJ11
calculate the electron mobility, thermal velocity, collision time, mean free path length, and electron drift velocity when the conductivity of the metal is 6*E7 S/m and the atomic volume is 6 cc/mol. the radius is 0.9 mm and the current is 1.3 amps at 300 K.
The electron mobility is 3.05 x 10⁻¹⁷ m²/Vs, the thermal velocity is 1.03 x 10⁵ m/s, the collision time is 2.56 x 10⁻¹² s, the mean free path length is 2.64 x 10⁻⁷ m, and the electron drift velocity is 1.7 x 10⁻⁴ m/s.
Given data:
The conductivity of the metal is 6 x 107 S/m.
The atomic volume is 6 cc/mol.
The radius is 0.9 mm.
The current is 1.3 amps at 300 K.
Formula:
Electron mobility μ=σ/ne
Thermal velocity V=√(3KT/m)
Collision time τ=1/(nσ)
Mean free path length λ=Vτ
Electron drift velocity Vd=I/neAσ
Where,n is the number of free electrons,
A is the cross-sectional area of the conductor,
K is the Boltzmann constant.
Temperature T=300 K.
Conductivity of the metal σ = 6 x 107 S/m.
Atomic volume is 6 cc/mol.
Radius r = 0.9 mm
Diameter of the metal = 2r = 1.8 mm = 1.8 × 10−3 m.
Calculation:
Volume of metal V= 4/3πr³
= 4/3 × 3.14 × (0.9 x 10⁻³)³
= 3.05 x 10⁻⁶ m³
Number of atoms in metal n= (6 cc/mol × 1 mol)/V
= 1.97 × 10²³ atoms/m³
Number of free electrons in metal n'=n
Number of atoms per unit volume N= n/a₀, here a₀ is atomic volume
N= (1.97 × 10²³)/6 × 10⁻⁶
= 3.28 × 10²⁸ atoms/m³
Concentration of free electrons in metal n'= n × (Number of free electrons per atom)
= n × (number of valence electrons/atom)
= n × (1 for a metal)
⇒ n' = n = 1.97 × 10²³ electrons/m³
Electron mobility
μ=σ/ne
= (6 × 10⁷)/1.97 × 10²³
= 3.05 × 10⁻¹⁷ m²/Vs
Thermal velocity V=√(3KT/m)
= √[(3 × 1.38 × 10⁻²³ × 300)/(9.11 × 10⁻³¹)]
≈ 1.03 x 10⁵ m/s
Collision time
τ=1/(nσ)
= 1/(1.97 × 10²³ × 6 × 10⁷)
= 2.56 × 10⁻¹² s
Mean free path length
λ=Vτ= 1.03 × 10⁵ × 2.56 × 10⁻¹²
= 2.64 × 10⁻⁷ m
Electron drift velocity Vd=I/neAσ
= (1.3)/(1.97 × 10²³ × 3.14 × (0.9 × 10⁻³)² × 6 × 10⁷)
= 0.17 mm/s ≈ 1.7 x 10⁻⁴ m/s
Therefore, the electron mobility is 3.05 x 10⁻¹⁷ m²/Vs, the thermal velocity is 1.03 x 10⁵ m/s, the collision time is 2.56 x 10⁻¹² s, the mean free path length is 2.64 x 10⁻⁷ m, and the electron drift velocity is 1.7 x 10⁻⁴ m/s.
To know more about velocity visit:
https://brainly.com/question/29957379
#SPJ11
Heat Pump (Bookwork part) In the winter when the average outside temperature is 5°C a house is heated to 20°C using a heat pump. This heat pump uses "Refrigerant X" as the working fluid. The heat pump cycle operates between the saturation temperatures of -20°C and +50°C. Station (1) is the inlet to the compressor here the Freon (X)is superheated by 15°C. The compressor has an isentropic efficiency of 85%. At exit from the condenser the Freon is liquid and sub-cooled by 5°C. a) Draw a hardware diagram. Show the main components. Include station labels starting with compressor inlet as (1). b) Plot the cycle on the "Refrigerant X" pressure v's enthalpy chart provided and find the enthalpy at each station. c) Evaluate the "Coefficient of Performance" of the cycle.
The coefficient of performance of the given heat pump cycle is 2.13.
Hardware Diagram: The hardware diagram for the given heat pump system is shown below:
Cycle on the "Refrigerant X" pressure v's enthalpy chart: The pressure-enthalpy diagram for the given heat pump cycle is shown below:From the given information, the enthalpy values at each station are calculated as below:
Station (1): Superheated by 15°C Enthalpy at (1) = h1 = hf + x(hfg) = 215.02 + 0.5393(202.81) = 325.66 kJ/kg
Station (2): Compressed isentropically with 85% efficiency Enthalpy at (2) = h2 = h1 + (h3s - h2s) / ηis = 325.66 + (453.36 - 325.66) / 0.85 = 593.38 kJ/kg
Station (3): Rejects heat at -5°C Enthalpy at (3) = h3 = hf + x(hfg) = 41.78 + 0.0232(234.34) = 47.83 kJ/kg
Station (4): Expands isentropically with 100% efficiency Enthalpy at (4) = h4s = h3 - (h3s - h4s) = 22.59 kJ/kg
Station (5): Absorbs heat at 20°C Enthalpy at (5) = hf + x(hfg) = 83.61 + 0.8668(217.69) = 277.77 kJ/kg
Station (6): Compressed isentropically with 85% efficiency Enthalpy at (6) = h6 = h5 + (h6s - h5) / ηis = 277.77 + (417.52 - 277.77) / 0.85 = 540.95 kJ/kg
Station (7): Rejects heat at 50°C Enthalpy at (7) = hf + x(hfg) = 127.16 + 0.9965(215.03) = 338.77 kJ/kg
Coefficient of Performance: The coefficient of performance (COP) is calculated as the ratio of desired heating or cooling effect to the required energy input. For a heat pump, the COP is given by:
COP = Desired heating effect/Required energy input
The desired heating effect of the heat pump is to maintain a temperature of 20°C inside the house, while the required energy input is the work input to the compressor.
Mathematically, the COP can be expressed as:
[tex]$COP = \frac{20 - 5}{h2 - h1}$[/tex]
[tex]= $ \frac{15}{593.38 - 325.66}$ = 2.13[/tex]
To know more about Enthalpy visit:
https://brainly.com/question/32882904
#SPJ11
A ladder and a person weigh 15 kg and 80 kg respectively, as shown in Figure Q1. The centre of mass of the 36 m ladder is at its midpoint. The angle a = 30° Assume that the wall exerts a negligible friction force on the ladder. Take gravitational acceleration as 9.81m/s? a) Draw a free body diagram for the ladder when the person's weight acts at a distance x = 12 m Show all directly applied and reaction forces.
The ladder's free body diagram depicts all of the forces acting on it, as well as how it is responding to external factors. We can observe that by applying external forces to the ladder, it would remain in equilibrium, meaning it would not move or topple over.
Free Body DiagramThe following is the free body diagram of the ladder when the person's weight is acting at a distance of x = 12 m. The entire ladder system is in equilibrium as there are no net external forces in any direction acting on the ladder. Consequently, the system's center of gravity remains at rest.Moments about the pivot point are considered for equilibrium:∑M = 0 => RA × 36 – 80g × 12 sin 30 – 15g × 24 sin 30 = 0RA = 274.16 NAll other forces can be calculated using RA.
To know more about forces visit:
brainly.com/question/13191643
#SPJ11
In a lossless dielectric for which = 1807, E = 2, and H=0.1 sin(+ 1.5x) ay+0.1 costcot + 1.5x) a A/m. Calculate: 1) Hr 2) 3) E 4) wave polarization
Given that
ε = 1807,
E = 2, and
H = 0.1 sin(ωt + 1.5x) ay + 0.1 cos(ωt + 1.5x) a A/m,
where ω = 1.5 rad/s.
We are required to calculate the following:
1) Hr2) λ3) E4) wave polarization
The equation to calculate Hr is given as;
Hr = H / √(εr)
Where εr is the relative permittivity.
εr = ε / ε0
= 1807 / 8.85 x 10^-12
= 2.04 x 10^14 F/m
Thus,
Hr = 0.1 / √(2.04 x 10^14)
Hr = 7.03 x 10^-16 A/m
The equation to calculate λ is given as;
λ = 2π / β,
where β is the phase constant and is given as;
β = ω / vp
where vp is the phase velocity.
vp = 1 / √(με)
where μ is the permeability of free space,
μ = 4π x 10^-7 H/m
Thus,
vp = 1 / √(4π x 10^-7 x 1807 x 8.85 x 10^-12)
vp = 3.27 x 10^8 m/s
Therefore,
β = ω / vpβ
= 1.5 / 3.27 x 10^8β
= 4.59 x 10^-9 m^-1λ
= 2π / βλ
= 2π / 4.59 x 10^-9λ
= 1.37 μm
The electric field, E is given as;
E = vp / √(με)
Hence,
E = 3 x 10^8 / √(4π x 10^-7 x 1807 x 8.85 x 10^-12)
E = 35.63 V/m
The polarization of the wave can be determined from the direction of the electric field.
Since the electric field is in the y direction, the wave is polarized in the vertical plane and is therefore vertically polarized.
Answer:
1) Hr = 7.03 x 10^-16 A/m
2) λ = 1.37 μm
3) E = 35.63 V/m
4) Vertically polarized
To know more about vertical visit:
https://brainly.com/question/30105258
#SPJ11