A rock thrown horizontally from the roof edge of a 12.4 m-high building hits the ground below, a horizontal distance of 17.8 m from the building. What is the overall speed of the rock when it hits the ground?

The amplitude of the magnetic field of the electromagnetic wave is 6.53 x 10^-7 T.

To find the amplitude of the magnetic field of an electromagnetic wave, we need to use the relationship between the electric and magnetic fields in an electromagnetic wave.

According to this relationship, the amplitude of the magnetic field is equal to the amplitude of the electric field divided by the speed of light (c). Therefore, if the amplitude of the electric field of an electromagnetic wave is 196 V/m, the amplitude of the magnetic field can be calculated as follows:

Amplitude of magnetic field = Amplitude of electric field / Speed of light
Amplitude of magnetic field = 196 V/m / 3 x 10^8 m/s
Amplitude of magnetic field = 6.53 x 10^-7 T

It is important to note that the amplitude of the magnetic field and the electric field of an electromagnetic wave are perpendicular to each other and are responsible for the wave's propagation through space.

To learn more about : electromagnetic

https://brainly.com/question/13874687

#SPJ11

To make bulb H dimmer than it was in Circuit 9 (when 1 glow flowed through it), you will need to decrease the flow through H. To achieve this, you can:

1. Increase the resistance in the circuit, specifically in the path that includes bulb H. This can be done by adding more resistors or increasing the resistance of the existing components.
2. Decrease the voltage across the circuit. This will result in a reduced current flow, making bulb H dimmer.

By decreasing the flow through H, you will effectively make the bulb dimmer than it was in Circuit 9.

To know more about Resistance and Voltage:

https://brainly.com/question/30740265

#SPJ11

The resistance of R1 and R2 in parallel is lower than their resistance in series.

When two resistors, R1 and R2, are in parallel, the equivalent resistance is calculated as

R = (R1 * R2) / (R1 + R2).

The resulting resistance is always lower than either of the individual resistors. In contrast, when R1 and R2 are in series, the equivalent resistance is calculated as R = R1 + R2. The resulting resistance is always higher than either of the individual resistors.

1. Resistance in Series: In a series circuit, the total resistance R(total) is the sum of the individual resistances (R1 and R2). Mathematically, it is given by:
R (total)= R1 + R2
2. Resistance in Parallel: In a parallel circuit, the total resistance R(total) is found using the reciprocal formula. Mathematically, it is given by:
1/R(total) = 1/R1 + 1/R2
Now, let's compare the two cases:
In a series circuit, the total resistance is simply the sum of the individual resistances, whereas in a parallel circuit, the total resistance is determined by the reciprocal formula. Generally, the total resistance in a parallel circuit is lower than that in a series circuit, due to the reciprocal relationship. This means that when R1 and R2 are connected in parallel, their combined resistance will be less than when they are connected in series.

For more such questions on resistance , Visit:

https://brainly.com/question/28135236

#SPJ11

The time required for the object attached to a spring to move from the equilibrium position to half the amplitude depends on the specifics of the motion and cannot be determined solely from the period of oscillation.

During its motion, the object attached to a spring oscillates with a sinusoidal motion, which means its speed is not constant. At the maximum displacement, the speed is zero, while it is maximum when the object passes through the equilibrium position. Therefore, the time required for the object to move from the equilibrium position to half the amplitude is not half the period, but rather a smaller fraction of the period.

To determine the time required, one would need to use the equation of motion for a simple harmonic oscillator:

x(t) = A cos(ωt + φ)

where x(t) is the position of the object at time t, A is the amplitude, ω is the angular frequency, and φ is the phase constant. From this equation, we can find the position of the object when it is halfway to the amplitude by setting x(t) equal to A/2 and solving for t:

A/2 = A cos(ωt + φ)

cos(ωt + φ) = 1/2

ωt + φ = ±π/3

t = (±π/3 - φ) / ω

Therefore, the time required for the object to move from the equilibrium position to half the amplitude depends on the phase constant φ and the angular frequency ω. It is important to note that this is a general solution for a simple harmonic oscillator, and specific values for these variables would need to be provided to obtain a numerical answer.

Learn more about harmonic oscillator:

https://brainly.com/question/30354005

#SPJ4

Zach's weight before the elevator starts braking is 833 Newton.

Identifying Zach's weight is necessary to prevent the braking of the lift in which he is now riding. Zach is 85 kg in weight and the lift is dropping at 11 m/s.

The first floor is reached after 2.5 seconds of braking by the elevator. We employ the weight formula—which is the sum of mass and gravity—to solve the issue.

Zach's weight can be determined by dividing his mass of 85 kg by the gravitational acceleration, which equals about 9.8 m/s2. This results in an 833 Newton weight before the lift begins to brake.

Learn more about weight:

https://brainly.com/question/30176113

#SPJ4

The maximum torque on the wire is 0.1306 Nm.

Hi, I'd be happy to help you with your question. To find the maximum torque on a wire formed into a circle with a diameter of 10.9 cm, placed in a uniform magnetic field of 2.80 mT, and carrying a current of 5.00 A, follow these steps:

1. Calculate the radius of the circle:
Radius = Diameter / 2 = 10.9 cm / 2 = 5.45 cm = 0.0545 m (converted to meters)

2. Calculate the area of the circle:
Area = π * Radius^2 = π * (0.0545 m)^2 = 0.00933 m^2

3. Convert the magnetic field from millitesla (mT) to tesla (T):
Magnetic Field = 2.80 mT = 0.00280 T

4. Calculate the maximum torque on the wire:
Torque = (Current * Area * Magnetic Field) * sin(θ)
Since we need to find the maximum torque, we will use sin(θ) = 1:
Torque = (5.00 A * 0.00933 m^2 * 0.00280 T) * 1 = 0.1306 Nm

The maximum torque on the wire is 0.1306 Nm.

Learn more about torque

brainly.com/question/25708791

#SPJ11

The tower of Pisa can lean up to an additional 3.5 m off center before becoming unstable.

To determine how much farther the tower can lean before it becomes unstable, we need to calculate the current location of the center of mass and the maximum distance it can move before leaving the base.

Assuming the tower is a uniform cylinder, we can calculate the location of its center of mass using the formula:

x_cm = L/2 + h/4

where L is the length of the cylinder (equal to the diameter, or 7.0 m), and h is the height of the cylinder (equal to 55 m).

Substituting the given values, we get:

x_cm = 7.0/2 + 55/4

x_cm = 5.25 + 13.75

x_cm = 19.0 m

This means that the center of mass of the tower is currently located 19.0 m from the center of the base.

To determine how much farther the tower can lean before becoming unstable, we need to calculate the maximum distance the center of mass can move before leaving the base. This distance is equal to half the diameter of the base, or:

d_max = 7.0/2

d_max = 3.5 m

To know more about Leaning Tower of Pisa:

https://brainly.com/question/30554306

#SPJ4

In the heat transfer relation for a heat exchanger, the quantity f is called the "effectiveness." It represents the ratio of the actual heat transfer rate in the heat exchanger to the maximum possible heat transfer rate under the given conditions.

The quantity f in the heat transfer relation for a heat exchanger is called the heat transfer coefficient correction factor. It represents the ratio of the actual heat transfer coefficient to the theoretical heat transfer coefficient. It takes into account the effects of fluid properties, flow conditions, and heat exchanger geometry on the heat transfer process.

Yes, f can be greater than 1. This occurs when the actual heat transfer coefficient is higher than the theoretical heat transfer coefficient, which can happen when there are enhancements to the heat transfer surface or when the fluid flow is optimized.

To know more about heat transfer coefficient correction factor:
https://brainly.com/question/30981087

#SPJ11

Protons have a positive charge, neutrons have no charge, and electrons have a negative charge.

The three fundamental particles in an atom are protons, neutrons, and electrons. Protons have a positive charge and are located in the nucleus of the atom, along with neutrons, which have no charge. Electrons have a negative charge and orbit the nucleus. The number of protons in an atom determines its atomic number, which in turn determines the element to which it belongs.

The number of electrons in an atom determines its chemical properties, as they are involved in chemical bonding with other atoms. The charges of the particles are important in determining the behavior of atoms in chemical reactions and in the formation of molecules and compounds.

To know more about charge, here

brainly.com/question/3412043

#SPJ4

--The complete question is, Which fundamental particles have positive charges, and which have negative charges?--

The spring constant of the spring is 3.00N/m. Therefore option 3 is correct.

To find the spring constant, we can use Hooke's Law, which states that the force exerted by a spring is directly proportional to the displacement of the spring from its equilibrium position.

The formula for Hooke's Law is F = kx, where F is the force, k is the spring constant, and x is the displacement.

In this case, we are given that compressing the spring by 0.500m causes a force of 1.50N. Using the formula F = kx, we can substitute the values:

1.50N = k * 0.500m

To find the value of k, we can rearrange the equation:

k = F / x

k = 1.50N / 0.500m

k = 3.00N/m

Therefore, the spring constant of the spring is 3.00N/m, which corresponds to option 3.

Know more about Hooke's Law:

https://brainly.com/question/30379950

#SPJ2

As the ball is pulled inward, the radius of the circle decreases, which means that the tangential speed of the ball must increase in order to maintain uniform centripetal motion. Option (A)

This increase in tangential speed means that the angular velocity of the ball also increases, as angular velocity is directly proportional to tangential speed divided by the radius of the circle.

Since angular momentum is given by the product of rotational inertia and angular velocity, any change in angular velocity will result in a change in angular momentum.

As a result, the proper prediction for the angular momentum and rotational inertia of the ball about the axis of revolution as the ball is drawn inward is: A) The angular momentum of the ball rises. The rotational inertia of the ball about the axis of revolution remains constant.

Learn more about tangential speed

https://brainly.com/question/29860420

#SPJ4

If Canada were to build its own rockets and launch them into space, it would need to adhere to international standards and regulations set by the Fédération Aéronautique Internationale or FAI.

The FAI is a governing body that oversees international aviation and spaceflight activities, and its mission is to promote safe and responsible practices in air and space travel. The FAI maintains records of achievements in air and space activities and coordinates with national and international organizations to ensure compliance with regulations and guidelines.

In order for a mission to qualify as an official spaceflight, the FAI would need to be petitioned and the mission would need to adhere to its standards and regulations. These regulations include safety measures, technical specifications, and environmental impact assessments, among others.

By adhering to these regulations, Canada could ensure safe and responsible spaceflight activities and contribute to the development of the international space community and NASA.

To know more about NASA, visit:

https://brainly.com/question/20763143

#SPJ1

This is due to the fact that the gravitational pull of the sun is proportionate to the mass of each body, with the larger body being subjected to a stronger gravitational pull than the smaller body.

Depending on how far away from the Sun a planet is, it orbits the Sun at a different speed. When a planet is closer to the Sun, it moves more quickly due to the Sun's stronger gravitational pull.

A planet's angular momentum does not change as it gets further from the Sun, thus it moves more slowly at that distance. The angular momentum of a planet in a circular orbit is determined by its mass (m), its distance from the Sun (d), and its velocity (v).

To know more about momentum visit:-

https://brainly.com/question/30677308

#SPJ1

The forces at the left support are 1.61 x 105 N upward and the forces at the right support are 8.88 × 105 N downward by taking into account the forces acting on the bridge and the vehicle.

Finding the forces on a bridge with a truck positioned 15.0 metres from one end and piers supporting it at each end is the task at hand in this challenge. The truck weighs 2.50 x 104 kg, whereas the bridge is 50.0 metres long and 8.20 x 104 kg in weight.

The forces acting on the bridge at its places of support must be determined using Newton's laws of motion. We may determine that the forces at the left support are 1.61 x 105 N upward and the forces at the right support are 8.88 × 105 N downward by taking into account the forces acting on the bridge and the vehicle.

Learn more about forces:

https://brainly.com/question/30526425

#SPJ4

The complete question:

A bridge of length 50.0 m and mass 8.20×10^4 kg is supported on a smooth pillar at each end as shown. A truck of mass 2.50×10^4 kg is located 15.0 m from one end. What are the forces of the bridge at the points of support?

The angular velocity of the track star is approximately 0.105 radians/second.

The time taken to run the race is 60 seconds, and the distance covered by the track star is one lap, which is the circumference of the circle. Therefore, the average speed of the track star is:

Average speed = distance / time

Average speed = 2πr / 60 seconds

Average speed = (2π x 63.66 meters) / 60 seconds

Average speed = 6.67 meters/second (rounded to two decimal places)

The angular velocity (ω) of the track star can be calculated using the formula: ω = v / r

where v is the linear velocity of the track star, and r is the radius of the circular track. Since the track star is running at a constant speed, the linear velocity is equal to the average speed calculated above. Therefore, the angular velocity of the track star is:

ω = v / r

ω = 6.67 meters/second / 63.66 meters

ω = 0.105 radians/second (rounded to three decimal places)

To know more about angular velocity:

https://brainly.com/question/30885221

#SPJ4

This statement is incorrect. The correct form of solid waste recycling in which the energy value of combustible waste materials is recovered is called "waste-to-energy" or "energy recovery."

Composting is a different form of solid waste recycling that involves the biological decomposition of organic materials to create a nutrient-rich soil amendment.

Here is a step-by-step explanation of the correct process:

Waste-to-energy (WTE) facilities receive solid waste, typically municipal solid waste, which is then sorted to remove recyclable materials such as plastics, metals, and paper.

The remaining waste is then burned in a specially designed furnace, called an incinerator, at high temperatures to create steam.

The steam drives turbines, which generate electricity that can be sold to the grid.

In addition to electricity generation, WTE facilities also recover the heat generated by the incineration process to provide heat to nearby buildings or industries.

The remaining ash from the incineration process can be used as a construction material, such as for roadbeds or building foundations.

WTE facilities are highly regulated and must meet strict emissions standards to ensure that the air and water quality in surrounding communities is not negatively impacted.

Overall, WTE is a form of solid waste recycling that can provide both energy generation and waste reduction benefits, while also reducing the need for landfill space.

Composting, on the other hand, is a separate process that involves the natural decomposition of organic waste materials to create a valuable soil amendment for use in agriculture and landscaping.

To know more about combustible waste :

https://brainly.com/question/8242764

#SPJ11

James' gun emits the most energetic light as ultraviolet light has a higher frequency and shorter wavelength than infrared, red, and blue light.

The energy of light is determined by its frequency and wavelength. James' gun produces the most energetic light because ultraviolet light has a higher frequency and shorter wavelength than infrared, red, and blue light. This means that each photon of ultraviolet light carries more energy than a photon of blue, red, or infrared light.

Therefore, James' gun emits light with the highest energy. It is important to note that high-energy light, such as ultraviolet light, can be harmful to live organisms and precautions should be taken to limit exposure.

Learn more about ultraviolet:

https://brainly.com/question/31183067

#SPJ4

When an electrical current passes through a resistor, energy is dissipated, and the rate at which this energy is dissipated is the power, which is given by. [tex]P = i^{2} 2R[/tex] The amount of electricity passing through the resistor is determined by the current.

In the scenario described, when the switch is closed, the current prefers to travel through the short circuit wire rather than through bulb B, which causes no current to flow through bulb B. Since there is no current passing through bulb B, it does not receive any electrical energy and goes out.

On the other hand, all the current flows through bulb A, and thus, it receives more electrical energy, resulting in it getting brighter. This happens because the power dissipated by the resistor is proportional to the square of the current, and since all the current flows through bulb A, it receives more power and gets brighter.

In summary, the current passing through the resistor determines the amount of electricity passing through it, and the distribution of this current through different paths can result in some bulbs getting brighter, some getting dimmer, or even going out.

To know more about light bulb:

https://brainly.com/question/29107702

#SPJ4

A comet's tail points after its closest approach to the Sun:

When a comet approaches the Sun, the heat causes some of its frozen gases and ices to vaporize, creating a cloud of gas and dust around the nucleus of the comet.

The solar wind, which is a stream of charged particles constantly flowing out from the Sun, interacts with the gas and dust in the comet's atmosphere and pushes it away from the Sun.

The direction of the solar wind is generally outward from the Sun, so the gas and dust in the comet's tail is pushed in the opposite direction, away from the Sun.

The direction of the tail, therefore, is always away from the Sun, regardless of the position or motion of the comet.

Therefore, the correct answer is not among the options provided, but if we assume that the question is asking about the direction of the tail relative to the comet's direction of motion, the answer would be B) behind its direction of motion.

To know more about comet's :

https://brainly.com/question/28543341

#SPJ11

Baffles are flat plates or bars that are placed inside a shell-and-tube heat exchanger to promote turbulence and enhance heat transfer. The baffles create a series of parallel flow paths, forcing the fluid to change direction several times as it flows through the heat exchanger.

This results in an increase in the heat transfer coefficient by promoting better mixing and reducing the thickness of the thermal boundary layer.

The presence of baffles increases the pressure drop across the heat exchanger, which in turn increases the pumping power requirements. However, the increase in heat transfer coefficient outweighs the increase in pressure drop, resulting in an overall improvement in the heat transfer efficiency of the heat exchanger. The baffles also serve to support the tubes and prevent damage from tube vibration, which can occur in the absence of baffles.

The selection and design of baffles are critical to the performance of a shell-and-tube heat exchanger. The spacing, angle, and number of baffles must be carefully considered to optimize the heat transfer rate and minimize the pumping power requirements.

To learn more about baffles

https://brainly.com/question/30496310

#SPJ4

A mechanical wave is a wave that requires a medium to travel through, such as sound waves or water waves. In everyday life, we experience mechanical waves when we hear sounds or see water waves in a pond.

Transverse Wave: A transverse wave is a wave that vibrates perpendicular to the direction of wave propagation, such as light waves or radio waves.

We use transverse waves every day when we use our phones to receive radio waves.

Longitudinal Wave: A longitudinal wave is a wave that vibrates parallel to the direction of wave propagation, such as sound waves or seismic waves.

We hear sound through longitudinal waves, and we feel earthquakes through seismic waves.

Wave Speed: Wave speed is the speed with which a wave propagates via a particular medium.

When we watch a wave on the beach, we can estimate the wave speed by observing how fast it moves across the sand.

Wavelength: Wavelength is the distance between two corresponding points on a wave, such as the distance between two crests.

We can measure the wavelength of light using a spectroscope.

Frequency: Frequency is the number of waves that pass a given point in a given amount of time, such as the number of waves passing a fixed point in one second.

We use frequency to measure the pitch of sound or the radio frequency of a station.

Amplitude: Amplitude is the maximum displacement of a wave from its resting position, such as the height of a wave from its crest to its trough.

The amplitude of a sound wave determines how loud the sound is.

Learn more about waves here:

https://brainly.com/question/25954805

#SPJ1

The velocity at which the peak voltage of the generator is 475 V is 95.0 revolutions per minute.

The peak voltage (V) of a generator is given by the equation V = NBAω, where N is the number of turns in the coil, B is the magnetic field strength, A is the area of the coil, and ω is the angular velocity of the coil.

We are given that the coil has 475 turns, a diameter of 8.00 cm, and rotates in a 0.250 T field. We can use these values to find the area of the coil:

radius = diameter/2 = 4.00 cm

[tex]area = π(radius)^2 = 50.27 cm^2[/tex]

Now we can solve for ω:

V = NBAω

[tex]ω = V/(NBA) = (475 V)/(475 turns)(0.250 T)(50.27 cm^2)(1 m^2/10,000 cm^2)(1 rev/2π radians)[/tex]

ω = 95.0 rev/min

Therefore, the velocity at which the peak voltage of the generator is 475 V is 95.0 revolutions per minute.

Learn more about The velocity

https://brainly.com/question/17127206

#SPJ4

1260 RPM. RPM = (Peak Voltage / (2 * pi * coil diameter * magnetic field strength)) * 60 can be used to compute this.

The formula Vp = NABw/2, where N is the number of turns in the coil, A is the coil's area, B is the strength of the magnetic field, and w is the coil's angular velocity, determines the peak voltage produced by a revolving coil. We arrive at w = 2Vp/(NAB) after solving for w. Since the coil diameter rather than the area is provided, we can apply the calculation A = pi*d2/4 to determine the area. After simplifying and substituting the given variables, we get at w = 2 * 475 / (475 * pi * 0.082 * 0.25) = 420 rad/s. Finally, we increase this by 60 / (2 * pi), which gives us 1260 RPM.

learn more about coil here:

https://brainly.com/question/27961451

#SPJ11

The velocity of the astronaut as he moves backward is -0.33 m/s.

Velocity is the rate of change of dispalcement.

To calculate the velocity the astronaut moves backward, we use the formula below

Formula:

Where:

From  the question,

Given:

Substitute these values into equation 1 and solve for v

Hence, the velocity is -0.33 m/s.

Learn more about velocity here: https://brainly.com/question/24445340

#SPJ1

To find the focal length of a convex lens, we can use the formula:
1/f = 1/di + 1/do

Where f is the focal length, di is the distance of the image from the lens, and do is the distance of the object from the lens.

We are given that the student is 2.50m away from the lens, so do = 2.50m. We are also given that the image is 1.80m from the lens, so di = 1.80m.

Plugging these values into the formula, we get:
1/f = 1/1.80 + 1/2.50

Simplifying this equation, we get:
1/f = 0.5556

Multiplying both sides by f, we get:
f = 1.80 / 0.5556

Solving for f, we get:
f ≈ 3.24 meters

Therefore, the focal length of the convex lens is approximately 3.24 meters.

To know more about focal length of a convex lens:

https://brainly.com/question/1031772

#SPJ11

A convex lens is 1.80 meters from a student who is 2.50 meters distant, and its focal length is 1.04 meters.

To solve this problem, we can use the lens equation:

1/f = 1/do + 1/di

where f is the focal length of the lens, do is the object distance (distance of the object from the lens), and di is the image distance (distance of the image from the lens).

In this problem, the object distance is do = 2.50 m and the image distance is di = 1.80 m. We can plug these values into the lens equation and solve for the focal length:

1/f = 1/do + 1/di

1/f = 1/2.50 + 1/1.80

1/f = 0.4 + 0.56

1/f = 0.96

f = 1/0.96

f ≈ 1.04 meters

Therefore, the focal length of the convex lens is approximately 1.04 meters.

To learn more about focal length, refer:-

https://brainly.com/question/29870264

#SPJ11

The light wave is traveling in the +y direction, as its direction of propagation is perpendicular to both the electric and magnetic fields, which are oscillating in the -x and -z directions, respectively.

Based on the direction of the electric and magnetic fields, the wave is traveling in the +y direction (out of the page on a standard xy coordinate system).

This is because light waves are transverse waves, meaning that the direction of their oscillation (in this case, the electric and magnetic fields) is perpendicular to the direction of their propagation. In this case, the electric field is oscillating in the -x direction and the magnetic field is oscillating in the -z direction, which means that the wave is propagating in a direction perpendicular to both of these directions, which is the +y direction.

Learn more about The light wave

https://brainly.com/question/25588186

#SPJ4

The speed of the proton relative to the accelerator is approximately 0.82 times the speed of light.

In the special theory of relativity, the total energy of a particle can be expressed as the sum of its rest energy and its kinetic energy. If a proton in a certain particle accelerator has a kinetic energy that is equal to its rest energy, then its total energy is twice its rest energy, i.e.,

[tex]E_total^2 = (pc)^2 + (mc^2)^2[/tex]

where m is the rest mass of the proton and c is the speed of light.

According to the relativistic energy-momentum relation, the total energy of a particle is related to its momentum and rest mass by the equation:

[tex]E_total^2 = (pc)^2 + (mc^2)^2[/tex]

where p is the momentum of the particle.

Substituting the expression for the total energy of the proton in terms of its rest mass and the speed of light, we get:

[tex](2mc^2)^2 = (pc)^2 + (mc^2)^2[/tex]

Simplifying, we get:

[tex]4m^2c^4 = p^2c^2 + m^2c^4[/tex]

Rearranging and simplifying further, we get:

p = mc * sqrt(3)

Therefore, the momentum of the proton is mc times the square root of 3. Since the speed of the proton is related to its momentum by the equation:

[tex]p = mv / sqrt(1 - v^2/c^2)[/tex]

where v is the speed of the proton relative to the accelerator, we can solve for v to get:

[tex]v = c * sqrt(1 - 1/3) = c * sqrt(2/3)[/tex]

Therefore, the speed of the proton relative to the accelerator is approximately 0.82 times the speed of light.

Learn more about The speed

https://brainly.com/question/28224010

#SPJ4

The speed of the proton relative to the accelerator is 2.19 x 10⁸ m/s. in a certain particle accelerator, a proton has a kinetic energy that is equal to its rest energy.

Based on the given information, we can use the formula for kinetic energy:
KE = (1/2)mv²
where KE is the kinetic energy, m is the mass of the proton, and v is its velocity.
Since the proton's kinetic energy is equal to its rest energy (mc²), we can set the two equations equal to each other:
mc² = (1/2)mv²
Simplifying this equation, we can cancel out the mass on both sides:
c² = (1/2)v²
Solving for v, we can take the square root of both sides:
v = √(2c²)
Plugging in the value for the speed of light (c = 3.00 x 10⁸ m/s), we get:
v = √(2 x (3.00 x 10⁸)²)
v = 2.19 x 10⁸ m/s

To learn more about Proton Here:

https://brainly.com/question/30895149

#SPJ11

The temperature increases at a rate of 0.152 K/s

To determine the rate of temperature increase in the electronic circuit, we can use the formula:

Rate of temperature increase = Power absorbed / (mass × specific heat)

Here, the power absorbed is given as 8 mW, which is equal to 8 × [tex]10^{-3}[/tex] W or 8 × [tex]10^{-3}[/tex] J/s.

The mass of the silicon is 73 mg, which is equal to 73 × [tex]10^{-6}[/tex] kg.

The specific heat of silicon is 705 J/kg K.

Now, Substitute these values into the formula:

Rate of temperature increase = (8 × [tex]10^{-3}[/tex] J/s) / ((73 × [tex]10^{-6}[/tex] kg) × (705 J/kg K))

Rate of temperature increase = 0.152 K/s

So, the temperature of the electronic circuit increases at a rate of approximately 0.152 K/s when no heat can move out of it.

know more about electronic circuits here:

https://brainly.com/question/29639505

#SPJ11

the acceleration of the mass is 0.7212 m/s^2.

To find the acceleration of the mass, we need to first determine the net force acting on it. We can do this by using vector addition to add the two forces together.

Using the Pythagorean theorem, we can find the magnitude of the diagonal force:

sqrt[[tex](15N)^{2}[/tex] + [tex](10N)^{2}[/tex]] = sqrt[225 + 100] = sqrt(325) = 18.03 N

The direction of this force can be found using the inverse tangent function:

theta =[tex]tan^{-1}(10.0N/15.0N)[/tex] = 33.69 degrees north of east

We can now use vector addition to find the net force on the mass:

F_net = sqrt[[tex](15N)^{2}[/tex] + [tex](10N)^{2}[/tex]] = 18.03 N, at an angle of 33.69 degrees north of east

To find the acceleration of the mass, we can use Newton's second law, which states that the net force acting on an object is equal to its mass times its acceleration:

F_net = ma

Solving for the acceleration, we get:

a = F_net / m = 18.03 N / 25.0 kg = 0.7212 m/s^2

Therefore, the acceleration of the mass is 0.7212 m/s^2.

Learn more about Vector Addition:

https://brainly.com/question/19420810

Escape velocity is the minimum speed required for an object to escape the gravitational pull of a celestial body. It depends on the mass and radius of the celestial body, as well as the temperature and mass of the gas molecules in the atmosphere.

Based on a plot of escape velocity versus atmospheric temperature, we can see that lighter gases such as hydrogen and helium require lower escape velocities, while heavier gases such as nitrogen and oxygen require higher escape velocities. The plot also shows that the escape velocity decreases as the temperature of the gas increases.

Mars has a relatively low escape velocity compared to Earth, which means that lighter gases such as hydrogen and helium are more likely to escape into space. This suggests that Mars' atmosphere should retain heavier gases such as nitrogen and oxygen, which have higher escape velocities and are less likely to escape into space due to their mass. Therefore, it is likely that Mars' atmosphere is rich in heavier gases, which is consistent with current observations.

Learn more about celestial bod

https://brainly.com/question/28876984

#SPJ4

Yes, when a person is spinning in the x-y plane, they have a uniform circular motion.

Spinning is an exercise technique used to increase strength and endurance, as well as to burn fat. It involves using a stationary or spinning bike to simulate the experience of cycling outdoors. The intensity of the workout is determined by the instructor, usually by adjusting the resistance level of the bike. During a spinning session, the instructor will typically lead the class through a series of drills and exercises, while providing motivation and encouragement. Spinning is a great way to get a full body workout without having to go outdoors. It is also a low-impact activity that can be done by people of all fitness levels.

This is because the acceleration is constant and directed towards the centre of the circle, meaning that the speed and direction of the object remain the same throughout the motion. This is known as centripetal acceleration and it is what keeps the object moving in a uniform circle.

To learn more about spinning
https://brainly.com/question/29267031
#SPJ1