Answer:
1248m
The time that wave moves from the wave source to the ocean floor is half the total travel time: t = 2.5/2 = 1.25s
The speed of sound in seawater is 1560 m/s
Therefore, s = vt = (1560 m/s)(1.25s) =1248 m = 1.2km
An alternating current is supplied to an electronic component with a warning that the voltage across it should never exceed 12 V. What is the highest rms voltage that can be supplied to this component while staying below the voltage limit in the warning?
Answer:
The highest rms voltage will be 8.485 V
Explanation:
For alternating electric current, rms (root means square) is equal to the value of the direct current that would produce the same average power dissipation in a resistive load
If the peak or maximum voltage should not exceed 12 V, then from the relationship
[tex]V_{rms} = \frac{V_{p} }{\sqrt{2} }[/tex]
where [tex]V_{rms}[/tex] is the rms voltage
[tex]V_{p}[/tex] is the peak or maximum voltage
substituting values into the equation, we'll have
[tex]V_{rms} = \frac{12}{\sqrt{2} }[/tex] = 8.485 V
Two metal sphere each of radius 2.0 cm, have a center-to-center separation of 3.30 m. Sphere 1 has a chrage of +1.10 10^-8 C. Sphere 2 has charge of -3.60 10^-8C. Assume that the separation is large enough for us to assume that the charge on each sphere iss uniformly distribuuted.
A) Calculate the potential at the point halfway between the centers.
B) Calculate the potential on the surface of sphere 1.
C) Calculate the potential on the surface of sphere 2.
Answer:
A) V = -136.36 V , B) V = 4.85 10³ V , C) V = 1.62 10⁴ V
Explanation:
To calculate the potential at an external point of the spheres we use Gauss's law that the charge can be considered at the center of the sphere, therefore the potential for an external point is
V = k ∑ [tex]q_{i} / r_{i}[/tex]
where [tex]q_{i}[/tex] and [tex]r_{i}[/tex] are the loads and the point distances.
A) We apply this equation to our case
V = k (q₁ / r₁ + q₂ / r₂)
They ask us for the potential at the midpoint of separation
r = 3.30 / 2 = 1.65 m
this distance is much greater than the radius of the spheres
let's calculate
V = 9 10⁹ (1.1 10⁻⁸ / 1.65 + (-3.6 10⁻⁸) / 1.65)
V = 9 10¹ / 1.65 (1.10 - 3.60)
V = -136.36 V
B) The potential at the surface sphere A
r₂ is the distance of sphere B above the surface of sphere A
r₂ = 3.30 -0.02 = 3.28 m
r₁ = 0.02 m
we calculate
V = 9 10⁹ (1.1 10⁻⁸ / 0.02 - 3.6 10⁻⁸ / 3.28)
V = 9 10¹ (55 - 1,098)
V = 4.85 10³ V
C) The potential on the surface of sphere B
r₂ = 0.02 m
r₁ = 3.3 -0.02 = 3.28 m
V = 9 10⁹ (1.10 10⁻⁸ / 3.28 - 3.6 10⁻⁸ / 0.02)
V = 9 10¹ (0.335 - 180)
V = 1.62 10⁴ V
Three point charges (some positive and some negative) are fixed to the corners of the same square in various ways, as the drawings show. Each charge, no matter what its algebraic sign, has the same magnitude. In which arrangement (if any) does the net electric field at the center of the square have the greatest magnitude?
Answer:
The magnitude of the net field located at the center of the square is the same in every of arrangement of the charges.
"Neon signs need 12,000 V to operate. If a transformer operates off a 240 V source and has 1000 turns in its primary coil, how may turns must the secondary coil have
Answer:
50000 turns
Explanation:
Vp / Vs = Np / Ns
240 / 12000 = 1000 / Ns
Ns = 50000 turns
Assume that a lightning bolt can be represented by a long straight line of current. If 15.0 C of charge passes by in a time of 1.5·10-3s, what is the magnitude of the magnetic field at a distance of 24.0 m from the bolt?
Answer:
The magnitude of the magnetic field is 8.333 x 10⁻⁷ T
Explanation:
Given;
charge on the lightening bolt, C = 15.0 C
time the charge passes by, t = 1.5 x 10⁻³ s
Current, I is calculated as;
I = q / t
I = 15 / 1.5 x 10⁻³
I = 10,000 A
Magnetic field at a distance from the bolt is calculated as;
[tex]B = \frac{\mu_o I}{2\pi r}[/tex]
where;
μ₀ is permeability of free space = 4π x 10⁻⁷
I is the current in the bolt
r is the distance of the magnetic field from the bolt
[tex]B = \frac{\mu_o I}{2\pi r} \\\\B = \frac{4\pi *10^{-7} 10000}{2\pi *24} \\\\B = 8.333 *10^{-5} \ T[/tex]
Therefore, the magnitude of the magnetic field is 8.333 x 10⁻⁷ T
You are fixing a transformer for a toy truck that uses an 8.0-V emf to run it. The primary coil of the transformer is broken; the secondary coil has 40 turns. The primary coil is connected to a 120-V wall outlet.
(a) How many turns should you have in the primary coil?
(b) If you then connect this primary coil to a 240-V source, what emf would be across the secondary coil?
Comments: The relevant equation is N1/N2 = V1/V2 where N is the number of turns and V is the voltage. I'm just not sure how to get the voltage of the secondary coil using emf.
Answer:
a. The primary turns is 60 turns
b. The secondary voltage will be 360 volts.
Explanation:
Given data
secondary turns N2= 40 turns
primary turns N1= ?
primary voltage V1= 120 volts
secondary voltage V2= 8 volts
Applying the transformer formula which is
[tex]\frac{N1}{N2} =\frac{V1}{V2}[/tex]
we can solve for N1 by substituting into the equation above
[tex]\frac{N1}{40} =\frac{120}{8} \\\ N1= \frac{40*120}{8} \\\ N1= \frac{4800}{8} \\\ N1= 60[/tex]
the primary turns is 60 turns
If the primary voltage is V1 240 volts hence the secondary voltage V2 will be (to get the voltage of the secondary coil using emf substitute the values of the previously gotten N1 and N2 using V1 as 240 volts)
[tex]\frac{40}{60} =\frac{240}{V2}\\\\V2= \frac{60*240}{40} \\\\V2=\frac{ 14400}{40} \\\\V2= 360[/tex]
the secondary voltage will be 360 volts.
(a) In the primary coil, you have "60 turns".
(b) The emf across the secondary coil would be "360 volts".
Transformer and VoltageAccording to the question,
Primary voltage, V₁ = 120 volts
Secondary voltage, V₂ = 8 volts
Secondary turns, N₂ = 40 turns
(a) By applying transformer formula,
→ [tex]\frac{N_1}{N_2} = \frac{V_1}{V_2}[/tex]
or,
N₁ = [tex]\frac{N_2\times V_1}{V_2}[/tex]
By substituting the values,
= [tex]\frac{40\times 120}{8}[/tex]
= [tex]\frac{4800}{8}[/tex]
= 60
(2) Again by using the above formula,
→ V₂ = [tex]\frac{60\times 240}{40}[/tex]
= [tex]\frac{14400}{40}[/tex]
= 360 volts.
Thus the above approach is correct.
Find out more information about voltage here:
https://brainly.com/question/4389563
Two positive charges are located at x = 0, y = 0.3m and x = 0, y = -.3m respectively. Third point charge q3 = 4.0 μC is located at x = 0.4 m, y = 0.
A) Make a careful sketch of decent size that illustrates all force vectors with directions and magnitudes.
B) What is the resulting vector of the total force on charge q1 exerted by the other two charges using vector algebra?
Answer:
0.46N
Explanation:
See attached file
Experts, ACE, Genius... can anybody calculate for the Reactions at supports A and B please? Will give brainliest! Given: fb = 300 kN/m, fc = 100 kN/m, Dy = 300 kN, spanAB = 6m, span BC = 6m, spanCD = 6m
Answer:
Support at Cy = 1.3 x 10³ k-N
Support at Ay = 200 k-N
Explanation:
given:
fb = 300 k-N/m
fc = 100 k-N/m
D = 300 k-N
L ab = 6 m
L bc = 6 m
L cd = 6 m
To get the reaction A or C.
take summation of moment either A or C.
Support Cy:
∑ M at Ay = 0
(( x1 * F ) + ( D * Lab ) + ( D * L bc + D * L cd )
Cy = -------------------------------------------------------------------
( L ab + L bc )
Cy = 1.3 x 10³ k-N
Support Ay:
Since ∑ F = 0, A + C - F - D = 0
A = F + D - C
Ay = 200 k-N
Answer:
i was going to but its to late
Explanation:
A Young'sdouble-slit interference experiment is performed with monochromatic light. The separation between the slits is 0.44 mm. The interference pattern on the screen 4.2 m away shows the first maximum 5.5 mm from the center of the pattern. What is the wavelength of the light in nm
Answer:
Explanation:
The double slit interference phonemene is described for the case of constructive interference
d sin θ= m λ (1)
let's use trigonometry to find the sinus
tan θ = y / L
in general in interference phenomena the angles are small
tan θ = sin θ / cos θ = sin θ
The double slit interference phonemene is described for the case of constructive interference
d sin θ = m lam (1)
let's use trigonometry to find the sinus
tan θ = y / L
in general in interference phenomena the angles are small
tan θ = sin θ / cos θ = sin θ
we substitute
sin θ = y / L
we substitute in equation 1
d y / L = m λ
λ = dy / L m
let's reduce the magnitudes to the SI system
d = 0.44 mm = 0.44 10⁻³ m
y = 5.5 mm = 5.5 10⁻³ m
L = 4.2m
m = 1
let's calculate
λ = 0.44 10⁻³ 5.5 10⁻³ / (4.2 1)
λ = 5.76190 10-7 m
let's reduce to num
lam = 5.56190 10-7 m (109 nm / 1m)
lam = 556,190 nmtea
we substitute
without tea = y / L
we substitute in equation 1
d y / L = m lam
lam = dy / L m
let's reduce the magnitudes to the SI system
d = 0.44 me = 0.44 10-3 m
y = 5.5 mm = 5.5 10-3
L = 4.2m
m = 1
let's calculate
lam = 0.44 10⁻³ 5.5 10⁻³ / (4.2 1)
lam = 5.76190 10⁻⁷ m
let's reduce to num
lam = 5.56190 10⁻⁷ m (109 nm / 1m)
lam = 556,190 nm
if a speed sound in air at o°c is 331m/s. what will be its value at 35 °c
Answer:
please brainliest!!!
Explanation:
V1/√T1 =V2/√T2
V1 = 331m/s
T1 = 0°C = 273k
V2 = ?
T2 = 35°c = 308k
331/√273 = V2/√308331/16.5 = V2/17.520.06 = V2/17.5V2 = 20.06 x 17.5 V2 = 351.05m/sTo work on your car at night, you use an extension cord to connect your work light to a power outlet near the door. How would the illumination provided by the light be affected by the length of the extension cord
Answer:
The longer the cord, the lower the illumination
Explanation:
The illumination provided by the light bulb will be reduced as the length of the extension cord increases. This is because the resistance provided by the wire increases with its length.
Long wires have more electrical resistance than shorter ones.
Let us consider this formula:
Resistance =[tex]\frac{\rho L}{A}[/tex]
From this formula, we can see that as the length increases, the resistance to current flow offered by the wire increases also provided the resistivity and cross-sectional area of the wire remain constant. As a result of this, the illumination will drop.
dandre expands 120w of power in moving a couch 15 meters in 5 seconds how much force does he exert ?
Answer:
The answer is 40 N for APX
Explanation:
what is the mass of an oil drop having two extra electrons that is suspended motionless by the field between the plates
Answer:
m = 3,265 10⁻²⁰ E
Explanation:
For this exercise we can use Newton's second law applied to our system, which consists of a capacitor that creates the uniform electric field and the drop of oil with two extra electrons.
∑ F = 0
[tex]F_{e}[/tex] - W = 0
the electric force is
F_{e} = q E
as they indicate that the charge is two electrons
F_{e} = 2e E
The weight is given by the relationship
W = mg
we substitute in the first equation
2e E = m g
m = 2e E / g
let's put the value of the constants
m = (2 1.6 10⁻¹⁹ / 9.80) E
m = 3,265 10⁻²⁰ E
The value of the electric field if it is a theoretical problem must be given and if it is an experiment it can be calculated with measures of the spacing between plates and the applied voltage, so that the system is in equilibrium
Zack is driving past his house. He wants to toss his physics book out the window and have it land in his driveway. If he lets go of the book exactly as he passes the end of the driveway. Should he direct his throw outward and toward the front of the car (throw 1), straight outward (throw 2), or outward and toward the back of the car (throw 3)? Explain.
Answer:
Zack should direct his throw outward and toward the back of the car.
Explanation:
As the car is moving forward, the book will be thrown with a forward component. Therefore, throwing this book backwards at a constant speed would cancel the motion of the car, allowing the book to have a greater chance of ending on the driveway. I say a greater chance as Zack may not have the exact timings as to land the book in his driveway. That too he may not have thrown the book with the right momentum.
The solution is throw 3.
I say a greater chance as Zack may not have the exact timings as to land the book in his driveway. That too he may not have thrown the book with the right momentum as the skydivers.
Which statement best applies Newton’s laws of motion?The statement that best applies Newton’s laws of motion to explain the skydiver’s motion is that an upward force balances the downward force of gravity on the skydiver. Newton's 3rd law often applies to skydiving.
When gravity is not acting upon the skydivers they would continue moving in the direction the vehicle they jumped from was moving. If no air resistance takes place, then the skydivers would still accelerating at 9.8 m/s until they hit the ground.
The skydiver after leaving the aircraft will accelerates downwards due to the force of gravity usually as there is no air resistance acting in the upwards direction, and there is a resultant force acting downwards, the skydiver will accelerates towards the ground.
Therefore, I say a greater chance as Zack may not have the exact timings as to land the book in his driveway. That too he may not have thrown the book with the right momentum as the skydivers.
Learn more about skydiver on:
https://brainly.com/question/29253407
#SPJ6
On a part-time job, you are asked to bring a cylindrical iron rod of density 7800 kg/m 3 kg/m3 , length 81.2 cmcm and diameter 2.60 cmcm from a storage room to a machinist. Calculate the weight of the rod, www. Assume the free-fall acceleration is ggg = 9.80 m/s2m/s2 .
Answer:
The weight of the rod is 32.87 N
Explanation:
Density of the rod = 7800 kg/m
length of the rod = 81.2 cm = 0.812 m
diameter of rod = 2.60 cm = 0.026 m
acceleration due to gravity = 9.80 m/s^2
The rod can be assumed to be a cylinder.
The volume of the rod can be calculated as that of a cylinder, and can be gotten as
V = [tex]\frac{\pi d^{2} l}{4}[/tex]
where d is the diameter of the rod
l is the length of the rod
V = [tex]\frac{3.142* 0.026^{2}* 0.812}{4}[/tex] = 4.3 x 10^-4 m^3
We know that the mass of a substance is the density times the volume i.e
mass m = ρV
where ρ is the density of the rod
V is the volume of the rod
m = 4.3 x 10^-4 x 7800 = 3.354 kg
The weight of a substance is the mass times the acceleration due to gravity
W = mg
where g is the acceleration due to gravity g = 9.80 m/s^2
The weight of the rod W = 3.354 x 9.80 = 32.87 N
A force acting on an object moving along the x axis is given by Fx = (14x - 3.0x2) N where x is in m. How much work is done by this force as the object moves from x = -1 m to x = +2 m?
Answer:
72J
Explanation:
distance moved is equal to 3m.then just substitute x with 3m.
Fx = (14(3) - 3.0(3)2)) N
Fx =(42-18)N
Fx =24N
W=Fx *S
W=24N*3m
W=72J
The answer is 72J.
Distance moved is equal to 3m.
Then just substitute x with 3m.
Fx = (14(3) - 3.0(3)2)) N
Fx =(42-18)N
Fx =24N
W=Fx *S
W=24N*3m
W=72J
Is there any definition of force?A force is a push or pulls upon an object resulting from the object's interaction with another object. Whenever there is an interaction between two objects, there is a force upon each of the objects.
Learn more about force here https://brainly.com/question/25239010
#SPJ2
An astronaut out on a spacewalk to construct a new section of the International Space Station walks with a constant velocity of 2.30 m/s on a flat sheet of metal placed on a flat, frictionless, horizontal honeycomb surface linking the two parts of the station. The mass of the astronaut is 71.0 kg, and the mass of the sheet of metal is 230 kg. (Assume that the given velocity is relative to the flat sheet.)
Required:
a. What is the velocity of the metal sheet relative to the honeycomb surface?
b. What is the speed of the astronaut relative to the honeycomb surface?
Answer:
Explanation:
Let the velocity of astronaut be u and the velocity of flat sheet of metal plate be v . They will move in opposite direction , so their relative velocity
= u + v = 2.3 m /s ( given )
We shall apply conservation of momentum law for the movement of astronaut and metal plate
mu = M v where m is mass of astronaut , M is mass of metal plate
71 u = 230 x v
71 ( 2.3 - v ) = 230 v
163.3 = 301 v
v = .54 m / s
u = 1.76 m / s
honeycomb will be at rest because honeycomb surface is frictionless . Plate will slip over it . Over plate astronaut is walking .
a ) velocity of metal sheet relative to honeycomb will be - 1.76 m /s
b ) velocity of astronaut relative to honeycomb will be + .54 m /s
Here + ve direction is assumed to be the direction of astronaut .
A record player rotates a record at 45 revolutions per minute. When the record player is switched off, it makes 4.0 complete turns at a constant angular acceleration before coming to rest. What was the magnitude of the angular acceleration (in rads/s2) of the record as it slowed down
Answer:
The angular acceleration is [tex]\alpha = 0.4418 \ rad /s^2[/tex]
Explanation:
From the question we are told that
The angular speed is [tex]w_f = 45 \ rev / minutes = \frac{45 * 2 * \pi }{60 }= 4.713 \ rad/s[/tex]
The angular displacement is [tex]\theta =4 \ rev = 4 * 2 * \pi = 25.14 \ rad[/tex]
From the first equation of motion we can define the movement of the record as
[tex]w_f ^2 = w_o ^2 + 2 * \alpha * \theta[/tex]
Given that the record started from rest [tex]w_o = 0[/tex]
So
[tex]4.713^2 = 2 * \alpha * 25.14[/tex]
[tex]\alpha = 0.4418 \ rad /s^2[/tex]
An appliance with a 20.0-2 resistor has a power rating of 15.0 W. Find the maximum current which can flow safely through the appliance g
Q: An appliance with a 20 Ω resistor has a power rating of 15.0 W. Find the maximum current which can flow safely through the appliance g
Answer:
0.866 A
Explanation:
From the question,
P = I²R............................. Equation 1
Where P = power, I = maximum current, R = Resistance.
Make I the subject of the equation
I = √(P/R).................... Equation 2
Given: P = 15 W, R = 20 Ω
Substitute these values into equation 2
I = √(15/20)
I = √(0.75)
I = 0.866 A
Hence the maximum current that can flow safely through the appliance = 0.866 A
A wooden artifact from a Chinese temple has a 14C activity of 41.0 counts per minute as compared with an activity of 58.2 counts per minute for a standard of zero age. You may want to reference (Pages 913 - 916) Section 21.4 while completing this problem. Part A From the half-life for 14C decay, 5715 yr, determine the age of the artifact. Express your answer using two significant figures. t
Answer:
Explanation:
The relation between activity and number of radioactive atom in the sample is as follows
dN / dt = λ N where λ is disintegration constant and N is number of radioactive atoms
For the beginning period
dN₀ / dt = λ N₀
58.2 = λ N₀
similarly
41 = λ N
dividing
58.2 / 41 = N₀ / N
N = N₀ x .70446
formula of radioactive decay
[tex]N=N_0e^{-\lambda t }[/tex]
[tex].70446 =e^{-\lambda t }[/tex]
- λ t = ln .70446 = - .35
t = .35 / λ
λ = .693 / half life
= .693 / 5715
= .00012126
t = .35 / .00012126
= 2886.36
= 2900 years ( rounding it in two significant figures )
As light shines from air to another medium, i = 26.0 º. The light bends toward the normal and refracts at 32.0 º. What is the index of refraction? A. 1.06 B. 0.944 C. 0.827 D. 1.21
Explanation:
It is given that,
Angle of incidence from air to another medium, i = 26°
The angle of reflection, r = 32°
We need to find the refractive index of the medium. The ratio of sine of angle of incidence to the sine of angle of reflection is called refractive index. It can be given by :
[tex]n=\dfrac{\sin i}{\sin r}\\\\n=\dfrac{\sin (26)}{\sin (32)}\\\\n=0.82[/tex]
So, the index of refraction is 0.82. Hence, the correct option is C.
A tennis player swings her 1000 g racket with a speed of 12 m/s. She hits a 60 g tennis ball that was approaching her at a speed of 15 m/s. The ball rebounds at 40 m/s.
A) How fast is her racket moving immediately after the impact? You can ignore the interaction of the racket with her hand for the brief duration of the collision.
_________m/s
B) If the tennis ball and racket are in contact for 7.00, what is the average force that the racket exerts on the ball?
_________N
The velocity and force are required.
The speed of the racket is 8.7 m/s
The required force is 471.43 N.
[tex]m_1[/tex] = Mass of racket = 1000 g
[tex]m_2[/tex] = Mass of ball = 60 g
[tex]u_1[/tex] = Initial velocity of racket = 12 m/s
[tex]u_2[/tex] = Initial velocity of ball = -15 m/s
[tex]v_1[/tex] = Final velocity of racket
[tex]v_2[/tex] = Final velocity of ball = 40 m/s
[tex]\Delta t[/tex] = Time = 7 ms
The equation of the momentum will be
[tex]m_1u_1+m_2u_2=m_1v_1+m_2v_2\\\Rightarrow v_1=\dfrac{m_1u_1+m_2u_2-m_2v_2}{m_1}\\\Rightarrow v_1=\dfrac{1\times 12+0.06\times (-15)-0.06\times 40}{1}\\\Rightarrow v_1=8.7\ \text{m/s}[/tex]
Force is given by
[tex]F=m_2\dfrac{v_2-u_2}{\Delta t}\\\Rightarrow F=0.06\times \dfrac{40-(-15)}{7\times 10^{-3}}\\\Rightarrow F=471.43\ \text{N}[/tex]
Learn more:
https://brainly.com/question/19689434?referrer=searchResults
A Young's interference experiment is performed with blue-green laser light. The separation between the slits is 0.500 mm, and the screen is located 3.10 m from the slits. The first bright fringe is located 3.22 mm from the center of the interference pattern. What is the wavelength of the laser light?
Answer:
λ = 5.2 x 10⁻⁷ m = 520 nm
Explanation:
From Young's Double Slit Experiment, we know the following formula for the distance between consecutive bright fringes:
Δx = λL/d
where,
Δx = fringe spacing = distance of 1st bright fringe from center = 0.00322 m
L = Distance between slits and screen = 3.1 m
d = Separation between slits = 0.0005 m
λ = wavelength of light = ?
Therefore,
0.00322 m = λ(3.1 m)/(0.0005 m)
λ = (0.00322 m)(0.0005 m)/(3.1 m)
λ = 5.2 x 10⁻⁷ m = 520 nm
What is the requirement for the photoelectric effect? Select one: a. The incident light must have enough intensity b. The incident light must have a wavelength shorter than visible light c. The incident light must have at least as much energy as the electron work function d. Both b and c
Answer:
c. The incident light must have at least as much energy as the electron work function
Explanation:
In photoelectric effect, electrons are emitted from a metal surface when a light ray or photon strikes it. An electron either absorbs one whole photon or it absorbs none. After absorbing a photon, an electron either leaves the surface of metal or dissipate its energy within the metal in such a short time interval that it has almost no chance to absorb a second photon. An increase in intensity of light source simply increase the number of photons and thus, the number of electrons, but the energy of electron remains same. However, increase in frequency of light increases the energy of photons and hence, the
energy of electrons too.
Therefore, the energy of photon decides whether the electron shall be emitted or not. The minimum energy required to eject an electron from the metal surface, i.e. to overcome the binding force of the nucleus is called ‘Work Function’
Hence, the correct option is:
c. The incident light must have at least as much energy as the electron work function
What is the change in internal energy of the system (∆U) in a process in which 10 kJ of heat energy is absorbed by the system and 70 kJ of work is done by the system?
Answer:
Explanation:
According to first law of thermodynamics:
∆U= q + w
= 10kj+(-70kJ)
-60kJ
, w = + 70 kJ
(work done on the system is positive)
q = -10kJ ( heat is given out, so negative)
∆U = -10 + (+70) = +60 kJ
Thus, the internal energy of the system decreases by 60 kJ.
Unpolarized light passes through a vertical polarizing filter, emerging with an intensity I0. The light then passes through a horizontal filter, which blocks all of the light; the intensity transmitted through the pair of filters is zero. Suppose a third polarizer with axis 45 ? from vertical is inserted between the first two.
What is the transmitted intensity now?
Express your answer in terms of I0. I got I0/8. But this is not right. I guess they want a number?
Answer:
I₂ = 0.25 I₀
Explanation:
To know the light transmitted by a filter we must use the law of Malus
I = I₀ cos² θ
In this case, the intensity of the light that passes through the first polarizer is I₀, it reaches the second polarized, which is at 45⁰, therefore the intensity I1 comes out of it.
I₁ = I₀ cos² 45
I₁ = I₀ 0.5
this is the light that reaches the third polarizer, which is at 45⁰ with respect to the second, from this comes the intensity I₂
I₂ = I₁ cos² 45
I₂ = (I₀ 0.5) 0.5
I₂ = 0.25 I₀
this is the intensity of the light transmitted by the set of polarizers
The copper wire to the motor is 6.0 mm in diameter and 1.1 m long. How far doesan individual electron travel along the wire while the starter motor is on for asingle start of the internal combustion engine
Answer:
0.306mm
Explanation:
The radius of the conductor is 3mm, or 0.003m
The area of the conductor is:
A = π*r^2 = π*(.003)^2 = 2.8*10^-5 m^2
The current density is:
J = 130/2.8*10^-5 = 4.64*10^6 A/m
According to the listed reference:
Vd = J/(n*e) = 4.64*10^6 / ( 8.46*10^28 * 1.6*10^-19 ) = 0.34*10^-6 m/s = 0.34mm/s
The distance traveled is:
x = v*t = 0.34 * .90 = 0.306 mm
What is the minimum magnitude of an electric field that balances the weight of a plasticsphere of mass 5.4 g that has been charged to -3.0 nC
Answer:
E = 17.64 x 10⁶ N/C = 17.64 MN/C
Explanation:
The electric field is given by the following formula:
E = F/q
E= W/q
E = mg/q
where,
E = magnitude of electric field = ?
m = mass of plastic sphere = 5.4 g = 5.4 x 10⁻³ kg
g = acceleration due to gravity = 9.8 m/s²
= charge = 3 nC = 3 x 10⁻⁹ C
Therefore,
E = (5.4 x 10⁻³ kg)(9.8 m/s²)/(3 x 10⁻⁹ C)
E = 17.64 x 10⁶ N/C = 17.64 MN/C
Will give brainliest ASAP! Please help (1/10 questions, will mark 5 stars and brainliest for all answers if correct)
Answer:
Option (A)
Explanation:
A 20 kg boy chases the butterfly with a speed of 2 meter per second.
Angle at which he runs is 70° North of West.
Therefore, Horizontal component (Vx) directing towards West will be,
Vx = v(Cos70°)
Vy = v(Sin70°)
Since momentum of a body is defined by,
Momentum = Mass × Velocity
Therefore, Westerly component of the momentum will be,
Momentum = 20 × (v)(Cos70°)
= 20 × 2Cos70°
= 13.68
≈ 13.7 kg-meter per second
Therefore, Option (A) will be the answer.
21. What is the most likely outcome of decreasing the frequency of incident light on a diffraction grating?
A. lines become narrower
B. distance between lines increases
C. lines become thicker
D. distance between lines decreases
Answer:
B.distance between lines increases
Answer:
A. Lines become narrower
Explanation:
I got it right on my quiz!
I hope this helps!! :))