a smart phone charger delivers charge to the phone, in the form of electrons, at a rate of -0.75 c/s .how many electrons are delivered to the phone during 23 min of charging?

A skier with mass of 62 kg is sliding down a snowy slope. The coefficient of kinetic friction is 0.0738 N

The coefficient of kinetic friction can be found using the formula:

Friction = coefficient of kinetic friction × Normal force

We know that the friction force is 45 N and the normal force is equal to the skier's weight, which can be found using the formula

Weight = mass × gravity

Where the mass is 62 kg and the acceleration due to gravity is approximately :9.8 m/s²

So the normal force is: 62 kg × 9.8 = 607.6 N

Therefore, the coefficient of kinetic friction is: Friction / Normal force  or approximately

= [tex]\frac{45}{607.6}[/tex] = 0.0738

The force that opposes the motion of two surfaces in contact as they slide against one another is known as kinetic friction, but other names for it include sliding friction and dynamic friction. The properties of the two surfaces in contact, such as the roughness of their surfaces and the materials they are made of, determine its strength. It acts in the opposite direction of the force applied to an object.

To know more about force :

brainly.com/question/13191643

#SPJ4

The refractive index of the glass is 1.16, if the thickness of the glass slab is 2.25 cm, and the diameter of the circle is 7.60 cm.

incident angle of the light,θ = 90°

Let the angle of internal refraction is θ₁

Let the refractive index of the glass slab, = μ₁

Refractive index of vacuum, μ₂ = 1

By Snell's law, μ₁sinθ₁ = μ₂sin90

Radius of the circle, R = 7.6/2 = 3.8 cm

Thickness of the slab, and radius of the circle, R, makes the right angle triangle with hypotenuse(AC). So applying the pythagorus theorem,

AC² = 2.25² + 3.8²

AC = √(2.25² + 3.8²)

AC = 4.42

So sinθ₁ = 3.8/4.42

sinθ₁ = 0.86

μ₁ × 0.86 = μ₂×sin90

μ₁ × 0.86 = 1 × 1

μ₁ = 1/0.86

μ₁ = 1.16

So the refractive index of the glass slab, μ₁ = 1.16

To know more about refractive index, here

https://brainly.com/question/23750645

#SPJ4

The average speed of a helium atom at a certain temperature is 1100 m/s expressed in miles per hour is: 2460.63 mi/h

It is the transformation of a value expressed in one unit of measurement into an equivalent value expressed in another unit of measurement of the same nature.

To solve this problem the we have to convert the units with the given information.

Information about the problem:

By converting the speed units from (m/s) to (mi/h) we have:

v= 1100 m/s * 1 mi/1609.34 m * 3600 s/1 h

v= 2460.63 mi/h

Learn more about unit conversion at: brainly.com/question/141163

#SPJ4

The angular velocity of the rider is 2.9 rad/s. The result is obtained by using the formulas in circular motion.

Circular motion is a motion of an object along a circular path. When an object moves with an acceleration, it has a centripetal acceleration calculated by

ac = v²/r

Where

In circular motion, an object moves with linear and angular velocity. The relationship between both velocities is

v = ωr

Where

A rider moves in a circular motion with

Find the angular velocity! (ω = ?)

We find the centripetal acceleration in m/s².

ac = 10.5g

ac = 10.5 × 9.8 m/s²

ac = 102.9 m/s²

The linear velocity is

ac = v²/r

102.9 = v²/12.5

v² = 102.9 × 12.5

v² = 1,286.25

v ≈ 35.9 m/s

Use the equation of relationship between linear and angular velocity!

v = ωr

35.9 = ω (12.5)

ω ≈ 2.9 rad/s

Hence, the rider has the angular velocity of 2.9 rad/s.

Learn more about angular velocity here:

brainly.com/question/14769426

#SPJ4

The momentum of the object afterwards will be 80 Kgms-1.

Given the following data as per the question:

Mass of the object is given as 6 Kg

Force is given as 10 N in the question

Time is given as the following 8 sec

The value of the Momentum is same as impulse.

So, the formula of impulse is given as:

I = Ft

Where

I is the impulse

F is the force

and t is the time

From the given information,

F = 10 N

t = 8 secs

Therefore,

I = 10 × 8

I = 80 Ns.

Momentum is 80 Kgms-1.

Learn more about momentum:

brainly.com/question/29598011

#SPJ4

The final velocity of the composite object after collision is 1.8002 m/s in the direction of the first object.

Initial velocity of the first object, v₁ = 5.001 m/s

Mass of the first object, m₁ = 3.0 kg

Initial velocity of the second object, v₂ = -3.001 m/s (In opposite direction)

Mass of the second object, m₂ = 2.0 kg

Let the final velocity of the composite object, = V

Mass of the composite object, = (3.0 + 2.0) = 5.0 kg

By the law of conservation of momentum,

m₁v₁ + m₂v₂ = (m₁ + m₂) × V

V = (m₁v₁ + m₂v₂)/(m₁ + m₂)

V = (3 × 5.001 + 2 × (-3.001))/(2 + 3)

V = 9.001/5

V = +1.8006 m/s

Positive sign indicates that the direction of the velocity will be the same as that of the first object.

To know more about velocity, here

https://brainly.com/question/28738284

#SPJ4

The speed of the car traveling when it went over the cliff is 38.12 m/s.

The equation of motion for calculating the displacement of a moving object is given as

                                           [tex]S = ut + \frac{1}{2} at^{2}[/tex]

u = initial velocity

t = time taken

a = acceleration of the object

S = displacement of the object

The above equation can be used to find out the speed of the car.

        Therefore, the above equation can be written as

                                               [tex]h = \frac{1}{2} gt^{2}\\t = \sqrt[]{\frac{2h}{g} } \\t = \sqrt[]{\frac{2(57)}{9.8} } \\\\t = 3.41 s[/tex]

Therefore, the time of flight = 3.41 s.

If the point of impact from the base of the cliff is 130 m and the time of flight is 3.41 s.

Then, the velocity of the car traveling over the cliff is calculated as

                                            [tex]v = \frac{point of impact}{t} \\\\v = \frac{130}{3.41} \\\\v = 38.12 m/s[/tex]

The velocity of the car traveling when it went over the cliff is 38.12 m/s.

To know more about displacement equations, visit: https://brainly.com/question/248054

#SPJ4

If an object is traveling in a circular orbit where its speed is doubled, then its centripetal acceleration will be quadrupled.

Centripetal acceleration is the acceleration of an object traversing a circular path. Because velocity is a vector quantity, i.e., it has both a magnitude ( the speed and a direction), so when the object travels on a circular path, its direction changes constantly and thus as a result of this its velocity changes, producing acceleration,

For instance, when an object in a circular orbit is moved with double doubled, then it has quadrupled centripetal acceleration.

You can learn more about Centripetal acceleration at

https://brainly.com/question/79801

#SPJ4

Answer : Original Speed is 6m/s while acceleration is 0.3m/s^2.

What is speed?

--In everyday use and in kinematics, the speed of an object is the magnitude of the change of its position over time or the magnitude of the change of its position per unit of time;

-- it is thus a scalar quantity.

Here in this question we have given final speed , we have to find the intial speed as well as the acceleration of the body.

d = V1 + V2 /2 × t

45 = V1 + 3/2 × 10

V1 = 6 m/s.

Hence initial speed of body is 6m/s .

By using first equation of motion we find the acceleration

we get acceleration is 0.3 .

What is velocity?

-- Velocity is the directional speed of an object in motion as an indication of its rate of change in position as observed from a particular frame of reference and as measured by a particular standard of time .

Learn more about acceleration from https://brainly.com/question/605631.

#SPJ4

The work that has been done by the Korbel is  4.41kJ.

We have to note that we define work in physics as the product of the force and the distance. In the case of the chair in the question, we have been told that Korbel pushes a 15 kg chair for a distance of 30 meters.

The force in this case would be the weight of the chair that we have and we can write that;

W = mgh

m = mass

g = acceleration due to gravity

h = height

Thus

W = 15 * 9.8 * 30

W = 4.41kJ

Thus a work of about  4.41kJ is done.

Learn more about work done:https://brainly.com/question/13662169

#SPJ1

The gravitational acceleration of this new planet is [tex]24.3 * 10^{9} G m/s^{2}[/tex].

                                        g = GM/R^2

Here,

G = the universal gravitational constant (G = gravitational constant of planet)

M = Mass of planet = [tex]3.5*10^{31} kg[/tex]

R = Radius = 1.2*10^11 m

Putting these values in above equation we get: g=  [tex]24.3 * 10^{9} G m/s^{2}[/tex].

To know more about gravity visit:

https://brainly.com/question/30186613

#SPJ4

Due to the satellite's overshooting circular course and movement away from Earth against the pull of gravity, the speed of satellite in such a closed circular orbit would be greater than 8 km/s.

The direction of gravity always seems to be toward the core of the Earth when a satellite travels around it in a circular orbit.

Thus, due to the satellite's overshooting circular course and movement away from Earth against the pull of gravity, the speed of satellite in such a closed circular orbit would be greater than 8 km/s.

To know more about the pull of gravity, here

https://brainly.com/question/28854345

#SPJ4

The magnitude of the acceleration is |8.1 * 10^5| m/s^2 = 8.1 * 10^5 m/s^2

In mechanics, rate of change of velocity of an object with respect to the time is called as acceleration.

As it is known, F = k * (q1 * q2)/r^2

where F is force, k is Coulomb's constant (9 x 10^9 N * m^2/C^2), q1 and q2 are charges of the two spheres, and r is distance between the two spheres.

As we know that , F = m * a

a = F/m

a = (k * (q1 * q2))/r^2) / m

a = (9 * 10^9 N * m^2/C^2 * (-23 * 10^-9 C)^2) / (10^-2 m)^2

Acceleration of the upper sphere is a = -8.1 * 10^5 m/s^2. The negative sign indicates that acceleration is in opposite direction to the force, as expected, since the force is repulsive.

The magnitude of the acceleration is |8.1 * 10^5| m/s^2 = 8.1 * 10^5 m/s^2

To know more about acceleration, refer

https://brainly.com/question/460763

#SPJ4

After 150 seconds, the rocket is moving at a velocity of 32700 m/s and has traveled 1,623,500 meters.

A constant acceleration is a change in velocity that does not change over time. If a car accelerates by 20 mph one minute and then another 20 mph the next, its average acceleration remains constant at 20 mph per minute.

We can use the equations of motion to calculate the speed and distance traveled of the rocket. The equation for velocity as a function of time is:

v = at

where v is the velocity, a is the acceleration, and t is the time. Substituting in the given values, we get:

v = 218 m/s * 150 s = 32700 m/s

To find the distance traveled, we can use the equation:

d = 1/2 * at^2

Substituting in the given values, we get:

d = 1/2 * 218 m/s^2 * 150 s^2 = 1,623,500 m

So after 150 seconds, the rocket is moving at a velocity of 32700 m/s and has traveled 1,623,500 meters.

Learn more about velocity here:

https://brainly.com/question/18084516

#SPJ4

Net work the engine perform during the cycle is b) 330 J.

The net work done by a heat engine is the difference between the heat absorbed by the engine and the heat exhausted. Therefore, the net work done by the engine during a cycle is

1240 J - 910 J = 330 J.

How does the temperature of the hot reservoir affect the efficiency of a heat engine?

The efficiency of a heat engine is directly related to the temperature of the hot reservoir. The higher the temperature of the hot reservoir, the more thermal energy is available for conversion into work. This means that the efficiency of the heat engine increases as the temperature of the hot reservoir increases. The maximum efficiency of a heat engine is given by the Carnot efficiency, which is only achievable when the temperature of the cold reservoir is 0 K (absolute zero) and the temperature of the hot reservoir is infinite.

To know more about cold reservoir visit:

brainly.com/question/14142895

#SPJ4

Answer:

Explanation:

I think it is the top one as the formula for density is d = M/V, where d is density, M is mass, and V is volume. Density is commonly expressed in units of grams per cubic centimetre.

But I'm not 100% sure

The point where the potential is zero is located at [tex]x = 5 cm * k * Q1/(Q1 + Q2)[/tex]

The potential at a point in space due to a point charge is given by the equation:

V = k * Q/r

where V is the potential, k is the Coulomb constant  [tex](8.99 x 10^9 N * m^2/C^2)[/tex], Q is the charge, and r is the distance from the point charge to the point where the potential is being calculated.

In this problem, we have two point charges placed 5 cm apart on the x-axis. How about we call the charges Q1 and Q2, and we should assume that Q1 is located at the origin (x = 0) and Q2 is located at x = 5 cm.

The potential at a point along the x-axis is the amount of the potentials due to each of the point charges.

V = k * Q1/r1 + k * Q2/r2

where r1 is the distance from the point to Q1 and r2 is the distance from the point to Q2.

In the event that the potential at a point is zero, the amount of the potential due to each of the point charges is zero.

So, k * Q1/r1 + k * Q2/r2 = 0

To find the points along the x-axis where the potential is zero, we can set the equation above equal to zero and address for x.

r1 = x and r2 = |x - 5 cm|

k * Q1/x + k * Q2/|x - 5 cm| = 0

x = k * Q1/Q2 * |x - 5 cm|

x = k * Q1 * (5 cm - x)/Q2

x = 5 cm * k * Q1/(Q1 + Q2)

In this way, the point where the potential is zero is located at

x = 5 cm * k * Q1/(Q1 + Q2)

This is valid for any point in the x-axis, and these points are called equipotential points.

To learn more about equipotential points:

https://brainly.com/question/13266693

#SPJ4

The spacing between successive maxima near the center fringe for light of wavelength 500. nm, when l is 1.00 m and d is 1.00 cm is 510^-7 m, Yes, observe the interference of light, distance between the slits be placed for the maxima to be separated by 1.00 mm is 0.5 mm.

Wavelength is a measure of the distance between consecutive peaks (or troughs) of a wave, such as a sound wave or an electromagnetic wave (like light). It is typically measured in meters (m) or nanometers (nm). The wavelength of a wave determines its color, with shorter wavelengths appearing as blue or violet and longer wavelengths appearing as red. In the case of electromagnetic waves, the wavelength also determines the type of radiation, such as radio waves, microwaves, infrared, visible light, ultraviolet, X-rays, and gamma rays.

(a) The spacing between successive maxima near the center fringe for light of wavelength 500 nm is given by the formula dsin(θ) = (λ)/d.

Plugging in the given values, we get: dsin(θ) = [tex]\frac{50010^{-91} }{0.01} =510^{-7} m[/tex]

(b) Yes, it would be possible to observe the interference pattern on the screen for this situation.

(c) To find the distance between the slits, we use the same formula and solve for d: d = (λ)/(dsin(θ)) = [tex]\frac{50010^{-91} }{1*10^{-3} } =0.5mm[/tex]

The slits should be placed 0.5 mm apart to have the maxima separated by 1.00 mm for this wavelength and screen distance.

To know more about distance visit:

https://brainly.com/question/15172156

#SPJ4

Only about 40 percent of the thermal energy in coal is converted to electricity, so the electricity generated per ton of coal is 0.4 x 6,150 kWh or 2,460 kWh/ .

Define  natural gas?

To learn more about watt refers to:

https://brainly.com/question/26918459

#SPJ4

To maintain an exposure level equivalent to f/16 at 1/30 of a second, the new stop should be f/5.6. Due to their inverse relationship, the aperture and shutter speed must be adjusted to account for changes in either one by photographer.

When the shutter speed is increased from 1/30 of a second to 1/500 of a second, the aperture must likewise be changed in order to keep the same exposure level. The amount of light entering the camera, which is managed by the aperture and shutter speed, determines the exposure level. The "exposure triangle" describes the connection between aperture, shutter speed, and exposure. The "reciprocal rule," which dictates that if the shutter speed is increased by a factor of 16, the aperture should be reduced by a factor of 4, should be followed by the photographer in order to maintain the same exposure level. In this instance, the new stop should be f/4 since the photographer wishes to raise the shutter speed from 1/30 to 1/500 while maintaining the same exposure level.

learn more about photographer here:

https://brainly.com/question/25379778

#SPJ4

The component of robot which helps detect the change in environment is a sensor. The correct option is A.

Robotics is the study area devoted to creating robots and automation, while a robot is a programmable machine that can execute a task. Different robots have varying degrees of autonomy. These levels range from totally autonomous bots that operate independently to bots that are controlled by humans and accomplish tasks.

Robots consist of some sort of mechanical construction. The mechanical part of a robot helps it perform tasks in the environment for which it was designed.

Robots have some degree of computer programming. If a robot didn't have a set of instructions telling it what to perform, it would just be another piece of simple hardware. Programming a robot can teach it when and how to perform a task.

To know more about robots:

https://brainly.com/question/28334981

#SPJ4

when 300 waves pass a point in one minute, the frequency is 5 Hz.

Frequency can be defined as, the no.of waves that pass in a unit of time through a fixed point. frequency is measured hertz (Hz)

Wave: The propagation of disturbances that have place in a medium  is referred to as a wave.

There are two types of waves.

1.Longitudinal waves

2.Transverse waves

Wavelength(λ): The distance between two peaks or two troughs can be used to define a wavelength. It is measured in meters (m), centimeters (cm) or millimeters (mm).

Wavelength Formula: λ=ν/f,

where ν is velocity, f is frequency .

To know more about frequency visit :

https://brainly.com/question/29739263

#SPJ4

A frequency of 5 Hz is achieved when 300 waves pass a place in one minute.

To learn more about frequency refer

https://brainly.com/question/27151918

#SPJ4

The amount of charge that will flow from the battery is 77000pC

A capacitor is a device that stores electrical charge. The amount of charge stored in a capacitor is proportional to the voltage applied across it, according to the equation Q = C*V.

where Q is the charge in coulombs, C is the capacitance in farads, and V is the voltage in volts.

In this case, the capacitance of the air-gap capacitor is 3500pF (pico-farads) and the voltage is 22V, so the charge stored in the capacitor is:

Q = 3500pF * 22V = 77000pC (pico-coulombs)

When a piece of mica is placed between the plates, it reduces the space between the plates, which will increase the capacitance of the capacitor. The increase in capacitance will result in an increase in the amount of charge stored in the capacitor.

It's worth noting that the charge that flows from the battery is equal to the initial charge stored in the capacitor. Since the initial charge stored in the capacitor is 77000pC, this is the amount of charge that will flow from the battery.

To learn more about the capacitance of capacitor:

https://brainly.com/question/25884271

#SPJ4

When the stretch distances are at half of their maximum displacement, the acceleration will be half of its maximum value by Hooke's Law.

F= -kx

In accordance with Hooke's law, a principle of elasticity, for relatively minor deformations of an object, the displacement or size of the deformation is directly proportional to the deforming force or load The elasticity of an object is likewise governed by Hooke's law; for example, a metal spring can only be stretched so far before being broken by too much effort. A mass that we already have is then expanded out by x. Displacement and acceleration are inversely related. When the stretch distances are at half of their maximum displacement, the acceleration will be half of its maximum value.

Learn more about Hooke's Law

brainly.com/question/2388910

#SPJ4

The tension in the rope at the 57. 6° angle is 48.58 N, and the tension in the rope at the 33. 8° angle is 36.28 N.

What is meant by angle?

The tension force exerted by the first rope, T1

The tension force exerted by the second rope, T2

and the force of gravity, mg

T1x = −T1 cos 57.6°

T2x = T2 cos 33.8°

mgx = 0

T1y = T1 sin 57.6°

T2y = T2 sin 33.8°

mgy = −mg

Thus, the x and y components of the resultant force will be:

x:

Rx = T1x + T2x + mgx

Rx = −T1 cos 57.6° + T2 cos 33.8° + 0

Rx = T2 cos 33.8° − T1 cos 57.6° (1)

y:

Ry = T1y + T2y + mgy

Ry = T1 sin57.6°+ T2 sin 33.8° + (−mg)

Ry = T1 sin 57.6° + T2 sin33.8° − mg (2)

The next step is to substitute Rx and Ry in Eq. (1) and Eq. (2) with 0:

Rx = T2 cos 33.8° − T1 cos 57.6°

Ry = T1 sin57.6° + T2 sin 33.8° − mg

↓

0 = T2 cos33.8°− T1 cos 57.6° (3)

0 = T1 sin57.6°+ T2 sin 33.8°− mg (4)

Using these two equations we can easily find T1 and T2.

There are multiple ways in which we can do this. One way would be to first solve Eq. (3) for T2:

0 = T2 cos33.8°− T1 cos 57.6°

T2 cos 33.8° − T1 cos 57.6° = 0

T2 cos 33.8° = T1 cos 57.6°

T2 = T1  cos57.6°/ cos 33.8°

T2 = 0.747T1 (5)

hen, we substitute T2 with 0.735T1 in Eq. (4):

0 = T1 sin 57.6°+ T2 sin 33.8° − mg

0 = T1 sin 57.6° + 0.735T1 sin 33.8°− mg

And we solve it for T1:

0 = T1 (sin 57.6° + 0.747 sin 33.8°) − mg

0 = T1 (0.848) − mg

mg = 0.848T1

0.848T1 = mg

T1 =  mg /0.848

T1 =  (4.2kg) (9.81 N/kg) / 0.848T

T1 = 48.58 N

Finally, we substitute the value of T1 in Eq. (5) to find T2:

T2 = 0.747T1

T2 = (0.747) (48.58 N)

T2 = 36.28 N

Therefore, the tension in the rope at the 57. 6°angle is 48.58 N, and the tension in the rope at the 33. 8°angle is 36.28 N.

To learn more about angle refer to

https://brainly.com/question/25716982

#SPJ4

The maximum amount of trans fat as a percentage that could be in this cereal should be 0.5%.

This cereal is formulated to be as healthy as possible, which is why we limit the amount of trans fat to 0.5% or less. Trans fat is an unhealthy form of fat that has been linked to several health conditions, so we strive to keep our trans fat content as low as possible. By limiting trans fats to 0.5% or less, we are confident that this cereal is a healthy choice.

This cereal contains no more than 0.5% trans fat, as mandated by the FDA. Trans fat is an unhealthy type of fat that can increase bad cholesterol levels and the risk of heart disease and stroke. To ensure optimal health and safety, this cereal only contains the amount of trans fat that is legally allowed.

To learn more about trans fat, click here:

https://brainly.com/question/29593073

#SPJ4

The wavelength of light that is inclined at a specified angle when falling on double slits is calculated to be 428.57 nm.

Angle = 30°

Order of interference m = 3

Distance between the slits d = 3 μ m = 3 × 10⁻⁶ m

We know the relation between wavelength, order of interference and distance as,

λ = d sinθ/(m+1/2)

By putting in the values, we have,

⇒ (3 × 10⁻⁶× sin30°)/(3+1/2) = 4.2857 × 10⁻⁷ m

By converting it to nm, we have,

⇒ 4.2857 × 10⁻⁷ × 10⁹ = 428.57 nm

Thus, the required wavelength of light is calculated to be 428.57 nm.

The question is incomplete. The complete question is 'Calculate the wavelength of light that has its third minimum at an angle of 30.0∘ when falling on double slits separated by 3.00 μm. Explicitly, show how you follow the steps in Problem-Solving Strategies for Wave Optics.'

To know more about wavelength:

https://brainly.com/question/16636743

#SPJ4

The amount of the mass of the radioactive isotope remaining after 1 hour is 1.25 g.

The mass of the sample remaining after an hour is calculated from the half life of the isotope as shown below.

The half life of the radioactive isotope = 10 minutes

The amount of the mass of the radioactive isotope remaining after 1 hour is calculated as follows;

1 hour = 60 minutes

0 half life ---------------------------> 10 g

20 minutes ------------------------> 5 g

40 minutes -----------------------> 2.5 g

60 minutes -----------------------> 1.25 g

Learn more about half-life here: https://brainly.com/question/2320811

#SPJ1

In contrast to the human hearing range of 20 Hz to 20 kHz, mouse hearing extends into the ultrasonic region and ranges from 1 to approximately 100 kHz7,9.

To learn more about frequency refer to:

https://brainly.com/question/254161

#SPJ1

The level of the sound can be decreased by gradually draining the air from a plastic bottle. The sound about an alarm clock cannot be heard at all since sound cannot travel through a vacuum.

A ringing alarm clock will gradually grow quieter when air is gently drawn out of the area around it and placed beneath a glass jar. Because sound is indeed a mechanical wave that moves across a medium, this is the case.

We can hear the sound because the air molecules in the jar shake as sound waves pass through them. The amount of air particles available to vibrate and convey sound waves declines when air is eliminated, which lessens the sound's strength.  There will be so little remaining air to vibrate due to the almost full removal of the air that the sound will be almost undetectable.

To know more about vacuum :

https://brainly.com/question/29242274

#SPJ4