Answer:
d. may be either greater, smaller, or equal to that observed inside the bus.
Explanation:
The bus is moving at a constant speed. The ball tossed and received by the ball is inside the bus at a speed equal to the speed of the ball. Therefore the speed of the bus becomes zero with respect to the observer inside the bus. Now the observer inside the bus noticed the ball from the inside of the bus, so he threw the ball back and forth from the ball with the speed v relative to the observer. Now the observer outside the bus could see the bus moving at speed relative to its reference point and also throwing the ball from front to back. The speed of the ball to the observer outside the bus The speed of the bus to the observer outside the bus is minus the speed of the ball to the observer inside the bus. Therefore, the ball speed = (u-v) relative to the observer outside the bus.A 750 kg car is moving at 20.0 m/s at a height of 5.0 m above the bottom of a hill when it runs out of gas. From there, the car coasts. a. Ignoring frictional forces and air resistance, what is the car’s kinetic energy and velocity at the bottom of the hill
Answer:
Explanation:
Kinetic energy at the height = 1/2 m v²
= 1/2 x 750 x 20²
= 150000 J
Its potential energy = mgh
= 750 x 9.8 x 5
=36750 J
Total energy = 186750 J
Its total kinetic energy will be equal to 186750 J , according to conservation of mechanical energy
If v be its velocity at the bottom
1/2 m v² = 186750
v = √498
= 22.31 m /s
A rigid tank A of volume 0.6 m3 contains 5 kg air at 320K and the rigid tank B is 0.4 m3 with air at 600 kPa, 360 K. They are connected to a piston cylinder initially empty with closed valves. The pressure in the cylinder should be 800 kPa to float the piston. Now the valves are slowly opened and the entire process is adiabatic. The internal energy of the mixture at final state is:_____.
a. 229 k/kg.
b. 238 kJ/kg
c. 257 kg
d. cannot be determined.
Answer:
the internal energy of the mixture at final state = 238kJ/kg
Explanation:
Given
V= 0.6m³
m=5kg
R=0.287kJ/kg.K
T=320 K
from ideal gas equation
PV = nRT
where P is pressure, V is volume, n is number of mole, R is ideal gas constant , T is the temperature.
Recall, mole = mass/molar mass
attached is calculation of the question.
A uniform thin rod of mass ????=3.41 kg pivots about an axis through its center and perpendicular to its length. Two small bodies, each of mass m=0.249 kg , are attached to the ends of the rod. What must the length L of the rod be so that the moment of inertia of the three-body system with respect to the described axis is ????=0.929 kg·m2 ?
Answer:
The length of the rod for the condition on the question to be met is [tex]L = 1.5077 \ m[/tex]
Explanation:
The Diagram for this question is gotten from the first uploaded image
From the question we are told that
The mass of the rod is [tex]M = 3.41 \ kg[/tex]
The mass of each small bodies is [tex]m = 0.249 \ kg[/tex]
The moment of inertia of the three-body system with respect to the described axis is [tex]I = 0.929 \ kg \cdot m^2[/tex]
The length of the rod is L
Generally the moment of inertia of this three-body system with respect to the described axis can be mathematically represented as
[tex]I = I_r + 2 I_m[/tex]
Where [tex]I_r[/tex] is the moment of inertia of the rod about the describe axis which is mathematically represented as
[tex]I_r = \frac{ML^2 }{12}[/tex]
And [tex]I_m[/tex] the moment of inertia of the two small bodies which (from the diagram can be assumed as two small spheres) can be mathematically represented as
[tex]I_m = m * [\frac{L} {2} ]^2 = m* \frac{L^2}{4}[/tex]
Thus [tex]2 * I_m = 2 * m \frac{L^2}{4} = m * \frac{L^2}{2}[/tex]
Hence
[tex]I = M * \frac{L^2}{12} + m * \frac{L^2}{2}[/tex]
=> [tex]I = [\frac{M}{12} + \frac{m}{2}] L^2[/tex]
substituting vales we have
[tex]0.929 = [\frac{3.41}{12} + \frac{0.249}{2}] L^2[/tex]
[tex]L = \sqrt{\frac{0.929}{0.40867} }[/tex]
[tex]L = 1.5077 \ m[/tex]
If a sample of 346 swimmers is taken from a population of 460 swimmers,
the population mean, w, is the mean of how many swimmers' times?
Answer:
It is the mean of 460 swimmers
Explanation:
In this question, we are concerned with knowing the mean of the population w
Now, according to the question at hand, we have a total population of 460 swimmers and we have taken out 346 swimmers for a study
The population mean in this case is simply the mean of the swimming times of the 460 swimmers
There is another related thing here called the sample mean. For the sample mean, we only make a reference to the mean of the 346 swimmers who were taken out from the population to conduct a separate study
So conclusively, the population mean w is simply the mean of the total 460 swimmers
Nerve impulses in a human body travel at a speed of about 100 m/s. Suppose a woman accidentally steps barefoot on a thumbtack. About how much time does it take the nerve impulse to travel from the foot to the brain (in s)
a block of wood is pulled by a horizontal string across a rough surface at a constant velocity with a force of 20N. the coefficient of kinetic friction between the surfaces is 0.3 the force of the friction is
Answer:
6 N
Explanation:
From the laws of friction
F = ¶R = 0.3 × 20 = 6 N
The force of friction opposing the block's motion is 6 N.
The given parameters;
force applied on the block, F = 20 Ncoefficient of kinetic friction = 0.3The force of friction which opposes the motion of the block is obtained by applying Newton's second law of motion.
F = ma
Fₓ = μF
Substitute the given parameters to calculate the frictional force on the object.
Fₓ = 0.3 x 20
Fₓ = 6 N
Thus, the force of friction opposing the block's motion is 6 N.
Learn more here: https://brainly.com/question/18247518
An asteroid that has an orbital period of 3 years will have an orbital with a semi-major axis of about _____ years.
Answer:
An asteroid that has an orbital period of 3 years will have an orbital with a semi-major axis of about 2 years.
Explanation:
Given;
orbital period of 3 years, P = 3 years
To calculate the years of an orbital with a semi-major axis, we apply Kepler's third law.
Kepler's third law;
P² = a³
where;
P is the orbital period
a is the orbital semi-major axis
(3)² = a³
9 = a³
a = [tex]a = \sqrt[3]{9} \\\\a = 2.08 \ years[/tex]
Therefore, An asteroid that has an orbital period of 3 years will have an orbital with a semi-major axis of about 2 years.
A 5.0-Ω resistor and a 9.0-Ω resistor are connected in parallel. A 4.0-Ω resistor is then connected in series with this parallel combination. An ideal 6.0-V battery is then connected across the series-parallel combination of the three resistors. What is the current through (a) the 4.0-Ω resistor? (b) the 5.0-Ω resistor? (c) the 9.0-Ω resistor?
Answer:
Explanation:
The current through the resistor is 0.83 A
.
Part b
The current through resistor is 0.53 A
.
Part c
The current through resistor is 0.30 A
How does an atom of rubidium-85 become a rubidium ion with a +1 charge?
Answer:
C. The atom loses 1 electron to have a total of 36.
Explanation:
Cations have a positive charge. Cations lose electrons.
The number of electrons in a Rubidium atom is 37. If the atom loses 1 electron, then it has 36 left.
The lower the value of the coefficient of friction, the____the resistance to sliding
Answer: lower
There are a number of factors that can affect the coefficient of friction, including surface conditions.
Values of the coefficient of sliding friction can be a good reference for specific combinations of materials. The frictional force and normal reaction are directly proportion but an increase or decrease in coefficient of friction will cause an increase or decrease in the resistance of sliding respectively
A solenoid with 500 turns, 0.10 m long, carrying a current of 4.0 A and with a radius of 10-2 m will have what strength magnetic field at its center
Answer:
B = 0.025T
Explanation:
In order to calculate the strength of the magnetic field at the center of the solenoid, you use the following formula:
[tex]B=\frac{\mu N i}{L}[/tex] (1)
μ: magnetic permeability of vacuum = 4π*10^-7 T/A
N: turns of the solenoid = 500
i: current = 4.0A
L: length of the solenoid = 0.10m
You replace the values of the parameters in the equation (1):
[tex]B=\frac{(4\pi*10^{-7}T/A)(500)(4.0A)}{0.10m}=0.025T[/tex]
The strength of the magnetic field at the center of the solenoid = 0.025T
Answer:
Magnetic field strength at the center is 2.51x10^-2T
Explanation:
Pls see attached file for step by step calculation
Julie is playing with a toy car and is pushing it around on the floor. The little car has a mass of 6.3 g. The car has a velocity of 2.5 m/s. What is the car's momentum?
Answer:
Momentum of the car = [tex]1.575\times 10^{-2}[/tex] kg meter per second
Explanation:
Julie is playing with a car which has mass = 6.3 g = [tex]6.3\times 10^{-3}[/tex] kg
Velocity of the car is 2.5 meter per second
Since formula to calculate the momentum of an object is,
p = mv
Where, p = momentum of the object
m = mass of the object
v = velocity of the object
By substituting these values in the formula,
p = [tex](6.3\times 10^{-3})\times 2.5[/tex]
= [tex]1.575\times 10^{-2}[/tex] Kg meter per second
Therefore, momentum of the car will be [tex]1.575\times 10^{-2}[/tex] Kg meter per second.
The voltage between the cathode and the screen of a television set is 30 kV. If we assume a speed of zero for an electron as it leaves the cathode, what is its speed (m/s) just before it hits the screen
Answer:
The speed is [tex]v =10.27 *10^{7} \ m/s[/tex]
Explanation:
From the question we are told that
The voltage is [tex]V = 30 kV = 30*10^{3} V[/tex]
The initial velocity of the electron is [tex]u = 0 \ m/s[/tex]
Generally according to the law of energy conservation
Electric potential Energy = Kinetic energy of the electron
So
[tex]PE = KE[/tex]
Where
[tex]KE = \frac{1}{2} * m* v^2[/tex]
Here m is the mass of the electron with a value of [tex]m = 9.11 *10^{-31} \ kg[/tex]
and
[tex]PE = e * V[/tex]
Here e is the charge on the electron with a value [tex]e = 1.60 *10^{-19} \ C[/tex]
=> [tex]e * V = \frac{1}{2} * m * v^2[/tex]
=> [tex]v = \sqrt{ \frac{2 * e * V}{m} }[/tex]
substituting values
[tex]v = \sqrt{ \frac{2 * (1.60*10^{-19}) * 30*10^{3}}{9.11 *10^{-31}} }[/tex]
[tex]v =10.27 *10^{7} \ m/s[/tex]
An object attached to a horizontal spring is oscillating back and forth along a frictionless surface. The maximum speed of the object is 1.38 m/s, and its maximum acceleration is 6.83 m/s2. How much time elapses betwen an instant when the object's speed is at a maximum and the next instant when its acceleration is at a maximum
Answer:
t = 0.31s
Explanation:
In order to calculate the time that the object takes to travel from the point with its maximum speed to the point with the maximum acceleration, you first use the following formulas, for the maximum speed and the maximum acceleration:
[tex]v_{max}=\omega A\\\\a_{max}=\omega^2A[/tex]
A: amplitude
v_max = 1.38m/s
a_max = 6.83m/s^2
w: angular frequency
From the previous equations you can obtain the angular frequency w.
You divide vmax and amax, and solve for w:
[tex]\frac{v_{max}}{a_{max}}=\frac{\omega A}{\omega^2 A}=\frac{1}{\omega}\\\\\omega=\frac{a_{max}}{v_{max}}=\frac{6.83m/s^2}{1.38m/s^2}=4.94\frac{rad}{s}[/tex]
Next, you take into account that the maximum speed is obtained when the object passes trough the equilibrium point, and the maximum acceleration for the maximum elongation, that is, the amplitude. In such a trajectory the time is T/4 being T the period.
You calculate the period by using the information about the angular frequency:
[tex]T=\frac{2\pi}{\omega}=\frac{2\pi}{4.94rad/s}=1.26s[/tex]
Then the required time is:
[tex]t=\frac{T}{4}=\frac{1.26s}{4}=0.31s[/tex]
Find acceleration. Will give brainliest!
Answer:
16200 km/s
270 km/min
4.5 km/h
Explanation:
Acceleration Formula: Average Acceleration = Δv/Δt (change in velocity over change in time)
Simply plug in our known variables and solve:
a = (45.0 - 0)/10
a = 45.0/10
a = 4.5 km/h
Answer:
[tex]\boxed{\mathrm{4.5 \: kmph/s \: or \: 1.25 \: m/s^2 }}[/tex]
Explanation:
[tex]\displaystyle \mathrm{acceleration = \frac{change \: in \: velocity}{time \: taken}}[/tex]
[tex]\displaystyle \mathrm{a = \frac{v - u}{t}}[/tex]
[tex]\displaystyle \mathrm{v=final \: velocity}\\\displaystyle \mathrm{u=initial \: velocity}[/tex]
[tex]\displaystyle \mathrm{a = \frac{45- 0}{10}}[/tex]
[tex]\displaystyle \mathrm{a = \frac{45}{10}}[/tex]
[tex]\displaystyle \mathrm{a = 4.5}[/tex]
[tex]\mathrm{4.5 \: kmph/s = 1.25 \: m/s^2 }[/tex]
Which of the following statements is accurate? A) Compressions and rarefactions occur throughout a transverse wave. B) The wavelength of both transverse and longitudinal waves is measured parallel to the direction of the travel of the wave. C) Sound waves passing through the air will do so as transverse waves, which vibrate vertically and still retain their horizontal positions. D) Amplitude of longitudinal waves is measured at right angles to the direction of the travel of the wave and represents the maximum distance the molecule has moved from its normal position.
Answer:
B) The wavelength of both transverse and longitudinal waves is measured parallel to the direction of the travel of the wave
Answer:
B) The wavelength of both transverse and longitudinal waves is measured parallel to the direction of the travel of the wave.
Explanation: hope this helps ;)
A commercial diffraction grating has 500 lines per mm. Part A When a student shines a 480 nm laser through this grating, how many bright spots could be seen on a screen behind the grating
Answer:
The number of bright spot is m =4
Explanation:
From the question we are told that
The number of lines is [tex]s = 500 \ lines / mm = 500 \ lines / 10^{-3} m[/tex]
The wavelength of the laser is [tex]\lambda = 480 nm = 480 *10^{-9} \ m[/tex]
Now the the slit is mathematically evaluated as
[tex]d = \frac{1}{s} = \frac{1}{500} * 10^{-3} \ m[/tex]
Generally the diffraction grating is mathematically represented as
[tex]dsin\theta = m \lambda[/tex]
Here m is the order of fringes (bright fringes) and at maximum m [tex]\theta = 90^o[/tex]
So
[tex]\frac{1}{500} * sin (90) = m * (480 *10^{-3})[/tex]
=> [tex]m = 4[/tex]
This implies that the number of bright spot is m =4
When a nerve cell fires, charge is transferred across the cell membrane to change the cell's potential from negative to positive. For a typical nerve cell, 9.2pC of charge flows in a time of 0.52ms .What is the average current through the cell membrane?
Answer:
The average current will be "17.69 nA".
Explanation:
The given values are:
Charge,
q = 9.2 pC
Time,
t = 0.52ms
The equivalent circuit of the cell surface is provided by:
⇒ [tex]i_{avg}=\frac{charge}{t}[/tex]
Or,
⇒ [tex]i_{avg}=\frac{q}{t}[/tex]
On substituting the given values, we get
⇒ [tex]=\frac{9.2\times 10^{-12}}{0.52\times 10^{-3}}[/tex]
⇒ [tex]=17.69^{-9}[/tex]
⇒ [tex]=17.69 \ nA[/tex]
mention two similarities of citizen and aliens
Answer:
The main points of difference between a citizen and alien are: (a) A citizen is a permanent resident of a state, while an alien is a temporary resident, who comes for a specific duration of time as a tourist or on diplomatic assignment. ... Aliens do not possess such rights in the state where they reside temporarily
Explanation:
1. In a Millikan type experiment, two horizontal plates are 2.5 cm apart. A latex sphere of
mass 1.5 x 10-15 kg remains stationary when the potential difference between the
plates is 460 V, with the upper plate positive. [2+2+2+2 = 8 marks]
a. Is the sphere charged negatively or positively?
b. What is the magnitude of the electric field intensity between the plates?
C. Calculate the magnitude of the charge on the latex sphere.
d. How many excess or deficit electrons does the sphere have?
Answer:
Explanation:
a. Is the sphere charged negatively or positively?
The sphere us negatively charged. In a Millikan type experiment, there will be two forces that will be acting on the sphere which are the electric force which acts upward and also the gravity which acts downward.
Because the upper plate is positively charged, there'll what an attractive curve with an upward direction which will be felt by the negatively charged sphere.
b. What is the magnitude of the electric field intensity between the plates?
The magnitude of the electric field intensity between the plates is 18400v/m.
C. Calculate the magnitude of the charge on the latex sphere.
The magnitude of the charge on the latex sphere hae been solved and attached
d. How many excess or deficit electrons does the sphere have?
There are 5 excess electrons that the sphere has.
Check the attachment for further explanation.
If 62.9 cm of copper wire (diameter = 1.15 mm, resistivity = 1.69 × 10-8Ω·m) is formed into a circular loop and placed perpendicular to a uniform magnetic field that is increasing at the constant rate of 8.43 mT/s, at what rate is thermal energy generated in the loop?
Answer:
The answer is "[tex]\bold{7.30 \times 10^{-6}}[/tex]"
Explanation:
length of the copper wire:
L= 62.9 cm
r is the radius of the loop then:
[tex]r=\frac{L}{2 \pi}\\[/tex]
[tex]=\frac{62.9}{2\times 3.14}\\\\=\frac{62.9}{6.28}\\\\=10.01\\[/tex]
area of the loop Is:
[tex]A_L= \pi r^2[/tex]
[tex]=100.2001\times 3.14\\\\=314.628[/tex]
change in magnetic field is:
[tex]=\frac{dB}{dt} \\\\ = 0.01\ \frac{T}{s}[/tex]
then the induced emf is: [tex]e = A_L \times \frac{dB}{dt}[/tex]
[tex]=314.628 \times 0.01\\\\=3.14\times 10^{-5}V[/tex]
resistivity of the copper wire is: [tex]\rho =[/tex] 1.69 × 10-8Ω·m
diameter d = 1.15mm
radius (r) = 0.5mm
[tex]= 0.5 \times 10^{-3} \ m[/tex]
hence the resistance of the wire is:
[tex]R=\frac{\rho L}{\pi r^2}\\[/tex]
[tex]=\frac{1.69 \times 10^{-8}(62.9)}{3.14 \times (0.5 \times 10^{-3})^2}\\\\=\frac{1.69 \times 10^{-8}(62.9)}{3.14 \times 0.5 \times 0.5 \times 10^{-6}}\\\\=\frac{1.69 \times 10^{-8}(62.9)}{3.14 \times 0.25 \times 10^{-6}}\\\\=135.41 \times 10^{-2}\\=1.35\times 10^{-4}\\[/tex]
Power:
[tex]P=\frac{e^2}{R}[/tex]
[tex]=\frac{3.14\times 10^{-5}\times 3.14\times 10^{-5}}{1.35 \times 10^{-4}}\\\\=7.30 \times 10^{-6}[/tex]
The final answer is: [tex]\boxed{7.30 \times 10^{-6} \ W}[/tex]
3. Two spherical objects at the same altitude move with identical velocities and experience the same drag force at a time t. If Object 1 has twice (2x) the diameter of Object 2, which object has the larger drag coefficient? Explain your answer using the drag equation.
Answer:
Object 2 has the larger drag coefficient
Explanation:
The drag force, D, is given by the equation:
[tex]D = 0.5 c \rho A v^2[/tex]
Object 1 has twice the diameter of object 2.
If [tex]d_2 = d[/tex]
[tex]d_1 = 2d[/tex]
Area of object 2, [tex]A_2 = \frac{\pi d^2 }{4}[/tex]
Area of object 1:
[tex]A_1 = \frac{\pi (2d)^2 }{4}\\A_1 = \pi d^2[/tex]
Since all other parameters are still the same except the drag coefficient:
For object 1:
[tex]D = 0.5 c_1 \rho A_1 v^2\\D = 0.5 c_1 \rho (\pi d^2) v^2[/tex]
For object 2:
[tex]D = 0.5 c_2 \rho A_2 v^2\\D = 0.5 c_2 \rho (\pi d^2/4) v^2[/tex]
Since the drag force for the two objects are the same:
[tex]0.5 c_1 \rho (\pi d^2) v^2 = 0.5 c_2 \rho (\pi d^2/4) v^2\\4c_1 = c_2[/tex]
Obviously from the equation above, c₂ is larger than c₁, this means that object 2 has the larger drag coefficient
A dumbbell-shaped object is composed by two equal masses, m, connected by a rod of negligible mass and length r. If I1 is the moment of inertia of this object with respect to an axis passing through the center of the rod and perpendicular to it and I2 is the moment of inertia with respect to an axis passing through one of the masses, it follows that:
a. I1 > I2
b. I2 > I1.
c. I1 = I2.
Answer:
B: I2>I1
Explanation:
See attached file
Copper wire of diameter 0.289 cm is used to connect a set of appliances at 120 V, which draw 1850 W of power total. The resistivity of copper is 1.68×10−8Ω⋅m.
A. What power is wasted in 26.0 m of this wire?
B. What is your answer if wire of diameter 0.417 cm is used?
Answer:
(a) The power wasted for 0.289 cm wire diameter is 15.93 W
(b) The power wasted for 0.417 cm wire diameter is 7.61 W
Explanation:
Given;
diameter of the wire, d = 0.289 cm = 0.00289 m
voltage of the wire, V = 120 V
Power drawn, P = 1850 W
The resistivity of the wire, ρ = 1.68 x 10⁻⁸ Ω⋅m
Area of the wire;
A = πd²/4
A = (π x 0.00289²) / 4
A = 6.561 x 10⁻⁶ m²
(a) At 26 m of this wire, the resistance of the is
R = ρL / A
R = (1.68 x 10⁻⁸ x 26) / 6.561 x 10⁻⁶
R = 0.067 Ω
Current in the wire is calculated as;
P = IV
I = P / V
I = 1850 / 120
I = 15.417 A
Power wasted = I²R
Power wasted = (15.417²)(0.067)
Power wasted = 15.93 W
(b) when a diameter of 0.417 cm is used instead;
d = 0.417 cm = 0.00417 m
A = πd²/4
A = (π x 0.00417²) / 4
A = 1.366 x 10⁻⁵ m²
Resistance of the wire at 26 m length of wire and 1.366 x 10⁻⁵ m² area;
R = ρL / A
R = (1.68 x 10⁻⁸ x 26) / 1.366 x 10⁻⁵
R = 0.032 Ω
Power wasted = I²R
Power wasted = (15.417²)(0.032)
Power wasted = 7.61 W
Five identical cylinders are each acted on by forces of equal magnitude. Which force exerts the biggest torque about the central axes of the cylinders
Answer:
From the image, the force as shown in option A will exert the biggest torque on the cylinder about its central axes.
Explanation:
The image is shown below.
Torque is the product of a force about the center of rotation of a body, and the radius through which the force acts. For a given case such as this, in which the cylinders are identical, and the forces are of equal magnitude, the torque at the maximum radius away from the center will exert the maximum torque. Also, the direction of the force also matters. To generate the maximum torque, the force must be directed tangentially away from the circle formed by the radius through which the force acts away from the center. Option A satisfies both condition and hence will exert the most torque on the cylinder.
What is the length (in m) of a tube that has a fundamental frequency of 108 Hz and a first overtone of 216 Hz if the speed of sound is 340 m/s?
Answer:
Length of a tube = 1.574 m
Explanation:
Given:
Fundamental frequency (f1) = 108 Hz
First overtone (f2) = 216 Hz
Speed of sound (v) = 340 m/s
Find:
Length of a tube
Computation:
We know that,
f = v / λ
f = nv / 2L [n = number 1,2,3]
So,
f1 = 1(340) / 2L
f1 = 170 / L
L = 170 / 108 = 1.574 m
f2 = 2(340) / 2L
L = 340 / 216
L = 1.574 m
Which of the following changes will increase the frequency of the lowest frequency standing sound wave on a stretching string?Choose all that apply.A. Replacing the string with a thicker stringB. Plucking the string harderC. Doubling the length of the string
Answer:
A, C
Explanation:
Since the frequency is inversely proportional to the length of a string, then I want to increase the frequency of the lowest
A. Replacing the string with a thicker string.
Thicker strings have more density. The more density the string has, the lower the sound.
Mathematically, we can see the proportionality (direct and inverse) by looking at those formulas for Frequency and Speed, when combined:
For:
[tex]f=\frac{v}{\lambda}[/tex]
[tex]f=\frac{v}{\lambda}*\sqrt{\frac{T}{D} }[/tex]
See above, how density (D) and [tex](\lambda)[/tex] wave length are inversely proportional.
C. Doubling the length of the string.
Because the length of the string is inversely proportional to the frequency.
The longer the string, the lower the frequency.
So, if we double string, we'll hear lower sounds in any string instrument
--
In short, for A, and C We can justify both since length and density are inversely proportional to the Frequency, we need longer or thicker string.
A 1,470-N force pushes a 500-kg piano up along a ramp. What is the work done by the 1,470-N pushing force on the piano as it moves 10 m up the ramp
Answer:
W = 14700 J
Explanation:
This is an exercise on Newton's second law.
To solve it we must fix a coordinate system, the most common is an axis parallel to the ramp and the other perpendicular axis, we write Newton's second law
Y Axis . Perpendicular to the ramp
N - Wy = 0
X axis. Parallel to the ramp, we assume it is positive when the ramp is going up
F - Wx = m a
in this case F = 1470 N and it is parallel to the plane.
Work is defined by
W = F .d
boldface indicates vectors
W = F d cos θ
let's calculate
W = 1470 10 cos 0
W = 14700 J
An empty parallel plate capacitor is connected between the terminals of a 9.0-V battery and charged up. The capacitor is then disconnected from the battery, and the spacing between the capacitor plates is doubled. As a result of this change, what is the new voltage between the plates of the capacitor
Answer:
The new voltage between the plates of the capacitor is 18 V
Explanation:
The charge on parallel plate capacitor is calculated as;
q = CV
Where;
V is the battery voltage
C is the capacitance of the capacitor, calculated as;
[tex]C = \frac{\epsilon _0A}{d} \\\\q =CV = (\frac{\epsilon _0A}{d})V = \frac{\epsilon _0A V}{d}[/tex]
[tex]q = \frac{\epsilon _0A V}{d}[/tex]
where;
ε₀ is permittivity of free space
A is the area of the capacitor
d is the space between the parallel plate capacitors
If only the space between the capacitors is doubled and every other parameter is kept constant, the new voltage will be calculated as;
[tex]q = \frac{\epsilon _0A V}{d} \\\\\frac{\epsilon _0A V}{d} = \frac{\epsilon _0A V}{d} \\\\\frac{V_1}{d_1} = \frac{V_2}{d_2} \\\\V_2 = \frac{V_1d_2}{d_1} \\\\(d_2 = 2d_1)\\\\V_2 = \frac{V_1*2d_1}{d_1} \\\\(V_1 = 9V)\\\\V_2 = \frac{9*2d_1}{d_1} \\\\V_2 = 9*2\\\\V_2 = 18 \ V[/tex]
Therefore, the new voltage between the plates of the capacitor is 18 V
A 100 kg lead block is submerged in 2 meters of salt water, the density of which is 1096 kg / m3. Estimate the value of the hydrostatic pressure.
Answer:
21,920 Pascals
Explanation:
P = ρgh
P = (1096 kg/m³) (10 m/s²) (2 m)
P = 21,920 Pa