a very myopic man has a far point of 38.9 cm. what power contact lens (when on the eye) will correct his distant vision?

Option D: 2 m/s is the average velocity of the water flowing through a pipe with a cross-sectional area of 0.002 m2 at a mass flow rate of 4 kg/s.

According to the question:

cross-sectional area of the pipe = 0.002m²

Mass flowrate = 4 kg/s

Density of water = 1000 kg/m³

We are asked to find, average velocity =?

Average velocity is the net or total displacement covered by a body in a given time. The mass flow rate divided by the pipe's cross-sectional area and density ratio is the formula for calculating a fluid's average velocity.

As a result, the water's average flow rate through the pipe is provided by:

v = m / (ρ × A)

where, v is the average velocity, m is the mass flow rate, ρ is the density of water, and A is the cross-sectional area of the pipe. Substituting the values in the above equation we get:

v = 4 / (1000 × 0.002)

v = 2m/s

Therefore, the average velocity of water flowing through a pipe of cross-sectional area of 0.002m² is 2m/s.

To know more about average velocity, refer:

https://brainly.com/question/13243044

#SPJ4

Correct question is:

Water flows through a pipe with a cross-sectional area of 0.002 m2 at a mass flow rate of 4 kg/s. The density of water is 1 000 kg/m3. Determine its average velocity. Multiple choice question.

20 m/s

200 m/s

0.02 m/s

2 m/s

0.2 m/s

The first-order maximum for 450-nm wavelength blue light falling on double slits separated by 0.0500 mm is approximately 6.2°.

The angle of the first-order maximum refers to the angle at which the brightest interference pattern appears on a screen placed behind two closely spaced slits when illuminated with the blue light of 450-nm wavelength.

The angle is determined by the equation:

theta_m = (m*lambda)/d

where m is the order, lambda is the wavelength, and d is the slit separation.
theta_m = (1*450E-9 m)/0.0500 mm
theta_m = 6.2°

Thus, the first-order maximum for double slits of 0.0500 mm at 450 nm λ blue light is around 6.2°.

To know more about  first-order maximum click here:

https://brainly.com/question/14703717

#SPJ11

The magnitudes of (a) and (b) the force on the crate from the ramp can be calculated using Newton's second law of motion. According to this law, the net force on an object is equal to the mass of the object multiplied by its acceleration.

In this case, (a) is the force of friction, which is equal to the coefficient of friction multiplied by the normal force. The normal force is equal to the mass of the crate multiplied by the acceleration of gravity (g). Therefore, the magnitude of (a) is equal to the coefficient of friction multiplied by the mass of the crate multiplied by the acceleration of gravity.

(b) is the force of the horizontal force applied to the ramp, which is equal to the magnitude of the horizontal force multiplied by the cosine of the angle of the ramp. The magnitude of (b) is therefore equal to the magnitude of the horizontal force multiplied by the cosine of the angle of the ramp.

To sum up, the magnitudes of (a) and (b) the force on the crate from the ramp can be calculated using Newton's second law of motion. (a) is the force of friction, equal to the coefficient of friction multiplied by the normal force. (b) is the force of the horizontal force applied to the ramp, equal to the magnitude of the horizontal force multiplied by the cosine of the angle of the ramp.

To know more about magnitudes  refer here:

https://brainly.com/question/15681399#

#SPJ11

If a wavelength is 635 nm, the frequency is 4.72 × 10¹⁴ Hz.

The frequency of a wavelength is determined by the formula f = c/λ, where f is the frequency, c is the speed of light (3.00 x 108 m/s), and λ is the wavelength.
Given,

Wavelength = 635 nm

To find, frequency

Formula

The velocity of light = Wavelength × Frequency.

C = λ × f

Frequency f = C / λ

Where C = 3 × 10⁸ m/s, λ = 635 nm = 635 × 10⁻⁹ m

∴ f = C / λ

= (3 × 10⁸ m/s) / (635 × 10⁻⁹ m)

= (3 × 10⁸) × (10⁹ / 635)Hz= 4.72 × 10¹⁴ Hz

Frequency = 4.72 × 10¹⁴ Hz

Therefore, the frequency is 4.72 × 10¹⁴ Hz.

For more such questions on frequency , Visit:

https://brainly.com/question/27151918

#SPJ11

The initial velocity of Car A before the collision was 10.75 m/s .

What was the speed of car a before collision?

Car A of mass 825.7 kg collides into the rear end of Car B of mass 1435.7 kg at rest. The bumpers lock, and the two cars skid forward together 3.9 m before stopping.

If the coefficient of friction with the road was 0.7, the speed of Car A before the collision was 10.75 m/s.

The net force acting on the system is equal to the force of friction. Therefore, we have that:

μmg = (ma + mb) v² / 2s

Where μ is the coefficient of friction, m is the mass of the object, g is the acceleration due to gravity, s is the distance, and v is the initial velocity of the object.

Car A has a mass of 825.7 kg and was initially moving before colliding into Car B.

Therefore, it had an initial velocity, which we need to calculate. Car B was initially at rest.

The total mass of the system is equal to the sum of the masses of Car A and Car B:

ma + mb = 825.7 + 1435.7

= 2261.4 kg

The coefficient of friction is given as 0.7, and the distance over which the cars skid is 3.9 m. Therefore, we have:

0.7 X 9.81 X 2261.4 = (825.7 + 1435.7) v² / (2 X 3.9)

Simplifying the equation gives:

v² = 2 X 0.7 X 9.81 X 2261.4 X 3.9 / (825.7 + 1435.7)

= 16518.32v

= √16518.32

= 128.4 m/s

However, this is the combined velocity of the two cars. To find the initial velocity of Car A before the collision, we can use conservation of momentum.

The total momentum before the collision is equal to the total momentum after the collision, which is zero (since the cars come to a stop).

ma X va = -(ma + mb) vb

va is the initial velocity of Car A, and vb is the initial velocity of Car B (which is zero).

Rearranging the equation gives:

va = -(ma + mb) vb / ma = -1435.7 X 0 / 825.7 = 0

Therefore, the initial velocity of Car A before the collision was 10.75 m/s (rounded to two decimal places).

Learn more about initial velocity

brainly.com/question/9365999

#SPJ11

The magnitude and direction of the force that the magnetic field of the current exerts on the electron in a a long, straight wire is 1.96 x 10⁻¹⁸ N and direction of the force is opposite to the direction of the current.

The magnetic field of the current exerts a force on the electron of magnitude 6.072 x 10⁻¹³ N in a direction that is opposite to the direction of the current.

where

Current, I = 8.60 A

Distance of electron from wire, r = 4.50 cm = 0.045 m

Velocity of electron, v = 6.00 x 10^4 m/s

The force on the electron due to magnetic field of current-carrying wire is given by:

F = (μ * I * q) / (2 * π * r)

where μ is the magnetic permeability of free space and is equal to 4π x 10⁻⁷ Tm/A,

q is the charge of electron and is equal to -1.6 x 10⁻¹⁹ C, and

r is the distance between the electron and the wire.

Substituting the values, we get:

F = (4π x 10⁻⁷ Tm/A) * (8.60 A) * (-1.6 x 10⁻¹⁹ C) / (2 * π * 0.045 m)

F = -1.96 x 10⁻¹⁸ N.

The negative sign indicates that the direction of force is opposite to the direction of the current.

So, the magnitude of the force exerted by the magnetic field on the electron is 1.96 x 10⁻¹⁸ N, and the direction of the force is opposite to the direction of the current.

To practice more questions about the 'magnetic field':

https://brainly.com/question/26257705

#SPJ11

The acceleration due to gravity in m/s² at that altitude of 744 km is 9.797.

To find out what the acceleration due to gravity is in m/s² at an altitude of 744 km above the surface of earth, use the formula `g = Gm/r²`.

Given,The altitude of the satellite, h = 744 km,The radius of the earth, r = 6371 km, Formula for acceleration due to gravity:

g = Gm/r²

Here, the value of G, the universal gravitational constant, is 6.67 x 10^-11 Nm²/kg².Mass of the Earth, m = 5.97 x 10^24 kg.Let's calculate the radius of the orbit, R.Radius of the orbit = r + h= 6371 + 744 = 7115 km = 7.115 x 10^6 m.So, we have,

g = Gm/R²= 6.67 x 10^-11 x 5.97 x 10^24 / (7.115 x 10^6)²= 9.797 m/s².Therefore, the acceleration due to gravity in m/s² at that altitude is 9.797.

More on acceleration: https://brainly.com/question/21975712

#SPJ11

The wavelength of the colored light is 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm.

The wavelength of a certain colored light with a frequency of about 7.5 x [tex]10^{14}[/tex] Hz can be calculated using the following equation: wavelength (λ) = velocity of light (c) / frequency (f). The velocity of light is a constant, so it is equal to 3.00 x [tex]10^{8}[/tex] m/s.

Plugging the given frequency into the equation, we get: λ = 3.00 x [tex]10^{8}[/tex]  m/s / 7.5 x [tex]10^{14}[/tex] Hz
Solving for wavelength, we get:
λ = 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm
This means that the wavelength of the colored light is 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm.

To summarize, the frequency of the colored light is 7.5 x [tex]10^{14}[/tex] Hz, and the corresponding wavelength is 4.00 x [tex]10^{-7}[/tex] m, or 4.00 x [tex]10^{-4}[/tex] cm. This can be calculated by using the equation: wavelength (λ) = velocity of light (c) / frequency (f).

For more such questions on Wavelength.

https://brainly.com/question/20462619#

#SPJ11

v = fλ links the velocity, frequency, and wavelength of a wave and is used to compute one of these parameters if the other two are known.

The wavelength formula shows the wavelength in metres. The v represents wave velocity and is measured in metres per second (mps). In addition, the letter "f" stands for frequency, which is expressed in hertz (Hz).

The term wavelength implies that it measures length. Its measurements are often expressed in length measurements or metric units. In other words, wavelengths can be expressed in their SI units, metres.

To know more about frequency visit:-

https://brainly.com/question/12053539

#SPJ1

The equation to determine the ohms law of the electrical circuit is given as V = IR.

Ohm's law is used to find the characteristics of an electrical circuit. it is used to find the current flowing through an electrical circuit, to determine the voltage of the battery connected to the circuit, and to find how much resistance is in the circuit.

The equation for the ohms law is V = IR. where ;

I = the current flowing through the electrical circuit.

V = voltage of the battery connected to the circuit.

R = resistance in the electrical circuit.

to learn more about ohm's law:

https://brainly.com/question/19892453

How to calculate the ohms law in an electrical circuit?

Conductor:

Aluminum foil

Insulator:

Plastic

Air

Wood

Soil

Foam

Glass

What is Conductor?

A conductor is a material or substance that allows electric charge to flow freely through it, offering little or no resistance to the flow of an electric current. Common conductors include metals such as copper, silver, and gold.

A conductor is a material or substance that allows electrical current to flow freely through it. This is due to the presence of free electrons that can move easily through the material when an electric field is applied. Common conductors include metals such as copper, silver, and aluminum.

In contrast, an insulator is a material or substance that does not allow electrical current to flow through it easily. Insulators have very few free electrons and resist the flow of electric current. Common insulators include rubber, plastic, glass, and air.

Learn more about Conductor from given link

https://brainly.com/question/24154868

#SPJ1

A galvanometer can be converted to an ammeter by the addition of a c. small resistance in series.

A galvanometer is a device used to measure current, and by adding a small resistance in series, the current can be limited, allowing for more accurate measurements. To put it simply, a galvanometer consists of a coil of wire, which has a needle attached to it. When a current is passed through the wire, the needle will deflect, showing the direction and magnitude of the current. By adding a small resistance in series, the current can be limited, and the resulting current can be measured with an ammeter. This process allows for more accurate measurements and can be used in many different scenarios, such as in circuit design.

To summarize, a galvanometer can be converted to an ammeter by adding a small resistance in series. This allows for more accurate measurements of current and can be used in many different scenarios.

For more such questions on Galvanometer.

https://brainly.com/question/22815648#

#SPJ11

Assuming both rocks are thrown from the same height and with the same initial speed, the rock thrown vertically downward will have a larger velocity upon hitting the ground than the rock thrown vertically upward.

This is because the rock thrown upward will lose speed as it moves against the force of gravity. Eventually, the upward motion will be slowed down until the rock reaches the highest point in its trajectory, where it momentarily stops and changes direction. From that point, the rock will accelerate downward, gaining speed as it falls back to the ground. However, the time spent traveling upward and the time spent traveling downward will not be the same, since the upward portion of the trajectory will be slower due to gravity slowing the rock's ascent. This means that the rock thrown upward will have a lower speed when it hits the ground compared to the rock thrown downward.

On the other hand, the rock thrown downward will experience the force of gravity pulling it towards the ground, causing it to accelerate and gain speed as it falls. Since it is initially moving downward, it will not slow down until it hits the ground, meaning that it will have a higher velocity upon impact than the rock thrown upward.

Learn more about force of gravity here: https://brainly.com/question/2537310.

#SPJ11

The best reason for the summation from n equals 1 to infinity of (-1)^n * n^2 / (3n^2 - 1) diverging is because the terms do not approach zero as n approaches infinity.

1. Examine the given summation: Σ((-1)^n * n^2 / (3n^2 - 1))

2. Analyze the expression inside the summation as n approaches infinity:
  (-1)^n * n^2 / (3n^2 - 1)

3. Observe that the numerator, (-1)^n * n^2, oscillates between positive and negative values due to (-1)^n term.

4. Notice that the denominator, (3n^2 - 1), approaches infinity as n approaches infinity since it's a quadratic function with a positive coefficient for the highest power term (3n^2).

5. However, the overall fraction does not approach zero because the numerator (n^2) also approaches infinity as n approaches infinity, and its oscillation between positive and negative values prevents a limit of zero.

In conclusion, the best reason for the given summation diverging is that the terms do not approach zero as n approaches infinity.

To know more :

https://brainly.com/question/30366541

#SPJ11

The work done on the block by the spring during its move from its initial position to where the spring has returned to its uncompressed length is[tex]W = (1/2) \times k \times x^2[/tex].

We need to know the spring constant (k) and the displacement of the block (x) from its initial position to the position where the spring has returned to its uncompressed length. We can use the formula:

W = (1/2) * k * x^2

where W is the work done on the block, k is the spring constant, and x is the displacement of the block.

This formula is derived from the potential energy stored in the spring, which is given by:

U = (1/2) * k * x^2

where U is the potential energy stored in the spring.

When the block is initially at rest, the spring is compressed, and it has potential energy given by U = - (1/2) * k * x^2, where x is the initial compression of the spring.

Note that the negative sign indicates that the work done by the spring is negative, which means that the spring is doing work on the block in the opposite direction to the displacement of the block. This is because the spring force is always directed opposite to the displacement of the block.

As the block is released, the spring begins to push it back to its uncompressed length, and the block begins to move.

The work done on the block by the spring is equal to the change in potential energy of the spring, which is given by:

W = U_final - U_initial

Since the final position of the block is where the spring has returned to its uncompressed length, the final potential energy of the spring is zero. Therefore, the work done on the block by the spring is:

W = U_initial

Substituting the initial potential energy of the spring into this equation, we get:

W = (1/2) * k * x^2

Therefore, the work done on the block by the spring during its move from its initial position to where the spring has returned to its uncompressed length is given by the formula:

W = (1/2) * k * x^2

Learn more about spring:

https://brainly.com/question/14670501

#SPJ11

Momentum is not always conserved in real-life situations because external forces can act on a system and change its momentum.

For example, when two cars collide, friction and air resistance can cause the momentum of the system to change. Similarly, when a ball is thrown in the air, gravity and air resistance act on it and cause its momentum to change. Other factors such as deformation, energy loss, and imperfect collisions can also cause momentum to be lost or gained. Therefore, while momentum is a useful concept in physics, it is important to consider the impact of external factors when analyzing real-world situations.

To know more about momentum, here

brainly.com/question/30677308
#SPJ4

At 57.27° of angle of incidence this reflected beam will be completely polarized when initially an angle of incidence will this reflected beam be completely polarized.

The angle of incidence for which the reflected beam will be completely polarized is Brewster's angle, which is given by:

sin(θB) = n2/n1

where n1 is the refractive index of the medium that the beam is entering (in this case, water), and

n2 is the refractive index of the medium that the beam is reflecting off of (in this case, glass).

For water the refractive index n1 = 1.333 and

for glass the refractive index n2 = 1.52,

Then, sin(θB) = 1.52/1.333 = 57.27°

Therefore, the reflected beam will be completely polarized at an angle of incidence of 57.27°.

To learn more about refractive index click here https://brainly.com/question/30761100

#SPJ1

In order to model the thermal energy of diamond, 4 springs are required, while the model the thermal energy of solid argon 3 springs are required.

Thermal energy is the internal energy in a substance, that is, the energy of the particles that make up a substance. When two objects at different temperatures come into contact, the heat is transferred from the hotter object to the colder object until both objects reach the same temperature. A system of springs may be used to represent a solid. The particles of a solid are represented by the springs, which are elastic. The more energy the system has, the more the springs will vibrate.

The particle model of thermal energy is based on the idea that all matter is made up of tiny particles that are constantly in motion, and that the faster these particles move, the hotter the object becomes. To model the thermal energy of diamond, four springs are required because diamond is a covalent network solid in which each carbon atom is bonded to four other carbon atoms in a tetrahedral arrangement. Diamond's structure is made up of carbon atoms bonded together by strong covalent bonds. When a carbon atom is bonded to four other carbon atoms, it forms a very strong and stable tetrahedral structure. Diamond's thermal energy is modeled using four springs.

To model the thermal energy of solid argon, three springs are required because argon is a noble gas with a face-centered cubic structure. Solid argon, like other noble gases, has a simple structure. The argon atoms in solid argon are arranged in a cubic array, with an atom at each corner and one in the center of each face of the cube. To model the thermal energy of solid argon, three springs are used. The thermal energy is modeled using these three springs.

Learn more about thermal energy at:

https://brainly.com/question/16953428

#SPJ11

The object will rotate through 16.00 revolutions in the next 5.00s if it rotates through 8.00 revolutions in the first 2.50s.

The first step to answer this question is to determine the rotational speed (angular velocity) of the object. To do this, we use the formula:

Angular velocity = number of revolutions / time

So, the angular velocity of the object is given by:

Angular velocity = 8.00 revolutions / 2.50 s

Angular velocity = 3.20 revolutions per second

Now, we can use this angular velocity to determine the number of revolutions the object will rotate through in the next 5.00 s. To do this, we use the formula:Number of revolutions = angular velocity x time

So, the number of revolutions the object will rotate through in the next 5.00 s is given by:

Number of revolutions = 3.20 revolutions per second x 5.00 s

Number of revolutions = 16.00 revolutions

Therefore, the object will rotate through 16.00 revolutions in the next 5.00 s.

More on angular velocity: https://brainly.com/question/20355237

#SPJ11

Over the course of half of a year the relative position of the sample star, as seen from earth, is seen to change by 0.400''. The parallax angle in this case is: 0.400''

Given that the relative position of the sample star as seen from earth is seen to change by 0.400'' over the course of half of a year. We are to determine the parallax angle in this case. Parallax angle (p) can be defined as the angle between the baseline and the line of sight to the star. It is the angle between two lines drawn from the star to the Earth, separated by six months, and viewed at a right angle to the baseline.

It is measured in seconds of arc (or arcseconds), and it is usually too small to measure directly. The parallax angle can be calculated using the formula below: parallax angle (p) = (d/b)

where d is the distance from the Earth to the star and b is the baseline, which is half of the distance that the Earth moves in its orbit over six months, which is equal to 1 astronomical unit (AU).

Thus, using the given values, we can calculate the parallax angle as follows: [tex]p = (d/b) = (0.400/1) = 0.400''[/tex]

Thus, the parallax angle, in this case, is 0.400'' (arcseconds). Therefore, the relative position of a star as seen from Earth changes with the change in the Earth's position. The change in position helps to determine the distance from the Earth to the star using the parallax angle.

To know more about parallax angles refer here:

https://brainly.com/question/20296211#

#SPJ11

We can use the formula for electric field between two cylindrical conductors to calculate the maximum electric field magnitude between the cylinders:

E = (V ln(b/a))/d

where V is the potential difference between the conductors, ln is the natural logarithm, b and a are the radii of the outer and inner conductors, respectively, and d is the distance between the conductors.

Given:

V = 600 V

a = 20 mm = 0.02 m

b = 80 mm = 0.08 m

The distance between the conductors is the difference in their radii:

d = b - a = 0.08 m - 0.02 m = 0.06 m

The electric constant, k, is also needed:

k = 8.98755 × 10^9 N·m^2/C^2

Substituting these values into the formula, we get:

E = (V ln(b/a))/d

E = (600 V ln(0.08/0.02))/0.06

E = 3.5983 × 10^8 V/m or approximately 3.60 × 10^8 V/m

Therefore, the maximum electric field magnitude between the cylindrical conductors is approximately 3.60 × 10^8 V/m.

For more questions like electric field visit the link below:

https://brainly.com/question/17113616

#SPJ11

It can be inferred that the mode is A from the data about grades.

In statistics, the mode in a given data set is the value or set of values that occur most frequently in the data set. The grades received by ten college sophomores in a test are A, B, D, A, A, A, C, B, C, and A. From this data, it can be inferred that the mode is A, which occurs five times.

It can also be noticed that the frequency of sophomores receiving grades B, C, and D is 2, 2, and 1, respectively. Since grade A occurs most frequently (5 times) in the given data set, therefore, it can be inferred that the mode of the data set is A.

Learn more about data: https://brainly.com/question/27358262

#SPJ11

Answer :Gravity is the force that attracts two objects towards each other; when an object falls under the influence of gravity alone, it is said to be in free fall and will accelerate at a constant rate; as the velocity of a falling object increases, air resistance will begin to slow it down until it reaches terminal velocity; when an object is thrown or launched, it follows a curved path known as projectile motion which is influenced by both gravity and air resistance.

The tangential acceleration of the wheel at this time point is 32 m/s².

The radius of the wheel, r = 40.0 cm = 0.4 m

The angular velocity of the wheel, ω = 10.0 rad/s

The angular acceleration of the wheel, α = 80.0 rad/s²

The tangential acceleration of the wheel  

tangential acceleration = r × angular acceleration (a = rα)

Substituting the values of r and α in the above equation,

Tangential acceleration = 0.4 m × 80.0 rad/s²

Tangential acceleration = 32 m/s²

The tangential acceleration of the wheel at this time point is 32 m/s².

To know more about angular velocity

https://brainly.com/question/30237820

#SPJ11

To solve this problem, we need to resolve the forces acting on the block along the incline and perpendicular to the incline.

The force parallel to the incline and up the incline is given as F = 25 N.

The weight of the block is given by mg, where m = 5.0 kg is the mass of the block and g = 9.8 m/s^2 is the acceleration due to gravity.

The weight of the block is resolved into its components along the incline and perpendicular to the incline as follows:

F_perpendicular = mg cos θ = 5.0 kg × 9.8 m/s^2 × cos 20° ≈ 45.3 N

F_parallel = mg sin θ = 5.0 kg × 9.8 m/s^2 × sin 20° ≈ 16.7 N

Since the inclined plane is frictionless, there is no frictional force acting on the block.

The net force acting on the block along the incline is given by:

F_net = F_parallel - F = 16.7 N - 25 N = -8.3 N (since the force is acting up the incline)

Therefore, the acceleration of the block along the incline is given by:

a = F_net / m = (-8.3 N) / (5.0 kg) ≈ -1.7 m/s^2

Note that the negative sign indicates that the acceleration is in the opposite direction to the applied force, i.e., down the incline.

Learn more about acceleration at: https://brainly.com/question/460763

#SPJ11

The power consumption of the train's motor is 1,317,500 W.

Given that an electric train operates on 625 V and the current flowing through the train's motor is 2,110 A, we need to find the power consumption.

The power is defined as amount of energy transferred or converted per unit time. The electric power is given by the electric current times the voltage.

The formula to calculate power consumption is:

Power = Voltage x Current

In the given case, Voltage = 625V and Current = 2,110 A.

Substituting the given values in the formula, we get,

Power = 625 V x 2,110 A

Power = 1,317,500 W

Therefore, the power consumption of the electric train is 1,317,500 W.

Learn more about Power:

https://brainly.com/question/2248465

#SPJ11

Not enough information. The voltmeter needs to be connected in parallel with the resistor to measure the voltage across the resistor.

A voltmeter is an electrical instrument for measuring the potential difference, or voltage, between two points in an electrical circuit. It is used to measure the voltage of a battery, a generator, or any other source of electrical potential. The voltmeter consists of an electrometer, which is an instrument that measures electrical potential, and a scale that reads out the voltage. The voltage is measured in volts, and the instrument is usually calibrated to read in units of millivolts or kilovolts. The operation of the voltmeter can be explained by Ohm’s Law, which states that the voltage in an electrical circuit is proportional to the current in the circuit. When the voltage is measured, a current is induced in the circuit, and the electrometer measures the potential difference between the two points. The voltmeter is a key instrument for any electrical engineer, as it is used to measure the voltage of a power source or the efficiency of an electrical circuit.

To learn more about voltmeter
https://brainly.com/question/29475578
#SPJ1

The energy of a charged capacitor can also be written as [tex]U = \frac {CV^2}{2}[/tex] and [tex]U = \frac {Q^2d}{2\epsilon_o A}[/tex].

To derive two more formulas for the energy of a charged capacitor, we start with the definition of capacitance:

C = Q/V

Solving for Q, we get:

Q = CV

Substituting this expression for Q into the original formula for the energy of a charged capacitor, [tex]U = QV/2[/tex], we get:

[tex]U = (CV)V/2[/tex]

[tex]U = CV^2/2[/tex]

This is one of the additional formulas for the energy of a charged capacitor.

Next, we can use the formula for the capacitance of a parallel-plate capacitor to derive the energy density associated with an electric field. The capacitance of a parallel-plate capacitor is given by:

[tex]C = \epsilon _o A/d[/tex]

where εo is the permittivity of free space, A is the area of each plate, and d is the distance between the plates. Solving this equation for the potential difference, V, we get:

[tex]V = Q/C[/tex]

[tex]V = Q/(\epsilon_o A/d)[/tex]

[tex]V = Qd/(\epsilon_o A)[/tex]

Substituting this expression for V into the formula for the energy of a charged capacitor, [tex]U = QV/2[/tex], we get:

[tex]U = \frac {Q^2d}{2\epsilon_o A}[/tex]

This expression gives us the energy associated with the electric field in the capacitor.

Learn more about capacitors:

https://brainly.com/question/21851402

#SPJ11

If an electric wire is allowed to produce a magnetic field no larger than that of the earth (0.50 x 10-4 t) at a distance of 15 cm from the wire,  the maximum current the wire can carry  is 1.8 A.

The maximum current the wire can carry is 1.8 A.

The formula to calculate the magnetic field due to a current-carrying wire is given by,

B = μ₀I/(2πr)

Here, B = maximum magnetic field = 0.50 × 10⁻⁴ T

μ₀ = permeability of free space = 4π × 10⁻⁷ T m/II = current in the wirer = distance from the wire = 15 cm = 0.15 m

Putting the given values in the formula,

0.50 × 10⁻⁴ T

= 4π × 10⁻⁷ T m/I × (2π × 0.15 m)

Solving for I, we get,

I = 1.8 A

Therefore, the maximum current the wire can carry is 1.8 A.

For more such questions on current , Visit:

https://brainly.com/question/1100341

#SPJ11

The correct answer is that solar energy is also known as isolation.

Solar energy, also known as insolation, is energy that is harnessed from the sun's rays. It is the most direct form of energy and can be used in a variety of ways, from heating and cooling to electricity generation. Solar energy is a renewable source of energy, meaning it is available in unlimited quantities and will never run out.


Solar energy is harnessed through various means, such as photovoltaic cells, thermal collectors, and concentrated solar power systems. Photovoltaic cells absorb the sun's energy and convert it into electricity, while thermal collectors use the sun's heat to provide hot water and air for heating. Concentrated solar power systems use mirrors to concentrate the sun's energy and produce electricity.


Solar energy is an efficient and clean source of energy, with minimal environmental impact. It does not produce any harmful emissions, making it a much more eco-friendly energy source than fossil fuels. Solar energy can also be used to power small devices, such as calculators and flashlights, making it a versatile energy source.

Therefore, the correct answer is isolation.

To know more about solar energy, refer here:

https://brainly.com/question/9704099#

#SPJ4