Answer:
2.1 rad(anticlockwise).
Explanation:
So, we are given the following data or parameters or information in the question above:
=> "The torsional stiffness of the spring support is k = 50 N m/rad. "
=> "If a concentrated torque of mag- nitude Ta = 500 Nm is applied in the center of the bar"
=> "L = 300 mm Assume a shear modu- lus G = 10 kN/mm2 and polar monnent of inertia J = 2000 mln"
Hence;
G × J = 10 kN/mm2 × 2000 mln = 20 Nm^2.
Also, L/2 = 300 mm /2 = 0.15 m (converted to metre).
==> 0.15/20 (V - w) + θ = 0.
==> 0.15/20 (V - w ) = -θ.
Where V = k = 50 N m/rad
w = 183.3 θ.
Therefore, w + Vθ = 500 Nm.
==> 183.3 + 50 θ = 500 Nm.
= 6.3
Anticlockwise,
θ = 2.1 rad.
An automotive air conditioner produces a 1-kW cooling effect while consuming 0.75 kW of power. What is the rate at which heat is rejected from this air conditioner
Answer:
The rejected by the air conditioning system is 1.75 kilowatts.
Explanation:
A air conditioning system is a refrigeration cycle, whose receives heat from cold reservoir with the help of power input before releasing it to hot reservoir. The First Law of Thermodynamics describes the model:
[tex]\dot Q_{L} + \dot W - \dot Q_{H} = 0[/tex]
Where:
[tex]\dot Q_{L}[/tex] - Heat rate from cold reservoir, measured in kilowatts.
[tex]\dot Q_{H}[/tex] - Heat rate liberated to the hot reservoir, measured in kilowatts.
[tex]\dot W[/tex] - Power input, measured in kilowatts.
The heat rejected is now cleared:
[tex]\dot Q_{H} = \dot Q_{L} + \dot W[/tex]
If [tex]\dot Q_{L} = 1\,kW[/tex] and [tex]\dot W = 0.75\,kW[/tex], then:
[tex]\dot Q_{H} = 1\,kW + 0.75\,kW[/tex]
[tex]\dot Q_{H} = 1.75\,kW[/tex]
The rejected by the air conditioning system is 1.75 kilowatts.
You are in the frozen food section of the grocery store and you notice that your hand gets cold when you place it on the glass windows of the display cases. Your friend says this is because coolness is transferred from the display case to your hand. What do you think?
Answer:
I think my friend got it all wrong, as coolness can not be transferred but heat was actually transferred between my hand and the glass windows
Explanation:
In thermodynamics, coolness can not be transferred, only heat can be transferred
Here is how the mechanism of why i felt cold works, my body gave out heat, hence there was heat transfer from a region of high to a low heat region, equilibrium was reached and I started feeling the coolness in my hands.
In your words, describe how momentum is related to energy.
Answer:
you need momentum in order to release energy. For example, if you need to push something heavy and you get a running head start, then it will be easier.
Explanation:
You throw a stone vertically upward with a speed of 26.0 m/s. (a) How fast is it moving when it reaches a height of 15.0 m? (b) How much time is required to reach this height when it's falling down? a. 19.5 m/s , b. 4.51 s a. 17.9 m/s , b. 0.620 s a. 19.5 m/s , b. 0.800 s a. 17.9 m/s , b. 4.28 s a. 380 m/s , b. 8 s
Answer:
ok well
Explanation:
teghe
Answer:
v = 19.5 m/s
t = 4.51 s
Explanation:
a)
given:
height is 15m from the ground
initial velocity Vi = 26 m/s
acceleration a or g = 9.81 m/s²
formula: Vf² = Vi² + 2aΔy
26² = Vi² + 2 (9.81) 15
Vi = 19.5 m/s
now you can calculate the time by using the equations below:
Δy = 1/2 (Vi + Vf) t
Vf = Vi + a t
Δy = Vi t + 1/2 a t
time must be 4.51 s
which of the following is a physical change?
A. a newspaper burns when placed in a fire.
B.an iron chair rusts when left outside
C.a sample of water boils and releases gas.
D.a plant changes carbon dioxide and water into sugar
Each of the boxes starts at rest and is then pulled for 2.0 m across a level, frictionless floor by a rope with the noted force. Which box has the highest final speed
Answer:
Explanation:
d
At a certain instant the current flowing through a 5.0-H inductor is 3.0 A. If the energy in the inductor at this instant is increasing at a rate of 3.0 J/s, how fast is the current changing
Answer:
The current is changing at the rate of 0.20 A/s
Explanation:
Given;
inductance of the inductor, L = 5.0-H
current in the inductor, I = 3.0 A
Energy stored in the inductor at the given instant, E = 3.0 J/s
The energy stored in inductor is given as;
E = ¹/₂LI²
E = ¹/₂(5)(3)²
E = 22.5 J/s
This energy is increased by 3.0 J/s
E = 22.5 J/s + 3.0 J/s = 25.5 J/s
Determine the new current at this given energy;
25.5 = ¹/₂LI²
25.5 = ¹/₂(5)(I²)
25.5 = 2.5I²
I² = 25.5 / 2.5
I² = 10.2
I = √10.2
I = 3.194 A/s
The rate at which the current is changing is the difference between the final current and the initial current in the inductor.
= 3.194 A/s - 3.0 A/s
= 0.194 A/s
≅0.20 A/s
Therefore, the current is changing at the rate of 0.20 A/s.
The rate at which the current is changing is;
di/dt = 0.2 A/s
We are given;
Inductance; L = 5 H
Current; I = 3 A
Rate of Increase of energy; dE/dt = 3 J/s
Now, the formula for energy stored in inductor is given as;
E = ¹/₂LI²
Since we are looking for rate at which current is changing, then we differentiate both sides of the energy equation to get;
dE/dt = LI (di/dt)
Plugging in the relevant values gives;
3 = (5 × 3)(di/dt)
di/dt = 3/(5 × 3)
di/dt = 0.2 A/s
Read more at; https://brainly.com/question/13112120
Recent technological developments like high-resolution satellite imagery and diagnostic positron emission tomography (PET scans) have refined and extended the camera’s capacity to provide information. Which passage assertion does this information support most strongly?
Answer:
D) Photography can be used to both control and benefit society.
Explanation:
High-resolution satellite imagery and diagnostic positron emission tomography (PET scans) have been used to both control and benefits the society in the sense that it has helped to take records of information of crime, traffic offenders such drunk drivers and over speeding drivers, e.t.c. it helps control by given their information and automatically penalizing them or ensuring the agency penalized them and also benefit the society by preventing people from committing crime thereby, protecting them from offenders.
Consider the following three objects, each of the same mass and radius:
(1) a solid sphere
(2) a solid disk
(3) a hoop
All three are released from rest at the top of an inclined plane. The three objects proceed down the incline undergoing rolling motion without slipping. Use work-kinetic energy theorem to determine which object will reach the bottom of the incline first.
a) 1, 2, 3
b) 2, 3, 1
c) 3, 1, 2
d) 3, 2, 1
e) All three reach the bottom at the same time.
Answer:
Explanation:a 1
A scientist is testing the seismometer in his lab and has created an apparatus that mimics the motion of the earthquake felt in part (a) by attaching the test mass to a spring. If the test mass weighs 13 N, what should be the spring constant of the spring the scientist use to simulate the relative motion of the test mass and the ground from part (a)?
Complete Question
The complete question is shown on the first uploaded image
Answer:
a
[tex]a_{max} = 0.00246 \ m/s^2[/tex]
b
[tex]k =722.2 \ N/m[/tex]
Explanation:
From the question we are told that
The amplitude is [tex]A = 1.8 \ cm = 0.018 \ m[/tex]
The period is [tex]T = 17 \ s[/tex]
The test weight is [tex]W = 13 \ N[/tex]
Generally the radial acceleration is mathematically represented as
[tex]a = w^2 r[/tex]
at maximum angular acceleration
[tex]r = A[/tex]
So
[tex]a_{max} = w^2 A[/tex]
Now [tex]w[/tex] is the angular velocity which is mathematically represented as
[tex]w = \frac{2 * \pi }{T}[/tex]
Therefore
[tex]a_{max} = [\frac{2 * \pi}{T} ]^2 * A[/tex]
substituting values
[tex]a_{max} = [\frac{2 * 3.142}{17} ]^2 * 0.018[/tex]
[tex]a_{max} = 0.00246 \ m/s^2[/tex]
Generally this test weight is mathematically represented as
[tex]W = k * A[/tex]
Where k is the spring constant
Therefore
[tex]k = \frac{W}{A}[/tex]
substituting values
[tex]k = \frac{13}{0.018}[/tex]
[tex]k =722.2 \ N/m[/tex]
Balls A and B attract each other gravitationally with a force of magnitude F at distance R. If we triple the mass of ball B and triple the separation of the balls to 3R, what is the magnitude of their attractive force now
Answer:
F₂ = 1/3 FExplanation:
Using the law of gravitation of force to solve this question. The law states that the Force of attraction between two masses is directly proportional to the product of their masses and inversely proportional to the square of the distances between them.
Mathematically, F = GMaMb/R² ... 1
G is the gravitational constant
Ma and Mb are the masses of the balls
R is the distance between the balls
If the mass of ball B is tripled and the magnitude of the separation of the balls is increased to 3R, the force between them will be;
F₂ = GMa(3Mb)/(3R)²
F₂ = 3GMaMb/9R² ... 2
Dividing equation 1 by 2 we will have;
F₂/F = (3GMaMb/9R²)/GMaMb/R²
F₂/F = 3GMaMb/9R² * GMaMb/R²
F₂/F = 3/9
F₂/F = 1/3
F₂ = 1/3 F
This shows that the magnitude of the new attractive force is one-third that of the initial attractive force
As more energy from fossil fuels and other fuels is released on Earth, the overall temperature of Earth tends to rise. Discuss how temperature equilibrium explains why Earth’s temperature cannot rise indefinitely.
Answer:
processes are competitive and reach a thermal equilibrium where the absorbed energy is equal to the energy emitted, this is the equilibrium temperature of the planet.
Explanation:
The temperature of planet Earth is due to two main types of process, internal and external.
Internal processes are all chemical processes that occur that release heat into the environment or due to gases that trap heat on the planet, greenhouse effect
External processes is heating due to energy coming from the Sun. This includes direct heating of the surface by the absorption of energy and reflects of energy in different atmospheric layers.
These are the two terms that heat the Earth
In addition there are several processes so the planet loses energy,
* energy radiation to outer space that is a few degrees kelvin, for which there is a permanent emission
* endothermic processes that need to absorb heat to perform, this lowers the temperature of the system
* liquid (water) system that absorbs large amounts of heat to change state and temperature.
These processes are competitive and reach a thermal equilibrium where the absorbed energy is equal to the energy emitted, this is the equilibrium temperature of the planet.
Therefore it is impossible for the temperature to increase indefinitely since the emission would increase by decreasing the value
On a certain planet a body is thrown vertically upwards with an initial speed of 40 m / s. If the maximum height was 100 m, the acceleration due to gravity is
a) 15 m / s 2
b) 12.5 m / s 2
c) 8 m / s 2
d) 10 m / s 2
Answer:
C) 8 m/s²
Explanation:
Given:
v₀ = 40 m/s
v = 0 m/s
Δy = 100 m
Find: a
v² = v₀² + 2aΔy
(0 m/s)² = (40 m/s)² + 2a (100 m)
a = -8 m/s²
An air-filled capacitor is formed from two long conducting cylindrical shells that are coaxial and have radii of 42 mm and 74 mm. The electric potential of the inner conductor with respect to the outer conductor is -308 V ( = 1/4πε0 = 8.99 × 10^9 N · m^2/C^2).
The maximum energy density of the capacitor is closest to:_______
Correct answer is 2.7 x 10^-3 J/m3
I hope that helps ! <33
The maximum energy density of the capacitor is closest to: 2.7 x 10^-3 J/m3.
What is meant by the energy density of a capacitor?Energy density is defined as the total energy per unit volume of the capacitor. Since, Now, for a parallel plate capacitor, A × d = Volume of space between plates to which electric field E = V / d is confined. Therefore, Energy is stored per unit volume.
How do you calculate energy density?All Answers (14) Energy density is equal to 1/2*C*V2/weight, where C is the capacitance you computed and V should be your nominal voltage (i.e 2.7 V). Power Density is V2/4/ESR/weight, where ESR is the equivalent series resistance.
Learn more about energy density at
https://brainly.com/question/13035557
#SPJ2
A 7.0-kg shell at rest explodes into two fragments, one with a mass of 2.0 kg and the other with a mass of 5.0 kg. If the heavier fragment gains 100 J of kinetic energy from the explosion, how much kinetic energy does the lighter one gain?
Answer:
39.94m/s.Explanation:
Kinetic energy is expressed as KE = 1/2 mv² where;
m is the mass of the body
v is the velocity of the body.
For the heavier shell;
m = 5kg
KE gained = 100J
Substituting this values into the formula above to get the velocity v;
100 = 1/2 * 5 * v²
5v² = 200
v² = 200/5
v² = 40
v = √40
v = 6.32 m/s
Note that after the explosion, both body fragments will possess the same velocity.
For the lighter shell;
mass = 2.0kg and v = 6.32m/s
KE of the lighter shell = 1/2 * 2 * 6.32²
KE of the lighter shell = 6.32²
KE of the lighter shell= 39.94m/s
Hence, the lighter one gains a kinetic energy of 39.94m/s.
The gain in the kinetic energy of the smaller fragment is 249.64 J.
The given parameters;
Mass of the shell, m = 7.0 kgMass of one fragment, m₁ = 2.0 kgMass of the second fragment, m₂ = 5.0 kgKinetic energy of heavier fragment, K.E₁ = 100 JThe velocity of the heavier fragment is calculated as follows;
[tex]K.E = \frac{1}{2} mv^2\\\\mv^2 = 2K.E\\\\v^2 = \frac{2K.E}{m} \\\\v= \sqrt{\frac{2K.E}{m} } \\\\v = \sqrt{\frac{2 \times 100}{5} }\\\\v = 6.32 \ m/s[/tex]
Apply the principle of conservation of linear momentum to determine the velocity of the smaller fragment as;
[tex]m_1 u_1 + m_2 u_2 = v(m_1 + m_2)\\\\-6.32(5) \ + 2u_2 = 0(7)\\\\-31.6 + 2u_2 = 0\\\\2u_2 = 31.6\\\\u_2 = \frac{31.6}{2} \\\\u_2 = 15.8 \ m/s[/tex]
The gain in the kinetic energy of the smaller fragment is calculated as follows;
[tex]K.E_2 = \frac{1}{2} mu_2^2\\\\K.E_2 = \frac{1}{2} \times 2 \times (15.8)^2\\\\K.E_2 = 249.64 \ J[/tex]
Thus, the gain in the kinetic energy of the smaller fragment is 249.64 J.
Learn more about conservation of linear momentum here: https://brainly.com/question/7538238
g A tube open at both ends, resonated at it's fundamental frequency, to a sound wave traveling at 330m/s. If the length of the tube is 4cm, find the frequency of the sound wave.
Answer:
frequency =4125Hz
Explanation:
L = 4cm = 0.04m
f =v/2L
f = 330/2 x 0.04
f = 4125Hz
In your own words, discuss how energy conservation applies to a pendulum. Where is the potential energy the most? Where is the potential energy the least? Where is kinetic energy the most? Where is kinetic energy the least?
Answer:
Explanation:
Energy conservation applies to the swinging of pendulum . When the bob is at one extreme , it is at some height from its lowest point . So it has some gravitational potential energy . At that time since it remains at rest its kinetic energy is zero or the least . As it goes down while swinging , its potential energy decreases and kinetic energy increases following conservation of mechanical energy . At the At the lowest point , its potential energy is least and kinetic energy is maximum .
In this way , there is conservation of mechanical energy .
Suppose you are looking into the end of a long cylindrical tube in which there is a uniform magnetic field pointing away from you. If the magnitude of the field is decreasing with time the direction of the induced magnetic field is
Answer:
If the magnitude of the field is decreasing with time the direction of the induced magnetic field is CLOCKWISE
Explanation
This is because If the magnetic field decreases with time, the electric field will be produced in order to oppose the change in line with lenz law. Thus The right hand rule can be applied to find that the direction of electric field is in the clockwise direction.
Diamagnetic materialsA) have small negative values of magnetic susceptibility.B) are those in which the magnetic moments of all electrons in each atom cancel.C) experience a small induced magnetic moment when placed in an external magnetic field.D) exhibit the property of diamagnetism independently of temperature.E)are described by all
Answer:
C) experience a small induced magnetic moment when placed in an external magnetic field.
Explanation:
Diamagnetics materials are those that experience a small induced magnetic moment when placed in an external magnetic field. These materials, such as bismuth, copper, silver and lead, have elementary magnets in their compositions. When they are exposed to an external magnetic cap, these elemental magnets tend to follow an orientation contrary to the external magnetic field. As a result, a magnetic field is created in the opposite direction to the external magnetic field.
An ideal air-filled parallel-plate capacitor has round plates and carries a fixed amount of equal butopposite charge on its plates. All the geometric parameters of the capacitor (plate diameter andplate separation) are now DOUBLED. If the original energy stored in the capacitor was U0, howmuch energy does it now store?
Answer:
U_f = (U_o)/2)
Explanation:
The capacitance of a given capacitor is given by the formula;
C = ε_o•A/d
While energy stored in plates capacitor is given as; U_o = Q²/2C
Now,we are told that that all the dimensions of the capacitor plate is doubled. Thus, we now have;
C' = ε_o•4A/2d
Hence, C' = 2C
so capacitance is now doubled
Thus, the final energy stored between the plates of capacitor is given as;
U_f = Q²/2C'
From earlier, we saw that C' = 2C.
Thus;
U_f = Q²/2(2C)
U_f = Q²/4C
Rearranging, we have;
U_f = (1/2)(Q²/2C)
From earlier, U_o = Q²/2C
Hence,
U_f = (1/2)(U_o)
Or
U_f = (U_o/2)
A person can survive a feet-first impact at a speed of about 12 m/s (27 mi/h) on concrete, 15 m/s (34 mi/h) on soil, and 34 m/s (76 mi/h) on water. What is the reason for the different values for different surfaces
Answer:
Different surfaces have different impact force during collision which depends on the time it takes the person to come to rest after collision.
Explanation:
Given;
speed on concrete = 12 m/s (27 mi/h)
speed on soil = 15 m/s (34 mi/h)
speed on water = 34 m/s (76 mi/h)
The impact force on this person during collision is rate of change of momentum;
[tex]F = \frac{\delta P}{\delta t}[/tex]
During collision, the force exerted on this person depends on how long the collision lasts; that is, how long it takes for this person to come to rest after collision with each of the surfaces.
The longer the time of collision, the smaller the force exerted by each.
It takes shorter time for the person to come to rest on concrete surface than on soil surface, also it takes shorter time for the person to come to rest on soil surface than on water surface.
As a result of the reason above, the force exerted on the person during collision by the concrete surface is greater than that of soil surface which is greater than that of water surface.
If you have completely polarized light of intensity 125 W/m2, what will its intensity be after passing through a polarizing filter with its axis at an 89.5° angle to the light's polarization direction?
Answer:
When we have completely polarized light with intensity I0, and it passes through a polarizing filter with its axis at an angle θ with respect to the light's polarization direction, the new intensity of the light will be:
I = I0*cos^2(θ)
This is called the "Malus' law".
in this case, we have:
I0 = 125 W/m^2
θ = 89.5°
then:
I = (125 W/m^2)*cos^2(89.9°) = 0.00038 W/m^2
A 269-turn solenoid is 102 cm long and has a radius of 2.3 cm. It carries a current of 3.9 A. What is the magnetic field inside the solenoid near its center?
Answer:
Magnitude of the magnetic field inside the solenoid near its centre is 1.293 x 10⁻³ T
Explanation:
Given;
number of turns of solenoid, N = 269 turn
length of the solenoid, L = 102 cm = 1.02 m
radius of the solenoid, r = 2.3 cm = 0.023 m
current in the solenoid, I = 3.9 A
Magnitude of the magnetic field inside the solenoid near its centre is calculated as;
[tex]B = \frac{\mu_o NI}{l} \\\\[/tex]
Where;
μ₀ is permeability of free space = 4π x 10⁻⁷ m/A
[tex]B = \frac{4\pi*10^{-7} *269*3.9}{1.02} \\\\B = 1.293 *10^{-3} \ T[/tex]
Therefore, magnitude of the magnetic field inside the solenoid near its centre is 1.293 x 10⁻³ T
The intensity of sunlight at the Earth's distance from the Sun is 1370 W/m2. (a) Assume the Earth absorbs all the sunlight incident upon it. Find the total force the Sun exerts on the Earth due to radiation pressure. N (b) Explain how this force compares with the Sun's gravitational attraction.
Answer:
F= 3.56e22N
Explanation:
Using the force of radiation acting on the earth which is
force = radiation pressure x area = (intensity/c)xpi R^2
force = 1370W/m^2 x pi x( 6.37x10^6m)^2/3x10^8m/s
force = 5.82x10^8 N
But the sun's gravitational attraction means the magnitude of the solar gravitational force on earth: If that's the case, the answer is approx 10^22 N:
F=GMm/r^2
G=6.67x10^(-11)=6.67e-11
M=mass sun = 2x10^30kg=2e30
m=mass earth = 6x10^24kg
r=earth sun distance = 1.5x10^11m
F=(6.6e-11)(2e30)(6e24)/(1.5e11)^2 =
F= 3.56e22N
Why would physics be used to study light emitted by a star?
O A. Stars form interesting shapes in the sky.
B. Light is very pretty.
O C. The positions of stars control our lives.
O D. Light is a form of energy.
Answer:
O D.
Explanation:
Physics has an aspect that deals with the study of energy
Answer:
D. Light is a form of energy
Explanation:
A 0.2 kg rubber ball is dropped from the window of a building. It strikes the sidewalk below at 30 m/s and rebounds at 20 m/s. The magnitude of the change in momentum of the ball as a result of the collision with the sidewalk is _______.
Answer:
10 kgm/s
Explanation:
Change in momentum: This can be defined as the product of mass and change in velocity. The S.I unit of change in momentum is Kgm/s.
From the question,
ΔM = m(v-u)...................... Equation 1
Where ΔM = change in momentum, u = initial velocity, v = final velocity.
Note: Let upward direction be negative, and downward direction be positive.
Given: m = 0.2 kg, v = -20 m/s, u = 30 m/s
Substitute into equation 1
ΔM = 0.2(-20-30)
ΔM = 0.2(-50)
ΔM = -10 kgm/s.
The negative sign shows that the change in momentum is Upward
The magnitude of the change in momentum of the ball as a result of the collision with the sidewalk is -10 kg-m/s.
Given data:
The mass of rubber ball is, m = 0.2 kg.
The initial speed of ball is, u = 30 m/s.
The final rebounding speed of ball is, v = - 20 m/s ( Negative sign shows that during the rebounding, the ball changes its direction)
The momentum of any object is defined as the product of mass and change in velocity. The S.I unit of momentum is Kg-m/s. And the expression for the change in momentum is given as,
[tex]p= m ( v-u)[/tex]
Solving as,
[tex]p= 0.2 \times ( -20-30)\\\\p=-10 \;\rm kg.m/s[/tex]
Thus, we can conclude that the magnitude of the change in momentum of the ball as a result of the collision with the sidewalk is -10 kg-m/s.
Learn more about the change in momentum here:
https://brainly.com/question/904448
An inductor is connected to the terminals of a battery that has an emf of 12.0 V and negligible internal resistance. The current is 4.86 mA at 0.700 ms after the connection is completed. After a long time the current is 6.80 mA.
What are
(a) the resistance R of the inductor and
(b) the inductance L of the inductor?
Answer:
a) 1764.71 ohms
b) 1.73 H
Explanation:
From the question, we can identify the following parameters;
Vo =12 V , i = 4.86 mA, t =0.700 ms, io =6.80 mA
(a) Indcued emf V = L di/dt =0
From ohms law Vo = ioR
R = 12/6.80*0.001
R=1764.71 ohms
(b) For LR circuit
i =io (1-e^-t/T)
Time constant T = L/R
4.86 = 6.80 (1-e^-0.7*10^-3/T)
divide both side by 6.8
0.715 = 0.0007/T
L/R = 0.0007/0.715
L/R = 0.000979020979
Substitute R from above
L = 0.000979020979 * 1764.71
L =1.73 H
Two unknown resistors are connected together. When they are connected in series their equivalent resistance is 15 Ω. When they are connected in parallel, their equivalent resistance is 3.3 Ω. What are the resistances of these resistors?
Explanation:
Let x and y are two unknown resistors. When they are connected in series their equivalent resistance is 15 Ω. When they are connected in parallel, their equivalent resistance is 3.3 Ω.
For series combination,
[tex]x+y=15[/tex] ......(1)
For parallel combination,
[tex]\dfrac{1}{x}+\dfrac{1}{y}=3.3[/tex] ....(2)
We need to find the resistances of these resistors. Solving equation (1) and (2) we get :
x = 0.29 and y = 14.7
Hence, the resistances of these resistors are 0.29 ohms and 14.7 ohms.
Chameleons catch insects with their tongues, which they can rapidly extend to great lengths. In a typical strike, the chameleon's tongue accelerates at a remarkable 210 m/s^2 for 20 ms, then travels at constant speed for another 30 ms.
During this total time of 50 ms, 1/20 of a second, how far does the tongue reach?
Express your answer to two significant figures and include the appropriate units.
Answer:
x_total = 0.17m
Explanation:
We can treat this exercise with the kinematics equations, where in the first part it is accelerated and in the second it is a uniform movement.
Let's analyze accelerated motion
The time that lasts is t = 20 10⁻³ s, the initial speed is zero (v₀ = 0), let's find the length that advances
x₁ = v₀ t + ½ a t²
x₁ = ½ a t²
x₁ = ½ 210 (20 10⁻³)²
x₁ = 4.2 10⁻² m
let's find the speed for the end of this movement
v = v₀ + a t
v = 0 + 210 20 10⁻³
v = 4.2 m / s
with this speed we can find the distance that the uniform movement
x₂ = v t2
x₂ = 4.2 30 10⁻³
x₂ = 1.26 10⁻¹ m
x₂ = 0.126m
the total distance traveled is
x_total = x₁ + x₂
x_total = 0.0420 +0.126
x_total = 0.168m
Let's reduce the significant figures to two
x_total = 0.17m
Si se deja caer una piedra desde un helicóptero en reposo, entonces al cabo de 20 s cual será la rapidez y la distancia recorrida por la piedra
Answer:
La piedra alcanza una rapidez de 196.14 metros por segundo y una distancia recorrida de 1961.4 metros en 20 segundos.
Explanation:
Si se excluye los efectos del arrastre por la viscosidad del aire, la piedra experimenta un movimiento de caída libre, es decir, que la piedra es acelerada por la gravedad terrestre. La distancia recorrida y la rapidez final de la piedra pueden obtenerse con la ayuda de las siguientes ecuaciones cinemáticas:
[tex]v = v_{o} + g\cdot t[/tex]
[tex]y - y_{o} = v_{o}\cdot t + \frac{1}{2}\cdot g \cdot t^{2}[/tex]
Donde:
[tex]v[/tex], [tex]v_{o}[/tex] - Rapideces final e inicial de la piedra, medidas en metros por segundo.
[tex]t[/tex] - Tiempo, medido en segundos.
[tex]g[/tex] - Aceleración gravitacional, medida en metros por segundo al cuadrado.
[tex]y[/tex]. [tex]y_{o}[/tex] - Posiciones final e inicial de la piedra, medidos en metros.
Si [tex]v_{o} = 0\,\frac{m}{s}[/tex], [tex]g = -9.807\,\frac{m}{s^{2}}[/tex], [tex]y_{o} = 0\,m[/tex], entonces:
[tex]v = 0\,\frac{m}{s} +\left(-9.807\,\frac{m}{s^{2}} \right) \cdot (20\,s)[/tex]
[tex]v = -196.14\,\frac{m}{s}[/tex]
[tex]y-y_{o} = \left(0\,\frac{m}{s} \right)\cdot (20\,s) + \frac{1}{2}\cdot \left(-9.807\,\frac{m}{s^{2}} \right) \cdot (20\,s)^{2}[/tex]
[tex]y-y_{o} = -1961.4\,m[/tex]
La piedra alcanza una rapidez de 196.14 metros por segundo y una distancia recorrida de 1961.4 metros en 20 segundos.