an emf source with a resistor with and a capacitor with are connected in series. as the capacitor charges, when the current in the resistor is 0.900 a, what is the magnitude of the charge on each plate of the capacitor?

v_max = √(2kq1q2 / (md))

To determine the speed of the protons when they reach their original separation after being released from rest at the closer distance, we can use the principle of conservation of mechanical energy.

According to the given problem, the protons are initially at rest at a closer distance. This means they have zero initial kinetic energy (KE) and only potential energy (PE) due to their separation.

As they move towards each other under the influence of electrostatic force, their potential energy is converted into kinetic energy.

At the original separation, the protons would have reached their maximum kinetic energy, as all of the potential energy would have been converted into kinetic energy. Let's denote this maximum kinetic energy as KE_max.

The total mechanical energy (E) of the protons, which is the sum of their kinetic energy and potential energy, remains constant throughout their motion. So we have:

E = KE + PE

At the original separation, KE = KE_max and PE = 0, as the protons have zero potential energy at that point.

So we can write:

E = KE_max + 0

E = KE_max

Now, let's denote the speed of the protons at the original separation as v_max. We can use the formula for kinetic energy:

KE = 1/2 mv^2

where m is the mass of the proton and v is its speed. Substituting KE_max for E and v_max for v, we have:

KE_max = 1/2 m v_max^2

Since the protons have no initial kinetic energy, their total mechanical energy E is equal to their initial potential energy PE, which is given by the equation:

PE = kq1q2 / d

where k is the electrostatic constant, q1 and q2 are the charges of the protons, and d is their initial separation (closer distance in part a).

Now, if we equate the expressions for KE_max and PE, we get:

1/2 m v_max^2 = kq1q2 / d

Solving for v_max, we have:

v_max = √(2kq1q2 / (md))

where √ denotes the square root.

So, to find the speed of the protons when they reach their original separation, you would need to know the values of the electrostatic constant (k), the charges of the protons (q1 and q2), the mass of the proton (m), and the initial separation (d), and then plug these values into the equation above to calculate v_max.

To learn more about kinetic energy, refer below:

https://brainly.com/question/26472013

#SPJ11

A circuit that minimizes resistance will be able to carry the maximum amount of current.

What is Current?

It is defined as the amount of electric charge passing through a given point in a circuit in unit time. The SI unit of electric current is the ampere (A), which is defined as one coulomb of electric charge per second. Electric current can be either direct current (DC), which flows in one direction only, or alternating current (AC), which changes direction periodically.

Based on the results of this activity, a circuit that would carry the maximum amount of electric current should have:

High voltage: A higher voltage will cause a greater potential difference and push more electrons through the circuit.

Thicker wire diameter: A thicker wire diameter will have lower resistance, allowing more current to flow through the wire.

Shorter wire length: A shorter wire length will have lower resistance, allowing more current to flow through the wire.

Lower wire temperature: A lower wire temperature will have lower resistance, allowing more current to flow through the wire.

Learn more about  Current from given link

https://brainly.com/question/1100341

#SPJ1

To determine g, you must graph distance vs. time squared. When you draw a straight line that passes through the origin of this graph, you can use the slope of the line to determine the acceleration due to gravity g.

To yield a straight line whose slope could be used to calculate a numerical value for the acceleration due to gravity g, the quantity that should be graphed on the vertical axis is the distance (d) and the quantity that should be graphed on the horizontal axis is the time (t). Gravity acceleration, denoted by the letter "g," is the rate at which a falling object increases its speed. A constant acceleration is generated by gravity acceleration, and it is used to describe falling bodies. In any experiment to determine the acceleration due to gravity g, the distance an object travels over a period of time must be measured, recorded, and plotted.

The equation to use for measuring the distance d is: d = 1/2gt^2. The above equation shows that distance d depends on the time t and gravity acceleration g. We can rewrite the equation to give the acceleration due to gravity g by dividing both sides by t^2:g = 2d/t^2. Therefore, to determine g, you must graph distance vs. time squared.

Learn more about acceleration : https://brainly.com/question/26408808

#SPJ11

The frequency of a wave with a wavelength of 635 nm is approximately 4.72 x 10¹⁴ Hz.

The frequency of a wave is related to its wavelength by the formula:

v = fλ

where v is the speed of the wave (which for electromagnetic waves in vacuum is approximately equal to the speed of light, c),

f is the frequency, and

λ is the wavelength.

Rearranging this formula, we get:

f = v/λ

Substituting the values for the speed of light in vacuum (c = 3.00 x 10⁸ m/s) and the given wavelength

(λ = 635 nm = 635 x 10^⁻⁹ m), we get:

f = (3.00 x 10⁸ m/s) / (635 x 10⁻¹⁹ m) = 4.72 x 10¹⁴ Hz

Therefore, the frequency of a wave with a wavelength of 635 nm is approximately 4.72 x 10¹⁴ Hz.

To solve more questions about the wavelength:

https://brainly.com/question/25847009.

#SPJ11

To determine the capacitance of a teflon-filled parallel-plate capacitor having a plate area of 1.80[tex]cm^{2}[/tex] and a plate separation of 0.0200 mm, we can use the formula for capacitance: C = εo εr A/d, when the values are plugged in, the capacitance is found to be [tex]1.54* 10^{-9}[/tex] Farads.

The capacitance of a teflon-filled parallel-plate capacitor having a plate area of 1.80[tex]cm^{2}[/tex] and a plate separation of 0.0200 mm is determined using the formula C = εo A/d, where C is the capacitance, εo is the permittivity of free space, A is the area of the plates, and d is the distance between the plates.

To explain this calculation further, the permittivity of free space is a constant value equal to [tex]8.85 * 10^{-12}[/tex] A/d, which is derived from the equation εo = 1/ (μoc2), where μo is the permeability of free space, and c is the speed of light. The area of the plates is given in the problem statement as 1.80 [tex]cm^{2}[/tex], and the distance between the plates is given as 0.0200 mm.

When these values are plugged into the formula, the capacitance is found to be [tex]1.54* 10^{-9}[/tex]Farads. In conclusion, the capacitance of a teflon-filled parallel-plate capacitor having a plate area of 1.80 [tex]cm^{2}[/tex] and a plate separation of 0.0200 mm is 1.54 x 10-9 Farads.

For more questions related to capacitance.

https://brainly.com/question/28445252

#SPJ11

Jake's average velocity is 94.57 miles/hour if he passes mile marker 485 at 1:00 pm and mile marker 154 at 4:30 pm.

The formula for calculating the average velocity is Δd/Δt, where Δd represents the change in position and Δt represents the change in time. The change in position is the distance between the two-mile markers can be calculated as:-

485 miles - 154 miles = 331 miles.

The change in time is the difference between the two times can be calculated as:-

4:30 pm - 1:00 pm = 3.5 hours.

Now substitute the values into the formula:-

Average velocity = Δd/Δt = 331 miles / 3.5 hours = 94.57 miles per hour.

Therefore, Jake's average velocity is 94.57 miles per hour.

Learn more about average velocity: https://brainly.com/question/28668011

#SPJ11

The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire is 5.5 x 105 V/m.

The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire, we can use Ohm's law, which states that the voltage (V) equals the current (I) multiplied by the resistance (R).

Since the resistance of an iron wire is given by R=ρL/A, where ρ is the resistivity, L is the length of the wire, and A is its cross-sectional area, we can rearrange Ohm's law to get the voltage V=IR.

For the given wire, the cross-sectional area is A=πd2/4, where d is the diameter of the wire, the resistance to be R=ρL/(πd2/4).

V=IR, and rearranging to solve for I, we get I=V/R. The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire to be E=V/L=V/(ρL/A)=Vπd2/(4ρL).

The electric field strength needed for a given wire of any diameter and any length. However, for the given parameters, electric field strength to be E=6.0/(1.7 x 10-3 x 10-2/(4 x 10-7 x 8.0))=5.5 x 105 V/m.

The electric field strength needed to create a 6.0 A current in a 1.7-mm-diameter iron wire is 5.5 x 105 V/m.

to know more about electric field refer here:

https://brainly.com/question/15800304#

#SPJ11

The magnitude of the friction force is 0.788 N and it is directed to the right.

The friction force acting on the arrow is equal to the force required to stop the arrow and is directed opposite the direction of motion.

The magnitude of the friction force is equal to the product of the mass of the arrow (70.0 g) and the deceleration of the arrow (11.2 cm/s^2).

When the arrow hits the tree, the friction force of the tree will slow down the arrow's motion. The magnitude of this friction force is equal to the product of the mass of the arrow (70.0 g) and the deceleration of the arrow (11.2 cm/s^2).

The direction of the friction force will be opposite to the direction of the arrow's motion.

Therefore, the magnitude of the friction force is 0.788 N and it is directed to the right. This is because the arrow was fired to the left and the friction force must be equal and opposite in order to bring the arrow to a stop.

To know more about friction force click on below link:

https://brainly.com/question/30280752#

#SPJ11

The ball will reach a maximum height of 86 feet.

The ball is thrown vertically upward with an initial velocity of 50 feet per second.

Using the equation v2 = u2 + 2as, the maximum height that the ball will reach can be calculated as:

s = (v2 - u2) / 2a

where s is the maximum height, v is the final velocity, u is the initial velocity, and a is the acceleration due to gravity (9.81 m/s2).

Plugging in the values for u and v, we get s = (502 - 02) / 2(9.81) = 86 feet.


Therefore, the maximum height the ball will reach is 86 feet.

To know more about the maximum height click here:

https://brainly.com/question/11535666

#SPJ11

When the light of 258.0 nm strikes the metal surface, each ejected electron has a kinetic energy of 4.80 eV.

To calculate the kinetic energy, we use the formula:

Kinetic Energy (KE) = hc/λ, where h is Planck's constant (6.626×10⁻³⁴ Js), c is the speed of light (2.998x10⁸ m/s) and λ is the wavelength of the light (258.0 nm).

Therefore,

KE = (6.626x10⁻³⁴ Js)(2.998x10⁸ m/s) / (2.58x10^-7 m)

= 7.69x10⁻¹⁹ J = 4.80eV, where (1eV = 1.6 x 10⁻¹⁹ J)


Thus, each ejected electron has a kinetic energy of 4.80 eV or 7.69x10⁻¹⁹ J when the light of 258.0 nm strikes the metal surface.

To know more about kinetic energy, refer here:

https://brainly.com/question/11749818#

#SPJ11

If the car rounds an unbanked curve of radius 80 m and the coefficient of static friction between the road and car is 0.8, then the maximum speed at which the car traverses the curve without slipping is V =  25.05 m/s.

The maximum speed at which the car traverses the curve without slipping can be determined using the following formula:

[tex]v = \sqrt{(\mu rg)}[/tex]

Where:

v = maximum speed

μ = coefficient of static friction

r = radius of curvature

g = acceleration due to gravity

Substituting the given values into the formula:

[tex]v = \sqrt {(\mu rg)}[/tex]

[tex]v = \sqrt{(0.8 \times 80 \times 9.81)}[/tex]

v = 25.05 m/s

Therefore, the maximum speed at which the car can traverse the curve without slipping is 25.05 m/s.

Learn more about acceleration:

https://brainly.com/question/460763

#SPJ11

The car was traveling at a speed of 54.6 m/s (approximately 196.6 km/h) at the bottom of the valley.

The normal force on the driver is equal to the weight of the driver plus the weight of the car, which is twice the weight of the driver. This means that the total weight on the car is three times the weight of the driver.

Therefore, the centripetal force acting on the car is equal to three times the weight of the driver, which is equal to mv^2/r, where m is the mass of the car, v is the velocity of the car, and r is the radius of curvature.

Solving for v, we get v = √(3gr), where g is the acceleration due to gravity. Substituting the given values, we get v = √(3 x 9.81 x 95) = 54.6 m/s.

Therefore, the car was traveling at a speed of 54.6 m/s (approximately 196.6 km/h) at the bottom of the valley.

For more questions like Speed click the link below:

https://brainly.com/question/28224010

#SPJ11

The wavelength of the sinusoidal wave traveling along a rope is calculated to be 21.5 cm.

The wavelength of a sinusoidal wave is defined as the distance between two consecutive crests or troughs. It can be started by finding the frequency of the oscillator that generates the wave:

frequency = number of vibrations / time

frequency = 45.0 / 29.0 s = 1.55 Hz

After this, we can find the speed of the wave:

speed = distance / time

speed = 400 cm / 12.0 s = 33.3 cm/s

The speed of a sinusoidal wave on a rope is related to its frequency and wavelength by the equation:

speed = frequency x wavelength

Therefore, we can rearrange the equation to solve for wavelength:

wavelength = speed / frequency

wavelength = 33.3 cm/s / 1.55 Hz

wavelength = 21.5 cm

Therefore, the wavelength of the wave is 21.5 cm.

Learn more about wavelength :

https://brainly.com/question/28762766

#SPJ4

Well, materials may feel colder than others because they could:

So those are why they may feel colder

But . . .

Some items could be hotter becuase:

Those are my reasons why they can either be colder or hotter

One of the advantages of digital imaging is increased speed for viewing images.

Digital imaging is a technology that enables doctors to take X-rays, MRIs, CT scans, and other medical images, and store them digitally.

Digital imaging provides many advantages over traditional film-based imaging, such as increased speed for viewing images.

Digital imaging is a medical technology that allows physicians to take, store, and view medical images in digital form. Digital imaging includes modalities such as X-rays, computed tomography (CT), magnetic resonance imaging (MRI), and ultrasound.

Digital imaging provides several benefits, such as increased speed, improved diagnostic accuracy, lower radiation exposure, and reduced chemical usage. It also enables doctors to view images in real-time, making it easier to detect and diagnose medical conditions.

Additionally, digital images can be easily shared between medical professionals, allowing for better communication and collaboration.

The advantages of digital imaging include increased speed for viewing images. Instead of waiting for film-based images to be developed, doctors can view digital images instantly. This can be particularly important in emergency situations, where time is critical.

Digital imaging also allows doctors to manipulate images, zooming in or out as needed, to get a clearer view of the affected area or to identify specific features or abnormalities.

To know more about digital imaging, refer here:

https://brainly.com/question/321434#

#SPJ4

A. The waves can travel through empty space.

D. The waves can transfer energy through solids, liquids, and gases.

C. The waves transfer energy by causing particles of matter to move.

These waves transfer energy by causing particles of matter to move in the direction of the wave. This type of wave can travel through solids, liquids, and gases, but not through empty space.

There are two types of mechanical waves, longitudinal and transverse. Longitudinal waves are waves that travel in the same direction as the vibration of particles, while transverse waves travel perpendicular to the vibration of particles. An example of a longitudinal wave is a sound wave, while an example of a transverse wave is a water wave.

Mechanical waves are important to us as they are responsible for transferring energy through various mediums. For example, sound waves are propagated through the air and enable us to hear sound. This type of wave also transfers energy through solids, such as the vibrating strings of a guitar, and liquids, such as the waves of an ocean.

In conclusion, mechanical waves are waves that require matter to transfer energy and can transfer energy through solids, liquids, and gases. These waves travel in the same direction as the vibration of particles (longitudinal) or perpendicular to the vibration of particles (transverse). Mechanical waves are important to us as they transfer energy

Learn more about Mechanical waves here:

https://brainly.com/question/26116832

#SPJ1

Greenhouse gases are capable of absorbing: infrared radiation

Infrared radiation is a type of radiation affected by greenhouse gases. Greenhouse gases are capable of absorbing infrared radiation. Water vapor, carbon dioxide, and methane are the primary greenhouse gases. When the Earth receives energy from the sun, some of it is reflected and some is absorbed by the Earth.

The absorbed energy heats up the Earth's surface, which then radiates energy back out into the atmosphere in the form of infrared radiation. Greenhouse gases absorb some of this outgoing infrared radiation, which warms the atmosphere. This warming is known as the greenhouse effect.

The more greenhouse gases there are in the atmosphere, the more radiation they can absorb, and the warmer the Earth's surface will become. As a result, climate change can be caused by increases in greenhouse gases. As greenhouse gas levels rise, they absorb more of the outgoing radiation and the greenhouse effect becomes stronger. This causes the Earth's surface temperature to rise, leading to changes in the Earth's climate.

In summary, greenhouse gases are capable of absorbing infrared radiation, and as the concentration of greenhouse gases in the atmosphere increases, they become more effective at trapping heat and warming the Earth's surface, leading to changes in the Earth's climate.

To know more about greenhouse refer here:

https://brainly.com/question/1577730#

#SPJ11

The resistance of the load, given that 10.0 volts generate a current of 700 milliamps, is 14.3 ohms. To calculate this, you need to use Ohm's Law, which states that resistance (R) is equal to the voltage (V) divided by the current (I).

Therefore, R = V / I, or in this case, R = 10.0 volts / 0.700 amps = 14.3 ohms.

The resistance of the load can be calculated using Ohm's law, which states that the resistance is equal to the voltage divided by the current. In this case, the resistance would be 10.0V/0.7A, which equals 14.29Ω

The concept of resistance is important in audio signals and systems. As audio signals are AC, the resistance of a load determines how much of the signal is attenuated as it passes through the load. A higher resistance means that the signal is weakened, while a lower resistance means that the signal is stronger.

Therefore, knowing the resistance of a load is important when setting up audio systems, as it affects the strength of the signal that is sent to the speakers. Furthermore, impedance, which is closely related to resistance, is important in audio signals and systems, as it affects the quality of the signal being sent to the speakers.

For more questions related to Resistance.

https://brainly.com/question/29427458

#SPJ11

Grandma dynamite's bus has an acceleration of 7.5 m/s².

acceleration = (final velocity - initial velocity) / time

where the final velocity is 90 m/s, the initial velocity is 0 m/s (since the bus starts from a stop), and the time taken is 12 seconds.

acceleration = (90 m/s - 0 m/s) / 12 s

acceleration = 7.5 m/s²

Acceleration is a fundamental concept in physics that describes the rate of change of an object's velocity over time. It is defined as the change in velocity divided by the change in time, and is expressed in units of meters per second squared (m/s²).

Acceleration can occur in different ways, such as speeding up or slowing down, changing direction, or a combination of both. A positive acceleration means an object is speeding up, while a negative acceleration means it is slowing down. Acceleration also depends on the mass of the object, with a larger mass requiring a greater force to achieve the same acceleration as a smaller mass.

To learn more about Acceleration visit here:

brainly.com/question/30660316

#SPJ4

Option C, It would take 50 m³ of Mars' atmosphere to collect the same mass of air as one m³ on Earth. To calculate the volume of Mars' atmosphere required to collect a mass of 1kg, we need to use the density of the Martian atmosphere and the mass of the air on Earth.

The density of air at moderate altitude on Earth is given as 1 kg/m3. This means that 1 cubic meter of air on Earth has a mass of 1 kg. To convert this to grams per cubic centimeter, we can divide by 1000, which gives 0.001 g/cm3.

The mass of air in one m³ on Earth is 1 kg, while the density of the atmosphere near Mars' surface is 0.02 kg/m³. Therefore, to collect 1 kg of Mars' atmosphere, we need:

1 kg / 0.02 kg/m³ = 50 m³

So, it would take 50 m³ of Mars' atmosphere to collect the same mass of air as one m³ on Earth.

Complete question -

The density of air at moderate altitude on earth is 1 kg/m3 (this can be converted to 0.001 g/cm3). the density of the atmosphere near mars' surface is 0.02 kg/m3. how many m3 of mars atmosphere would it take to collect a mass of 1kg, the same mass as in one m3 on earth?

A. 1

B. 10

C. 50

D. 100

To know more about the density of air

brainly.com/question/30075980

#SPJ4

The total heat flux from the black body is 42643 W/m², due to radiation heat transfer, from a black body if the surface temperature is 600°C.

The heat flux due to radiation heat transfer from a black body can be calculated using the Stefan-Boltzmann law, which states that the heat flux is proportional to the fourth power of the temperature:

[tex]q(rad) = \sigma * \epsilon * A * T^4[/tex]

Where q(rad) is the heat flux (W/m²), σ is the Stefan-Boltzmann constant ([tex]5.67 * 10^{-8[/tex] W/m²K⁴), ε is the emissivity of the black body (assumed to be 1 for a perfect black body), A is the surface area of the black body, and T is the temperature in Kelvin.

To convert the temperature of 600°C to Kelvin, we add 273.15 K:

T = (600 + 273.15) K = 873.15 K

Assuming the black body has a unit surface area (A = 1 m²), the heat flux due to radiation can be calculated as:

[tex]q(rad) = \sigma * \epsilon * A * T^4 = 5.67 * 10^{-8} * 1 * 1 * (873.15)^4 = 14098[/tex] W/m²

The heat flux due to convection can be calculated using the following equation:

q(conv) = h * (T(surface) - T(air))

Where q(conv) is the heat flux (W/m²), h is the convection heat transfer coefficient (55 W/(m²°C)), T(surface) is the surface temperature (600°C), and T(air) is the air temperature (assumed to be 25°C).

To convert the surface temperature and air temperature to Kelvin, we add 273.15 K:

T(surface) = 600 + 273.15 = 873.15 K

T(air) = 25 + 273.15 = 298.15 K

Substituting the values, we get:

q(conv) = 55 * (873.15 - 298.15) = 28545 W/m²

Therefore, the total heat flux from the black body is:

q(total) = q(rad) + q(conv) = 14098 + 28545 = 42643 W/m²

learn more about heat flux

brainly.com/question/30708042

#SPJ4

Tension of approximately 2.7 x 10^20 N, will be observed in the cable.

If the Moon were held in its orbit by a long, mass-less cable attached to the center of the Earth, the tension in the cable would be equal to the force needed to keep the Moon in its circular path around the Earth. This force is the centripetal force, which is given by the equation,

Fc = mv^2/r

where Fc is the centripetal force, m is the mass of the Moon, v is the velocity of the Moon in its orbit, and r is the radius of the Moon's orbit.

The velocity of the Moon in its orbit can be calculated using the equation,

v = 2πr/T

where T is the period of the Moon's orbit.

Using the known values for the mass of the Moon, the radius of its orbit, and the period of its orbit, the tension in the cable can be calculated using the above equations. The result is a tension of approximately 2.7 x 10^20 N, which is an incredibly large force that is not physically possible to achieve with current technology.

To know more about Earth, here

brainly.com/question/20490748

#SPJ4

The diver's acceleration is 2.67 m/s^2.

We can use the formula for acceleration:

a = (vf - vi) / t

where a is acceleration, vf is final velocity, vi is initial velocity, and t is time.

In this problem, the initial velocity (vi) is 2 m/s downward, the final velocity (vf) is 6 m/s downward, and the time (t) is 1.5 seconds.

Plugging in these values, we get:

a = (6 m/s - 2 m/s) / 1.5 s

a = 4 m/s / 1.5 s

a = 2.67 m/s^2

As a result, the acceleration of the diver is 2.67 m/s^2.

Learn more about diver's acceleration at: https://brainly.com/question/25094023

#SPJ11

When the ball is in contact with the floor for 0.0300 seconds, the average force (in N) the floor exerts on the ball is 0 N. F = (Δp) / Δt

where Δp is the change in momentum of the ball and Δt is the time interval during which the change in momentum occurred.

Δp = mvf - mvi

where mvf is the final velocity of the ball and mvi is the initial velocity of the ball.

In this case, the ball is dropped from a certain height and comes to rest on the ground. This means that its initial velocity (mvi) is zero.

Hence:Δp = mvf - mvi

                 = mvf - 0

                 = mvf

The momentum is conserved in the vertical direction, which means that the final momentum (mvf) of the ball after bouncing is equal in magnitude but opposite in direction to its initial momentum.

Hence: mvf = - mvi

                   = - m * v0

where m is the mass of the ball and v0 is its initial velocity (which is zero).

Substituting the above expression for mvf into the equation for the average force:

F = (- m * v0) / Δt

where Δt = 0.0300 seconds is the time interval during which the change in momentum occurred.

F = (- m * v0) / Δt

  = (- 0.250 kg * 0) / 0.0300 seconds

  = 0 N

Therefore, the average force (in N) the floor exerts on the ball is 0 N.

To know more about momentum:

https://brainly.com/question/29598011

#SPJ11

The kinetic energy of the coffee filter is 0.63 x 10⁻³ J.

Kinetic energy is the energy possessed by a body by virtue of its motion, i.e. when the body is moving. So when the cofffee filter is dropped. it acquires kinetic energy because of its movement.

The kinetic energy of the coffee filter when it reaches the ground can be calculated using the equation:

K = (1/2) mv²

where m is the mass of the object and v is the velocity.

In this case, the mass of the coffee filter is 1.4 g and its velocity when it reaches the ground is 0.9 m/s.

Converting the mass into SI unit, we get mass = 1.4 x 10⁻³ kg

Therefore, the kinetic energy of the coffee filter is:

K = (1/2) x 1.4 x 10 ⁻³g x (0.9 m/s)² = 0.63 x 10⁻³ J

To summarize, the coffee filter of mass 1.4 g that is dropped from a height of 4m and reached the ground with a speed of 0.9 m/s² and has a kinetic energy of 0.63 x 10⁻³ J.

To know more about kinetic energy, refer here:

https://brainly.com/question/999862#

#SPJ4

The wavelength observed after Compton scattering for x-rays with an initial wavelength of 0.0679 nm is observed at a scattering angle of 140.0°.

Compton scattering is the interaction of a photon with an atomic electron that results in a decrease in the photon's energy and an increase in the scattered photon's wavelength.

The change in wavelength of the scattered photon can be calculated using the formula:

λ = λ0/(1 + (λ0/h)*(1-cosθ)), where λ0 is the initial wavelength, h is Planck's constant, and θ is the scattering angle.

Given initial wavelength λ0 = 0.0679 nm and Planck's constant h = 6.63*10^-34 J*s.

λ0 = 0.0679 nm = 6.79×10^-11 m

h = 6.63×10^-34 J·s

[tex]λ = λ0/(1 + (λ0/h)(1-cosθ))λ = 6.79×10^-11/(1 + (6.79×10^-11/6.63×10^-34)(1-cosθ))λ = λ06.79×10^-11/(1 + (6.79×10^-11/6.63×10^-34)*(1-cosθ)) = 6.79×10^-111 + (6.79×10^-11/6.63×10^-34)*(1-cosθ) = 1/(6.79×10^-11)cosθ = 1 - (1/(1 + (6.79×10^-11/6.63×10^-34)*(1/(6.79×10^-11))))cosθ = 0.252θ = cos^-1(0.252)θ = 140.0°[/tex]

Therefore, the wavelength observed after Compton scattering for x-rays with an initial wavelength of 0.0679 nm is observed at a scattering angle of 140.0°.

To know more about the scattering angle click here:

https://brainly.com/question/29806315

#SPJ11

The Blumlein technique should be avoided when using directional microphones due to probable phase cancellation problems caused by its bidirectional microphones.

Sound system amplifier methods are utilized to catch sound system sound in recording and broadcasting applications. While utilizing directional mouthpieces, like cardioid or supercardioid receivers, stage scratch-off issues can happen because of the directionality of the amplifiers.The Blumlein strategy, which utilizes two bidirectional receivers organized in an incidental pair, ought to be stayed away from while utilizing directional mouthpieces. This is on the grounds that the bidirectional mouthpieces utilized in the Blumlein strategy have invalid focuses at 90 degrees to the front and back of the receiver, which can prompt stage scratch-off when utilized related to directional amplifiers.All things being equal, sound system receiver strategies that utilization omnidirectional mouthpieces, like the separated pair method or the A-B strategy, are more reasonable for use with directional amplifiers.

To learn more about stereo microphone technique, refer:

https://brainly.com/question/12484674

The average force acting on the golf ball is 0.637 N.

To calculate the average force acting on the golf ball, we will use the equation

F = m*a

where F is the average force, m is the mass of the golf ball, and a is the acceleration.

To calculate the acceleration, we can use the equation

a = (vf - vi)/t

where vf is the final velocity, vi is the initial velocity (0 m/s in this case), and t is the time of contact. We know that the final velocity is 25.0 m/s, and the time of contact is 1.80 ms.

Therefore, we can calculate the acceleration to be

a = (25.0 m/s - 0 m/s) / 1.80 ms

a = 13.89 m/s².

Now that we have the mass and acceleration, we can calculate the average force. Using the equation F = m*a, the average force on the golf ball is

F = 0.0450 kg * 13.89 m/s² = 0.637 N.

Learn more about  force acting at https://brainly.com/question/29268524

#SPJ11

A guitar string oscillates with a frequency of 440 Hz and the air temperature is 20°C.

When a guitar string vibrates, it creates a sound wave. The sound wave that is produced by the guitar string is the sum of many individual waves that form the fundamental frequency and its harmonic overtones. The sound wave produced by the guitar string comprises areas of compression and rarefaction. Compression occurs when the air molecules are pressed together, whereas rarefaction occurs when the air molecules are pulled apart.

The wavelength of a sound wave can be calculated using the formula:

λ = v/f

where, λ = wavelength

v = velocity of sound in the medium

f = frequency of the sound wave

In this problem, the frequency of the sound wave is 440 Hz. At a temperature of 20°C, the velocity of sound in air is 343 m/s.

λ = 343 /440

λ = 0.78 m or 78 cm

Hence, the neighboring regions of compression in the sound wave that is created are 0.78 meters or 78 centimeters apart.   

Learn more about frequency

brainly.com/question/15853432

#SPJ11

Connecting an ammeter in series before or after a circuit component is the preferred method for measuring current because it allows for accurate readings, does not interfere with the circuit, and does not add any additional resistance to the circuit.

By connecting an ammeter in series, the current flows through it and the amount of current can be measured. This is due to the fact that when current is present in a circuit, it has to flow through every component of the circuit. By connecting the ammeter in series, the current will flow through the ammeter and the amount of current can be measured. Moreover, by connecting the ammeter in series, the amount of current through the circuit can be determined without disrupting the circuit or changing the current. This is because when an ammeter is connected in series, it does not interfere with the flow of current and does not add any resistance to the circuit. Furthermore, an ammeter connected in series allows for more accurate readings because the entire current is measured, not just a fraction of it.

For more questions related to ammeter.

https://brainly.com/question/30849022

#SPJ11