There are lots of hazard. The type of hazard that the operator will be exposed to is noise.
What is noise hazard?Noise is known to be a very popular form of physical hazards that is said to be present in all occupation.
This noise hazard is often based on its frequency, amplitude (volume) and term of exposure such as long or short term, It is said that one should wear hearing protection as long exposure to noise can lead to temporary or permanent loss of hearing.
Learn more about operator from
https://brainly.com/question/17484823
What action control to move the rudder from one point to the other?
The action control to move the rudder from one point to the other is doen when The rudder, when turned to starboard, produce a force that is towards the port (called the rudder force).
What controls the rudder of a ship?In a vessel or ship, found in small craft, the rudder is known to be operated manually through the use of a handle that is called a tiller or helm.
In a bigger vessels, the rudder is known to be turned through the use of an hydraulic, steam, or electrical machinery. The first type of rudder was side to be a paddle or oar.
Learn more about action from
https://brainly.com/question/1718605
List principles that are most relevant to drop jump exercise and justify your answers that selected principles you
are chosen are most relevant?
The principles referred to in the question are called biomechanical principles. Some of them are:
Principles of Force; andThe principle of impulse direction.
The principle that is most relevant to jumping is called Angular Momentum.
What is Angular Momentum?
Simply defined, this refers to the velocity of the rotation of a body around an axis or a fixed point.
Other principles of biomechanics are the principles of:
See more about biomechanical principles at:
https://brainly.com/question/1087668
Calculate LER for the same wing if we increase the span to 0.245 m. By increasing the span, we also increase the glider weight to 0.0523 newtons.
4.74
0.2108
0.0523
0.18
Answer:
0.2108
Explanation:
WA = 0.245 x 0.045 = 0.011025 m2. Then, LER = 0.011025/0.0523 = 0.2108.
An amount P is deposited now so that an equal annual amount of A1=2000 per year for the first 5 years, starting 1year after the deposit. And a different annual withdrawal of A2= 3000 per year for the following 3 years. Draw the cash flow diagram if i=8.5% per year.
Based on the amounts to be withdrawn over the years and the interest rate, the amount deposited now is $12,977.
How much is deposited now?This can be found as:
= (2,000 x Present value of annuity interest factor, 8.5%, 5 years) + (3,000 x Present value of annuity interest factor, 8.5%, 8 years) - (P/A, 8.5%, 5 years)
= (2,000 x 3.9406) + (3,000 x (5.6392 - 3.94064))
= $12,977
The cashflow diagram is attached.
Find out more on cashflow diagrams at https://brainly.com/question/23841852.
eering job role to its description.
project engineer
planning engineer
chief engineer
field engineer
office engineer
heads the engineering department and
ensures that it operates smoothly
performs administrative work to ensure
projects comply with engineering codes
and standards
I rights reserved
Answer:
Dear if possible can you post the complete question
I would be grateful to help you
What math subjects are going to be seen in Industrial Engineering?
Answer:
Industrial Engineers study various types of math including calculus, numerical analysis, statistics, linear algebra, numerical methods, operations research, etc. We do not necessarily use these in our day-to-day activities, but they help to build an analytical mindset that many employers value.
You are surely going to have commercial subjects , honestly when doing engineering every type of math is taught.
marks)
Question 2
Distinguish between the following pairs of terms:
i. Quadrant bearing and Azimuth
5
ii. Constant error and Human error
5
iii. Referencing and Detailing
E
iv.
Accuracy and Precision
V. Bar scale and Representative fraction scale
Answer:
referencing and detailing
A 750-m section of river runs parallel to a channel 1,000 m away. an aquifer connecting the two has hydraulic conductivity equal to 7. 0 m/day and an average thickness of 10 m. the surface of the river is 5. 0 m higher than the surface of the channel. estimate the rate of seepage (qseepage) from the river to the channel
Given a 750 m section with distance of 1000m , The calculated rate of seepage from the river to the channel has been calculated to be 262.5 m³/day.
What is the rate of seepage?
This is the calculated rate that shows how water is infiltrated downward into the soil.
The formula is given as
[tex]Q = KA \frac{dh}{dl}[/tex]
A = Area = 750*10 = 7500m
dh = h₂-h₁
= 10 - 5 = 5m
dl = 1000m
[tex]Q = 7*7500*\frac{5}{1000}[/tex]
= 262.5m³
The rate of seepage from the calculation above is 262.5m³.
Read more on rate of seepage: https://brainly.com/question/21499824
Along with refining craft skills another way to increase the odds for career advancement is to
A. Get additional certifications
B. Work for multiple contractors
C. Become friends with management
D. Get more expertise from the Internet
The acquisition of additional certifications with a personal refined craft skills can increase the odds for career advancemen.
What is a career advancement?An advancement is achieved in a career if a professional use their skill sets, determination or perserverance to achieve new career height.
An example of a career advancement is when an employee progresses from entry-level position to management and transits from an occupation to another.
Therefore, the Option A is correct.
Read more about career advancement
brainly.com/question/7053706
An iron–constantan thermocouple is to be used to measure temperatures between 0 and 400°C. What will be the non-linearity error as a percentage of the full-scale reading at 100°C if a linear relationship is assumed between e.m.f. and temperature? e.m.f. at 100°C = 5.268 mV, e.m.f. at 400°C = 21.846 mV
Answer:
-0.89%
Explanation:
Assuming a proportional relationship between EMF and Celsius temperature, the measured value of EMF at 100 °C will be interpreted as a temperature of ...
T/5.268 = 400/21.846
T = 5.268(400/21.846) ≈ 96.457 . . . . °C
The error as a fraction of full scale is ...
(96.457 -100)/400 × 100% ≈ -0.886%
The error at 100 °C is about -0.89% of full scale.
52 M ta 10 2-22 2-а. for C calculate the current passing through the 4ohm resistor using thevenin's theorem.
Explanation:
a stationer sell 8 pencil for the cost price of 10 ,find his gain percent
A gaseous mixture contain 32.9 mol % He, 40.7 mol % N_{2} and 26.4 mol % Ar. Determine the composition of this mixture on a mass basis based on the molecular weight given: MW(He) = 4.003 , MW (N_{2}) = 28.02 MW(Ar) = 39.95
The composition of the mixture on a mass basis are as follows:
He = 131.70 gN2 = 1140.41 gAr = 1054.68 gnumber of moles = mass of substnce / molar mass
molar mass and molecular weight has equal numerical values therefore
Number of moles = mass of substnce / molecular weight
mass of substance = number of moles * molecular weight
the moles are expressed in percentage hence the total moles should be 100
check: 32.9 + 40.7 + 26.4 = 100
He
mass of substance = 32.9 * 4.003 = 131.6987 g
[tex]N_{2}[/tex]
mass of substance = 40.7 * 28.02 = 1140.414 g
Ar
mass of substance = 26.4 * 39.95 = 1054.68 g
Which of these items is least likely to cause an exhaust emission test failure as of a result of excessive nox emissions? a) poorflow through the egr system. b) spark plug hot range. c) defective fuel injector d) defective oxygen senor
The item that is least likely to cause an exhaust emission test failure as of a result of excessive nox emissions is; poorflow through the egr system.
What is an exhaust emission?Exhaust emissions simply means substances emitted into the atmosphere from the exhaust discharge nozzle of an aircraft or aircraft engine.
Now, when the test fails as a result of excessive nox emissions, we can say that high NOx emissions can occur when an engine's air-fuel mixture is too lean. Thus, we can conclude that the reason for exhaust emission test failure as of a result of excessive nox emissions is due to poorflow through the egr system.
Read more about emissions at; https://brainly.com/question/14154063
Technician A says that a range shift is used to select high or low gear ratios within the transfer case. Technician B says that a mode shift is used to select two wheel drive or four wheel drive. Which technician is correct
Technician A says that a range shift is used to select high or low gear ratios within the transfer case is true while Technician B is false.
What is this shift about?A range shift is known to often take place when there is either high or low speed ratio of the given transfer case that is known to be selected.
Note that A range shift arrangement is known to be seen for moving a gear reduction unit that is found between a low-range operating speed and also that of a high-range operating speed.
Learn more about Technician from
https://brainly.com/question/2328085
#SPJ1
A company intends to market a new product and it estimates that there is a 20% chance that it will be first in the market
and this will give 2 million dollar revenue in its first year. However, if it is not the first in the market it will only be .5 million.
What is the EMV?
The EMV - Ending Market Value is given as:
$2,400,000.
The EMV is given as:
BMV x (i + r); Where
BMV is the Beginning Market Value; and
r is the interest rateor percentage given.
Hence the EMV = 2,000,000 x ( 1 + 20%)
= 2,000,000 x 1.2
= $ 2, 400,000.
It is to be noted that the BMV is the Beginning Market Value which is the value of an investment at the start of the business period.
Learn more about Market Value at:
https://brainly.com/question/1350233
An evacuated tank is filled with gas from a constant pressure line. Develop an expression relating the temperature of the gas in the tank to the temperature of the gas in the line. Assume the gas is ideal with constant heat capacities, and ignore heat transfer between the gas and the tank.
The temperature of the gas in the tank is the ratio of heat capacities times the temperature of gas in the constant pressure line.
What is temperature?It should be noted that temperature simply means the measure of hotness and coldness in a body
From the given information, H is the enthalpy of gas on the constant pressure line, m is the mass flow rate and U is the internal energy of gas.
Here, the temperature of the gas in the tank is the ratio of heat capacities times the temperature of gas in the constant pressure line.
Learn more about temperature on:
https://brainly.com/question/24746268
How deep is a 6ft hole?
Answer:
I know this sounds quite deep but it is as deep as a grave
Explanation:
It's reality
Answer:
6ft or 72 inches
Explanation:
The hole is most likely 6ft or also known as 72 inches.
Hope this helps :-)
Have a great rest of your day or night!
<3 simplysun
A legal document that traces the ownership of a piece of property
Answer:
A title
Explanation:
A title is a legal document that proves legal ownership over an asset or piece of property. Assets such as homes, land, other types of real estate, vehicles, and personal property such as jewelry all have titles to demonstrate ownership.
What do we mean by “whiteness” and how does that
determine/influence our society?
Answer:
whiteness refers to white people(WHITE americans), back then white people got all the good stuff while colored people (meaning everyone who is not white) got old breaking down things. This influenced our society back then and made people think that white people are way better than colored. Which is SO NOT true, everyone is the same
What is txv to hvac parts and etc???
Answer:
This is for all hvac parts lol
Answer:
Units larger than a terabyte include a petabyte, exabyte, zettabyte, yottabyte and brontob
What are the colors of a sign which tells you the distance to the next exit of a highway?.
Green with white lettering are the colours of a sign which tells you the distance to the next exit of a highway.
What are the colour signs of distance?Green is a common color for directional signage. Along with location and directions, these signs also tell you how far something is. Blue: This color is also used for wayfinding signage. Information on nearby amenities including rest areas, hospitals, gas stations, and motels is provided by these signs.
Red could be difficult to understand in a crisis because we are taught to interpret it as "stop." Contrarily, green signifies safety and "go," making it clear to the public to maintain composure and abide by the denotations. This is why green emergency signs are utilized in public buildings.
White: A white backdrop indicates a regulatory sign. Yellow: A general warning is sent by the color yellow. Green: Green denotes safe directing indicators or traffic patterns.
Thus, Green with white lettering.
For more information about colour signs of distance, click here:
https://brainly.com/question/14453702
#SPJ6
Joe is a chemical engineer whose plant discharges heavy metals into the local river. By the test authorized by the city government, the amount of heavy metals is under the legal limit imposed by the city. By a new and more accurate test, the discharge is above the legal limit, that is, the discharge is in violation of environmental rules. Joe argues with his manager that the plant should reduce its discharges to comply with the newer and more accurate test.
The case contains a conceptual issue insofar as:
A.the issue is whether present emission rates constitute a violation of city regulations.
B.the issue is what is meant by “violation.”
C.the issue is how Joe should balance his obligations to his employer against his obligations to city residents.
D.the issue is whether the heavy metals presently emitted by the plant pose a threat to the health of the community.
Answer:
B probably
Explanation:
Because the prompt doesn't specify what sort of violation it could be anything maybe when they release the metals during the day and so on.
technician A says that many port fuel-injection systems on four-cylinder engines use a simultaneous firing of injectors. Technician B says that sequential fuel injectors are timed and pulsed individually, much like the spark plugs are sequentially operated in firing order of the engine. Who is correct
In the two scenario above concerning port fuel-injection and sequential fuel injectors, only Technician b is correct.
How many injectors can be found in a 4 cylinder?A vehicle often has one fuel injector per cylinder and if one has a four-cylinder car, it would also have four fuel injectors.
Note that Fuel-pressure regulators that are found on a port fuel-injected systems is one that often work with injector pressures that is said to be of 30 to 55 PSI.
Learn more about Technician from
https://brainly.com/question/5122191
There are withdrawn 100 ft3
of air measured at 30 psia and 90°F from a 50 ft3
tank containing air
initially at 100 psia and 140°F. What is the pressure of the air remaining in the tank if its
temperature is 130 °F?
Answer:
2+2g
what time is good afternoon my
A farmer has 12 hectares of land on which he grows corn, wheat, and soybeans. It costs $4500 per hectare to grow corn, $6000 to grow wheat, and $5000 to grow soybeans. Because of market demand the farmer will grow twice as many hectares of wheat as corn. He has allocated $6,375,000.00 for the cost of growing his crops. How many hectares of each crop should he plant?
The number of hectares of each crop he should plant are; 250 hectares of Corn, 500 hectares of Wheat and 450 hectares of soybeans
How to solve algebra word problem?
He grows corn, wheat and soya beans on the farm of 1200 hectares. Thus;
C + W + S = 12 ----(1)
It costs $45 per hectare to grow corn, $60 to grow wheat, and $50 to grow soybeans. Thus;
45C + 60W + 50S = 63750 -----(2)
He will grow twice as many hectares of wheat as corn. Thus;
W = 2C ------(3)
Put 2C for W in eq 1 and eq 2 to get;
C + 2C + S = 1200
3C + S = 1200 -----(4)
45C + 60(2C) + 50S = 63750
45C + 120C + 50S = 63750
165C + 50S = 63750 ------(5)
Solving eq 4 and 5 simultaneosly gives;
C = 250 and W = 500
Thus; S = 1200 - 3(250)
S = 450
Read more about algebra word problems at; https://brainly.com/question/13818690
What should you do when operating in conditions of reduced visibility.
Answer:
You shold wear Gogles
Explanation:
It is harder to see with no gogles
When operating in low-visibility situations, it is critical to take necessary precautions to preserve safety and retain situational awareness. When operating in low-visibility situations, it is critical to take necessary precautions to preserve safety and retain situational awareness.
Slow down: Reduce your speed to compensate for decreased vision. This provides you with additional time to respond to unanticipated obstructions or threats. Increase your following distance by leaving a bigger gap between your car and the vehicle ahead of you. This acts as a buffer zone and allows for more stopping distance.
Turn on your headlights and fog lights, even during the day, to improve visibility for yourself and other vehicles. Use fog lights if your car has them, as they are meant to penetrate fog and provide improved illumination. Use windscreen wipers and defrosters: Make sure your windscreen wipers are in good working order and that the appropriate speed setting is used to keep the windscreen clear. To prevent window fogging, turn on the defroster if necessary.
To know more about visibility, here:
https://brainly.com/question/33339568
#SPJ4
Which of the following materials are examples of ceramics?
A
fiberglass, carbon fiber, and Kevlar
B
cedar, mahogany, and bamboo
C
brick, glass, and porcelain
D
nylon, leather, and asbestos
Answer:
c
Explanation:
A are types of fiberous materials
B is woods
c ceramics
D unrelated materials
Assume you have four fins, each with a mass of 8. 0 grams. What is the total weight of these four fins? (Hint: watch your units!) PLEASE HELP ASAP! I have a 0% in this class
Answer:
0.314 kg
Explanation:
[tex]\frac{8}{1000}[/tex] x 4 x 9.81
Answer:
.3139 joules
Explanation:
Weight in the metric system is ma
you have 4 fins that have MASS of 8 grams each
or 32 grams which is .032 kg
WEIGHT would be .032 kg * 9.81 m/s^2 = .31392 j
5. Tech A says that shock absorbers can be tested with a "bounce test." Tech says than
is industry standard to replace an individual faulty shock absorber. Who is correct?
d. Tech A
b. Tech 8
8. Both A and B
d. Neither Anor B
Answer:
I know A is correct but not so sure about B, like I don't know if B is correct or wrong
What does hydraulic force provide in a braking system?
Power
Heat dissipation
Contact surface
Pressure
Answer:
4 or D pressure
Explanation:
A hydraulic braking system transmits brake-pedal force to the wheel brakes through pressurized fluid, converting the fluid pressure into useful work of braking at the wheels.
Answer:
pressure is the correct answer...
Explanation:
mark me brainliest