Which statement best describes the most likely temperatures of Portland, Oregon, and Eugene, Oregon, on this day in January?
А
Eugene was a little colder than Portland because Eugene is a little closer to the coast.
B
Portland was a little colder than Eugene because Portland is a little farther to the north.
С
Portland was much colder than Eugene because Portland was north of the polar jet stream.
a
D
Eugene was much colder than Portland because Eugene was south of the polar jet stream.

Answer:

You dial a number on your phone

Your phone contacts a base station

The base station contacts the MTSO

The MTSO connects you to the other device

You talk to the person on the other device.

Answer:

64.6% of Br and 35.4% of Sr

Explanation:

The percentage composition is obtained defining the percentage in mass of each atom in a molecule.

To solve this question we must find the mass of each atom in 1 mole:

Molar mass Br: 79.904g/mol

Molar mass Sr: 87.62g/mol

The molar mass of SrBr2 is:

79.904g/mol*2 + 87.62g/mol =

159.808g/mol + 87.62g/mol =

247.428g/mol

The percentage of Br is:

79.904g/mol*2 = 159.808g/mol / 247.428g/mol * 100

= 64.6% of Br

And percentage of Sr is:

87.62g/mol / 247.428g/mol * 100

= 35.4% of Sr

Answer:

Explanation:

Radon is radioactive.

Radon is a naturally occurring radioactive gas.  

Radon causes cancer.

Breathing radon can increase your risk of developing lung cancer.  

No immediate symptoms.  

You must test for radon.  

Radon is present indoors and outdoors.  

Radon can build up in any building.

Answer: No but I have a three elmos dolls in my basement

Explanation:

Answer: [tex]3.903\times 10^{23}[/tex]

Explanation:

Given

Mass of magnesium is [tex]m=15.75\ gm[/tex]

The molar mass of magnesium [tex]M=24.3\ g/mol[/tex]

No of moles in 15.75 g of magnesium is

[tex]\Rightarrow n=\dfrac{15.75}{24.3}\\\\\Rightarrow n=0.648\ \text{moles}[/tex]

1 mole contains [tex]6.022\times 10^{23}[/tex] atoms

So, 0.648 moles contain [tex]0.648\times 6.022\times 10^{23}[/tex]

[tex]=3.903\times 10^{23}\ \text{atoms}[/tex]

Answer:

pag pinag balik tad moyan tama magiging tama sagot nya promise jslsh

Answer:

The pH of a solution with a Hydronium (H₃O⁺) ion concentration of 0.001 M is 3.

Explanation:

pH, short for Hydrogen Potential, is a measure used to establish the level of acidity or alkalinity of a solution.

pH indicates the amount of hydrogen ions present in a solution or substance. Mathematically the pH is the negative logarithm of the molar concentration of hydrogen ions or protons (H⁺) or hydronium ions (H₃O⁺).

pH= - log [H⁺]= - log [H₃O⁺]

The pH scale goes from 0 to 14. Values ​​less than 7 indicate the range of acidity and those greater than 7 indicate alkalinity or basicity. The value 7 is considered neutral.

In this case, [H₃O⁺]= 0.001 M.

Replacing in the definition of pH:

pH= - log (0.001 M)

Solving:

pH= 3

The pH of a solution with a Hydronium (H₃O⁺) ion concentration of 0.001 M is 3.

Respuesta:

1.50 moles

Explicación:

Paso 1: Escribir la ecuación química ajustada para la descomposición del carbonato de calcio

CaCO₃ ⇒ CaO + CO₂

Paso 2: Calcular los moles correspondientes a 150 g de CaCO₃

La masa molar de CaCO₃ es 100.09 g/mol.

150 g × 1 mol/100.09 g = 1.50 mol

Paso 3: Calcular los moles de CO₂ producidos a partir de 1.50 moles de CaCO₃

La relación molar de CaCO₃ a CO₂ es 1:1.

1.50 mol CaCO₃ × 1 mol CO₂/1 mol CaCO₃ = 1.50 mol CO₂

Answer:

Zinc blend is Zinc sulphide, ZnS.

ZnS is roasted in air producing ZnO and Sulphur dioxide.

ZnO is reduced to Zn by CO.

Further purification is done by electrolysis.

Answer:

c

Explanation:

boiling

Answer:

-what color is the tube: Transparent

-is the reaction reversible: what reaction

-has the reaction reached equilibrium: I don't see a reaction

BTW you didn't provide all the information.

Answer:

A metallic bond is a force of attraction between charged metal ions and the electrons that are in the delocalized bond, which covers the assembly of ions. A covalent bond is the force of attraction between the nuclei of atoms, and the electrons shared between them.

Explanation:

A chemical bond is a lasting attraction between atoms, ions or molecules that enables the formation of chemical compounds. The bond can be generated by electrostatic attraction between charged ions (for example, ionic bonds) or by electron sharing (for example, covalent bonds).

I hope this helps you :)

Answer: B

your welcome Bsbssnsnsmsllqql

Answer:

P1 =4 atm

T1= 20°C

P2=1 atm

T2=?

According to Gay-Lussac's Law or Third Gas Law,

P1T2=P2T1

4×T2=1×20

T2= 20/4

T2= 5°C

Answer At 5°C temperature does a gas at 1.00 atm !

Answer:

Distance

Explanation:

now that i do and I also believe adopt don't shop and also no puppy mill.

Answer:

option d) is the correct answer

Answer: OCl2 is polar because the two O-Cl bond dipoles don't cancel each other.

Answer:

mass = 102.69 g of sucrose

Explanation:

First, you need to use the correct expression of molality (m) which is the following:

m = moles / kg solvent    (1)

According to the exercise, we need to get the grams, in other words, the mass of the sucrose. To get the mass, we need the moles and molecular weight of sucrose and use the following expression:

moles = mass / MM    (2)

Now, if we replace (2) in (1) we have:

m = mass / MM * kg solvent   (3)

From here, we solve for the mass and then:

mass = m * MM * kg solvent (4)

Now, then density of water is 1 kg/L, so, the volume of the water will be the same as it's mass, and the molality is 3 m. The molecular weight of the sucrose is (according to several sources) 342.3 g/mol. Replacing all the data in (4) we have:

mass = 3 mol/kg * 0.1 kg * 342.3 g/mol

Hope this helps

Answer:

c. floodplain

Explanation:

brainliest please!

Answer:

I think the answer is floodplain.

Explanation:

I hope this helps, have a blessed day.

Answer:

gas

Explanation:

particles are very far apart

The given diagram represents gaseous state of matter.  Both a volume and a definite form are absent from a gas. The separation of gas particles is great.

Solids, liquids, gases, plus plasma are the four states of matter that may be found in daily life. However, a number of additional states of matter have indeed been found.

Some of these additional states are created when a material transitions among two states of matter and doesn't actually exhibit the characteristics of either state. The most exotic are others. Both a volume and a definite form are absent from a gas. The separation of gas particles is great. The gas in a balloon and the air are two examples of gases. The given diagram represents gaseous state of matter.

Therefore, the given diagram represents gaseous state of matter.

To learn more about state of matter, here:

https://brainly.com/question/9402776

#SPJ6

Answer:

La cantidad de energía disponible de una fuente de energía determinada se denomina recurso energético. La escasez de recursos energéticos (petróleo, carbón y madera) en algunas de las fuentes de energía más utilizadas plantear necesidad de usar otras fuentes investigar el modo más rentable de emplearlas

Explanation:

Answer:

false

Explanation:

its the amount of high-quality energy available from a given quantity of an energy resource minus the high-quality energy needed to make the energy available.

Answer:

Please find the explanation to this question below.

Explanation:

Answer:

97.7 kJ

Explanation:

We'll use the formula for specifc heat: Q=mcΔT

Q= heat/energy (Joules), m= mass (grams), c= specific heat (different for each substance and is usually given)

ΔT= final temperature - initial temperature

Let's check our given units and see if they're the correct, here they all are. Let's plug in what we know.

Q=mcΔT

Q=(480)(0.96)(234 - 22)

Q=(480)(0.96)(212)

Q= 97,690 J

Before we submit an answer, let's check out units. We have our answer in Joules, but we want it it kilojoules, so we'll convert it knowing that:

1000 Joules = 1 kilojoule

97,690J x [tex]\frac{1 kJ}{1000J}[/tex] = 97.7kJ

Explanation:

the answer and the working out is shown above.

Answer:

As nouns the difference between impression and imprint

is that impression is the indentation or depression made by the pressure of one object on or into another while imprint is an impression; the mark left behind by printing something.

The term imprint is defined as to mark by or as if by pressure and the term impression is defined as the effect produced by impressing.

The difference between an imprint and an impression is that the imprint is the mark left behind when anything is printed, whereas the impression is the indentation or depression caused by the pressure of one object against or into another.

While a shoe won't make an impression in loose sand, it will on a hard surface like concrete or linoleum. These imprints or impressions might be contrasted with the shoe of a suspect or the tire of a car to see if they belong to the same object.

Thus, The term imprint is defined as to mark by or as if by pressure and the term impression is defined as the effect produced by impressing.

To learn more about the imprint and the impression, follow the link;

https://brainly.com/question/20410964

#SPJ2

Answer:

Landslides, Volcanoes, Earthquakes, and Floods. A opening in the Earth's surface through which melted rock, gases, and ash escape. Events in which molten rock spews out from the mantle to the surface of Earth as ash, lava, and gases

Explanation:

Explanation:

If the density of the object is more than that of water, it will sink. Otherwise it will float. The density of water is 1 g/mL.

Substance 1,

Mass, m = 450 g, Volume, V = 90 mL

Density = mass/volume

So,

[tex]d_1=\dfrac{450}{90}\\\\=5\ g/mL[/tex]

It will sink.

Substance 2,

Mass, m = 35 g, Volume, V = 70 mL

Density = mass/volume

So,

[tex]d_2=\dfrac{35}{70}\\\\=0.5\ g/mL[/tex]

It will float.

Substance 3,

Mass, m = 24 g, Volume, V = 12 mL

Density = mass/volume

So,

[tex]d_3=\dfrac{24}{12}\\\\=2\ g/mL[/tex]

It will sink.