could any of you please help i really need it

The voltage of the battery would be 20 volts. Option I.

According to Ohm's law, the voltage (V) across a resistor is equal to the current (I) flowing through it multiplied by its resistance (R). Mathematically,

V = I × R

In this case, the current (I) flowing through the resistor is given as 10 A and the resistance (R) of the resistor is given as 2 ohms. Substituting these values into the above formula, we get:

V = 10 A × 2 ohms = 20 volts

Therefore, the voltage of the battery is 20 volts.

More on voltage can be found here: https://brainly.com/question/13521443

#SPJ1

Answer:

The student used 24000 Joules of energy.

Explanation:

We can use the Energy Power equation to solve this example.

[tex]\sf E=Pt[/tex]

Where

[tex]\sf E[/tex] is the energy in Joules (J)

[tex]\sf P[/tex] is the power in Watts (W)

[tex]\sf t[/tex] is the time in seconds (s)

Numerical Evaluation

In this example we are given

[tex]\sf P=800\\t=30[/tex]

Substituting our given values into the equation yields

[tex]\sf E=800 \cdot 30[/tex]

[tex]\sf E=24000[/tex]

24000 Joules  

[tex]\Large\bold{SOLUTION}[/tex]

To calculate the energy used by the student in this scenario, we can use the formula:

[tex]\sf{Energy\: (in\: Joules) = Power\: (in\: Watts) \times Time\: (in\: seconds)}[/tex]

Given that the student uses an 800 W microwave for 30 seconds, we can plug in these values to the formula:

[tex]\sf Energy = 800\: W \times 30\: s = 24,000\: J[/tex]

Therefore, the student uses 24,000 Joules of energy in this scenario.

[tex]\rule{200pt}{5pt}[/tex]

Answer:

Explanation:

We can solve this problem using kinematic equations. We know that the initial velocity of the ball is 55 m/s at an angle of 30° to the horizontal. We can break this velocity into its horizontal and vertical components:

vx = v0 cos θ = 55 cos 30° = 47.6 m/s

vy = v0 sin θ = 55 sin 30° = 27.5 m/s

We can now use the vertical motion equation to find the time it takes for the ball to reach its maximum height:

Δy = vy t + 0.5 a t^2

At the maximum height, the vertical velocity of the ball is 0, so we have:

0 = vy + a t_max

Solving for t_max, we get:

t_max = -vy / a = -27.5 / (-9.8) = 2.81 s

The ball will take twice this time to reach the fence, since it needs to come back down to the ground:

t_total = 2 t_max = 5.62 s

The horizontal distance the ball travels during this time is:

Δx = vx t_total = 47.6 × 5.62 = 267.7 m

Since this distance is greater than the distance to the fence (120 m), the ball will reach the fence if it leaves the bat traveling upward at an angle of 30° to the horizontal.

Answer:

It depends on how they are made.

Explanation:

Rubber balloons are not always spherical in shape. When filled with air, the inflation forms a balance between the balloon material, including its shape and thickness and its elasticity and the pressure of the air. That’s what determines its shape. Although a sphere is often the shape, it could be tubular, offset, and most other shapes.

Real, inverted, and same size are the features of the image. when A concave mirror with a curvature of 8 is displayed on a ruler with a range of 0 to 14 cm.

The mirror formula may be used to calculate the image distance for an item located 4 cm from a 1.5 cm focal length mirror.

1/f = 1/u+1/v

f is the focal length

u is the object distance

v is the image distance

Keep in mind that the concave mirror's image distance and focal length are both positive.

Given:

u = 4cm

f = 1.5cm

1/v = 1/1.5-1/4

1/v = 0.67-0.25

1/v = 0.42

v = 1/0.42

v = 2.38cm

The picture is Genuine and INVERTED since the image distance value is positive.

We shall find its magnification and see if it is magnified or lessened. It is amplified if the magnification is larger than 1, and it is decreased if it is less.

Magnification = v/u

Magnification = 2.38/4

Magnification = 0.595 or. 0.6

The picture is reduced in size since the magnification is less than one (SMALLER).

Learn more about Inverted here:

https://brainly.com/question/16150120

#SPJ1

Answer:

15 hours

Explanation:

formula: f(a) = a(0.5)^(T/t)

fill in known values: 13=208(0.5)^(60/t)

use natural log to isolate t:    ln(13/208)=ln(0.5)(60/t)

solve for t: t=15

Mechanical energy to heat energy is collision,force x distance is work done,rubbing energy friction, stewardship is using energy wisely and nuclear energy can cause heat pollution.

For more information on energy kindly visit to

https://brainly.com/question/10770247

#SPJ1

Her average speed was about 4.6 km/hr, and her average velocity was about 3.3 km/hr.

The entire distance travelled divided by the total time taken is the definition of average speed. In this case, the total distance travelled was 7.0 km, and the total time taken was 1.5 hours. Hence, the average speed can be determined as follows:

Average Speed = [tex]\frac{7.0 km }{ 1.5 \ hours }= 4.6 km/hr[/tex]

The displacement divided by the whole time travelled is the average velocity. In this case, the displacement was 3.0 km (from Mary's home to Sheila's home), and the total time taken was 1.5 hours.The average velocity can therefore be determined as follows:

Average Velocity = [tex]\frac{3.0 km }{1.5 \ hours} = 3.3 km/hr[/tex]

Therefore,Her average velocity was roughly 3.3 km/hr, and her average speed was roughly 4.6 km/hr.

learn more about Average speed Refer:brainly.com/question/12322912

#SPJ1

Explanation:

Inertia refers to the tendency of an object to resist changes in its motion. In baseball terms, a baseball that is at rest on the ground has a high level of inertia because it is resistant to moving until an external force, such as a player's bat, acts on it.

Momentum, on the other hand, is the product of an object's mass and velocity and refers to the quantity of motion that an object possesses. In baseball terms, a baseball that is moving at a high velocity, such as when it is hit by a bat, has a high level of momentum.

To illustrate the difference between inertia and momentum in baseball, consider the scenario of a baseball that is hit by a bat. Before the bat hits the ball, the ball is at rest and has a high level of inertia. However, once the bat hits the ball, the ball gains momentum and begins to move. As the ball moves, it continues to possess momentum, but its inertia gradually decreases as it encounters external forces, such as air resistance and friction from the ground, which act to slow it down.

Answer:

0.625 meters

Explanation:

We can use the work-energy that the work done on an object is equal to the change in its kinetic energy:

Work = ΔK = Kf - Ki

Where:

Work is the work done on the object

ΔK is the change in kinetic energy of the object

Kf is the final kinetic energy of the object

Ki is the initial kinetic energy of the object (which is zero since the object is at rest)

The work done on the object is equal to the force applied to the object multiplied by the distance over which the force is applied:

Work = F × d

Where:

F is the force applied to the object (50 N)

d is the distance over which the force is applied (unknown)

So we can write:

F × d = Kf - Ki

Substituting the given values:

50 N × d = 1/2 × 10 kg × (2.5 m/s)^2 - 0

Simplifying:

50 N × d = 31.25 J

Solving for d:

d = 31.25 J / 50 N = 0.625 m

Therefore, the object was moved a distance of 0.625 meters.

please rate

Plugging in the values of the length and diameter, along with the error value, the error in the volume of the cylinder is approximately 1.27 cm³.

Error in measurement refers to the deviation or difference between the true or expected value and the measured value of a physical quantity. The presence of errors in measurement can affect the accuracy and precision of the results obtained.

To compute the possible error in the volume of the cylinder, we first need to calculate the volume of the cylinder using the measured values of its length and diameter:

V = πr²h

r = d/2 = 2.1/2 = 1.05 cm

V = π(1.05)²(8.9) = 31.79 cm³

Now, we need to determine the possible error in the volume, which can be calculated using the formula:

ΔV = V × √[(Δd/d)² + (Δh/h)²]

where Δd and Δh are the uncertainties in the diameter and length measurements, respectively. Substituting the given values, we get:

ΔV = 31.79 × √[(0.1/2.1)² + (0.1/8.9)²] = 1.27 cm³ (approx.)

Therefore, the possible error in the volume of the cylinder is approximately 1.27 cm³.

To find out more about errors, visit:

https://brainly.com/question/28109798

#SPJ1

The secondary coil needs 120 turns.The power transmitted to the secondary winding is 0.155 W.

A transformer works by using electromagnetic induction to transfer electrical energy between two circuits. The voltage changes between the primary and secondary coil based on the ratio of the number of turns in each coil. In a step-up transformer, the voltage is increased from the primary to the secondary coil, while in a step-down transformer, the voltage is decreased.

Transformers are commonly used in electronic devices to convert voltage levels, isolate circuits, and match impedances. They are often used in power supplies to step down the voltage from the wall outlet to a level that can be used by the device. They are also used in audio amplifiers to match the impedance of the output to the speaker, and in radio and television receivers to tune in to different frequencies.

To know more about voltage,visit:

https://brainly.com/question/29445057

#SPJ1

Answer:

Explanation:

The time taken to travel from Fort Worth to Dallas is:

t = 3:23 pm - 2:41 pm = 42 minutes = 0.7 hours

The distance covered is:

d = 58 km

The average speed is:

v = d/t = 58 km / 0.7 hours = 82.86 km/h

To convert km/h to m/s, we can use the conversion factor:

1 km/h = 0.2778 m/s

Therefore, the average speed in m/s is:

v = 82.86 km/h × 0.2778 m/s/km = 23.06 m/s (rounded to two decimal places)

So the average speed is 23.06 m/s.

If F₁ has a greater magnitude than F₂, the box will accelerate backward because the net force is in the backward direction (1st option)

To obtain the direction in which the box will move, we shall determine the net force acting on the box. This is illustrated below:

Assumption:

Net force = Magnitude of force 1 (F₁) - Magnitude of force 2 (F₂)

Net force = F₁ - F₂

Net force = 40 - 25

Net force = 15 N backward

From the above illustration, we can see that the net force is 15 N backward.

Thus, we can conclude from the box will accelerate backward (1st option)

Learn more about net force:

https://brainly.com/question/12282988

#SPJ1

Answer:

Explanation:

First, we need to use the formula for the speed of an object in circular orbit:

v = sqrt(GM/R)

where G is the gravitational constant, M is the mass of the Earth, R is the distance between the center of the Earth and the satellite.

Converting the units to meters and kilograms:

G = 6.67 × 10^-11 m^3/kg s^2

M = 5.98 × 10^24 kg

R = (36000 + 6.37 × 10^6) × 1000 = 4.23 × 10^7 m

Plugging in the values:

v = sqrt((6.67 × 10^-11) × (5.98 × 10^24) / (4.23 × 10^7))

v ≈ 3075.58 m/s

Finally, we can convert this to miles per hour:

v = 3075.58 m/s x (3600 s/hr) / (1609.34 m/mi) = 6873.18 mi/hr

Therefore, the answer is option A. 306889 mi/hr is incorrect.

There are two forces acting on the rock: the force of gravity pulling it downward and the force of the boulder supporting it from underneath.

The force of gravity is the gravitational attraction between the rock and the Earth. It pulls the rock downward with a force equal to its weight, which is given by the equation Fg = mg, where Fg is the force of gravity, m is the mass of the rock, and g is the acceleration due to gravity (approximately 9.81 m/s^2).

The concept of forces explains why the rock stays on top of the boulder because the forces are balanced. The force of gravity pulling the rock downward is equal and opposite to the force of the boulder supporting it from underneath. As a result, the rock remains in equilibrium, or a state of balance, on top of the boulder. If either force were to change, the equilibrium would be disrupted, and the rock would either fall to the ground or be pushed off the boulder.

To know more about forces visit:-

brainly.com/question/13191643

#SPJ1

Answer:

Explanation:

Assuming that air resistance is negligible, we can use the following kinematic equations to solve for the peak height:

v_f^2 = v_i^2 + 2ad

where v_f = 0 m/s (at the peak height) and a = -9.8 m/s^2 (acceleration due to gravity)

and

d = v_i t + (1/2)at^2

where d is the displacement or the peak height we want to find, v_i is the initial velocity, t is the time it takes to reach the peak height.

First, we need to resolve the initial velocity into its vertical and horizontal components:

v_i_x = v_i cos(30°) = 121.1 m/s

v_i_y = v_i sin(30°) = 70.0 m/s

Next, we can use the vertical component of the initial velocity to find the time it takes to reach the peak height:

v_f = v_i_y + at

0 m/s = 70.0 m/s + (-9.8 m/s^2)t

t = 7.14 s

Finally, we can use the time we found and the kinematic equation for displacement to find the peak height:

d = v_i_y t + (1/2)at^2

d = (70.0 m/s)(7.14 s) + (1/2)(-9.8 m/s^2)(7.14 s)^2

d = 247.5 m

Therefore, the peak height of the football is 247.5 meters.

Answer:24 volts ÷ 4 amps = 6 ohms

Explanation:

We know that the Ohm's law has given the relationship between the current, voltage and the resistance of the wire. Mathematically, it can be written as :

Where

I is the current

R is the resistance

If current flowing is 4 amps and voltage is 24 volts. The formula to find the resistance will be :

R = 6 Ohms

Hence, the correct option is (d) " 24 volts ÷ 4 amps = 6 ohms ".

The answer is:

D. 7.6m

Answer:

power plant

collision

Battery

Burning wood

speaker

Beating drum

Answer:

Pulse transfers a single disturbance, while wave is a continuous disturbance that transfers energy.

If you found this response helpful, please consider marking it as brainliest.

The spring scale read just before the mass touches the lower spring is 80.36N, the spring constant for the lower spring is 2765N/m and at 2.9cm length the scale will read zero.

Given the mass of spring = 8.2kg

The force exerted for compressing of spring = 14N

The compression in spring = 2.4cm = 0.024m

(A.) Initially the spring scale reads only the weight of the mass = mg

W = 8.2 * 9.8 = 80.36N

(B) Let the value of spring constant = k

The net force exerted so that the scale reads(F') = 80.36N - 14 = 66.36N

We know that according to Hooke's law the force exerted on spring F = kx such that:

F' = kx then:

66.36 = k * 0.024

k = 66.36/0.024 = 2765N/m

(C) the compression where scale reads zero = x'

The scale reads zero when the restoring force equals to the weight of the mass then the scale reads zero such that:

x' = 80.36/2765 = 0.029m = 2.9cm

To learn more about spring constant click here https://brainly.com/question/14159361

#SPJ1

Answer : 0.00885 farads or 8.85 microfarads

Explanation: To calculate the capacitance required, we can use the following formula:

C = 1 / [2 * pi * f * ((V^2 - Vlamp^2)/P)]

where:

C = capacitance in farads (F)

pi = 3.14159...

f = frequency in hertz (Hz)

V = voltage in volts (V)

P = power in watts (W)

Vlamp = voltage of the lamp in volts (V)

Using the given values, we have:

C = 1 / [2 * pi * 60 * ((230^2 - 100^2)/750)]

C = 1 / [2 * 3.14159 * 60 * ((230^2 - 100^2)/750)]

C = 1 / [113.09724]

C = 0.00885 farads (F)

Therefore, the capacitance required is approximately 0.00885 farads or 8.85 microfarads.

Answer:

13.8 (kgm)/s

Explanation:

p(momentum) = m (mass) * v (velocity)

p= 2.3 * 6

p = 13.8

The two gases that could be components of water are indeed hydrogen and oxygen.

Evidence to support this claim:

1. The chemical formula for water is H2O, which means that it is composed of two hydrogen atoms and one oxygen atom.

2. The table of elements shows that hydrogen (H) and oxygen (O) are both elements that exist in nature.

3. The atomic mass of hydrogen (1.008) and oxygen (15.999) matches the molecular mass of water (18.015).

4. Water is produced when hydrogen gas (H2) is burned in the presence of oxygen gas (O2), according to the following equation: 2H2 + O2 → 2H2O.

Overall, the evidence supports the conclusion that hydrogen and oxygen are the two gases that could be components of water.

To know more about water please refer: https://brainly.com/question/31037355

#SPJ1

The bigger the spring constant, the more stiff or rigid the spring is.

The exact amount of force needed to bend a spring depends on the spring constant. Although pounds/inch is a common measurement in North America, the standard international (SI) unit for spring constants is Newtons/meter. A stiffer spring has a greater spring constant, and vice versa.

The exact amount of force needed to bend a spring depends on the spring constant. Although pounds/inch is a common measurement in North America, the standard international (SI) unit for spring constants is Newtons/meter. A stiffer spring has a greater spring constant, and vice versa.

To know more about spring constant visit:-

https://brainly.com/question/14159361

#SPJ9

The truck's acceleration is 3.0m/s² and the momentum of the truck is  144000 kg m/s.

It is the rate at which the speed and direction of a moving object vary over time.

We can use the following equation to calculate the acceleration of the truck:

a = (v - u) / t

where

a = acceleration

v = final velocity = 18.0 m/s

u = initial velocity = 0 m/s (the truck starts from rest)

t = time taken = 6.00 s

Substituting the values, we get:

a = (18.0 m/s - 0 m/s) / 6.00 s

a = 3.00 m/s²

Therefore, the acceleration of the truck is 3.00 m/s².

We can use the following equation to calculate the momentum of the truck:

p = m * v

where

p = momentum

m = mass of the truck = 8000.0 kg

v = final velocity = 18.0 m/s

Substituting the values, we get:

p = 8000.0 kg * 18.0 m/s

p = 144000 kg m/s

Therefore, the momentum of the truck after it has reached its final velocity is 144000 kg m/s.

Learn more about velocity here:

https://brainly.com/question/17127206

#SPJ9

Answer: b. force per unit area.

Explanation:

Answer:

Astronomers use computer models to simulate the process of galactic evolution through mergers and collisions. These models are based on our current understanding of the physical laws that govern the behavior of matter and energy in the universe. By running simulations of galactic mergers and collisions, astronomers can test their understanding of how these physical processes work in practice and how they contribute to the formation and evolution of galaxies.

One way that astronomers might test their understanding of the physical processes of the universe is by comparing the predictions of their models to observations of real galaxies. For example, if a model predicts that a particular type of galaxy should have a certain shape, size, or distribution of stars, astronomers can compare these predictions to observations of actual galaxies to see if they match up. If there is a discrepancy between the model's predictions and the observations, this can indicate that there are some physical processes that are not well understood or included in the model.

Another way that astronomers might test their understanding is by looking for patterns or trends in the properties of galaxies that are consistent with the predictions of their models. For example, if a model predicts that galaxies that have undergone a recent merger should have a particular distribution of gas and dust, astronomers can look for evidence of this pattern in observations of real galaxies. If they find that the predicted pattern is consistently observed in a large sample of galaxies, this can provide support for the model's predictions and the physical processes that it includes.

Overall, computer models of galactic evolution through mergers and collisions provide a powerful tool for astronomers to test their understanding of the physical processes of the universe. By comparing the predictions of their models to observations of real galaxies and looking for consistent patterns and trends, astronomers can refine their understanding of how galaxies form and evolve over time.

The speed of the wind is 20 miles per hour.

To solve this problem, we can use the formula:

Speed = Distance/Time

Let's assume that the speed of the wind is x miles per hour.

With the wind, the plane travels at a speed of 460 miles per hour. This means that its speed relative to the ground is the sum of its airspeed and the speed of the wind:

460 = Airspeed + x

Against the wind, the plane travels at a speed of 420 miles per hour. This means that its speed relative to the ground is the difference between its airspeed and the speed of the wind:

420 = Airspeed - x

We can solve this system of equations to find the airspeed of the plane:

460 = Airspeed + x

420 = Airspeed - x

Adding the two equations gives:

880 = 2Airspeed

Dividing both sides by 2 gives:

Airspeed = 440 miles per hour

Now that we know the airspeed of the plane, we can find the speed of the wind by substituting this value into one of the equations we obtained earlier:

460 = Airspeed + x

460 = 440 + x

x = 20

To learn more about speed visit;

https://brainly.com/question/28224010

#SPJ9