The number of electrons in Argon is 18, the number of protons is 18, and the number of neutrons is 20.
Now, let's proceed to the second part of the question. Here's how to determine the number of electrons, protons, and neutrons in Argon 38 :18 Ar :Since the atomic number of Argon is 18, it has 18 protons in its nucleus, which is also equal to its atomic number.
Since Argon is neutral, it has 18 electrons orbiting around its nucleus.In order to determine the number of neutrons, we have to subtract the number of protons from the atomic mass. In this case, the atomic mass of Argon is 38.
Therefore: Number of neutrons = Atomic mass - Number of protons Number of neutrons = 38 - 18 Number of neutrons = 20 Therefore, the number of electrons in Argon is 18, the number of protons is 18, and the number of neutrons is 20
Know more about electrons here:
https://brainly.com/question/12001116
#SPJ11
On a day when the speed of sound is 345 m/s, the fundamental frequency of a particular stopped organ pipe is 220 Hz. The second overtone of this pipe has the same wavelength as the third harmonic of an open pipe. How long is the open pipe? Express your answer in mm
The length of the open pipe can be determined by comparing the wavelength of the third harmonic of the open pipe to the second overtone of the stopped organ pipe.
The fundamental frequency of a stopped organ pipe is determined by the length of the pipe, while the frequency of a harmonic in an open pipe is determined by the length and speed of sound. In this case, the fundamental frequency of the stopped organ pipe is given as 220 Hz.
The second overtone of the stopped organ pipe is the third harmonic, which has a frequency that is three times the fundamental frequency, resulting in 660 Hz (220 Hz × 3). The wavelength of this second overtone can be calculated by dividing the speed of sound by its frequency: wavelength = speed of sound / frequency = 345 m/s / 660 Hz = 0.5227 meters.
Now, we need to find the length of the open pipe that produces the same wavelength as the third harmonic of the stopped organ pipe. Since the open pipe has a fundamental frequency that corresponds to its first harmonic, the wavelength of the third harmonic in the open pipe is four times the length of the pipe. Therefore, the length of the open pipe can be calculated by multiplying the wavelength by a factor of 1/4: length = (0.5227 meters) / 4 = 0.1307 meters.
Finally, to express the length in millimeters, we convert the length from meters to millimeters by multiplying it by 1000: length = 0.1307 meters × 1000 = 130.7 mm. Hence, the length of the open pipe is 130.7 mm.
To learn more about wavelength.
Click here:brainly.com/question/29548846
#SPJ11
A copper wire has a length of 1.50 m and a cross sectional area of 0.280 mm? If the resistivity of copper is 1.70 x 100 m and a potential difference of 0.100 Vis maintained across as length determine the current in the wire (in A)
The current in the copper wire is approximately 0.01096 A (or 10.96 mA).
To determine the current in the copper wire, we can use Ohm's Law, which states that the current (I) flowing through a conductor is equal to the potential difference (V) across the conductor divided by the resistance (R).
In this case, the resistance (R) of the copper wire can be calculated using the formula:
R = (ρ * L) / A
Where:
ρ is the resistivity of copper (1.70 x 10^-8 Ω·m)
L is the length of the wire (1.50 m)
A is the cross-sectional area of the wire (0.280 mm² = 2.80 x 10^-7 m²)
Substituting the given values into the formula, we have:
R = (1.70 x 10^-8 Ω·m * 1.50 m) / (2.80 x 10^-7 m²)
R ≈ 9.11 Ω
Now, we can calculate the current (I) using Ohm's Law:
I = V / R
Substituting the given potential difference (V = 0.100 V) and the calculated resistance (R = 9.11 Ω), we have:
I = 0.100 V / 9.11 Ω
I ≈ 0.01096 A (or approximately 10.96 mA)
Therefore, the current in the copper wire is approximately 0.01096 A (or 10.96 mA).
Learn more about Ohm's Law from the given link
https://brainly.com/question/14296509
#SPJ11
Questions 7.39 Homework. Unanswered ★ A pendulum is fashioned out of a thin bar of length 0.55 m and mass 1.9 kg. The end of the bar is welded to the surface of a sphere of radius 0.11 m and mass 0.86 kg. Find the centre of mass of the composite object as measured in metres from the end of the bar without the sphere. Type your numeric answer and submit
The center of mass of the composite object, consisting of the bar and sphere, is approximately 0.206 meters from the end of the bar. This is calculated by considering the individual centers of mass and their weighted average based on their masses.
To find the center of mass of the composite object, we need to consider the individual center of masses of the bar and the sphere and calculate their weighted average based on their masses.
The center of mass of the bar is located at its midpoint, which is L/2 = 0.55 m / 2 = 0.275 m from the end of the bar.
The center of mass of the sphere is at its geometric center, which is at a distance of R/2 = 0.11 m / 2 = 0.055 m from the end of the bar.
Now we calculate the weighted average:
Center of mass of the composite object = ([tex]m_bar[/tex] * center of mass of the bar + [tex]m_bar[/tex] * center of mass of the sphere) / ([tex]m_bar + m_sphere[/tex])
Center of mass of the composite object = (1.9 kg * 0.275 m + 0.86 kg * 0.055 m) / (1.9 kg + 0.86 kg)
To solve the expression (1.9 kg * 0.275 m + 0.86 kg * 0.055 m) / (1.9 kg + 0.86 kg), we can simplify the numerator and denominator separately and then divide them.
Numerator: (1.9 kg * 0.275 m + 0.86 kg * 0.055 m) = 0.5225 kg⋅m + 0.0473 kg⋅m = 0.5698 kg⋅m
Denominator: (1.9 kg + 0.86 kg) = 2.76 kg
Now we can calculate the expression:
(0.5698 kg⋅m) / (2.76 kg) ≈ 0.206 m
Therefore, the solution to the expression is approximately 0.206 meters.
To know more about the center of mass refer here,
https://brainly.com/question/8662931#
#SPJ11
A rod of negligible resistance is sliding along a pair of long tracks--also of negligible resistance. The tracks are connected on one end by a wire of resistance R, the rod is sliding away from this end at constant speed, and there is a uniform magnetic field which points in a direction perpendicular to the plane containing the rod and the tracks. Initially, the area bounded by the rod, the tracks, and the end is A1, but after some time the area is A2 = 3A1. At this initial time, the induced emf was 3.0 V. What will it be at the latter time, when the total enclosed area has tripled?
The induced emf will be 9.0 V when the total enclosed area has tripled.
According to Faraday's law of electromagnetic induction, the induced emf (ε) in a circuit is proportional to the rate of change of magnetic flux through the circuit. The magnetic flux (Φ) is given by the product of the magnetic field (B) and the area (A) enclosed by the circuit.
In this scenario, the initially induced emf (ε1) is 3.0 V, and the initial area (A1) is known. When the total enclosed area becomes A2 = 3A1, it means the area has tripled. Since the speed of the rod is constant, the rate of change of area is also constant.
Therefore, the ratio of the final area (A2) to the initial area (A1) is equal to the ratio of the final induced emf (ε2) to the initial induced emf (ε1).
Mathematically, we can express this relationship as:
A2/A1 = ε2/ε1
Substituting the known values, A2 = 3A1 and ε1 = 3.0 V, we can solve for ε2:
3A1/A1 = ε2/3.0 V
3 = ε2/3.0 V
Cross-multiplying, we find:
ε2 = 9.0 V
Hence, the induced emf will be 9.0 V when the total enclosed area has tripled.
To learn more about magnetic flux
Click here brainly.com/question/1596988
#SPJ11
Two identical sinusoidal waves with wavelengths of 3 m travel in the same
direction at a speed of 100 m/s. If both waves originate from the same starting
position, but with time delay At, and the resultant amplitude A_res = V3 A then At
will be equal to:
Two identical sinusoidal waves with wave lengths of 3.00 m travel in the same direction at a speed of 2.00 m/s. The second wave originates from the same point as the first, but at a later time. The minimum possible time interval between the starting moments of the two waves is approximately 0.2387 seconds.
To determine the minimum possible time interval between the starting moments of the two waves, we need to consider their phase difference and the condition for constructive interference.
Let's analyze the problem step by step:
Given:
Wavelength of the waves: λ = 3.00 m
Wave speed: v = 2.00 m/s
Amplitude of the resultant wave: A_res = A (same as the amplitude of each initial wave)
First, we can calculate the frequency of the waves using the formula v = λf, where v is the wave speed and λ is the wavelength:
f = v / λ = 2.00 m/s / 3.00 m = 2/3 Hz
The time period (T) of each wave can be determined using the formula T = 1/f:
T = 1 / (2/3 Hz) = 3/2 s = 1.5 s
Now, let's assume that the second wave starts at a time interval Δt after the first wave.
The phase difference (Δφ) between the two waves can be calculated using the formula Δφ = 2πΔt / T, where T is the time period:
Δφ = 2πΔt / (1.5 s)
According to the condition for constructive interference, the phase difference should be an integer multiple of 2π (i.e., Δφ = 2πn, where n is an integer) for the resultant amplitude to be the same as the initial wave amplitude.
So, we can write:
2πΔt / (1.5 s) = 2πn
Simplifying the equation:
Δt = (1.5 s / 2π) × n
To find the minimum time interval Δt, we need to find the smallest integer n that satisfies the condition.
Since Δt represents the time interval, it should be a positive quantity. Therefore,the smallest positive integer value for n would be 1.
Substituting n = 1:
Δt = (1.5 s / 2π) × 1
Δt = 0.2387 s (approximately)
Therefore, the minimum possible time interval between the starting moments of the two waves is approximately 0.2387 seconds.
To learn more about amplitude visit: https://brainly.com/question/3613222
#SPJ11
The question should be :
Two identical sinusoidal waves with wave lengths of 3.00 m travel in the same direction at a speed of 2.00 m/s. The second wave originates from the same point as the first, but at a later time. The amplitude of the resultant wave is the same as that of each of the two initial waves. Determine the minimum possible time interval (in sec) between the starting moments of the two waves.
A proton is moving north at a velocity of 4.9-10 m/s through an east directed magnetic field. The field has a strength of 9.6-10 T. What is the direction and strength of the magnetic force?
The direction of the magnetic force is towards the west, and its strength is [tex]7.7 * 10^{-28}[/tex] N.
Given data, Velocity of proton, v = 4.9 × 10⁻¹⁰ m/s
Strength of magnetic field, B = 9.6 × 10⁻¹⁰ T
We know that the magnetic force is given by the equation:
F = qvBsinθ
where, q = charge of particle, v = velocity of particle, B = magnetic field strength, and θ = angle between the velocity and magnetic field vectors.
Now, the direction of the magnetic force can be determined using Fleming's left-hand rule. According to this rule, if we point the thumb of our left hand in the direction of the velocity vector, and the fingers in the direction of the magnetic field vector, then the direction in which the palm faces is the direction of the magnetic force.
Therefore, using Fleming's left-hand rule, the direction of the magnetic force is towards the west (perpendicular to the velocity and magnetic field vectors).
Now, substituting the given values, we have:
[tex]F = (1.6 * 10^{-19} C)(4.9 * 10^{-10} m/s)(9.6 *10^{-10} T)sin 90°F = 7.7 * 10^{-28} N[/tex]
Thus, the direction of the magnetic force is towards the west, and its strength is [tex]7.7 * 10^{-28}[/tex] N.
Learn more about " magnetic force " refer to the link : https://brainly.com/question/26257705
#SPJ11
A normal person has a near point at 25 cm and a far point at infinity. Suppose a nearsighted person has a far point at 157 cm. What power lenses would prescribe?
To correct the nearsightedness of a person with a far point at 157 cm, lenses with a power of approximately -0.636 diopters (concave) should be prescribed. Consultation with an eye care professional is important for an accurate prescription and fitting.
To determine the power of lenses required to correct the nearsightedness of a person, we can use the formula:
Lens Power (in diopters) = 1 / Far Point (in meters)
Given that the far point of the nearsighted person is 157 cm (which is 1.57 meters), we can substitute this value into the formula:
Lens Power = 1 / 1.57 = 0.636 diopters
Therefore, a nearsighted person with a far point at 157 cm would require lenses with a power of approximately -0.636 diopters. The negative sign indicates that the lenses need to be concave (diverging) in nature to help correct the person's nearsightedness.
These lenses will help diverge the incoming light rays, allowing them to focus properly on the retina, thus improving distance vision for the individual. It is important for the individual to consult an optometrist or ophthalmologist for an accurate prescription and proper fitting of the lenses based on their specific needs and visual acuity.
To learn more about lenses
https://brainly.com/question/28039799
#SPJ11
A hollow square steel tube has a height and width dimension of 5 in and a wall thickness of 0.4 in. and an original length of 8 in. The tube is loaded with 44000 lb. in compression and is shortened by 0.0017 in. as a result of the load. Determine the Modulus of Elasticity of the steel with 1-decimal place accuracy.E= _______ x10^6
(to 1 decimal place)
The Modulus of Elasticity of the steel with 1-decimal place accuracy is 0.0017 in / 8 in
To determine the modulus of elasticity (E) of the steel, we can use Hooke's law, which states that the stress (σ) is directly proportional to the strain (ε) within the elastic limit.
The stress (σ) can be calculated using the formula:
σ = F / A
Where:
F is the force applied (44000 lb in this case)
A is the cross-sectional area of the steel tube.
The strain (ε) can be calculated using the formula:
ε = ΔL / L0
Where:
ΔL is the change in length (0.0017 in)
L0 is the original length (8 in)
The modulus of elasticity (E) can be calculated using the formula:
E = σ / ε
Now, let's calculate the cross-sectional area (A) of the steel tube:
The outer dimensions of the tube can be calculated by adding twice the wall thickness to each side of the inner dimensions:
Outer height = 5 in + 2 × 0.4 in = 5.8 in
Outer width = 5 in + 2 × 0.4 in = 5.8 in
The cross-sectional area (A) is the product of the outer height and outer width:
A = Outer height × Outer width
Substituting the values:
A = 5.8 in × 5.8 in
A = 33.64 in²
Now, we can calculate the stress (σ):
σ = 44000 lb / 33.64 in²
Next, let's calculate the strain (ε):
ε = 0.0017 in / 8 in
Finally, we can calculate the modulus of elasticity (E):
E = σ / ε
To know more about elasticity click on below link :
https://brainly.com/question/17250844#
#SPJ11
Four charged spheres, with equal charges of +2.30 C, are
situated in corner positions of a square of 60 cm. Determine the
net electrostatic force on the charge in the top right corner of
the square.
The net electrostatic force on the charge in the top right corner of the square is 8.91 x 10⁶ N at an angle of 14.0° above the horizontal.
The expression for the electrostatic force between two charged spheres is:
F=k(q₁q₂/r²)
Where, k is the Coulomb constant, q₁ and q₂ are the charges of the spheres and r is the distance between their centers.
The magnitude of each force is:
F=k(q₁q₂/r²)
F=k(2.30C x 2.30C/(0.60m)²)
F=8.64 x 10⁶ N3. If F₁, F₂, and F₃ are the magnitudes of the forces acting along the horizontal and vertical directions respectively, then the net force along the horizontal direction is:
Fnet=F₁ - F₂
Since the charges in the top and bottom spheres are equidistant from the charge in the top right corner, their forces along the horizontal direction will be equal in magnitude and opposite in direction, so:
F/k(2.30C x 2.30C/(0.60m)²)
= 8.64 x 10⁶ N4.
The net force along the vertical direction is: F
=F₃
= F/k(2.30C x 2.30C/(1.20m)²)
= 2.16 x 10⁶ N5.
Fnet=√(F₁² + F₃²)
= √((8.64 x 10⁶)² + (2.16 x 10⁶)²)
= 8.91 x 10⁶ N6.
The direction of the net force can be obtained by using the tangent function: Ftan=F₃/F₁= 2.16 x 10⁶ N/8.64 x 10⁶ N= 0.25tan⁻¹ (0.25) = 14.0° above the horizontal
Therefore, the net electrostatic force on the charge in the top right corner of the square is 8.91 x 10⁶ N at an angle of 14.0° above the horizontal.
To know more about electrostatic force please refer:
https://brainly.com/question/20797960
#SPJ11
SOLID STATE PHYSICS - ASHCROFT/MERMIN Each partially filled band makes such a contribution to the current density; the total current density is the sum of these contributions over all bands. From (13.22) and (13.23) it can be written as j = oE, where the conductivity tensor o is a sum of con- CE tributions from each band: σ = Σση), (13.24) n ت % ) در جاده اهر - dk olm e2 Senat - » e.com (E,(k))v,(k),(k) (13.25) E=E/) 2. Deduce from (13.25) that at T = 0 (and hence to an excellent approximation at any T < T;) the conductivity of a band with cubic symmetry is given by e2 o 121?h T(E)US, (13.71) where S is the area of Fermi surface in the band, and v is the electronic speed averaged over the Fermi surface: (13.72) ſas pras). (Note that this contains, as a special case, the fact that filled or empty bands (neither of which have any Fermi surface) carry no current. It also provides an alternative way of viewing the fact that almost empty (few electrons) and almost filled (few holes) bands have low conductivity, since they will have very small amounts of Fermi surface.) Verify that (13.71) reduces to the Drude result in the free electron limit.
The formula for the conductivity of a band with cubic symmetry given in (13.71) is e2 o 121.
The h T(E)US, (13.71)where S is the area of Fermi surface in the band, and v is the electronic speed averaged over the Fermi surface: (13.72) ſas pras.The question requires us to verify that (13.71) reduces to the Drude result in the free electron limit. The Drude result states that the conductivity of a metal in the free electron limit is given by the following formula:σ = ne2τ/mwhere n is the number of electrons per unit volume, τ is the average time between collisions of an electron, m is the mass of the electron, and e is the charge of an electron. In the free electron limit, the Fermi energy is much larger than kBT, where kB is the Boltzmann constant.
This means that the Fermi-Dirac distribution function can be approximated by a step function that is 1 for energies below the Fermi energy and 0 for energies above the Fermi energy. In this limit, the integral over k in (13.25) reduces to a sum over states at the Fermi surface. Therefore, we can write (13.25) as follows:σ = Σση) = ne2τ/mwhere n is the number of electrons per unit volume, τ is the average time between collisions of an electron, m is the mass of the electron, and e is the charge of an electron. Comparing this with (13.71), we see that it reduces to the Drude result in the free electron limit. Therefore, we have verified that (13.71) reduces to the Drude result in the free electron limit.
To know more about conductivity:
https://brainly.com/question/31201773
#SPJ11
If the period of a 70.0-cm-long simple pendulum is 1.68 s, what
is the value of g at the location of the pendulum?
The value of g at the location of the pendulum is approximately 9.81 m/s², given a period of 1.68 s and a length of 70.0 cm.
The period of a simple pendulum is given by the formula:
T = 2π√(L/g),
where:
T is the period,L is the length of the pendulum, andg is the acceleration due to gravity.Rearranging the formula, we can solve for g:
g = (4π²L) / T².
Substituting the given values:
L = 70.0 cm = 0.70 m, and
T = 1.68 s,
we can calculate the value of g:
g = (4π² * 0.70 m) / (1.68 s)².
g ≈ 9.81 m/s².
Therefore, the value of g at the location of the pendulum is approximately 9.81 m/s².
To learn more about acceleration due to gravity, Visit:
https://brainly.com/question/88039
#SPJ11
2. A shell is fired from a cliff horizontally with initial velocity of 800 m/s at a target on the ground 150 m below. How far away is the target? ( 2 pts) 3. You are standing 50 feet from a building and throw a ball through a window that is 26 feet above the ground. Your release point is 6 feet off of the ground (hint: you are only concerned with Δ y). You throw the ball at 30ft/sec. At what angle from the horizontal should you throw the ball? (hint: this is your launch angle) (2pts)
Horizontal displacement = 4008 meters
The launch angle should be approximately 20.5°
To find how far away the target is, the horizontal displacement of the shell needs to be found.
This can be done using the formula:
horizontal displacement = initial horizontal velocity x time
The time taken for the shell to reach the ground can be found using the formula:
vertical displacement = initial vertical velocity x time + 0.5 x acceleration x time^2
Since the shell is fired horizontally, its initial vertical velocity is 0. The acceleration due to gravity is 9.8 m/s^2. The vertical displacement is -150 m (since it is below the cliff).
Using these values, we get:-150 = 0 x t + 0.5 x 9.8 x t^2
Solving for t, we get:t = 5.01 seconds
The horizontal displacement is therefore:
horizontal displacement = 800 x 5.01
horizontal displacement = 4008 meters
3. To find the launch angle, we can use the formula:
Δy = (v^2 x sin^2 θ)/2g Where Δy is the vertical displacement (26 ft), v is the initial velocity (30 ft/s), g is the acceleration due to gravity (32 ft/s^2), and θ is the launch angle.
Using these values, we get:26 = (30^2 x sin^2 θ)/2 x 32
Solving for sin^2 θ:sin^2 θ = (2 x 26 x 32)/(30^2)sin^2 θ = 0.12
Taking the square root:sin θ = 0.35θ = sin^-1 (0.35)θ = 20.5°
Therefore, the launch angle should be approximately 20.5°.
Note: The given measurements are in feet, but the calculations are done in fps (feet per second).
Learn more about horizontal displacement here https://brainly.com/question/6107697
#SPJ11
Astronomers measure the distance to a particular star to
be 6.0 light-years (1 ly = distance light travels in 1 year). A spaceship travels from Earth to the vicinity of this star at steady speed, arriving in 3.50 years as measured by clocks on the spaceship. (a) How long does the trip take as measured by clocks in Earth's reference frame? (b) What distance does the spaceship travel as measured in its own
reference frame?
The time taken by the spaceship as measured by Earth's reference frame can be calculated as follows: Δt′=Δt×(1−v2/c2)−1/2 where:v is the speed of the spaceship as measured in Earth's reference frame, c is the speed of lightΔt is the time taken by the spaceship as measured in its own reference frame.
The value of v is calculated as follows: v=d/Δt′where:d is the distance between Earth and the star, which is 6.0 light-years. Δt′ is the time taken by the spaceship as measured by Earth's reference frame.Δt is given as 3.50 years.Substituting these values, we get :v = d/Δt′=6.0/3.50 = 1.71 ly/yr.
Using this value of v in the first equation v is speed, we can find Δt′:Δt′=Δt×(1−v2/c2)−1/2=3.50×(1−(1.71)2/c2)−1/2=3.50×(1−(1.71)2/1)−1/2=2.42 years. Therefore, the trip takes 2.42 years as measured by clocks in Earth's reference frame.
The distance traveled by the spaceship as measured in its own reference frame is equal to the distance between Earth and the star, which is 6.0 light-years. This is because the spaceship is at rest in its own reference frame, so it measures the distance to the star to be the same as the distance measured by Earth astronomers.
Learn more about speed:
brainly.com/question/13943409
#SPJ11
Imagine you had a device to use for this experiment. The device would shoot a series of 2. 0 g balls along the surface at the box, each with a velocity of 30 cm/s [E60N]. In 2. 0 s it shoots 10 successive 2. 0 balls, all of which collide and rebound off the 100g box, as with the first ball. What would be the total impulse delivered to the box by the 10 collisions?What would be the total change in momentum of the 100g box?What would be the total change in velocity of the 100g box after these 10 collisions?
The total impulse delivered to the box by the 10 collisions is 0.006 kg·m/s, the total change in momentum of the 100 g box is 0.012 kg·m/s, and the total change in velocity of the 100 g box after these 10 collisions is 0.12 m/s.
The total impulse delivered to the box by the 10 collisions can be calculated using the equation:
Impulse = Change in Momentum
First, let's calculate the momentum of each 2.0 g ball. The momentum of an object is given by the equation:
Momentum = mass x velocity
Since the mass of each ball is 2.0 g and the velocity is 30 cm/s, we convert the mass to kg and the velocity to m/s:
mass = 2.0 g = 0.002 kg
velocity = 30 cm/s = 0.3 m/s
Now, we can calculate the momentum of each ball:
Momentum = 0.002 kg x 0.3 m/s = 0.0006 kg·m/s
Since 10 balls are shot in succession, the total impulse delivered to the box is the sum of the impulses from each ball. Therefore, we multiply the momentum of each ball by the number of balls (10) to find the total impulse:
Total Impulse = 0.0006 kg·m/s x 10 = 0.006 kg·m/s
Next, let's calculate the total change in momentum of the 100 g box. The initial momentum of the box is zero since it is at rest. After each collision, the box gains momentum in the opposite direction to the ball's momentum. Since the box rebounds off the ball with the same momentum, the change in momentum for each collision is twice the momentum of the ball. Therefore, the total change in momentum of the box is:
Total Change in Momentum = 2 x Total Impulse = 2 x 0.006 kg·m/s = 0.012 kg·m/s
Finally, let's calculate the total change in velocity of the 100 g box after these 10 collisions. The change in velocity can be found using the equation:
Change in Velocity = Change in Momentum / Mass
The mass of the box is 100 g = 0.1 kg. Therefore, the total change in velocity is:
Total Change in Velocity = Total Change in Momentum / Mass = 0.012 kg·m/s / 0.1 kg = 0.12 m/s
Therefore, the total impulse delivered to the box by the 10 collisions is 0.006 kg·m/s, the total change in momentum of the 100 g box is 0.012 kg·m/s, and the total change in velocity of the 100 g box after these 10 collisions is 0.12 m/s.
To more about velocity visit:
https://brainly.com/question/34025828
#SPJ11
A straight wire with length 2320cm carries a current 20A which is directed to the right and is perpendicular to an unknown uniform magnetic field B. A magnetic
force 31pN acts on a conductor which is directed downwards. A. Determine the magnitude and the direction of the magnetic field in the region
through which the current passes. B. If the angle between the current and the magnetic field is 54 this time, what would
be the new value of the magnitude of the new magnetic force?
a. The magnitude of the magnetic field is [tex]2.84 * 10^(^-^1^1^) Tesla.[/tex]
b. The new value of the magnitude of the magnetic force is [tex]4.49 * 10^(^-^1^1^)[/tex] Newtons.
How do we calculate?a.
F_ = BILsinθ
F_ = magnetic force,
B = magnetic field
I = current,
L = length of the wire,
θ = angle between the current and the magnetic field.
Current (I) = 20 A
Length of wire (L) = 2320 cm = 23.20 m
Magnetic force (F) = 31 pN = 31 x 10^(-12) N
B = F/ (ILsinθ)
B = ([tex]31 * 10^(^-^1^2)[/tex]) N) / (20 A x 23.20 m x sin(90°))
B = [tex]2.84 * 10^(^-^1^1^)[/tex] T
b.
F' = BILsinθ'
F' = ([tex]2.84 * 10^(^-^1^1^)[/tex]T) x (20 A) x (23.20 m) x sin(54°)
F' = 4.49 x 10^(-11) N
Learn more about magnetic field at:
https://brainly.com/question/14411049
#SPJ4
What is the resistance of a 12m long wire of 12 gauge copper
wire at room temperature? The resistivity of copper at room
temperature is 1.72 x 10-8 Ωm and the diameter of 12
gauge wire is 2.64 mm.
Approximately 3.867 ohms is the resistance of a 12m long wire of 12 gauge copper at room temperature.
To calculate the resistance of the copper wire, we can use the formula for resistance:
Resistance (R) = (ρ * length) / cross-sectional area
The resistivity of copper (ρ) at room temperature is 1.72 x 10^(-8) Ωm and the length of the wire (length) is 12 meters, we need to determine the cross-sectional area.
The gauge of the wire is given as 12 gauge, and the diameter (d) of a 12 gauge copper wire is 2.64 mm. To calculate the cross-sectional area, we can use the formula:
Cross-sectional area = π * (diameter/2)^2
Converting the diameter to meters, we have d = 2.64 x 10^(-3) m. By halving the diameter to obtain the radius (r), we find r = 1.32 x 10^(-3) m.
Now, we can calculate the cross-sectional area using the radius:
Cross-sectional area = π * (1.32 x 10^(-3))^2 ≈ 5.456 x 10^(-6) m^2
Finally, substituting the values into the resistance formula, we get:
Resistance (R) = (1.72 x 10^(-8) Ωm * 12 m) / (5.456 x 10^(-6) m^2)
≈ 3.867 Ω
Therefore, the resistance of a 12m long wire of 12 gauge copper at room temperature is approximately 3.867 ohms.
learn more about "resistance ":- https://brainly.com/question/17563681
#SPJ11
Why must hospital personnel wear special conducting shoes while working around oxygen in an operating room?What might happen if the personnel wore shoes with rubber soles?
Hospital personnel must wear special conducting shoes in operating rooms to prevent the buildup of static electricity, which could potentially ignite the highly flammable oxygen. Wearing shoes with rubber soles increases the risk of static discharge and should be avoided to ensure the safety of everyone in the operating room.
Hospital personnel must wear special conducting shoes while working around oxygen in an operating room because oxygen is highly flammable and can ignite easily. These special shoes are made of materials that conduct electricity, such as leather, to prevent the buildup of static electricity.
If personnel wore shoes with rubber soles, static electricity could accumulate on their bodies, particularly on their feet, due to the friction between the rubber soles and the floor. This static electricity could then discharge as a spark, potentially igniting the oxygen in the operating room.
By wearing conducting shoes, the static electricity is safely discharged to the ground, minimizing the risk of a spark that could cause a fire or explosion. The conducting materials in these shoes allow any static charges to flow freely and dissipate harmlessly. This precaution is crucial in an environment where oxygen is used, as even a small spark can lead to a catastrophic event.
To know more about friction visit:
https://brainly.com/question/28356847
#SPJ11
(a) Find the distance of the image from a thin diverging lens of focal length 30 cm if the object is placed 20 cm to the right of the lens. Include the correct sign. cm (b) Where is the image formed?
The image is formed on the same side of the object.
Focal length, f = -30 cm
Distance of object from the lens, u = -20 cm
Distance of the image from the lens, v = ?
Now, using the lens formula, we have:
1/f = 1/v - 1/u
Or, 1/-30 = 1/v - 1/-20
Or, v = -60 cm (distance of image from the lens)
The negative sign of the image distance indicates that the image formed is virtual, erect, and diminished.
The image is formed on the same side of the object. So, the image is formed 60 cm to the left of the lens.
To learn more about image, refer below:
https://brainly.com/question/30725545
#SPJ11
Hoover Dam on the Colorado River is the highest dam in the United States at 221 m, with an output of 1300MW. The dam generates electricity with water taken from a depth of 151 m and an average flow rate of 620 m 3
/s. (a) Calculate the power in this flow. Report your answer in Megawatts 1,000,000 W =1MW 25. Hoover Dam on the Colorado River is the highest dam in the United States at 221 m, with an output of 1300MW. The dam generates electricity with water taken from a depth of 150 m and an average flow rate of 650 m 3
/s. (a) Calculate the power in this flow. (b) What is the ratio of this power to the facility's average of 680 MW? (These are the same values as the regular homework assignment) The ratio is 2.12 The ratio is 1.41 The ratio is 0.71 The ratio is 0.47
Hoover Dam on the Colorado River is the tallest dam in the United States, measuring 221 meters in height, with an output of 1300MW. The dam's electricity is generated by water that is taken from a depth of 151 meters and flows at an average rate of 620 m3/s.Therefore, the correct answer is the ratio is 1.41.
To compute the power in this flow, we use the formula:Power = (density) * (Volume flow rate) * (acceleration due to gravity) * (head). Where density is the density of water, which is 1000 kg/m3, and the acceleration due to gravity is 9.81 m/s2. Head = (depth) * (density) * (acceleration due to gravity). Substituting these values,Power = (1000 kg/m3) * (620 m3/s) * (9.81 m/s2) * (151 m) = 935929200 Watts. Converting this value to Megawatts,Power in Megawatts = 935929200 / 1000000 = 935.93 MWFor the second question,
(a) The power in the second flow is given by the formula:Power = (density) * (Volume flow rate) * (acceleration due to gravity) * (head)Where density is the density of water, which is 1000 kg/m3, and the acceleration due to gravity is 9.81 m/s2.Head = (depth) * (density) * (acceleration due to gravity) Power = (1000 kg/m3) * (650 m3/s) * (9.81 m/s2) * (150 m) = 956439000 Watts. Converting this value to Megawatts,Power in Megawatts = 956439000 / 1000000 = 956.44 MW
(b) The ratio of the power in this flow to the facility's average power is given by:Ratio of the power = Power in the second flow / Average facility power= 956.44 MW / 680 MW= 1.41. Therefore, the correct answer is the ratio is 1.41.
To know more about electricity visit:
brainly.com/question/31173598
#SPJ11
Find the force corresponding to the potential energy
U(x) =-a/x + b/x^2 + cx^2
The force corresponding to the potential energy function U(x) = -a/x + b/[tex]x^{2}[/tex] + c[tex]x^{2}[/tex] can be obtained by taking the derivative of the potential energy function with respect to x. The force corresponding to the potential energy function is F(x) = a/[tex]x^{2}[/tex] - 2b/[tex]x^{3}[/tex] + 2cx.
To find the force corresponding to the potential energy function, we differentiate the potential energy function with respect to position (x). In this case, we have U(x) = -a/x + b/[tex]x^{2}[/tex] + c[tex]x^{2}[/tex].
Taking the derivative of U(x) with respect to x, we obtain:
dU/dx = -(-a/[tex]x^{2}[/tex]) + b(-2)/[tex]x^{3}[/tex] + 2cx
Simplifying the expression, we get:
dU/dx = a/[tex]x^{2}[/tex] - 2b/[tex]x^{3}[/tex] + 2cx
This expression represents the force corresponding to the potential energy function U(x). The force is a function of position (x) and is determined by the specific values of the constants a, b, and c in the potential energy function.
To learn more about potential energy click here:
brainly.com/question/1455245
#SPJ11
A thermistor is used in a circuit to control a piece of equipment automatically. What might this circuit be used for? A lighting an electric lamp as it becomes darker B ringing an alarm bell if a locked door is opened C switching on a water heater at a pre-determined time D turning on an air conditioner when the temperature rises
A thermistor is used in a circuit to control a piece of equipment automatically, this circuit be used for D. Turn on an air conditioner when the temperature rises.
A thermistor is a type of resistor whose resistance value varies with temperature. In a circuit, it is used as a sensor to detect temperature changes. The thermistor is used to control a piece of equipment automatically in various applications like thermostats, heating, and cooling systems. A circuit with a thermistor may be used to turn on an air conditioner when the temperature rises. In this case, the thermistor is used to sense the increase in temperature, which causes the resistance of the thermistor to decrease.
This change in resistance is then used to trigger the circuit, which turns on the air conditioner to cool the room. A thermistor circuit may also be used to switch on a water heater at a pre-determined time. In this case, the thermistor is used to detect the temperature of the water, and the circuit is programmed to turn on the heater when the water temperature falls below a certain level. This helps to maintain a consistent temperature in the water tank. So therefore the correct answer is D, turn on an air conditioner when the temperature rises.
Learn more about thermistor at:
https://brainly.com/question/31888503
#SPJ11
How do the vibrational and rotational levels of heavy hydrogen (D²) molecules compare with those of H² molecules?
The vibrational and rotational levels of heavy hydrogen (D²) molecules are similar to those of H² molecules, but with some differences due to the difference in mass between hydrogen (H) and deuterium (D).
The vibrational and rotational levels of diatomic molecules are governed by the principles of quantum mechanics. In the case of H² and D² molecules, the key difference lies in the mass of the hydrogen isotopes.
The vibrational energy levels of a molecule are determined by the reduced mass, which takes into account the masses of both atoms. The reduced mass (μ) is given by the formula:
μ = (m₁ * m₂) / (m₁ + m₂)
For H² molecules, since both atoms are hydrogen (H), the reduced mass is equal to the mass of a single hydrogen atom (m_H).
For D² molecules, the reduced mass will be different since deuterium (D) has twice the mass of hydrogen (H).
Therefore, the vibrational energy levels of D² molecules will be shifted to higher energies compared to H² molecules. This is because the heavier mass of deuterium leads to a higher reduced mass, resulting in higher vibrational energy levels.
On the other hand, the rotational energy levels of diatomic molecules depend only on the moment of inertia (I) of the molecule. The moment of inertia is given by:
I = μ * R²
Since the reduced mass (μ) changes for D² molecules, the moment of inertia will also change. This will lead to different rotational energy levels compared to H² molecules.
The vibrational and rotational energy levels of heavy hydrogen (D²) molecules, compared to H² molecules, are affected by the difference in mass between hydrogen (H) and deuterium (D). The vibrational energy levels of D² molecules are shifted to higher energies due to the increased mass, resulting in higher vibrational states.
Similarly, the rotational energy levels of D² molecules will differ from those of H² molecules due to the change in moment of inertia resulting from the different reduced mass. These differences in energy levels arise from the fundamental principles of quantum mechanics and have implications for the spectroscopy and behavior of heavy hydrogen molecules compared to regular hydrogen molecules.
To know more about hydrogen ,visit:
https://brainly.com/question/24433860
#SPJ11
Singly charged uranium-238 ions are accelerated through a potential difference of 2.00kV and enter a uniform magnetic field of magnitude 1.20 T directed perpendicular to their velocities.(c) What If? How does the ratio of these path radii depend on the accelerating voltage?
The ratio of the path radii for the uranium-238 ions is not affected by the accelerating voltage. The ratio is solely determined by the mass of the ions and the magnitude of the magnetic field.
The ratio of the path radii for singly charged uranium-238 ions depends on the accelerating voltage.
When a charged particle enters a uniform magnetic field perpendicular to its velocity, it experiences a force called the magnetic force. This force acts as a centripetal force, causing the particle to move in a circular path.
The magnitude of the magnetic force is given by the equation:
F = qvB
Where:
F is the magnetic force
q is the charge of the particle
v is the velocity of the particle
B is the magnitude of the magnetic field
In this case, the uranium-238 ions have a charge of +1 (since they are singly charged). The magnetic force acting on the ions is equal to the centripetal force:
qvB = mv²/r
Where:
m is the mass of the uranium-238 ion
v is the velocity of the ion
r is the radius of the circular path
We can rearrange this equation to solve for the radius:
r = mv/qB
The velocity of the ions can be determined using the equation for the kinetic energy of a charged particle:
KE = (1/2)mv²
The kinetic energy can also be expressed in terms of the accelerating voltage (V) and the charge (q) of the ion:
KE = qV
We can equate these two expressions for the kinetic energy:
(1/2)mv² = qV
Solving for v, we get:
v = sqrt(2qV/m)
Substituting this expression for v into the equation for the radius (r), we have:
r = m(sqrt(2qV/m))/qB
Simplifying, we get:
r = sqrt(2mV)/B
From this equation, we can see that the ratio of the path radii is independent of the charge (q) of the ions and the mass (m) of the ions.
Therefore, the ratio of the path radii is independent of the accelerating voltage (V).
Learn more about voltage
https://brainly.com/question/32002804
#SPJ11
QUESTION 17 Doppler Part A A carousel that is 5.00 m in radius has a pair of 600-Hz sirens mounted on posts at opposite ends of a diameter. The carousel rotates with an angular velocity of 0.800 rad/s. A stationary listener is located at a distance from the carousel. The speed of sound is 350 m/s. What is the maximum frequency of the sound that reaches the listener?Give your answer accurate to 3 decimals. QUESTION 18 Doppler Parts What is the minimum frequency of sound that reaches the listener in Part A? Give your answer accurate to 3 decimals. QUESTION 19 Doppler Part what is the beat frequency heard in the problem mentioned in partA? Give your answer accurate to three decimals. Doppler Part D what is the orientation of the sirens with respect to the listener in part A when the maximum beat frequency is heard? Onone of the above the sirens and the listener are located along the same line. one siren is behind the other. the sirens and the listener form an isosceles triangle, both sirens are equidistant to the listener.
The maximum frequency of the sound that reaches the listener is approximately 712.286 Hz. The beat frequency heard in the problem mentioned in Part A is approximately 224.571 Hz.
Radius of the carousel (r) = 5.00 m
Frequency of the sirens (f) = 600 Hz
Angular velocity of the carousel (ω) = 0.800 rad/s
Speed of sound (v) = 350 m/s
(a) The maximum frequency occurs when the siren is moving directly towards the listener. In this case, the Doppler effect formula for frequency can be used:
f' = (v +[tex]v_{observer[/tex]) / (v + [tex]v_{source[/tex]) * f
Since the carousel is rotating, the velocity of the observer is equal to the tangential velocity of the carousel:
[tex]v_{observer[/tex] = r * ω
The velocity of the source is the velocity of sound:
[tex]v_{source[/tex]= v
Substituting the given values:
f' = (v + r * ω) / (v + v) * f
f' = (350 m/s + 5.00 m * 0.800 rad/s) / (350 m/s + 350 m/s) * 600 Hz
f' ≈ 712.286 Hz
Therefore, the maximum frequency of the sound that reaches the listener is approximately 712.286 Hz.
(b) Minimum Frequency of the Sound:
The minimum frequency occurs when the siren is moving directly away from the listener. Using the same Doppler effect formula:
f' = (v + [tex]v_{observer)[/tex] / (v - [tex]v_{source)[/tex] * f
Substituting the values:
f' = (v + r * ω) / (v - v) * f
f' = (350 m/s + 5.00 m * 0.800 rad/s) / (350 m/s - 350 m/s) * 600 Hz
f' ≈ 487.714 Hz
Therefore, the minimum frequency of the sound that reaches the listener is approximately 487.714 Hz.
(c) The beat frequency is the difference between the maximum and minimum frequencies:
Beat frequency = |maximum frequency - minimum frequency|
Beat frequency = |712.286 Hz - 487.714 Hz|
Beat frequency ≈ 224.571 Hz
Therefore, the beat frequency heard in the problem mentioned in Part A is approximately 224.571 Hz.
(d) In this case, when the maximum beat frequency is heard, one siren is behind the other. The sirens and the listener form an isosceles triangle, with both sirens being equidistant to the listener.
Learn more about sound here:
https://brainly.com/question/30045405
#SPJ11
An ice cube of volume 50 cm 3 is initially at the temperature 250 K. How much heat is required to convert this ice cube into room temperature (300 K)? Hint: Do not forget that the ice will be water at room temperature.
An ice cube of volume 50 cm³ is initially at the temperature of 250K. Let's find out how much heat is required to convert this ice cube into room temperature (300 K)
Solution:
It is given that the initial temperature of the ice cube is 250K and it has to be converted to room temperature (300K).
Now, we know that to convert ice at 0°C to water at 0°C, heat is required and the quantity of heat required is given byQ = mL
where, Q = Quantity of heat required, m = Mass of ice/water and L = Latent heat of fusion of ice at 0°C.
Now, to convert ice at 0°C to water at 0°C, heat is required.
The quantity of heat required is given by:
Q1 = mL1
Where, m = mass of ice
= Volume of ice × Density of ice
= (50/1000) × 917 = 45.85g(1 cm³ of ice weighs 0.917 g)
L1 = Latent heat of fusion of ice = 3.34 × 10⁵ J/kg (at 0°C)
Therefore,
Q1 = mL1 = (45.85/1000) × 3.34 × 10⁵
= 153.32 J
Now, the water formed at 0°C has to be heated to 300K (room temperature).
Heat required is given byQ2 = mCΔT
Where, m = mass of water
= 45.85 g (from above)
C = specific heat capacity of water = 4.2 J/gK (at room temperature)
ΔT = Change in temperature = (300 - 0) K
= 300 K
T = Temperature of water at room temperature = 300K
Therefore, Q2 = mCΔT= 45.85 × 4.2 × 300= 57834 J
Therefore, total heat required = Q1 + Q2= 153.32 J + 57834 J= 57987.32 J
Hence, the heat required to convert the ice cube of volume 50 cm³ at a temperature of 250K to water at a temperature of 300K is 57987.32 J.
To know more about temperature visit :
https://brainly.com/question/7510619
#SPJ11
50. The angle that a reflected light ray makes with the surface normal A) is smaller B) the same size C) greater than the angle that the incident ray makes with the normal 51. The speed of light in gl
The angle that a reflected light ray makes with the surface normal is smaller.
The law of reflection states that the angle of incidence is equal to the angle of reflection. When light is reflected from a surface, the angle at which it is reflected (angle of reflection) is equal to the angle at which it hits the surface (angle of incidence). The angle that a reflected light ray makes with the surface normal is the angle of reflection. Therefore, the answer is that the angle that a reflected light ray makes with the surface normal is smaller than the angle that the incident ray makes with the normal.
The speed of light in glass is less than the speed of light in a vacuum. This means that the refractive index of glass is greater than 1. When light passes through a medium with a higher refractive index than the medium it was previously in, the light is bent towards the normal. Therefore, the answer is that the speed of light in glass is less than the speed of light in a vacuum, and the refractive index of glass is greater than 1.
The angle that a reflected light ray makes with the surface normal is A) is smaller. The law of reflection states that the angle of incidence is equal to the angle of reflection. When light is reflected from a surface, the angle at which it is reflected (angle of reflection) is equal to the angle at which it hits the surface (angle of incidence). The angle that a reflected light ray makes with the surface normal is the angle of reflection. Therefore, the answer is that the angle that a reflected light ray makes with the surface normal is smaller than the angle that the incident ray makes with the normal.
The speed of light in glass is less than the speed of light in a vacuum. This means that the refractive index of glass is greater than 1. When light passes through a medium with a higher refractive index than the medium it was previously in, the light is bent towards the normal. Therefore, the answer is that the speed of light in glass is less than the speed of light in vacuum, and the refractive index of glass is greater than 1.
When a light wave strikes a surface, it can be either absorbed or reflected. Reflection occurs when light bounces back from a surface. The angle at which the light strikes the surface is known as the angle of incidence, and the angle at which it reflects is known as the angle of reflection. The angle of incidence is always equal to the angle of reflection, as stated by the law of reflection. The angle that a reflected light ray makes with the surface normal is the angle of reflection. It's smaller than the angle of incidence.
When light travels through different mediums, such as air and glass, its speed changes, and it bends. Refraction is the process of bending that occurs when light moves from one medium to another with a different density. The refractive index is a measure of the extent to which a medium slows down light compared to its speed in a vacuum. The refractive index of a vacuum is 1.
When light moves from a medium with a low refractive index to a medium with a high refractive index, it bends toward the normal, which is a line perpendicular to the surface separating the two media.
When light is reflected from a surface, the angle of reflection is always equal to the angle of incidence. The angle of reflection is the angle that a reflected light ray makes with the surface normal, and it is smaller than the angle of incidence. The refractive index of a medium is a measure of how much the medium slows down light compared to its speed in a vacuum. When light moves from a medium with a low refractive index to a medium with a high refractive index, it bends toward the normal.
To know more about refractive index visit
brainly.com/question/30761100
#SPJ11
: A student wishes to use a spherical concave mirror to make an astronomical telescope for taking pictures of distant galaxies. Where should the student locate the camera relative to the mirror? Infinitely far from the mirror Near the center of curvature of the mirror Near the focal point of the mirror On the surface of the mirror
The student should locate the camera at the focal point of the concave mirror to create an astronomical telescope for capturing pictures of distant galaxies.
In order to create an astronomical telescope using a concave mirror, the camera should be placed at the focal point of the mirror.
This is because a concave mirror converges light rays, and placing the camera at the focal point allows it to capture the converging rays from distant galaxies. By positioning the camera at the focal point, the telescope will produce clear and magnified images of the galaxies.
Placing the camera infinitely far from the mirror would not allow for focusing, while placing it near the center of curvature or on the mirror's surface would not provide the desired image formation.
To learn more about concave mirror click here: brainly.com/question/31379461
#SPJ11
1)How much energy would be required to convert 15.0 grams of ice at –18.4 ºC into steam at 126.4 ºC.?
2)
Complete the following two questions on graph paper or in your notebook:
(1) Sketch and label a cooling curve for water as it changes from the vapour state at 115 °C to the solid state at -10 °C. Assume that the water passes through all three states of matter.
(2) How much heat is absorbed in changing 2.00 kg of ice at −5.0 °C to steam at 110 °C?
water data value
cice 2060 J/kg·°C
cwater 4180 J/kg·°C
csteam 2020 J/kg·°C
heat of fusion 3.34 x 105 J/kg
heat of vaporization 2.26 x 106 J/kg
This is a six step question. You will calculate five heat quantities and then total them.
Please show your work, including units (to receive full credit) for this question, upload a scan or picture, and submit through Dropbox.
The energy required to convert 15.0 grams of ice at -18.4ºC into steam at 126.4ºC is approximately 45,737 Joules.
To convert ice at -18.4ºC into steam at 126.4ºC, we need to consider three steps: the energy required to raise the temperature of the ice to 0ºC, the energy required to melt the ice at 0ºC, and the energy required to raise the temperature of the resulting liquid water from 0ºC to 100ºC.
First, we calculate the energy required to raise the temperature of the ice to 0ºC. The mass of ice is given as 15.0 grams, and the heat capacity of ice is 2.09 J/g·ºC. Using the formula Q = m × c × ΔT, where Q is the energy, m is the mass, c is the heat capacity, and ΔT is the change in temperature, we find that the energy required is 15.0 g × 2.09 J/g·ºC × (0 ºC - (-18.4 ºC)) = 556.8 J.
Next, we calculate the energy required to melt the ice at 0 ºC. The heat of fusion for ice is 334 J/g. So the energy required is 15.0 g × 334 J/g = 5010 J.
Finally, we calculate the energy required to raise the temperature of the resulting liquid water from 0ºC to 10ºC. The heat capacity of water is 4.18 J/g·ºC. Using the same formula as before, we find that the energy required is 15.0 g × 4.18 J/g·ºC × (100ºC - 0ºC) = 6270 J.
Adding up all three steps, we get a total energy requirement of 556.8 J + 5010 J + 6270 J = 11,836.8 J.
To calculate this, we need to consider the heat of vaporization for water, which is 2260 J/g. Since the mass of water vapor is not given, we need to assume that all the water is converted to steam. Therefore, the energy required is 15.0 g × 2260 J/g = 33,900 J.
Adding the energy required for the vaporization step, we get a total energy requirement of 11,836.8 J + 33,900 J = 45,736.8 J.
Hence, the energy required to convert 15.0 grams of ice at -18.4 ºC into steam at 126.4 ºC is approximately 45,737 Joules.
To know more about energy here https://brainly.com/question/2003548
#SPJ4
The diameter of an oxygen (2) molecule is approximately 0.300 nm.
For an oxygen molecule in air at atmospheric pressure and 18.3°C, estimate the total distance traveled during a 1.00-s time interval.
The oxygen molecule is estimated to travel approximately 0.94248 nm during a 1.00-second time interval in air at atmospheric pressure and 18.3°C.
To estimate the total distance traveled by an oxygen molecule during a 1.00-second time interval,
We need to consider its average speed and the time interval.
The average speed of a molecule can be calculated using the formula:
Average speed = Distance traveled / Time interval
The distance traveled by the oxygen molecule can be approximated as the circumference of a circle with a diameter of 0.300 nm.
The formula for the circumference of a circle is:
Circumference = π * diameter
Given:
Diameter = 0.300 nm
Substituting the value into the formula:
Circumference = π * 0.300 nm
To calculate the average speed, we also need to convert the time interval into seconds.
Given that the time interval is 1.00 second, we can proceed with the calculation.
Now, we can calculate the average speed using the formula:
Average speed = Circumference / Time interval
Average speed = (π * 0.300 nm) / 1.00 s
To estimate the total distance traveled, we multiply the average speed by the time interval:
Total distance traveled = Average speed * Time interval
Total distance traveled = (π * 0.300 nm) * 1.00 s
Now, we can approximate the value using the known constant π and convert the result to a more appropriate unit:
Total distance traveled ≈ 0.94248 nm
Therefore, the oxygen molecule is estimated to travel approximately 0.94248 nm during a 1.00-second time interval in air at atmospheric pressure and 18.3°C.
Learn more about Oxygen from the given link :
https://brainly.com/question/4030823
#SPJ11
Part A What percentage of all the molecules in the glass are water? Express your answer using six significant figures. D | ΑΣΦ VO ? MAREH nwater Submit Request Answer % Assume the total number of molecules in a glass of liquid is about 1,000,000 million trillion. One million trillion of these are molecules of some poison, while 999,999 million trillion of these are water molecules.
Assuming the total number of molecules in a glass of liquid is about 1,000,000 million trillion.
One million trillion of these are molecules of some poison, while 999,999 million trillion of these are water molecules.
Express your answer using six significant figures. To determine the percentage of all the molecules in the glass that are water, we need to use the following formula: % of water = (number of water molecules/total number of molecules) × 100.
To know more about liquid visit:
https://brainly.com/question/20922015
#SPJ11