Answer:
The voltage input to the inverting terminal is 60μV
Explanation:
Given;
open-loop gain, A = 150,000
output voltage, V₀ = 15 V
voltage at the inverting input, [tex]V_n[/tex] = −40 μV = 40 x 10⁻⁶ V
The relationship between output voltage and voltage at the inverting input is given as;
[tex]V_o = A(V_p -V_n)\\\\15 = 150,000(V_p -(-40*10^{-6}))\\\\15 = 150,000 (V_p +40*10^{-6}) \\\\V_p +40*10^{-6} = \frac{15}{150,000} \\\\V_p + 40*10^{-6} = 1 *10^{-4}\\\\V_p + 40*10^{-6} = 100 *10^{-6}\\\\V_p = 100 *10^{-6} - 40*10^{-6}\\\\V_p = 60 *10^{-6}\\\\V_p = 60 \ \mu V[/tex]
Therefore, the voltage input to the inverting terminal is 60μV
is used to determine the shear stress at point P over the section supporting a downward shear force in the -y direction. What is Q
Answer:
Transverse shear stress formula
Explanation:
Transverse shear stress also known as the beam shear, is the shear stress due to bending of a beam.
Generally, when a beam is made to undergo a non-uniform bending, both bending moment (I) and a shear force (V) acts on its cross section or width (t).
Transverse shear stress formula is used to determine the shear stress at point P over the section supporting a downward shear force in the -y direction.
Mathematically, the transverse shear stress is given by the formula below;
[tex]T' = \frac{VQ}{It}[/tex]
Also note, T' is pronounced as tau.
Where;
V is the total shear force with the unit, Newton (N).
I is the Moment of Inertia of the entire cross sectional area with the unit, meters square (m²).
t is the thickness or width of cross sectional area of the material perpendicular to the shear with the unit centimeters (cm).
Q is the statical moment of area.
Mathematically, Q is given by the formula;
[tex]Q = y'P^{*} = ∑y'P^{*}[/tex]
Where [tex]P^{*}[/tex] is the section supporting a downward shear force in the y' direction.
Solid solution strengthening is achieved byGroup of answer choicesstrain hardening restricting the dislocation motion increasing the dislocation motion increasing the grain boundary g
Answer:
B. restricting the dislocation motion
Explanation:
Solid solution strengthening is a type of alloying that is carried out by the addition of the atoms of the element used for the alloying to the crystallized lattice structure of the base metal, which the metal that would be strengthened. The purpose of this act is to increase the strength of metals. It actually works by impeding or restricting the motion in the crystal lattice structure of metals thus making them more difficult to deform.
The solute atoms used for strengthening could be interstitial or substitutional. The interstitial solute atoms work by moving in between the space in the atoms of the base metal while the substitutional solute atoms make a replacement with the solvent atoms in the base metal.
Calculate the camacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in problem Neglect the effect of the earth plane.
Answer:
The answer is given below
Explanation:
A 60 Hz three-phase, three-wire overhead line has solid cylindrical conductors arranged in the form of an equilateral triangle with 4 ft conductor spacing. Conductor diameter is 0.5 in.
Given that:
The spacing between the conductors (D) = 4 ft
1 ft = 0.3048 m
D = 4 ft = 4 × 0.3048 m = 1.2192 m
The conductor diameter = 0.5 in
Radius of conductor (r) = 0.5/2 = 0.25 in = 0.00635 m
Frequency (f) = 60 Hz
The capacitance-to-neutral is given by:
[tex]C_n=\frac{2\pi \epsilon_0}{ln(\frac{D}{r} )} =\frac{2\pi *8.854*10^{-12}}{ln(1.2192/0.00635)}=1.058*10^{-11}\ F/m[/tex]
The admittance-to-neutral is given by:
[tex]Y_n=j2\pi fC_n=j*2\pi *60*1.058*10^{-11}*\frac{1000\ m}{1\ km}=j3.989*10^{-6}\ S/km[/tex]
Before you attempt to change a tire yourself, you should _____.
A. put on a pair of gloves
B. read your vehicle owner's manual for any special directions or warnings.
C. always call for emergency assistance first
D. let the remaining air out of the flat tire
Answer: read your vehicle owner's manual for any special directions or warnings.
Answer:
B. read your vehicle owner's manual for any special directions or warnings.
Explanation:
Which of the following reduces friction in an engine A)wear B)drag C)motor oil D)defractionation
It is motor oil, as oil is used to reduce friction
. The job of applications engineer for which Maria was applying requires (a) excellent technical skills with respect to mechanical engineering, (b) a commitment to working in the area of pollution control, (c) the ability to deal well and confidently with customers who have engineering problems, (d) a willingness to travel worldwide, and (e) a very intelligent and well-balanced personality. List 10 questions you would ask when interviewing applicants for the job.
Answer:
Tell us about your self Are your confident that you are the right candidate for this positionwhy should i hire youDo you like working under supervisionHow do you like to work ( in a group or individually )What is your ultimate workplace goalwhat are your future plansWhat do you expect from the Organization when given the jobDo you like taking on critical problemsHow long can you work in this positionExplanation:
For a job of applications engineer which require excellent technical skills, commitment to working , ability to deal well and confidently with customers a willingness to travel and very intelligent and well-balanced personality.
The ten questions you should ask Maria to determine if she is qualified for the job are :
Tell us about your self ( functions you have )Are your confident that you are the right candidate for this positionwhy should i hire youDo you like working under supervisionHow do you like to work ( in a group or individually )What is your ultimate workplace goalwhat are your future plansWhat do you expect from the Organization when given the jobDo you like taking on critical problemsHow long can you work in this positionwhy is the peak value of the rectified output less than the peak value of the ac input and by how much g
Answer:
The Peak value of the output voltage is less or lower than that of the peak value of the input voltage by 0.6V reason been that the voltage is tend to drop across the diode.
Explanation:
This is what we called HALF WAVE RECTIFIER in which the Peak value of the output voltage is less or lower than that of the peak value of the input voltage by 0.6V reason been that the voltage is tend to drop across the diode.
Therefore this is the formula for Half wave rectifier
Vrms = Vm/2 and Vdc
= Vm/π:
Where,
Vrms = rms value of input
Vdc = Average value of input
Vm = peak value of output
Hence, half wave rectifier is a rectifier which allows one half-cycle of an AC voltage waveform to pass which inturn block the other half-cycle which is why this type of rectifiers are often been used to help convert AC voltage to a DC voltage, because they only require a single diode to inorder to construct.
The temperature of water is 45 what does the measurement represent
Answer:
degree of hotness of coldness of a substance
A long corridor has a single light bulb and two doors with light switch at each door. design logic circuit for the light; assume that the light is off when both switches are in the same position.
Answer and Explanation:
Let A denote its switch first after that we will assume B which denotes the next switch and then we will assume C stand for both the bulb. we assume 0 mean turn off while 1 mean turn on, too. The light is off, as both switches are in the same place. This may be illustrated with the below table of truth:
A B C (output)
0 0 0
0 1 1
1 0 1
1 1 0
The logic circuit is shown below
C = A'B + AB'
If the switches are in multiple places the bulb outcome will be on on the other hand if another switches are all in the same place, the result of the bulb will be off. This gate is XOR. The gate is shown in the diagram adjoining below.
Liquidated damages are intended to represent anticipated losses to the owner based upon circumstances existing at the time the contract was made. List at least five types of potential losses to the owner that would qualify for determination of such potential losses.
Answer:
1. Loss of income.
2. Rental costs.
3. Utility bills.
4. Loss of rent.
5. Storage costs.
Explanation:
Liquidated damages can be defined as pre-determined damages or clauses that are highlighted or indicated at the time of entering into a contract between a contractor and a client which is mainly based on evaluation of the actual loss the client may incur should the contractor fail to meet the agreed completion date.
Generally, liquidated damages are meant to be fair rather than being a penalty or punitive to the defaulter. It is usually calculated on a daily basis for the loss.
When entering into a contract with another, liquidated damages are intended to represent anticipated losses to the owner based upon circumstances existing at the time the contract was made.
Listed below are five (5) types of potential losses to the owner that would qualify for determination of such potential losses;
1. Loss of income.
2. Rental costs.
3. Utility bills.
4. Loss of rent.
5. Storage costs.
For a fluid flowing through a pipe assuming that pressure drop per unit length of pipe (P/L) depends on the diameter of the pipe , the velocity of fluid, the density of fluid and the viscosity of the fluid. Show that = ∅ ൬ ൰
Answer:
Explanation:
La vaca
El pato
Air enters the compressor of an ideal cold air-standard Brayton cycle at 100 kPa, 300 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10, and the turbine inlet temperature is 1400 K. For k 5 1.4, calculate (a) the thermal efficiency of the cycle. (b) the back work ratio. (c) the net power developed, in kW.
Answer:
(a) 48.2 %
(b) 0.4137
(c) 2385.9 kW
Explanation:
The given values are:
Initial pressure,
p₁ = 100 kPa
Initial temperature,
T₁ = 300 K
Mass,
M = 6 kg/s
Pressure ration,
r = 10
Inlent temperature,
T₃ = 1400 K
Specific heat ratio,
k = 1.4
At T₁ and p₁,
⇒ [tex]c_{p}=1.005 \ KJ/Kg.K[/tex]
Process 1-2 in isentropic compression, we get
⇒ [tex]\frac{T_{2}}{T_{1}}=(\frac{p_{2}}{p_{1}})^{\frac{k-1}{k}}[/tex]
[tex]T_{2}=(\frac{p_{2}}{p_{1}})^{\frac{k-1}{k}}. T_{1}[/tex]
On putting the estimated values, we get
[tex]=(10)^{\frac{1.4-1}{1.4}}(300)[/tex]
[tex]=579.2 \ K[/tex]
Process 3-4,
⇒ [tex]\frac{T_{4}}{T_{3}}=(\frac{p_{4}}{p_{3}})^{\frac{k-1}{k}}[/tex]
[tex]T_{4}=(\frac{1}{10})^{\frac{1.4-1}{1.4}}(1400)[/tex]
[tex]=725.13 \ K[/tex]
(a)...
The thermal efficiency will be:
⇒ [tex]\eta =\frac{\dot{W_{t}}-\dot{W_{e}}}{\dot{Q_{in}}}[/tex]
[tex]\eta=1-\frac{\dot{Q_{out}}}{\dot{Q_{in}}}[/tex]
⇒ [tex]\dot{Q_{in}}=\dot{m}(h_{1}-h_{2})[/tex]
[tex]=\dot{mc_{p}}(T_{3}-T_{2})[/tex]
[tex]=6\times 1005\times (1400-579.2)[/tex]
[tex]=4949.4 \ kJ/s[/tex]
⇒ [tex]\dot{Q_{out}}=\dot{m}(h_{4}-h_{1})[/tex]
[tex]=6\times 1.005\times (725.13-300)[/tex]
[tex]=2563.5 \ KJ/S[/tex]
As we know,
⇒ [tex]\eta=1-\frac{\dot{Q_{out}}}{\dot{Q_{in}}}[/tex]
On putting the values, we get
[tex]=1-\frac{2563.5}{4949.4}[/tex]
[tex]=0.482 \ i.e., \ 48.2 \ Percent[/tex]
(b)...
Back work ratio will be:
⇒ [tex]bwr=\frac{\dot{W_{e}}}{\dot{W_{t}}}[/tex]
Now,
⇒ [tex]\dot{W_{e}}=\dot{mc_{p}}(T_{2}-T_{1})[/tex]
On putting values, we get
[tex]=6\times 1.005\times (579.2-300)[/tex]
[tex]=1683.6 \ kJ/s[/tex]
⇒ [tex]\dot{W_{t}}=\dot{mc_{p}}(T_{3}-T_{4})[/tex]
[tex]=6\times 1.005\times (1400-725.13)[/tex]
[tex]=4069.5 \ kJ/s[/tex]
So that,
⇒ [tex]bwr=\frac{1683.6}{4069.5}=0.4137[/tex]
(c)...
Net power is equivalent to,
⇒ [tex]\dot{W}_{eyele}=\dot{W_{t}}-\dot{W_{e}}[/tex]
On substituting the values, we get
[tex]= 4069.5-1683.6[/tex]
[tex]=2385.9 \ kW[/tex]
Following are the solution to the given points:
Given :
Initial pressure [tex]p_1 = 100\ kPa \\\\[/tex]
Initial temperature [tex]T_1 = 300\ K \\\\[/tex]
Mass flow rate of air [tex]m= 6\ \frac{kg}{s}\\\\[/tex]
Compressor pressure ratio [tex]r =10\\\\[/tex]
Turbine inlet temperature [tex]T_3 = 1400\ K\\\\[/tex]
Specific heat ratio [tex]k=1.4\\\\[/tex]
Temperature [tex]\ T_1 = 300\ K[/tex]
pressure [tex]p_1 = 100\ kPa\\\\[/tex]
[tex]\to c_p=1.005\ \frac{kJ}{kg\cdot K}\\\\[/tex]
Process 1-2 is isen tropic compression
[tex]\to \frac{T_2}{T_1}=(\frac{P_2}{P_1})^{\frac{k-1}{k}} \\\\[/tex]
[tex]\to T_2=(\frac{P_2}{P_1})^{\frac{k-1}{k}} \ T_1 \\\\[/tex]
[tex]=(10)^{\frac{1.4-1}{1.4}} (300)\\\\ =(10)^{\frac{0.4}{1.4}} (300) \\\\[/tex]
[tex]\to T_2 = 579.2\ K \\\\[/tex]
Process 3-4 is isen tropic expansion
[tex]\to \frac{T_4}{T_3}=(\frac{P_4}{P_3})^{\frac{k-1}{k}}\\\\ \to T_4=(\frac{1}{10})^{\frac{1.4-1}{1.4}} (1400)\\\\\to T_4= 725.13\ K \\\\[/tex]
For point a:
The thermal efficiency of the cycle:
[tex]\to \eta = \frac{W_i-W_e}{Q_{in}} \\\\\to \eta = \frac{Q_{in}- Q_{out}}{Q_{in}}\\\\\to \eta =1 - \frac{Q_{out}}{Q_{in}} \\\\\to Q_{in}= m(h_3-h_1) = mc_p (T_4-T_1) =(6)(1.005)(725.13-300) = 2563 \ \frac{kJ}{S}\\\\\to \eta =1- \frac{Q_{out}}{Q_{in}}\\\\[/tex]
[tex]=1-\frac{2563.5}{4949.4}\\\\ = 0.482\\\\[/tex]
[tex]\eta = 48.2\%\\\\[/tex]
For point b:
The back work ratio
[tex]\to bwr =\frac{W_e}{W_t}[/tex]
Now
[tex]\to W_e =mc_p (T_2 -T_1)[/tex]
[tex]=(6) (1.005)(579.2 -300)\\\\ =1683.6 \ \frac{kJ}{S}\\\\[/tex]
[tex]\to W_t=mc_p(T_3-T_4)[/tex]
[tex]=(6)(1.005)(1400 - 725.13)\\\\ = 4069.5 \frac{KJ}{s}[/tex]
[tex]\to bwr =\frac{W_s}{W_t}= \frac{1683.6}{4069.5}=0.4137[/tex]
For point c:
The net power developed is equal to
[tex]\to W_{cycle} = W_t-W_e \\\\[/tex]
[tex]= ( 4069.5-1683.6)\\\\ = 2385.9 \ kW\\[/tex]
Learn more about Air compressors:
brainly.com/question/15181914
For each of the following stacking sequences found in FCC metals, cite the type of planar defect that exists:
a. . . . A B C A B C B A C B A . . .
b. . . . A B C A B C B C A B C . . .
Copy the stacking sequences and indicate the position(s) of planar defect(s) with a vertical dashed line.
Answer:
a) The planar defect that exists is twin boundary defect.
b) The planar defect that exists is the stacking fault.
Explanation:
I am using bold and underline instead of a vertical line.
a. A B C A B C B A C B A
In this stacking sequence, the planar defect that occurs is twin boundary defect because the stacking sequence at one side of the bold and underlined part of the sequence is the mirror image or reflection of the stacking sequence on the other side. This shows twinning. Hence it is the twin boundary inter facial defect.
b. A B C A B C B C A B C
In this stacking sequence the planar defect that occurs is which occurs is stacking fault defect. This underlined region is HCP like sequence. Here BC is the extra plane hence resulting in the stacking fault defect. The fcc stacking sequence with no defects should be A B C A B C A B C A B C. So in the above stacking sequence we can see that A is missing in the sequence. Instead BC is the defect or extra plane. So this disordering of the sequence results in stacking fault defect.
One kg of an idea gas is contained in one side of a well-insulated vessel at 800 kPa. The other side of the vessel is under vacuum. The two sides are separated by a piston that is initially held in place by the pins. The pins are removed and the gas suddenly expands until it hits the stops. What happens to the internal energy of the gas?
a. internal energy goes up
b. internal energy goes down
c. internal energy stays the same
d. we need to know the volumes to make the calculation
Answer:
Option C = internal energy stays the same.
Explanation:
The internal energy will remain the same or unchanged because this question has to do with a concept in physics or classical chemistry (in thermodynamics) known as Free expansion.
So, the internal energy will be equals to the multiplication of the change in temperature, the heat capacity (keeping volume constant) and the number of moles. And in free expansion the internal energy is ZERO/UNCHANGED.
Where, the internal energy, ∆U = 0 =quantity of heat, q - work,w.
The amount of heat,q = Work,w.
In the concept of free expansion the only thing that changes is the volume.
Identify the advantages of using 6 tube passes instead of just 2 of the same diameter in shell-and-tube heat exchanger.What are the advantages and disadvantages of using 6 tube passes instead of just 2 of the same diameter?
Answer:
Please check explanation for answer
Explanation:
Here, we are concerned with stating the advantages and disadvantages of using a 6 tube passes instead of a 2 tube passes of the same diameter:
Advantages
* By using a 6 tube passes diameter, we are increasing the surface area of the heat transfer surface
* As a result of increasing the heat transfer surface area, the rate of heat transfer automatically increases too
Thus, from the above, we can conclude that the heat transfer rate of a 6 tube passes is higher than that of a 2 tube passes of the same diameter.
Disadvantages
* They are larger in size and in weight when compared to a 2 tube passes of the same diameter and therefore does not find use in applications where space conservation is quite necessary.
* They are more expensive than the 2 tube passes of the same diameter and thus are primarily undesirable in terms of manufacturing costs
After impact testing a sample at -100oC you realize that the fracture surface is very dull and fibrous. Is the sample behaving in a ductile of brittle manner at this temperature
Answer:
Ductile
Explanation:
So, from the question, we have the following information or parameters or data which is going to help us in solving this particular problem or question;
=> " impact testing a sample = -100oC shows that the fracture surface is very DULL AND FIBROUS"
TAKE NOTE: DULL AND FIBROUS.
IMPACT TESTING is used by engineers in the configuration of a sample or object.
In order to determine whether a specimen is ductile or brittle, it can be shown from its appearance for instance;
A DUCTILE SAMPLE will be DULL AND FIBROUS thus, our answer!
But a brittle sample will have a crystal shape.
A shaft made of aluminum is 40.0 mm in diameter at room temperature (21°C). Its coefficient of thermal expansion = 24.8 x 10-6 mm/mm per °C. If it must be reduced in size by 0.20 mm in order to be expansion fitted into a hole, determine the temperature to which the shaft must be cooled.
Answer:
Temperature to which the shaft must be cooled, [tex]\theta_2 = -180.61 ^0C[/tex]
Explanation:
Diameter of the shaft at room temperature, d₁ = 40 mm
Room temperature, θ₁ = 21°C
Coefficient of thermal expansion, [tex]\alpha = 24.8 * 10^{-6} / ^0 C[/tex]
The shaft is reduced in size by 0.20 mm:
Δd = - 0.20 mm
The temperature to which the shaft must be cooled, θ₂ = ?
The coefficient of thermal expansion is given by the equation:
[tex]\alpha = \frac{\triangle d}{d_1 * \triangle \theta}\\\\24.8 * 10^{-6} = \frac{-0.20}{40 * \triangle \theta}\\\\\triangle \theta = \frac{-0.20 }{24.8 * 10^{-6} * 40} \\\\\triangle \theta = - 201.61 ^0 C\\\triangle \theta = \theta_2 - \theta_1\\\\- 201.61 = \theta_2 - 21\\\\\theta_2 = -201.61 + 21\\\\\theta_2 = -180.61 ^0C[/tex]
For a bolted assembly with six bolts, the stiffness of each bolt is kb=Mlbf/in and the stiffness of the members is km=12Mlbf/in. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in- 13 UNC grade 8 bolts with rolled threads. Assume the bolts are preloaded to 75% of the proof load. Clearly state any assumptions.
(a) Determine the yielding factor of safety,
(b) Determine the overload factor of safety,
(c) Determine the factor of safety baserd on joint seperation.
Answer:
nP ≈ 4.9 nL = 1.50Explanation:
GIVEN DATA
external load applied (p) = 85 kips
bolt stiffness ( Kb ) = 3(10^6) Ibf / in
Member stiffness (Km) = 12(10^6) Ibf / in
Diameter of bolts ( d ) = 1/2 in - 13 UNC grade 8
Number of bolts = 6
assumptions
for unified screw threads UNC and UNF
tensile stress area ( A ) = 0.1419 in^2
SAE specifications for steel bolts for grade 8
we have
Minimum proff strength ( Sp) = 120 kpsi
Minimum tensile strength (St) = 150 Kpsi
Load Bolt (p) = external load / number of bolts = 85 / 6 = 14.17 kips
Given the following values
Fi = 75%* Sp*At = (0.75*120*0.1419 ) = 12.771 kip
Preload stress
αi = 0.75Sp = 0.75 * 120 = 90 kpsi
stiffness constant
C = [tex]\frac{Kb}{Kb + Km}[/tex] = [tex]\frac{3}{3+2}[/tex] = 0.2
A) yielding factor of safety
nP = [tex]\frac{sPAt}{Cp + Fi}[/tex] = [tex]\frac{120* 0.1419}{0.2*14.17 + 12.771}[/tex]
nP = 77.028 / 15.605 = 4.94 ≈ 4.9
B) Determine the overload factor safety
[tex]nL = \frac{SpAt - Fi}{CP}[/tex] = ( 120 * 0.1419) - 12.771 / 0.2 * 14.17
= 17.028 - 12.771 / 2.834
= 1.50
By saying that the electrostatic field is conservative, we do not mean that:_______ The potential difference between any two points is zero. It is the gradient of scalar potential. Its circulation is identically zero along any path. Its curl is identically zero everywhere. The work done in moving a charge along closed path inside the field is zero.
Answer:
(a) The potential difference between any two points is zero.
Explanation:
A conservative field is;
i. a vector field that is the gradient of some function. Electrostatic field is the gradient of scalar potential, hence it is conservative.
ii. a vector field where the integral along every closed path is zero. This means that the work done in a closed cycle is zero. For an electrostatic field, the charge along closed path inside the field is zero. Hence, electrostatic field is conservative.
iii. a vector field if curl of its potential(vector product of the del operator and the potential) is zero. The curl of electrostatic field is identically zero everywhere.
iv. a vector field whose circulation is zero along any path.
v. a vector field whose potential difference between two points is independent of the path taken. The potential difference between any two points is not necessarily zero.
Other examples of conservative fields are;
i. gravitational field.
ii. magnetic field.
When we say that electrostatic field is conservative, we do not mean that the potential difference between any two points is zero.
What is a conservative field?A conservative field refers to a form of force between the Earth and another mass whose work is determined only by the final displacement of the object acted upon.
What we mean by saying an electrostatic field is conservative includes:
It is the gradient of scalar potentialIts circulation is identically zero along any pathIts curl is identically zero everywhereThe work done in moving a charge along closed path inside the field is zero.Hence, when we say that electrostatic field is conservative, we do not mean that the potential difference between any two points is zero.
Therefore, the Option A is correct.
Read more about conservative field
brainly.com/question/10712927
The value of an SMT capacitor is signified by a
Answer:
Working volttage
Explanation:
SMT electrolytic capacitors are marked with working voltage. The value of these capacitors is measured in micro farads. It is a surface mount capacitor which is used for high volume manufacturers. They are small lead less and are widely used. They are placed on modern circuit boards.
A 15.00 mL sample of a solution of H2SO4 of unknown concentration was titrated with 0.3200M NaOH. the titration required 21.30 mL of the base. Assuming complete neutralization of the acid,
1) What was the normality of the acid solution?
2) What was the molarity of the acid solution?
Answer:
a. 0.4544 N
b. [tex]5.112 \times 10^{-5 M}[/tex]
Explanation:
For computing the normality and molarity of the acid solution first we need to do the following calculations
The balanced reaction
[tex]H_2SO_4 + 2NaOH = Na_2SO_4 + 2H_2O[/tex]
[tex]NaOH\ Mass = Normality \times equivalent\ weight \times\ volume[/tex]
[tex]= 0.3200 \times 40 g \times 21.30 mL \times 1L/1000mL[/tex]
= 0.27264 g
[tex]NaOH\ mass = \frac{mass}{molecular\ weight}[/tex]
[tex]= \frac{0.27264\ g}{40g/mol}[/tex]
= 0.006816 mol
Now
Moles of [tex]H_2SO_4[/tex] needed is
[tex]= \frac{0.006816}{2}[/tex]
= 0.003408 mol
[tex]Mass\ of\ H_2SO_4 = moles \times molecular\ weight[/tex]
[tex]= 0.003408\ mol \times 98g/mol[/tex]
= 0.333984 g
Now based on the above calculation
a. Normality of acid is
[tex]= \frac{acid\ mass}{equivalent\ weight \times volume}[/tex]
[tex]= \frac{0.333984 g}{49 \times 0.015}[/tex]
= 0.4544 N
b. And, the acid solution molarity is
[tex]= \frac{moles}{Volume}[/tex]
[tex]= \frac{0.003408 mol}{15\ mL \times 1L/1000\ mL}[/tex]
= 0.00005112
=[tex]5.112 \times 10^{-5 M}[/tex]
We simply applied the above formulas
The volume of the 0.3200 M, NaOH required to neutralize the H₂SO₄, is
21.30 mL, which gives the following acid solution approximate values;
1) Normality of the acid solution is 0.4544 N
2) The molarity of the acid is 0.2272
How can the normality, molarity of the solution be found?Molarity of the NaOH = 0.3200 M
Volume of NaOH required = 21.30 mL
1) The normality of the acid solution is found as follows;
The chemical reaction is presented as follows;
H₂SO₄(aq) + 2NaOH (aq) → Na₂SO₄ (aq) + H₂O
Number of moles of NaOH in the reaction is found as follows;
[tex]n = \dfrac{21.30}{1,000} \times 0.3200 \, M = \mathbf{0.006816 \, M}[/tex]
Therefore;
The number of moles of H₂SO₄ = 0.006816 M ÷ 2 = 0.003408 M
[tex]Normality = \mathbf{ \dfrac{Mass \ of \, Acid \ in \ reaction}{Equivalent \ mass \times Volume \ of \ soltute}}[/tex]
Which gives;
[tex]Normality = \dfrac{ 98 \times 0.003408 }{49 \times 0.015} = \mathbf{0.4544}[/tex]
The normality of the acid solution, H₂SO₄(aq), N ≈ 0.45442) The molarity is found as follows;
[tex]Molarity = \dfrac{0.003408 \, moles}{0.015 \, L} = \mathbf{0.2272 \, M}[/tex]
The molarity of the acid solution is 0.2272 MLearn more about the normality and the molarity of a solution here:
https://brainly.com/question/6532653
https://brainly.com/question/14112872
1. The sine rule is used when we are given either a) two angles and one side, or b) two sides and a non-included angle.
i. True
ii. False
2. The cosine rule is used when we are given either a) three sides or b) two sides and the included angle.
i. True
ii. False
Answer:
A. Yes
B. Yes
Explanation:
We want to evaluate the validity of the given assertions.
1. The first statement is true
The sine rule stipulates that the ratio of a side and the sine of the angle facing the side is a constant for all sides of the triangle.
Hence, to use it, it’s either we have two sides and an angle and we are tasked with calculating the value of the non given side
Or
We have two angles and a side and we want to calculate the value of the side provided we have the angle facing this side in question.
For notation purposes;
We can express the it for a triangle having three sides a, b, c and angles A,B, C with each lower case letter being the side that faces its corresponding big letter angles
a/Sin A = b/Sin B = c/Sin C
2. The cosine rule looks like the Pythagoras’s theorem in notation but has a subtraction extension that multiplies two times the product of the other two sides and the cosine of the angle facing the side we want to calculate
So let’s say we want to calculate the side a in a triangle of sides a, b , c and we have the angle facing the side A
That would be;
a^2 = b^2 + c^2 -2bcCosA
So yes, the cosine rule can be used for the scenario above
Air enters the first compressor stage of a cold-air standard Brayton cycle with regeneration and intercooling at 100 kPa, 300 K, with a mass flow rate of 6 kg/s. The overall compressor pressure ratio is 10, and the pressure ratios are the same across each compressor stage. The temperature at the inlet to the second compressor stage is 300 K. The turbine inlet temperature is 1400 K. The compressor stages and turbine each have isentropic efficiencies of 80% and the regenerator effectiveness is 80%. For k = 1.4, calculate:
a. the thermal efficiency of the cycle
b. the back work ratio
c. the net power developed, in kW
d. the rates of exergy destruction in each compressor stage and the turbine stage as well as the regenerator, in kW, for T 0 = 300 K.
Answer:
a. [tex]\eta _{th}[/tex] = 77.65%
b. bwr = 6.5%
c. 3538.986 kW
d. -163.169 kJ
Explanation:
a. The given property are;
P₂/P₁ = 10, P₂ = 10 * 100 kPa = 1000 kPa
p₄/p₁ = 10
P₂/P₁ = p₄/p₃ = √10
p₂ = 100·√10
[tex]T_{2s}[/tex] = T₁×(√10)^(0.4/1.4) = 300 × (√10)^(0.4/1.4) = 416.85 K
T₂ = T₁ + ([tex]T_{2s}[/tex] - T₁)/[tex]\eta _c[/tex] = 300 + (416.85 - 300)/0.8 = 446.0625 K
p₄ = 10×p₁ = 10×100 = 1000 kPa
p₄/p₃ = √10 =
p₃ = 100·√10
T₃ = 300 K
T₃/[tex]T_{4s}[/tex] = (P₂/P₁)^((k - 1)/k) = (√10)^(0.4/1.4)
[tex]T_{4s}[/tex] = T₃/((√10)^(0.4/1.4) ) = 300/((√10)^(0.4/1.4)) = 215.905 K
T₄ = T₃ + ([tex]T_{4s}[/tex] - T₃)/[tex]\eta _c[/tex] = 300 + (215.905- 300)/0.8 = 194.881 K
The efficiency = 1 - (T₄ - T₁)/(T₃ - T₂) = 1 - (194.881 -300)/(300 -446.0625 ) = 0.28
T₄ = 446.0625 K
T₆ = 1400 K
[tex]T_{7s}[/tex]/T₆ = (1/√10)^(0.4/1.4)
[tex]T_{7s}[/tex] = 1400×(1/√10)^(0.4/1.4) = 1007.6 K
T₇ = T₆ - [tex]\eta _t[/tex](T₆ - [tex]T_{7s}[/tex]) = 1400 - 0.8*(1400 - 1007.6) = 1086.08 K
T₈ = 1400 K
T₉ = 1086.08 K
T₅ = T₄ + [tex]\epsilon _{regen}[/tex](T₉ - T₄) = 446.0625 +0.8*(1086.08 - 446.0625) = 958.0765 K
[tex]\eta _{th}[/tex] =(((T₆ - T₇) + (T₈ - T₉)) -((T₂ - T₁) + (T₄ - T₃)))/((T₆ - T₅) + (T₈ - T₇))
(((1400 - 1086.08) + (1400 -1086.08 ))-((446.0625 - 300)+(194.881 - 300)))/((1400 -958.0765 ) + (1400 -1086.08 )) = 0.7765
[tex]\eta _{th}[/tex] = 77.65%
b. Back work ratio, bwr = [tex]bwr = \dfrac{w_{c,in}}{w_{t,out}}[/tex]
((446.0625 - 300)+(194.881 - 300))/((1400 - 1086.08) + (1400 -1086.08 ))
40.9435/627.84 = 6.5%
c. [tex]w_{net, out} = c_p[(T_6 -T_7) + (T_8 - T_9)] - [(T_2 - T_1) + (T_4 -T_3)][/tex]
Power developed is given by the relation;
[tex]\dot m \cdot w_{net, out}[/tex]
[tex]\dot m \cdot w_{net, out}[/tex]= 6*1.005*(((1400 - 1086.08) + (1400 -1086.08 ))-((446.0625 - 300)+(194.881 - 300))) = 3538.986 kW
d. Exergy destruction = 6*(1.005*(300-446.0625 ) - 300*1.005*(-0.3966766)
-163.169 kJ
When the value of the output cannot be determined even if the value of the controllable input is known, the model is:_________
a. analog.
b. digital.
c. stochastic.
d. deterministic.
Answer:
c. stochastic.
Explanation:
A stochastic model is a tool in statistics, used to estimate the probability distributions of intended outcomes by the allowance of random variation in any number of the inputs over time. For a stochastic model, Inputs to a quantitative model are uncertain, and the value of the output from a stochastic model cannot be easily determined, even if the value of the input that can be determined is known. The distributions of the resulting outcomes of a stochastic model is usually due to the large number of simulations involved, and it is widely used as a statistical tool in the life sciences.
A ramp from an expressway with a design speed of 30 mi/h connects with a local road, forming a T intersection. An additional lane is provided on the local road to allow vehicles from the ramp to turn right onto the local road without stopping. The turning roadway has stabilized shoulders on both sides and will provide for a onelane, one-way operation with no provision for passing a stalled vehicle. Determine the width of the turning roadway if the design vehicle is a single-unit truck. Use 0.08 for superelevation.
Answer:
the width of the turning roadway = 15 ft
Explanation:
Given that:
A ramp from an expressway with a design speed(u) = 30 mi/h connects with a local road
Using 0.08 for superelevation(e)
The minimum radius of the curve on the road can be determined by using the expression:
[tex]R = \dfrac{u^2}{15(e+f_s)}[/tex]
where;
R= radius
[tex]f_s[/tex] = coefficient of friction
From the tables of coefficient of friction for a design speed at 30 mi/h ;
[tex]f_s[/tex] = 0.20
So;
[tex]R = \dfrac{30^2}{15(0.08+0.20)}[/tex]
[tex]R = \dfrac{900}{15(0.28)}[/tex]
[tex]R = \dfrac{900}{4.2}[/tex]
R = 214.29 ft
R ≅ 215 ft
However; given that :
The turning roadway has stabilized shoulders on both sides and will provide for a onelane, one-way operation with no provision for passing a stalled vehicle.
From the tables of "Design widths of pavement for turning roads"
For a One-way operation with no provision for passing a stalled vehicle; this criteria falls under Case 1 operation
Similarly; we are told that the design vehicle is a single-unit truck; so therefore , it falls under traffic condition B.
As such in Case 1 operation that falls under traffic condition B in accordance with the Design widths of pavement for turning roads;
If the radius = 215 ft; the value for the width of the turning roadway for this conditions = 15ft
Hence; the width of the turning roadway = 15 ft
I2 + KOH = KIO3 + KI + H2O Marque la(s) respuesta(s) falsas: La suma de coeficientes mínimos del agua y el agente reductor es 6 El KI es la forma reducida El KOH es el agente reductor La suma de electrones transferidos más el coeficiente mínimo del agua suman 16 La relación entre el agente oxidante y el agente reductor es 1
Answer:
Las declaraciones falsas incluyen
- El KOH es el agente reductor.
- La suma de electrones transferidos más el coeficiente mínimo de agua suman 16.
Todas las otras declaraciones son ciertas.
The false statements include
- The KOH is the reducing agent.
- The sum of transferred electrons plus the minimum coefficient of water add up to 16.
All the other statements are true.
Explanation:
Es evidente que esta es una reacción redox en presencia de medio básico. Entonces, equilibraremos esta reacción redox en pasos. I₂ + KOH → KIO₃ + KI + H₂O
Paso 1 Eliminar los iones espectadores; Estos son los iones que aparecen en ambos lados de la reacción. Es evidente que solo el ion de potasio (K⁺) es el ion espectador de esta reacción.
I₂ + OH⁻ → IO₃⁻ + I⁻ + H₂O
Paso 2
Separamos la reacción en las medias reacciones de oxidación y reductina. La oxidación es la pérdida de electrones que conduce a un aumento del número de oxidación del ion, mientras que la reducción es la ganancia de elecrones que conduce a una disminución en el número de oxidación del ion. También es evidente que es el gas de yodo el que se reduce y oxida para esta reacción.
El gas de yodo se reduce a I⁻ (el número de oxidación se reduce de 0 a -1) y el gas de yodo se oxida a IO₃⁻ (el número de oxidación de yodo aumenta de 0 en gas de yodo a +5 en IO₃⁻)
Reducción media reacción
I₂ → I⁻
Media reacción de oxidación
I₂ + OH⁻ → IO₃⁻ + H₂O
Paso 3
Equilibramos las medias reacciones y agregamos los respectivos electrones transferidos
Reducción media reacción
I₂ → 2I⁻
I₂ + 2e⁻ → 2I⁻
Media reacción de oxidación
I₂ + 12OH⁻ → 2IO₃⁻ + 6H₂O
I₂ + 12OH⁻ → 2IO₃⁻ + 6H₂O + 10e⁻
Paso 4
Balancee el número de electrones en las dos medias reacciones
[I₂ + 2e⁻ → 2I⁻] × 5
[I₂ + 12OH⁻ → 2IO₃⁻ + 6H₂O + 10e⁻] × 1
5I₂ + 10e⁻ → 10I⁻
I₂ + 12OH⁻ → 2IO₃⁻ + 6H₂O + 10e⁻
Paso 5
Agregue las dos medias reacciones y elimine cualquier especie que aparezca en ambos lados
5I₂ + 10e⁻ + I₂ + 12OH⁻ → 10I⁻ + 2IO₃⁻ + 6H₂O + 10e⁻
Entonces, eliminamos los 10 electrones que fueron transferidos en la reacción balanceada
6I₂ + 12OH⁻ → 10I⁻ + 2IO₃⁻ + 6H₂O
Paso 6
Reintroducimos la especie eliminada desde el principio (el ion potasio)
6I₂ + 12KOH → 10KI + 2KIO₃ + 6H₂O
Los coeficientes mínimos son entonces
3I₂ + 6KOH → 5KI + KIO₃ + 3H₂O
Luego verificamos cada una de las declaraciones proporcionadas para elegir las falsas.
- La suma de los coeficientes mínimos del agua y el agente reductor es 6.
El gas yodo es el agente reductor y oxidante. Coeficiente mínimo de agua y gas de yodo = 3 + 3 = 6 Esta afirmación es cierta.
- El KI es la forma reductora KI resulta de la semirreacción de reducción.
Por lo tanto, es la forma reducida del gas de yodo. Esta afirmación es cierta. - El KOH es el agente reductor. KOH no es el agente reductor. Esta afirmación es falsa.
- La suma de los electrones transferidos más el coeficiente mínimo de agua suman 16.
Electrones transferidos = 10
Coeficiente mínimo de agua = 3
Suma = 13 y no 16.
Esta afirmación es falsa.
- La proporción del agente oxidante y el agente reductor es 1.
Dado que el gas yodo es el agente reductor y oxidante, la proporción de estos dos es verdaderamente 1. Esta afirmación es cierta.
¡¡¡Espero que esto ayude!!!
Determine whether or not it is possible to cold work steel so as to give a minimum Brinell hardness of 225 and at the same time have a ductility of at least 12%EL. Justify your decision
Answer:
First we determine the tensile strength using the equation;
Tₓ (MPa) = 3.45 × HB
{ Tₓ is tensile strength, HB is Brinell hardness = 225 }
therefore
Tₓ = 3.45 × 225
Tₓ = 775 Mpa
From Conclusions, It is stated that in order to achieve a tensile strength of 775 MPa for a steel, the percentage of the cold work should be 10
When the percentage of cold work for steel is up to 10,the ductility is 16% EL.
And 16% EL is greater than 12% EL
Therefore, it is possible to cold work steel to a given minimum Brinell hardness of 225 and at the same time a ductility of at least 12% EL
The closed feedwater heater of a regenerative Rankine cycle is to heat 7000 kPa feedwater from 2608C to a saturated liquid. The turbine supplies bleed steam at 6000 kPa and 3258C to this unit. This steam is condensed to a saturated liquid before entering the pump. Calculate the amount of bleed steam required to heat 1 kg of feedwater in this unit.
Answer:
the amount of bleed steam required to heat 1 kg of feedwater in this unit is 0.078 kg/s
Explanation:
Given that:
Pressure of the feed water = 7000 kPa
Temperature of the closed feedwater heater = 260 ° C
Pressure of of the turbine = 6000 kPa
Temperature of the turbine = 325 ° C
The objective is to calculate the amount of bleed steam required to heat 1 kg of feedwater in this unit.
From the table A-4 of saturated water temperature table at temperature 260° C at state 1 ;
Enthalpies:
[tex]h_1 = h_f = 1134.8 \ kJ/kg[/tex]
From table A-6 superheated water at state 3 ; the value of the enthalpy relating to the pressure of the turbine at 6000 kPa and temperature of 325° C is obtained by the interpolating the temperature between 300 ° C and 350 ° C
At 300° C; enthalpy = 2885.6 kJ/kg
At 325° C. enthalpy = 3043.9 kJ/kg
Thus;
[tex]\dfrac{325-300}{350-300}=\dfrac{h_{325^0}-{h_{300^0}}}{{h_{350^0}}- {h_{300^0}}}[/tex]
[tex]\dfrac{325-300}{350-300}=\dfrac{h_{325^0}-2885.6}{3043.9-2885.6 }}[/tex]
[tex]\dfrac{25}{50}=\dfrac{h_{325^0}-2885.6}{3043.9-2885.6 }}[/tex]
[tex]h_{325^0} = 2885.6 + \dfrac{25}{50}({3043.9-2885.6 )[/tex]
[tex]h_{325^0} = 2885.6 + 0.5({3043.9-2885.6 )[/tex]
[tex]h_{325^0} =2964.75 \ kJ/kg[/tex]
At pressure of 7000 kPa at state 6; we obtain the enthalpies corresponding to the pressure at table A-5 of the saturated water pressure tables.
[tex]h_6 = h_f = 1267.5 \ kJ/kg[/tex]
From state 4 ;we obtain the specific volume corresponding to the pressure of 6000 kPa at table A-5 of the saturated water pressure tables.
[tex]v_4 = v_f = 0.001319\ m^3 /kg[/tex]
However; the specific work pump can be determined by using the formula;
[tex]W_p = v_4 (P_5-P_4)[/tex]
where;
[tex]P_4[/tex] = pressure at state 4
[tex]P_5[/tex] = pressure at state 5
[tex]W_p = 0.001319 (7000-6000)[/tex]
[tex]W_p = 0.001319 (1000)[/tex]
[tex]W_p =1.319 \ kJ/kg[/tex]
Using the energy balance equation of the closed feedwater heater to calculate the amount of bleed steam required to heat 1 kg of feed water ; we have:
[tex]E_{in} = E_{out} \\ \\ m_1h_1 +m_3h_3 + m_3W_p = (m_1+m_3)h_6[/tex]
where;
[tex]m_1 = 1 \ kg[/tex]
Replacing our other value as derived above into the energy balance equation ; we have:
[tex]1 \times 1134.8 +m_3 \times 2964.75 + m_3 \times 1.319 = (1+m_3)\times 1267.5[/tex]
[tex]1134.8 + 2966.069 \ m_3 = 1267.5 + 1267.5m_3[/tex]
Collect like terms
[tex]2966.069 \ m_3- 1267.5m_3 = 1267.5-1134.8[/tex]
[tex]1698.569 \ m_3 =132.7[/tex]
[tex]\ m_3 = \dfrac{132.7}{1698.569}[/tex]
[tex]\mathbf{ m_3 = 0.078 \ kg/s}[/tex]
Hence; the amount of bleed steam required to heat 1 kg of feedwater in this unit is 0.078 kg/s
Consider a double-pipe counter-flow heat exchanger. In order to enhance its heat transfer, the length of the heat exchanger is doubled. Will the effectiveness of the exchanger double?
Answer:
effectiveness of the heat exchanger will not be double when the length of the heat exchanger is doubled.
Because effectiveness depends on NTU and not necessarily the length of the heat exchanger
You are tasked with designing an ICS/SCADA system. You must choose a type of ICS/SCADA system from the options listed below: Correctional facility Paint processing plant Water distribution facility Considering the type of system you chose from the list above, discuss the model you would use (time or event-based or a combination) and for what purposes. What considerations do you need to take into account in your design? How does the PLC fit into this system?
Answer:
The type of ICS/SCADA i choose is the Paint processing plant.
I will consider both the the time and event based as we need to mix various colors at different time interval and different quantities.
The PLC is used to process different tasks based on the commands assigned to it. In a paint processing plant, when a command from a computer is given to PLC for processing that tasks at that time whatever is the quantity is considered to mix it is carried out by PLC.
Explanation:
Solution
From the given question, i will select the Paint processing plant.
Here, the Supervisory Control and Data Acquisition System (SCADA) refers to a control system which uses computer network to control and manage the various processes from a single computer.
Since we consider the paint processing system for this we make use of both the time and event based as we need to mix various colors at different time interval and different quantities.
The programming Logic Controller (PLC): This is used to process different inputs based on the commands assigned to it.
In paint processing plant, when a command from a computer is assigned to PLC for processing that function at that time whatever is the quantity is required to mix it is carried out by PLC.
So, PLC is very useful device which is also the main processing device which carries out tasks assigned by the SCADA.