Answer:
C) experience a small induced magnetic moment when placed in an external magnetic field.
Explanation:
Diamagnetics materials are those that experience a small induced magnetic moment when placed in an external magnetic field. These materials, such as bismuth, copper, silver and lead, have elementary magnets in their compositions. When they are exposed to an external magnetic cap, these elemental magnets tend to follow an orientation contrary to the external magnetic field. As a result, a magnetic field is created in the opposite direction to the external magnetic field.
1.5 kg of air within a piston-cylinder assembly executes a Carnot power cycle with maximum and minimum temperatures of 800 K and 300 K, respectively. The heat transfer from the air during the isothermal compression is 80 kJ. At the end of the isothermal compression, the volume is 0.2 m3. Determine the volume at the beginning of the isothermal compression, in m3. Assume the ideal gas model for air and neglect kinetic and potential energy effects.
Answer:
Explanation:
Carton cycle consists of four thermodynamic processes . The first is isothermal expansion at higher temperature , then adiabatic expansion which lowers the temperature of gas . The third process is isothermal compression at lower temperature and the last process is adiabatic compression which increases the temperature of the gas to its original temperature .
So the given process of isothermal compression must have been done at the temperature of 300K , keeping the temperature constant .
Work done on gas at isothermal compression is equal to heat transfer .
work done on gas = 80 x 10³ J
work done on gas = n RT ln v₁ / v₂
n is number of moles v₁ and v₂ are initial and final volume
molecular weight of gas = 28.97 g
1.5 kg = 1500 / 28.97 moles
= 51.77 moles
work done on gas = n RT ln v₁ / v₂
Putting the values in the equation above
80 x 10³ = 51.78 x 8.31 x 300 x ln v₁ / .2
ln v₁ / .2 = .62
v₁ / .2 = 1.8589
v₁ = 0.37 m³
A magnetic field is entering into a coil of wire with radius of 2(mm) and 200 turns. The direction of magnetic field makes an angle 25° in respect to normal to surface of coil. The magnetic field entering coil varies 0.02 (T) in every 2 seconds. The two ends of coil are connected to a resistor of 20 (Ω).
A) Calculate Emf induced in coil
B) Calculate the current in resistor
C) Calculate the power delivered to resistor by Emf
Answer:
a) 2.278 x 10^-5 volts
b) 1.139 x 10^-6 Ampere
c) 2.59 x 10^-11 W
Explanation:
The radius of the wire r = 2 mm = 0.002 m
the number of turns N = 200 turns
direction of the magnetic field ∅ = 25°
magnetic field strength B = 0.02 T
varying time = 2 sec
The cross sectional area of the wire = [tex]\pi r^{2}[/tex]
==> A = 3.142 x [tex]0.002^{2}[/tex] = 1.257 x 10^-5 m^2
Field flux Φ = BA cos ∅ = 0.02 x 1.257 x 10^-5 x cos 25°
==> Φ = 2.278 x 10^-7 Wb
The induced EMF is given as
E = NdΦ/dt
where dΦ/dt = (2.278 x 10^-7)/2 = 1.139 x 10^-7
E = 200 x 1.139 x 10^-7 = 2.278 x 10^-5 volts
b) If the two ends are connected to a resistor of 20 Ω, the current through the resistor is given as
[tex]I[/tex] = E/R
where R is the resistor
[tex]I[/tex] = (2.278 x 10^-5)/20 = 1.139 x 10^-6 Ampere
c) power delivered to the resistor is given as
P = [tex]I[/tex]E
P = (1.139 x 10^-6) x (2.278 x 10^-5) = 2.59 x 10^-11 W
A skater spins at 3rev/s when she stretches her arms outward. If she keeps her fists on her chest she can spin at 4.5rev/s and her body inertia is 3kg.m2. What is her body inertia when she stretches her arms outward?
Answer:
Body inertia I = 4.5 kg/m^2
Explanation:
Here, we want to calculate the body inertia when the arms are stretched outwards.
We know from the question that angular momentum is conserved
Thus;
I * 3 = 4.5 * 3
I = 4.5 kg/m^2
A circular loop of wire has radius of 9.50 cm. A sinusoidal electromagnetic plane wave traveling in air passes through the loop, with the direction of the magnetic field of the wave perpendicular to the plane of the loop. The intensity of the wave at the location of the loop is 0.0295 W/m^2, and the wavelength of the wave is 6.40 m.
Required:
What is the maximum emf induced in the loop?
Answer:
The maximum emf induced in the loop is 0.132 Volts
Explanation:
Given;
radius of the circular loop, r = 9.5 cm
intensity of the wave, I = 0.0295 W/m²
wavelength, λ = 6.40 m
The intensity of the wave is given as;
[tex]I = \frac{B_o^2*c }{2\mu_o}[/tex]
where;
B₀ is the amplitude of the field
c is the speed of light = 3 x 10⁸ m/s
μ₀ is permeability of free space = 4π x 10⁻⁵ m/A
[tex]I = \frac{B_o^2*c }{2\mu_o}\\\\B_o^2 = \frac{I*2\mu_o}{c} \\\\B_o^2 = \frac{0.0295*2*4\pi*10^{-7}}{3*10^8} \\\\B_o^2 = 2.472 *10^{-16}\\\\B_o = \sqrt{2.472 *10^{-16}}\\\\ B_o = 1.572*10^{-8} \ T[/tex]
Area of the circular loop;
A = πr²
A = π(0.095)²
A = 0.0284 m²
Frequency of the wave;
f = c / λ
f = (3 x 10⁸) / (6.4)
f = 46875000 Hz
Angular velocity of the wave;
ω = 2πf
ω = 2π(46875000)
ω = 294562500 rad/s
The maximum induced emf is calculated as;
emf = B₀Aω
= (1.572 x 10⁻⁸)(0.0284)(294562500)
= 0.132 Volts
Therefore, the maximum emf induced in the loop is 0.132 Volts
Consider the following spectrum where two colorful lines (A and B) are positioned on a dark background. The violet end of the spectrum is on the left and the red end of the spectrum is on the right. A B 5. (1 point) What is the name for this type of spectrum? 6. (1 point) Transition A is associated with an electron moving between the n= 1 and n= 3 levels. Transition B is associated with an electron moving between the n= 2 and n= 5 levels. Which transition is associated with a photon of longer wavelength?
Answer:
Explanation:
a )
This type of spectrum is called line emission spectrum . Because it consists of lines . It is emission spectrum because it is due to emission of radiation from a source .
b ) The wavelength of a photon is inversely proportional to its energy . Photon due to transition between n = 1 and n = 3 will have higher energy than
that due to transition between n = 2 and n = 5 . So the later photon ( B) will have greater wavelength or photon due to transition between n = 2 and n = 5 will have greater wavelength .
A person standing 180m from the foot of a high building claps hi
hand and hears the echo 0.03minutes later. What is the speed
sound in air at that temperature?
A) 331m/s
B) 240m/s C) 200m/s D) 300m/s
Answer:
C) 200 m/s
Explanation:
The sound travels a total distance of 360 m in 0.03 minutes.
v = (360 m) / (0.03 min × 60 s/min)
v = 200 m/s
The _____________ is the thermonuclear fusion of hydrogen to form helium operating in the cores of massive stars on the main sequence
two resistors of resistance 10 ohm's and 20 ohm's are connected in parallel to a batery of e.m.f 12V. Calculate the current passing through the 20hm's resister
greater than: The electric potential energy of a proton at point A is _____ the electric potential energy of an proton at point B.
Answer:
[similar to]
Explanation:
it is the missing word
A piece of electronic equipment that is surrounded by packing material is dropped so that it hits the ground with a speed of 4 m/s. After impact, the equipment experiences an acceleration of a = 2kx, where k is a constant and x is the compression of the packing material. If the packing material experiences a maximum compression of 20 mm, determine the maximum acceleration of the equipment.
Answer:
Maximum acceleration is 800m/s^2
Explanation:
See attached file
Determine the position in the oscillation where an object in simple harmonic motion: (Be very specific, and give some reasoning to your answer.) has the greatest speed has the greatest acceleration experiences the greatest restoring force experiences zero restoring force g
Answer:
Explanation:
The greatest speed is attained at middle point or equilibrium point or where displacement from equilibrium point is zero .
When the object remains at one of the extreme point it experiences greatest acceleration but at that point velocity is zero . Due to acceleration , its velocity goes on increasing till it come to equilibrium point . At this point acceleration becomes zero . After that its velocity starts decreasing because of negative acceleration . Hence at middle point velocity is maximum .
The greatest acceleration is attained at maximum displacement or at one of the two extreme end .
Greatest restoring force too will be at position where acceleration is maximum because acceleration is produced by restoring force .
Restoring force is proportional to displacement or extension against restoring force . So it will be maximum when displacement is maximum .
Zero restoring force exists at equilibrium position or middle point or at point where displacement is zero . It is so because acceleration at that point is zero .
Flywheels are large, massive wheels used to store energy. They can be spun up slowly, then the wheel's energy can be released quickly to accomplish a task that demands high power. An industrial flywheel has a 1.5 m diameter and a mass of 250 kg. Its maximum angular velocity is 1200 rpm.
How long does it take the flywheel to reach top angular speed of 1200 rpm?
Answer:
t = 2.95 min
Explanation:
Given that,
The diameter of flywheeel, d = 1.5 m
Mass of flywheel, m = 250 kg
Initial angular velocity is 0
Final angular velocity, [tex]\omega_f=1200\ rpm = 126\ rad/s[/tex]
We need to find the time taken by the flywheel to each a speed of 1200 rpm if it starts from rest.
Firstly, we will find the angular acceleration of the flywheel.
The moment of inertia of the flywheel,
[tex]I=\dfrac{1}{2}mr^2\\\\I=\dfrac{1}{2}\times 250\times (0.75)^2\\\\I=70.31\ kg-m^2[/tex]
Now,
Let the torque is 50 N-m. So,
[tex]\alpha =\dfrac{\tau}{I}\\\\\alpha =\dfrac{50}{70.31}\\\\\alpha =0.711\ rad/s^2[/tex]
So,
[tex]t=\dfrac{\omega_f-\omega_i}{\alpha }\\\\t=\dfrac{126-0}{0.711}\\\\t=177.21\ s[/tex]
or
t = 2.95 min
A container is filled with fluid 1, and the apparent depth of the fluid is 9.00 cm. The container is next filled with fluid 2, and the apparent depth of this fluid is 6.86 cm. If the index of refraction of the first fluid is 1.37, what is the index of refraction of the second fluid
Answer:
The refractive index of fluid 2 is 1.78
Explanation:
Refractive index , n = real depth/apparent depth
For the first fluid, n = 1.37 and apparent depth = 9.00 cm.
The real depth of the container is thus
real depth = n × apparent depth = 1.37 × 9.00 cm = 12.33 cm
To find the refractive index of fluid index of fluid 2, we use the relation
Refractive index , n = real depth/apparent depth.
Now,the real depth = 12.33 cm and the apparent depth = 6.86 cm.
So, n = 12.33 cm/6.86 cm = 1.78
So the refractive index of fluid 2 is 1.78
Since the same container is used, real depth of fluid 1 is equal to the real depth of fluid 2. The index of refraction of the second fluid is 1.8
Given that a container is filled with fluid 1, and the apparent depth of the fluid is 9.00 cm. The container is next filled with fluid 2, and the apparent depth of this fluid is 6.86 cm. If the index of refraction of the first fluid is 1.37,
Then,
Index of refraction = [tex]\frac{Real depth}{Apparent depth}[/tex]
Real depth = Index of refraction x apparent depth
Since the same container is used, we can make an assumption that;
real depth of fluid 1 = real depth of fluid 2
That is,
1.37 x 9 = n x 6.86
Where n = Index of refraction for the second fluid.
make n the subject of formula
n = 12.33 / 6.86
n = 1.79
Therefore, the index of refraction of the second fluid is 1.8 approximately.
Learn more about refraction here: https://brainly.com/question/10729741
We repeat the experiment from the video, but this time we connect the wires in parallel rather than in series. Which wire will now dissipate the most heat?
Both wires will dissipate the same amount of heat.
A. The Nichrome wire (resistance 2.7)
B. The copper wire (resistance 0.1)
Answer: B. The copper wire (resistance 0.1)
Explanation: When resistance is in parallel, voltage (V) is the same but current is different for every resistance. Current (i) is related to voltage and resistance (R) by Ohm's Law
i = [tex]\frac{V}{R}[/tex]
So, since both wires are in parallel, they have the same voltage but because the copper wire resistance is smaller than Nichrome wire, the first's current will be bigger.
Every resistor in a circuit dissipates electrical power (P) that is converted into heat energy. The dissipation can be found by:
P = [tex]i^{2}*R[/tex]
As current for copper wire is bigger than nichrome, power will be bigger and it will dissipate more heat.
In conclusion, the copper wire will dissipate more heat when connected in parallel.
If the magnetic field steadily decreases from BBB to zero during a time interval ttt, what is the magnitude III of the induced current
Answer:
Using ohms law
The current is found from Ohm's Law.
I = V /R = E /R = Bxy /Rt.
An object on a rope is lowered steadily decreasing speed. Which is true?
A) The tope tensions is greater than the objects weight
B) the rope tension equals the objects weight
C)the rope tension is less than the objects weight
D) the rope tension can’t be compared to the objects weight
Answer:
C) the rope tension is less than the objects weight
Explanation:
According to Newton's Second Law, when an unbalanced or net force is applied to a body, it produces an acceleration in the body in the direction of the net force itself.
In this scenario, we have two forces acting on the object. First is the weight of object acting downward. Second is the tension in the rope acting upwards.
Since, the object is being lowered in the direction of weight. Therefore, weight of the object must be greater than the tension in the rope. So, the net force has the downward direction and the object is lowered. Hence, the correct option is:
C) the rope tension is less than the objects weight
Jane is collecting data for a ball rolling down a hill. she measure out a set of different distances and then proceeds to use a stopwatch to find the time it takes the ball to roll each distance
Answer:
The Independent variable in this experiment is the time taken by the ball to roll down each distance.
The dependent variable is the distance through which the ball rolls
The control variables are: slope of hill, weight, of the ball, size of ball, wind speed, surface characteristics of the ball.
Explanation:
The complete question is
Jane is collecting data for a ball rolling down a hill. She measures out a set of different distances and then proceeds to use a stop watch to find the time it takes the ball to roll. What are the independent, dependent, and control variables in this experiment?
Independent variable have their values not dependent on any other variable in the scope of the experiment. The time for the ball to roll down the hill is not dependent on any other variable in the experiment. Naturally, some common independent variables are time, space, density, mass, fluid flow rate.
A dependent variable has its value dependent on the independent variable in the experiment. The value of the distance the ball rolls depends on the time it takes to roll down the hill.
The relationship between the dependent and independent variables in an experiment is given as
y = f(x)
where y is the output or the dependent variable,
and x is the independent variable.
Control variables are those variable that if not held constant could greatly affect the results of an experiment. For an experiment to be more accurate, control variables should be confined to a given set of value throughout the experiment.
Two factors that regulate (control) glandular secretion.
Answer:
The factors include age and puberty
Explanation:
Glandular secretion release chemicals such as hormones in response to the body’s metabolic needs.
As an individual ages , the metabolic rate of the body also reduces . This is due to the stress and ageing of the cells of the body. This explains why glandular secretion is optimal with young people and Lower in older people. It also explains why the immune system of a young person is mostly stronger than older people.
Puberty is another factor which affects glandular secretion as during puberty there is usually a high amount of hormonal changes due to high levels of secretions of some hormones. These hormones could however inhibit the other glandular secretions.
Suppose there is a uniform electric field pointing in the positive x-direction with a magnitude of 5.0 V/m. The electric potential is measured to be 50 V at the position x = 10 m. What is the electric potential at other positions?
Position [m] = (−20)--- (0.00) ---(10)--- (11)--- (99)
Electric Potential [V]=
Answer:
Electric potential at position, x = -20 m, = -100 V
Electric potential at position, x = 0 m, = 0
Electric potential at position, x = 10 m, = 50 V
Electric potential at position, x = 11 m, = 55 V
Electric potential at position, x = 99 m, 495 V
Explanation:
Given;
magnitude of electric field, E = 5.0 V/m
at position x = 10 m, electric potential = 50 V
Electric potential at position, x = -20 m
V = Ex
V = 5 (-20)
V = -100 V
Electric potential at position, x = 0 m
V = Ex
V = 5(0)
V = 0
Electric potential at position, x = 10 m
V = Ex
V = 5(10)
V = 50 V
Electric potential at position, x = 11 m
V = Ex
V = 5(11)
V = 55 V
Electric potential at position, x = 99 m
V = Ex
V = 5(99)
V = 495 V
A proton moving at 4.80 106 m/s through a magnetic field of magnitude 1.74 T experiences a magnetic force of magnitude 7.00 10-13 N. What is the angle between the proton's velocity and the field? (Enter both possible answers from smallest to largest. Enter only positive values between 0 and 360.)
Answer:
31.55° and 148.45°
Explanation:
Formula for calculating the force experiences by the proton placed in a magnetic field is as expressed below;
F = qvBsinθ where;
F is the magnetic force experienced by the proton
q is the charge on the proton
v is the velocity of the proton
B is the magnetic field
θ is the angle between the proton's velocity and the field (Required)
Given parameters
F = 7.00 * 10⁻¹³N
q = 1.602*10⁻¹⁹C
v = 4.80 * 10⁶ m/s
B = 1.74 T
θ =?
From the formula F = qvBsinθ;
sinθ = F/qvB
sinθ = 7.00 * 10⁻¹³/1.602*10⁻¹⁹* 4.80 * 10⁶*1.74
sinθ = 7.00 * 10⁻¹³/13.38*10⁻¹³
sinθ = 0.5231689 * 10⁰
sinθ = 0.5231689
θ = sin⁻¹0.5231689
θ = 31.55°
The following are the positive values of the angle between 0° and 360°
Sin is positive in the first and second quadrant. In the second quadrant the angle is equal to 180°-31.55° = 148.45°.
Hence the possible values of the angle from smallest to largest are 31.55° and 148.45°
g a conductor consists of an infinite number of adjacent wires, each infinitely long. If there are n wires per unit length, what is the magnitude of B~
Answer:
B=uonI/2
Explanation:
See attached file
Calculate the power of the eye in D when viewing an object 5.70 m away. (Assume the lens-to-retina distance is 2.00 cm. Enter your answer to at least one decimal place.)
Answer:
Power=50.17dioptre
Power=50.17D
Explanation:
P=1/f = 1/d₀ + 1/d₁
Where d₀ = the eye's lens and the object distance= 5.70m=
d₁= the eye's lens and the image distance= 0.02m
f= focal length of the lense of the eye
We know that the object can be viewed clearly by the person ,then image and lens of the eye's distance needs to be equal with the retinal and the eye lens distance and this distance is given as 0.02m
Therefore, we can calculate the power using above formula
P= 1/5.70 + 1/0.02
Power=50.17dioptre
Therefore, the power the eye's is using to see the object from distance is 5.70D
Two objects are in all respects identical except for the fact that one was coated with a substance that is an excellent reflector of light while the other was coated with a substance that is a perfect absorber of light. You place both objects at the same distance from a powerful light source so they both receive the same amount of energy U from the light. The linear momentum these objects will receive is such that:
Answer:
absorbent p = S / c
reflective p = 2S/c
Explanation:
The moment of radiation on a surface is
p = U / c
where U is the energy and c is the speed of light.
In the case of a fully absorbent object, the energy is completely absorbed. The energy carried by the light is given by the Poynting vector.
p = S / c
in the case of a completely reflective surface the energy must be absorbed and remitted, therefore there is a 2-fold change in the process
p = 2S/c
An object has an acceleration of 6.0 m/s/s. If the net force was doubled and the mass was one-third the original value, then the new acceleration would be _____ m/s/s.
Hahahahaha. Okay.
So basically , force is equal to mass into acceleration.
F=ma
so when F=ma , we get acceleration=6m/s/s
Force is doubled.
Mass is 1/3 times original.
2F=1/3ma
Now , we rearrange , and we get 6F=ma
So , now for 6 times the original force , we get 6 times the initial acceleration.
So new acceleration = 6*6= 36m/s/s
Scientists studying an anomalous magnetic field find that it is inducing a circular electric field in a plane perpendicular to the magnetic field. The electric field strength is 4.0 mV/m at a point 1.5 m away from the center of the circle. At what rate is the magnetic field changing?
Answer:
The rate at which the magnetic field changes is [tex]\frac{\Delta B }{\Delta t } = - 5.33*10^{-3} \ T/ s[/tex]
Explanation:
From the question we are told that
The electric field strength is [tex]E = 4.0 mV/m = 4.0 *10^{-3} V/m[/tex]
The radius of the circular region where the electric field is induced is
[tex]d = 1.5 \ m[/tex]
Generally the induced electric field is mathematically represented as
[tex]E = - \frac{r}{2} * \frac{\Delta B }{\Delta t }[/tex]
The negative sign show that the induced electric field is acting in opposite direction to the change in magnetic field
Where [tex]\frac{\Delta B }{\Delta t }[/tex] is the change in magnetic field
So
[tex]\frac{\Delta B }{\Delta t } = - \frac{2 * E }{r}[/tex]
substituting values
[tex]\frac{\Delta B }{\Delta t } = - \frac{2 * 4.0 *10^{-3}}{ 1.5 }[/tex]
[tex]\frac{\Delta B }{\Delta t } = - 5.33*10^{-3} \ T/ s[/tex]
If an astronomer wants to find and identify as many stars as possible in a star cluster that has recently formed near the surface of a giant molecular cloud (such as the Trapezium cluster in the Orion Nebula), what instrument would be best for her to use
Answer:
Infrared telescope and camera
Explanation:
An infrared telescope uses infrared light to detect celestial bodies. The infrared radiation is one of the known forms of electromagnetic radiation. Infrared radiation is given off by a body possessing some form of heat. All bodies above the absolute zero temperature in the universe radiates some form of heat, which can then be detected by an infrared telescope, and infrared radiation can be used to study or look into a system that is void of detectable visible light.
Stars are celestial bodies that are constantly radiating heat. In order to see a clearer picture of the these bodies, Infrared images is better used, since they are able to penetrate the surrounding clouds of dust, and have located many more stellar components than any other types of telescope, especially in dusty regions of star clusters like the Trapezium cluster.
A 4g bullet, travelling at 589m/s embeds itself in a 2.3kg block of wood that is initially at rest, and together they travel at the same velocity. Calculate the percentage of the kinetic energy that is left in the system after collision to that before.
Answer:
The percentage of the kinetic energy that is left in the system after collision to that before is 0.174 %
Explanation:
Given;
mass of bullet, m₁ = 4g = 0.004kg
initial velocity of bullet, u₁ = 589 m/s
mass of block of wood, m₂ = 2.3 kg
initial velocity of the block of wood, u₂ = 0
let the final velocity of the system after collision = v
Apply the principle of conservation of linear momentum
m₁u₁ + m₂u₂ = v(m₁+m₂)
0.004(589) + 2.3(0) = v(0.004 + 2.3)
2.356 = 2.304v
v = 2.356 / 2.304
v = 1.0226 m/s
Initial kinetic energy of the system
K.E₁ = ¹/₂m₁u₁² + ¹/₂m₂u₂²
K.E₁ = ¹/₂(0.004)(589)² = 693.842 J
Final kinetic energy of the system
K.E₂ = ¹/₂v²(m₁ + m₂)
K.E₂ = ¹/₂ x 1.0226² x (0.004 + 2.3)
K.E₂ = 1.209 J
The kinetic energy left in the system = final kinetic energy of the system
The percentage of the kinetic energy that is left in the system after collision to that before = (K.E₂ / K.E₁) x 100%
= (1.209 / 693.842) x 100%
= 0.174 %
Therefore, the percentage of the kinetic energy that is left in the system after collision to that before is 0.174 %
An 1300-turn coil of wire that is 2.2 cmcm in diameter is in a magnetic field that drops from 0.14 TT to 0 TT in 9.0 msms . The axis of the coil is parallel to the field.
What is the emf of the coil? (in V)
Answer:
The induced emf is [tex]\epsilon =7.68 \ V[/tex]
Explanation:
From the question we are told that
The number of turns is [tex]N = 1300 \ turns[/tex]
The diameter is [tex]d = 2.2 \ cm = 2.2*10^{-2}[/tex]
The initial magnetic field is [tex]B_i = 0.14 \ T[/tex]
The final magnetic field is [tex]B_f = 0 \ T[/tex]
The time taken is [tex]dt = 9.0ms = 9.0*10^{-3} \ s[/tex]
The radius is mathematically evaluated as
[tex]r = \frac{d}{2 }[/tex]
substituting values
[tex]r = \frac{2.2 *10^{-2}}{2 }[/tex]
[tex]r = 1.1*10^{-2} \ m[/tex]
The induced emf is mathematically represented as
[tex]\epsilon =- N * \frac{d\phi }{dt }[/tex]
Where [tex]d\phi[/tex] is the change in magnetic field which is mathematically represented as
[tex]d\phi = dB * A * cos\theta[/tex]
=> [tex]d\phi = [B_f - B_i ] * A * cos\theta[/tex]
Here [tex]\theta = 0[/tex] given that the axis of the coil is parallel to the field
Also A is the cross-sectional area which is mathematically represented as
[tex]A = \pi r^2[/tex]
substituting values
[tex]A = 3.142 * [1.1*10^{-2}]^2[/tex]
[tex]A = 3.8 *10^{-4] \ m^2[/tex]
So
[tex]d\phi = [0 - 0.14 ] * 3.8*10^{-4}[/tex]
[tex]d\phi = -5.32*10^{-5} \ weber[/tex]
So
[tex]\epsilon =- 1300 * \frac{-5.32*10^{-5} }{ 9.0*10^{-3} }[/tex]
[tex]\epsilon =7.68 \ V[/tex]
Two protons are released from rest, with only the electrostatic force acting. Which of the following statements must be true about them as they move apart? (There could be more than one correct choice.)a. Their electrical potential energy keeps decreasing.b. Their acceleration keeps decreasing.c. Their kinetic energy keeps increasing.d. Their kinetic energy keeps decreasing.e. Their electric potential energy keeps increasing.
Answer:
Explanation:
correct options
a ) Their electrical potential energy keeps decreasing
Actually as they move apart , their electrical potential energy decreases due to increase of distance between them and kinetic energy increases
so a ) option is correct
b ) Their acceleration keeps decreasing
As they move apart , their mutual force of repulsion decreases due to increase of distance between them so the acceleration decreases .
c ) c. Their kinetic energy keeps increasing
Their kinetic energy increases because their electrical potential energy decreases . Conservation of energy law will apply .
The moving apart should be true statements:
a. The electrical potential energy should be reduced.
b. The acceleration should be reduced.
c. The kinetic energy should be increased.
True statements related to moving apart:At the time when the moving part, there is the reduction of the electric potential energy because there is a rise in the distance due to which the increment of the kinetic energy. The reduction of the mutual force of repulsion because of increment in the distance due to this the acceleration should be reduced. There is the increase in the kinetic energy due to the reduction of the electrical potential energy. here the law of conversation of energy should be applied.
Learn more about energy here: https://brainly.com/question/10658188
A solenoid of length 2.40 m and radius 1.70 cm carries a current of 0.190 A. Determine the magnitude of the magnetic field inside if the solenoid cons
Complete question:
A solenoid of length 2.40 m and radius 1.70 cm carries a current of 0.190 A. Determine the magnitude of the magnetic field inside if the solenoid consists of 2100 turns of wire.
Answer:
The magnitude of the magnetic field inside the solenoid is 2.089 x 10⁻⁴ T.
Explanation:
Given;
length of solenoid, L = 2.4 m
radius of solenoid, R = 1.7 cm = 0.017 m
current in the solenoid, I = 0.19 A
number of turns of the solenoid, N = 2100 turns
The magnitude of the magnetic field inside the solenoid is given by;
B = μnI
Where;
μ is permeability of free space = 4π x 10⁻⁷ m/A
n is number of turns per length = N/L
I is current in the solenoid
B = μnI = μ(N/L)I
B = 4π x 10⁻⁷(2100 / 2.4)0.19
B = 4π x 10⁻⁷ (875) 0.19
B = 2.089 x 10⁻⁴ T
Therefore, the magnitude of the magnetic field inside the solenoid is 2.089 x 10⁻⁴ T.