The example of a reversed heat engine is a refrigerator., the correct answer is "refrigerator" as an example of a reversed heat engine.
A refrigerator operates by removing heat from a colder space and transferring it to a warmer space, which is the opposite of how a heat engine typically operates. In a heat engine, heat is taken in from a high-temperature source, and part of that heat is converted into work, with the remaining heat being rejected to a lower-temperature sink. In contrast, a refrigerator requires work input to transfer heat from a colder region to a warmer region, effectively reversing the direction of heat flow.
Learn more about heat engine here:
brainly.com/question/30853813
#SPJ11
Explain the advantages and disadvantages of the 2 ray ground reflection model in the analysis of path loss. (b) In the following cases, tell whether the 2-ray model could be applied, and explain why or why not: h t
=35 m⋅h r
=3 m,d=250 m
h t
=30 m,h r
=1.5 m⋅d=450 m
The two-ray ground reflection model in the analysis of path loss has the following advantages and disadvantages:
Advantages: It provides a quick solution when using hand-held calculators or computers because it is mathematically easy to manipulate. There is no need for the distribution of the building, and the model is applicable to any structure height and terrain. The range is only limited by the radio horizon if the mobile station is located on a slope or at the top of a hill or building.
Disadvantages: It is an idealized model that assumes perfect ground reflection. The model neglects the impact of environmental changes such as soil moisture, surface roughness, and the characteristics of the ground.
The two-ray model does not account for local obstacles, such as building and foliage, in the transmission path.
Therefore, the two-ray model could not be applied in the following cases:
Case 1hₜ = 35 m, hᵣ = 3 m, d = 250 m The distance is too short, and the building is not adequately covered.
Case 2hₜ = 30 m, hᵣ = 1.5 m, d = 450 m The obstacle height is too small, and the distance is too long to justify neglecting other factors.
To know more about reflection visit:
https://brainly.com/question/15487308
#SPJ11
To achieve maximum power transfer between a 44 Ω source and a load ZL (ZL > ZG) using a transmission line with a characteristic impedance of 44 Ω, an inductor with a reactance of 82 Ω is connected in series with the source. Determine the distance from the load, ZL, in terms of wavelengths where the inductor should be connected. Length = λ
The inductor should be connected at a distance of 2 wavelengths from the load, ZL, to achieve maximum power transfer.
To determine the distance, we need to consider the conditions for maximum power transfer. When the characteristic impedance of the transmission line matches the complex conjugate of the load impedance, maximum power transfer occurs. In this case, the load impedance is ZL, and we have ZL > ZG, where ZG represents the generator impedance.
Since the transmission line has a characteristic impedance of 44 Ω, we need to match it to the load impedance ZL = 44 Ω + jX. By connecting an inductor with a reactance of 82 Ω in series with the source, we effectively cancel out the reactance of the load impedance.
The electrical length of the transmission line is given by the formula: Length = (2π / λ) * Distance, where λ is the wavelength. Since the inductor cancels the reactance of the load impedance, the transmission line appears purely resistive. Hence, we need to match the resistive components, which are 44 Ω.
For maximum power transfer to occur, the inductor should be connected at a distance of 2 wavelengths from the load, ZL.
Learn more about electrical length here
brainly.com/question/13572284
#SPJ11
Develop a minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter.
A minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter can be developed.
To develop a minimum-multiplier realization of a length-7 Type 3 Linear Phase FIR Filter, we need to understand the key components and design considerations involved. A Type 3 Linear Phase FIR Filter is characterized by its linear phase response, which means that all frequency components of the input signal experience the same constant delay. The minimum-multiplier realization aims to minimize the number of multipliers required in the filter implementation, leading to a more efficient design.
In this case, we have a length-7 filter, which implies that the filter has 7 taps or coefficients. Each tap represents a specific weight or gain applied to a delayed version of the input signal. To achieve a minimum-multiplier realization, we can exploit the symmetry properties of the filter coefficients.
By carefully analyzing the symmetry properties, we can design a structure that reduces the number of required multipliers. For a length-7 Type 3 Linear Phase FIR Filter, the minimum-multiplier realization can be achieved by utilizing symmetric and anti-symmetric coefficients. The symmetric coefficients have the same value at equal distances from the center tap, while the anti-symmetric coefficients have opposite values at equal distances from the center tap.
By taking advantage of these symmetries, we can effectively reduce the number of multipliers needed to implement the filter. This results in a more efficient and resource-friendly design.
Learn more about multiplier
brainly.com/question/31406180
#SPJ11