Answer:
12
Explanation:
Answer:
12?
Explanation:
A gyroscope consists of a rotating disk with a 25 cm radius suitably mounted at the midpoint of a 20 cm long axle so that it can spin and precess freely. One end is supported by a stand. The disk spins at 2000 rpm. The mass of the disk is 2 kg, and the axle can be taken as massless.
Required:
a. Draw the gyroscope, indicating the direction of the initial angular speed and the initial angular momentum. Choose a direction for the spin of the disk.
b. Draw the torque due to gravity about the support point.
c. What direction will your gyroscope precess once you release it?
d. Find the time required for one precession of the gyroscope if it is supported at one end of the axle and it precesses in the horizontal plane.
Answer:
A) attached below
B) attached below
C) Anti-clockwise
D) 3.27 secs
Explanation:
A) Diagram of the gyroscope indicating direction of
attached below
B) Diagram of torque due to gravity about support point
Attached below
C) The direction the gyroscope will precess is ANTICLOCKWISE
D) Time required for one precession of the gyroscope
use the relation below
MgL = ΔIw / Δt
∴ Δt = ΔIw / MgL
=( 1/2 * 2 * 0.25^2 * 2π * 2000 ) / ( 2 * 10 * 0.2 * 60 )
= 3.27 secs
A student must determine how the mass of a block affects the period of oscillation when the block is attached to a vertical spring. The value of the spring constant is known. The student writes the following experimental procedure.
1. Use an electronic balance to measure the mass of the block.
2. Attach the block to the vertical spring.
3. Displace the block from the system's equilibrium position to a new vertical position.
4. Release the block from rest.
5. Use a meterstick to measure the vertical displacement of the center of mass of the block from the system's equilibrium position to its maximum vertical position above the equilibrium position.
6. Use a stopwatch to measure the time it takes for the system to make ten complete oscillations.
7. Repeat the experiment for different vertical displacements and block masses.
Which of the following steps of the procedure should the student revise to make the determination? Justify your selection.
a. Step 3, because the student must specify whether the new vertical position should be above or below the system's equilibrium position.
b. Step 5, because the meterstick should be used to measure total displacement of the system from its lowest vertical position to its highest vertical position.
c. Step 6, because the stopwatch should be used only to measure the time it takes for the system to make 1 complete oscillation.
d. Step 7, because the experiment should not be repeated for different vertical displacements and block masses.
Answer:
the step that the student should change is step 7
Explanation:
The movement of the spring with block is a simple harmonic type movement, so the procedure proposed by the student is correct, but we must take some care.
Step 3 is important since each movement will be started with similar conditions, also if any displacement is very large we can get out of the linear approximation of Hooke's law, for which we need to know the equilibrium point, since from this point displacements will be measured.
Step 6 should be changed to measure various oscillations to find the average period and thus decrease the error in the time reading.
Step 7 is wrong since the objective of the experiment is to analyze the effect of different masses in the period of oscillation and this step prevents this objective from being carried out.
In conclusion, the step that the student should change is step 7
The step that should be revised to make the determination is c. Step 6, because the stopwatch should be used only to measure the time it takes for the system to make 1 complete oscillation.
Why should step 6 be revised?The student is trying to find the effect of the mass of the block on the period of oscillation in different vertical displacements.
The best way to do this is to measure the time taken per oscillation as this would show a much clearer picture to find the effect of the mass on the oscillation. Timing 10 oscillations will yield incorrect results.
In conclusion, option C is correct.
Find out more on measuring the effect of mass on oscillation at https://brainly.com/question/14745507.
A flying stationary kite is acted on by a force of 9.8 N downward. The wind exerts a force of 45 N at an angle of 50.0 degrees above the horizontal. Find the force that the string exerts on the kite.
Answer:
38 N, 40.0° below the horizontal
Explanation:
Force exerted by an object equals mass times acceleration of that object: F = m ⨉ a. To use this formula, you need to use SI units: Newtons for force, kilograms for mass, and meters per second squared for acceleration.
What is the relationship between a magnets magnetic force and a magnetic field?
Answer:
Electric forces exist among stationary electric charges; both electric and magnetic forces exist among moving electric charges. The magnetic force between two moving charges may be described as the effect exerted upon either charge by a magnetic field created by the other.
Answer:
i think this could help you
A uniform rod of length 50cm and mass 0.2kg is placed on a fulcrum at a distance of 40cm from the left end of the rod. At what distance from the left end of the rod should a 0.6kg mass be hung to balance the rod?
a.48 cm
b. 50 cm
c. 45 cm
d. the rod can not be balanced with this mass. e.42 cm
Answer:
x = 45 cm
Explanation:
Given that,
The length of a rod, L = 50 cm
Mass, m₁ = 0.2 kg
It is at 40cm from the left end of the rod.
We need to find the distance from the left end of the rod should a 0.6kg mass be hung to balance the rod.
The centre of mass of the rod is at 25 cm.
Taking moments of both masses such that,
[tex]15\times 0.2=x\times 0.6\\\\x=\drac{3}{0.6}\\\\x=5\ cm[/tex]
The distance from the left end is 40+5 = 45 cm.
Hence, at a distance of 45 cm from the left end it will balance the rod.
a shopping bag can provide an upward force of 65N before breaking. A shopper puts 5 kg of groceries in the bag. If the shopper tries to lift the bag with an upward acceleration of 2 m/s/s, will the bag break?
Answer:
Since Force is Mass * Acceleration, the equation would be:
5kg * 2m^2 = 10N
(10N is less than 65N)
Therefore, it would not be enough force for the bag to break.
how many universes out there?
Answer:
onlu 1 universe
Explanation:
Drag and drop a term to match these examples with the correct level of organization.
Tissue:
Organ:
Organ system:
--------------------------------------------------------------------------------------------------------------
A-cardiac muscle
B-circulatory system
C-heart
D-human body
Answer:
Tissue: cardiac muscle
Organ: Heart
Organ System: Human Body, Circulatory System
Explanation:
The cardiac muscle makes up an organ, making it a tissue
The Heart makes up a organ system, making it an organ
Both the human Body and The Circulatory System make up an organism, making them organisms
State the role of an electromotive force (EFF) in a current flow
Answer:
The emf source acts as a charge pump, moving negative charges from the positive terminal to the negative terminal to maintain the potential difference. This increases the potential energy of the charges and, therefore, the electric potential of the charges.
Explanation:
MARK AS BRAINLEST!!
I stand 0.72 meters in front of a mirror and look at the person on the other side who looks like me. That person is actually younger than me by a small amount. How much?
Answer:
Younger by nanoseconds
Explanation:
Not entirely sure :O
An african bush elephant has a mass of 5,900 kg and is on a skateboard traveling to the
left at 10 m/s. What is her momentum?
Water droplets forming on the outside of a cold glass of water on a hot, summer day is a example of which part of the water cycle?
Answer:
Condensation can also produce water droplets on the outside of soda cans or glasses of cold water. When warm air hits the cold surface, it reaches its dew point and condenses. This leaves droplets of water on the glass or can.
Explanation:
who else up at 1:45 for homework
it's 9:46AM for me lol
Answer:
lol it's 11:46 pm for me, just trying to get every done before tommorow aka the last day of school
Light of wavelength 633 nm from a He-Ne laser passes through a circular aperture and is observed on a screen 4.0 m behind the aperture. The diameter of the central bright area is 5.4 cm. What is the diameter of the aperture?
Answer:
The answer is "[tex]1.144 \times 10^{-4} \ m[/tex]".
Explanation:
[tex]w=\frac{2.44 \lambda L}{D}\\\\D=\frac{2.44 \lambda L}{w}\\\\[/tex]
[tex]=\frac{2.44 \times 633 \times 10^{-9}\times 4 }{0.054}\\\\=\frac{6178.08\times 10^{-9}}{0.054}\\\\=1.144 \times 10^{-4} \ m[/tex]
The center of mass of a uniform disk of radius
Ris located where?
Answer:
At the centre
Explanation:
To prove the position of the centre of mass, usually we take a strip across the circular disc and call it dy; calculate the length of the strip; calculate the mass per unit area of the disc. And then when we carry out some integral operations using R and -R as the boundaries we will arrive at y_cm = 0 which means the centre y_cm is at the centre of mass of this uniform disc.
HELP: I’ve been stuck on this problem for a while now.
Answer:
a.work done=force *displacement
=500N*46m
=23000 Joule
b.power=work done/time taken
=23000/25
=920 watt
c.GPE=m*g*h(m=mass,g=gravity due to acceleration,h=height)
=60kg*9.8m/s*14m
=8232 joule
Explanation:
An object is placed of 20cm from a concave mirror whose focal length is 10cm. what is the distance of image formed ?
Answer:
Answer 43cm
Explenation:
if you divide it to 4 it will convert to 43 so answer is 43cm if this wrong im sorry but mine is perfect thankss :)
WILL MARK BRAINLIEST PLS HELP. A 3.33 x 10-6 F capacitor stores
8.15 x 10-4 J of energy. What is the
voltage across the capacitor?
(Pic shown)
Answer:
15.64 V
Explanation:
From the question given above, the following data were obtained:
Capacitor (C) = 3.33x10¯⁶ F
Energy (E) = 8.15×10¯⁴ J
Voltage (V) =?
The voltage across the capacitor can be obtained as follow:
E = ½CV²
8.15×10¯⁴ = 3.33x10¯⁶ × V²
Divide both side by 3.33x10¯⁶
V² = 8.15×10¯⁴ / 3.33x10¯⁶
Take the square root of both side
V = √(8.15×10¯⁴ / 3.33x10¯⁶)
V = 15.64 V
Thus, the voltage across the capacitor is 15.64 V
Answer:
22.12
Explanation:
on accellus
A physics professor demonstrates the Doppler effect by tying a 900 Hz sound generator to a 1.0- m -long rope and whirling it around her head in a horizontal circle at 100 rpm .
1. What is the difference between the highest frequency heard by a student in the classroom and the initial frequency of the sound generator?
2. What is the difference between the lowest frequency heard by a student in the classroom and the initial frequency of the sound generator?
What is the purpose of a tuner in a radio?
Answer:
A tuner is a subsystem that receives radio frequency (RF) transmissions and converts the selected carrier frequency and its associated bandwidth into a fixed frequency that is suitable for further processing, usually because a lower frequency is used on the output.
hope it helps ya mate.
Answer:
The tuner selects only the signal of a specific frequency and rejects the rest.
Explanation:
pf
Suppose that a car weighing 4000 pounds is supported by four shock absorbers Each shock absorber has a spring constant of 6500 lbs/foot, so the effective spring constant for the system of 4 shock absorbers is 26000 lbs/foot. Assume no damping and determine the period of oscillation of the vertical motion of the car.
Required:
a. Assume no damping and determine the period of oscillation of the vertical motion of the car.
b. After 10 seconds the car body is 1/3 foot above its equilibrium position and at the high point in its cycle. What were the initial conditions?
Answer:
0.43622 seconds
0.9158 foot
-4.43 ffot/sec
Explanation:
we first find the period of oscillation
= 2π√w/gk
= 2π√4000/32x2600
= 2π√0.00481
= 2π0.0694
= 0.43622
b. we find the angular velocity
2π/T
= 2π/0.43622
= 14.41 rad/sec
we find displacement
rom the calculation in the attachment
Ф = -144.1
initial condition
1*cos(-144.1 rad)
= 0.9158 foot
initial velocity of the car
= (-1)(14.41)sin(ω(0)-144.1)
= -4.44 foot/sec
~⇆First person to accurently tell me why a ball falls to the ground I will give brainliest to and you can have the points⇄~
║-This isn't for anything I'm doing just for fun and easy points-║
Answer:
because of gravity the ball falls
Answer:
Gravity
Explanation:
Gravity is the force the world gives which I magnetic and yeah-
A spacecraft is powered by electricity generated by the heat produced when 23894Pu decays with a half-life of 87.75 y. Engineers predict that the spacecraft will have insufficient power to operate its instruments when the amount of 238 94Pu in its power generators drops below 67 % of the amount it had at launch on September 1, 1977
Required:
In what year will its instruments cease to function?
A hammer taps on the end of a 5.0-mm-long metal bar at room temperature. A microphone at the other end of the bar picks up two pulses of sound, one that travels through the metal and one that travels through the air. The pulses are separated in time by 9.00 ms.
Required:
What is the speed of sound in this metal?
Answer:
896.5 m/s
Explanation:
Given that :
Length of metal bar, λ= 5 m
Velocity in air, v = 343 m/s
Change in air frequency : = λ / v
f = 5 / 343 = 0.0145772 s = 14.5772 ms
Seperation time = 9ms
Change in time, t = 14.5772 - 9 = 5.5772 ms
Recall :
Velocity = Distance / time
V = 5m / 5.5772 * 10^-3 s
V = 896.50720 m/s
Velocity = 896.5 m/s
Suppose that we use a heater to boil liquid nitrogen (N2 molecules). 4480 J of heat turns 20 g of liquid nitrogen into gas. Note that the latent heat is equal to the change in enthalpy, and that liquid nitrogen boils at 77 K. The system is kept at a constant pressure of 1 atm. Assuming that you can treat the gas as ideal gas and that the volume of the liquid is approximately zero, compute the binding energy of a nitrogen molecule in the liquid. (the binding energy is the difference in internal energy per molecule between the liquid and gas)
a. 4.2e^-18 J
b. 9.4e^-21 J
c. 4.8e^ 24 J
d. 2.1e^-19 J
e. 1.3e^-23 J
How far an object moves from a reference point is known as
type your answer...
Answer:
distance
hope it helps
Explanation:
-
SOMONE PLEASE HELP ASAP!!!!
violet
it has the shortest wavelength
Explain the geometrical meaning of vertor Product of
two vectors
Answer:
Explained below
Explanation:
For the geometric meaning, I've attached a parallelogram showing two vectors a and B and also the angle between them as θ.
We can see that the two vectors are adjacent to each other.
So the magnitude of the product of the two vectors is simply the area of the parallelogram which is base x height. Thus;
Magnitude = |a| sin θ × |b|
This can be rewritten as;
|a|•|b| sin θ
leafy greens are considered the healthiest vegetable because of their ___ nutrients profile
Dense because food do be dense tho
Write a method which prevents ice from melting quickly.
Answer:
blocks of ice are usually covered with cloth or sawdust while being stored