g Given a state of stress and , where is a positive constant with units of , what is the maximum allowable value of to avoid failure according to the Tresca/von Mises criterion if the material has yield strength .
Answers
Answer: Hello your question is poorly written attached below is the complete question
answer :
: max value to avoid failure = 59 MPa
; max value to avoid failure = 34.064 Mpa
Explanation:
Attached below is the detailed solution of the given problem
For Tresca criterion : max value to avoid failure = 59 MPa
For Von-Nissen criterion ; max value to avoid failure = 34.064 Mpa
Related Questions
When you're running a test bench, you would like to include a printout to the screen to inform yourself on the status of the current simulation. Which command you could use to monitor specific variables or signals in a simulation every time one of the signals changes value?
Answers
Answer:
$Monitor
Explanation:
The command that would be used when running a test bench to monitor variables or signals ( i.e. changes in the values of specific variables and signa)
is the $Monitor command
This command is also used to monitor the varying values of signals during simulation.
IV. An annealed copper strip 9 inches wide and 2.2 inches thick, is rolled to its maximum possible draft in one pass. The following properties of annealed copper are given: strength coefficient is 90,000 psi; true strain at the onset of non-uniform deformation is 0.45; and, engineering strain at yield is 0.11. The coefficient of friction between strip and roll is 0.2. The roll radius is 14inches and the rolls rotate at 150 rpm. Calculate the roll-strip contact length. Calculate the absolute value of thetrue strain that the strip undergoes in this operation. Determine the average true stress of the strip in theroll gap. Calculate the roll force. Calculate the horsepower required.
Answers
Answer:
13.9357 horse power
Explanation:
Annealed copper
Given :
Width, b = 9 inches
Thickness, [tex]$h_0=2.2$[/tex] inches
K= 90,000 Psi
μ = 0.2, R = 14 inches, N = 150 rpm
For the maximum possible draft in one pass,
[tex]$\Delta h = H_0-h_f=\mu^2R$[/tex]
[tex]$=0.2^2 \times 14 = 0.56$[/tex] inches
[tex]$h_f = 2.2 - 0.56$[/tex]
= 1.64 inches
Roll strip contact length (L) = [tex]$\sqrt{R(h_0-h_f)}$[/tex]
[tex]$=\sqrt{14 \times 0.56}$[/tex]
= 2.8 inches
Absolute value of true strain, [tex]$\epsilon_T$[/tex]
[tex]$\epsilon_T=\ln \left(\frac{2.2}{1.64}\right) = 0.2937$[/tex]
Average true stress, [tex]$\overline{\gamma}=\frac{K\sum_f}{1+n}= 31305.56$[/tex] Psi
Roll force, [tex]$L \times b \times \overline{\gamma} = 2.8 \times 9 \times 31305.56$[/tex]
= 788,900 lb
For SI units,
Power = [tex]$\frac{2 \pi FLN}{60}$[/tex]
[tex]$=\frac{2 \pi 788900\times 2.8\times 150}{60\times 44.25\times 12}$[/tex]
= 10399.81168 W
Horse power = 13.9357
HELP! It’s for an architecture class on PLATO
Select the correct answer.
Which association maintains the International Building Code?
A. NFPA
B. ICC
C. EPA
D. DOJ
Answers
Answer:
ICC
Explanation:
The International Building Code (IBC) is a model building code developed by the International Code Council (ICC). It has been adopted for use as a base code standard by most jurisdictions in the United States.