Answer:
a scale model each size is a certain amount smaller
Explanation:
It describes the physical and social elements common to this work. Note that common contexts are listed toward the top, and less common contexts are listed toward the bottom. According to O*NET, what are common work contexts for Reporters and Correspondents? Check all that apply.
Answer:
Acef
Explanation:
Edginuity 2021
Answer:
2,3,4,5
Explanation:
guy above me is wrong
A 3-phase , 1MVA, 13.8kV/4160V, 60 Hz, transformer with Y-Delta winding connection is supplying a3-phase, 0.75 p.u. load on the 4160V side of the transformer. The load has leading power factor of 0.9. It issupplied by 1 p.u. voltage on the 13.8kV side. The transformer per unit impedance is j0.12 referred to thesecondary side.
a. Find the load impedance.
b. Find the input current on the primary side in real units.
c. Find the input power factor
Answer:
a) 23.89 < -25.84 Ω
b) 31.38 < 25.84 A
c) 0.9323 leading
Explanation:
A) Calculate the load Impedance
current on load side = 0.75 p.u
power factor angle = 25.84
[tex]I_{load}[/tex] = 0.75 < 25.84°
attached below is the remaining part of the solution
B) Find the input current on the primary side in real units
load current in primary = 31.38 < 25.84 A
C) find the input power factor
power factor = 0.9323 leading
attached below is the detailed solution
6. Find the heat flow in 24 hours through a refrigerator door 30.0" x 58.0" insulated with cellulose fiber 2.0" thick. The temperature inside the refrigerator is 38°F. Room temperature is 72°F. [answer in BTUs]
Answer:
The heat flow in 24 hours through the refrigerator door is approximately 1,608.57 BTU
Explanation:
The given parameters are;
The duration of the heat transfer, t = 24 hours = 86,400 seconds
The area of the refrigerator door, A = 30.0" × 58.0" = 1,740 in.² = 1.122578 m²
The material of the insulator in the door = Cellulose fiber
The thickness of the insulator in the door, d = 2.0" = 0.0508 m
The temperature inside the fridge = 38° F = 276.4833 K
The temperature of the room = 78°F = 298.7056 K
The thermal conductivity of cellulose fiber = 0.040 W/(m·K)
By Fourier's law, the heat flow through a by conduction material is given by the following formula;
[tex]\dfrac{Q}{t} = \dfrac{k \cdot A \cdot (T_2 - T_1) }{d}[/tex]
[tex]Q = \dfrac{k \cdot A \cdot (T_2 - T_1) }{d} \times t[/tex]
Therefore, we have;
[tex]Q = \dfrac{0.04 \times 1.122578 \times (298.7056 - 276.4833 ) }{0.0508} \times 86,400 =1,697,131.73522[/tex]
The heat flow in 24 hours through the refrigerator door, Q = 1,697,131.73522 J = 1,608.5705140685 BTU
Yeah order for a firm voltage dividers to operate properly The load resistance value should be at least Times greater than resistance value of the voltage divider bleeder resistor
Answer:
A voltage divider is a simple series resistor circuit. It's output voltage is a fixed fraction of its input voltage. The divide-down ratio is determined by two resistors.
Question 1: What is the power observed in the energy analyzer when the rated voltage(U1) is applied to the primary of the transformer, and there is no load at the secondary?
Question 2: Find the transformation ratio of the transformer using the values U1,U2 recorded in the experiment.
Question 3: Sketch the no-load operation graph of the transformer using the values U1, I2 and the values read in the energy analyzer.
Question 4: How can we find the number of turns of transformer?
Question 5: Explain the operation principle of the transformer.
Question 6: State your final observations about the experiment.
Answer:
preguntas a parte o no???????
A demand factor of _____ percent applies to a multifamily dwelling with ten units if the optional calculation method is used.
Some of our modern kitchen cookware is made of ceramic materials. (a) List at least three important characteristics required of a material to be used for this application. (b) Make a comparison of three ceramic materials as to their relative properties and, in addition, to cost. (c) On the basis of this comparison, select the material most suitable for the cookware.
Answer:
A)
It should be Non- toxic
It should possess high Thermal conductivity
It should have the Required Thermal diffusivity
B)
stoneware : This material has good thermal diffusivity and it is quite affordable and it is used in making pizza stonesporcelain: mostly used for mugs and it is non-toxic Pyrex : posses good thermal conductivity used in ovenC) All the materials are suitable because they serve different purposes when making modern kitchen cookware
Explanation:
A) characteristics required of a ceramic material to be used as a kitchen cookware
It should be Non- toxicIt should possess high Thermal conductivityIt should have the Required Thermal diffusivityB) comparison of three ceramic materials as to their relative properties
stoneware : This material has good thermal diffusivity and it is quite affordable and it is used in making pizza stonesporcelain: mostly used for mugs and it is non-toxic Pyrex : posses good thermal conductivity used in ovensC) material most suitable for the cookware.
All the materials are suitable because they serve different purposes when making modern kitchen cookware