Introduction, Electronic filters are critical components of electronic circuits. Their primary function is to pass signals with certain frequencies.
While blocking others. Electronic filters with NI my RIO refer to a class of electronic filters that are implemented using National Instruments my RIO hardware and software platform. In this literature survey, we will explore various aspects of electronic filters with NI my RIO.
We will provide background information on electronic filters, including their types, classifications, and applications. We will also discuss the NI my RIO platform and how it can be used to implement electronic filters. Furthermore, we will review some of the latest research and developments in the field of electronic filters with NI myRIO.
To know more about Electronic visit:
https://brainly.com/question/13224410
#SPJ11
(i) determine the transfer function from u to y; (ii) if the system is stable or not; (iii) Compute the location of the zeros and poles. d²x = -x + 4u, dy dt =y+x+u dt²
The problem statement is given as follows:d²x = -x + 4u, dy dt = y + x + u dt²In this problem statement, we have been asked to determine the transfer function from u to y, the stability of the system, and the location of the zeros and poles.
The transfer function from u to y is defined as the Laplace transform of the output variable y with respect to the input variable u, considering all the initial conditions to be zero. Hence, taking Laplace transforms of both sides of the given equations, we get: L{d²x} = L{-x + 4u}L{dy} = L{y + x + u}Hence, we get: L{d²x} = s²X(s) – sx(0) – x'(0) = -X(s) + 4U(s)L{dy} = sY(s) – y(0) = Y(s) + X(s) + U(s)where X(s) = L{x(t)}, Y(s) = L{y(t)}, and U(s) = L{u(t)}.On substituting the given initial conditions as zero, we get: X(s)[s² + 1] + 4U(s) = Y(s)[s + 1]By simplifying the above equation, we get: Y(s) = (4/s² + 1)U(s).
Therefore, the transfer function from u to y is given by: G(s) = Y(s)/U(s) = 4/s² + 1The system is stable if all the poles of the transfer function G(s) lie on the left-hand side of the s-plane.
To know more about transfer function visit:
https://brainly.com/question/31326455
#SPJ11
a 7. After a quality check, it can be ensured that a ceramic structural part has no surface defects greater than 25um. Calculate the maximum stress that may occur for silicon carbide (SIC) (Kic=3MPavm
The maximum stress that may occur for silicon carbide (SiC) can be calculated using the formula for maximum stress based on fracture toughness: σ_max = (K_ic * (π * a)^0.5) / (Y * c)
Where: σ_max is the maximum stress. K_ic is the fracture toughness of the material (3 MPa√m for SiC in this case). a is the maximum defect size (25 μm, converted to meters: 25e-6 m). Y is the geometry factor (typically assumed to be 1 for surface defects). c is the characteristic flaw size (usually taken as the crack length). Since the characteristic flaw size (c) is not provided in the given information, we cannot calculate the exact maximum stress. To determine the maximum stress, we would need the characteristic flaw size or additional information about the structure or loading conditions.
To know more about silicon carbide, visit
https://brainly.com/question/30148762
#SPJ11
4.28 What pressure gradient is required to accelerate kerosene (S = 0.81) vertically upward in a vertical pipe at a rate of 0.3 g?
The pressure gradient required to accelerate kerosene vertically upward in a vertical pipe at a rate of 0.3 g is calculated using the formula ΔP = ρgh.
Where ΔP is the pressure gradient, ρ is the density of the fluid (kerosene), g is the acceleration due to gravity, and h is the height. In this case, the acceleration is given as 0.3 g, so the acceleration due to gravity can be multiplied by 0.3. By substituting the known values, the pressure gradient can be determined. The pressure gradient can be calculated using the formula ΔP = ρgh, where ΔP is the pressure gradient, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the height. In this case, the fluid is kerosene, which has a specific gravity (S) of 0.81. Specific gravity is the ratio of the density of a substance to the density of a reference substance (usually water). Since specific gravity is dimensionless, we can use it directly as the density ratio (ρ/ρ_water). The acceleration is given as 0.3 g, so the effective acceleration due to gravity is 0.3 multiplied by the acceleration due to gravity (9.8 m/s²). By substituting the values into the formula, the pressure gradient required to accelerate the kerosene vertically upward can be calculated.
Learn more about pressure gradient here:
https://brainly.com/question/30463106
#SPJ11
Name the five (5) properties that determine the quality of a sand mold for sand casting? [5 Marks] Identify the five (5) important advantages of shape-casting processes.
1. List three situations in which the casting operation is the preferred fabrication technique from other manufacturing processes.
2. What is the difference between a pattern and a core in sand molding?
Give two reasons why turbulent flow of molten metal into the mold should be avoided?
Properties that determine the quality of a sand mold for sand casting are:1. Collapsibility: The sand in the mold should be collapsible and should not be very stiff. The collapsibility of the sand mold is essential for the ease of casting.
2. Permeability: Permeability is the property of the mold that enables air and gases to pass through.
Permeability ensures proper ventilation within the mold.
3. Cohesiveness: Cohesiveness is the property of sand molding that refers to its ability to withstand pressure without breaking or cracking.
4. Adhesiveness: The sand grains in the mold should stick together and not fall apart or crumble easily.
5. Refractoriness: Refractoriness is the property of sand mold that refers to its ability to resist high temperatures without deforming.
Advantages of Shape-casting processes:1. It is possible to create products of various sizes and shapes with casting processes.
2. The products created using shape-casting processes are precise and accurate in terms of dimension and weight.
3. With shape-casting processes, the products produced are strong and can handle stress and loads.
4. The production rate is high, and therefore, it is cost-effective.
Know more about Collapsibility here:
https://brainly.com/question/14131240
#SPJ11
Consider a substance that boils at -34°C (negative thirty four degrees Celsius) at 98 kPa. At that temperature and pressure, one kg of liquid occupies 0.0015 m³ and one kg of vapor occupies 1.16 m². At 80 kPa, this stuff boils at -38°C (negative thirty eight degrees Celsius). Using just this information: a. Estimate the enthalpy of vaporization of this substance at 98 kPa. (Hint: you can use either the Clapeyron Equation or the Claypeyron-Clausius Equation to solve (a)) b. Estimate the molar mass of the substance.
a. The estimated enthalpy of vaporization of the substance at 98 kPa can be calculated using the Clapeyron Equation or the Clapeyron-Clausius Equation.
b. The molar mass of the substance can be estimated using the ideal gas law and the given information.
a. To estimate the enthalpy of vaporization at 98 kPa, we can use either the Clapeyron Equation or the Clapeyron-Clausius Equation. These equations relate the vapor pressure, temperature, and enthalpy of vaporization for a substance. By rearranging the equations and substituting the given values, we can solve for the enthalpy of vaporization. The enthalpy of vaporization represents the energy required to transform one kilogram of liquid into vapor at a given temperature and pressure.
b. To estimate the molar mass of the substance, we can use the ideal gas law, which relates the pressure, volume, temperature, and molar mass of a gas. Using the given information, we can calculate the volume occupied by one kilogram of liquid and one kilogram of vapor at the specified conditions. By comparing the volumes, we can determine the ratio of the molar masses of the liquid and vapor. Since the molar mass of the vapor is known, we can then estimate the molar mass of the substance.
These calculations allow us to estimate both the enthalpy of vaporization and the molar mass of the substance based on the given information about its boiling points, volumes, and pressures at different temperatures. These estimations provide insights into the thermodynamic properties and molecular characteristics of the substance.
Learn more about Clapeyron Equation here:
https://brainly.com/question/33369944
#SPJ11
An ash disposal system of a steam plant cost $30,000 when new. It is now 4 years old. The
annual maintenance costs for the four years have been $2000, $2250, $2675, $3000.
Interest rate = 6%. A new system is guaranteed to have an equated annual maintenance and
operation cost not exceeding $1500. Its cost is $47,000 installed. Life of each system, 7
years; salvage value, 5% of the first cost. Present sale value of old system is same as salvage
value. Would it be profitable to install the new system?
To find out if it would be profitable to install the new ash disposal system, we will have to calculate the present value of both the old and new systems and compare them. Here's how to do it:Calculations: Salvage value = 5% of the first cost = [tex]5% of $30,000 = $1,500.[/tex]
Life of each system = 7 years. Interest rate = 6%.The annual maintenance costs for the old system are given as
[tex]$2000, $2250, $2675, $3000.[/tex]
The present value of the old ash disposal system can be calculated as follows:
[tex]PV = ($2000/(1+0.06)^1) + ($2250/(1+0.06)^2) + ($2675/(1+0.06)^3) + ($3000/(1+0.06)^4) + ($1500/(1+0.06)^5)PV = $8,616.22[/tex]
The present value of the new ash disposal system can be calculated as follows:
[tex]PV = $47,000 + ($1500/(1+0.06)^1) + ($1500/(1+0.06)^2) + ($1500/(1+0.06)^3) + ($1500/(1+0.06)^4) + ($1500/(1+0.06)^5) + ($1500/(1+0.06)^6) + ($1500/(1+0.06)^7) - ($1,500/(1+0.06)^7)PV = $57,924.73[/tex]
Comparing the present values, it is clear that installing the new system would be profitable as its present value is greater than that of the old system. Therefore, the new ash disposal system should be installed.
To know more about profitable visit :
https://brainly.com/question/15293328
#SPJ11
A first-order instrument with a time constant of 0.5 s is to be used to measure a periodic input. If a dynamic error of 12% can be tolerated, determine the maximum frequency of periodic inputs that can be measured; in Hz. Provide your answer using 3 decimal places.
The equation that will be used to determine the maximum frequency of periodic inputs that can be measured with a first-order instrument with a time constant of 0.5 s and a dynamic error of 12% is given below:
[tex]$$\% Overshoot =\\ \frac{100\%\ (1-e^{-\zeta \frac{\pi}{\sqrt{1-\zeta^{2}}}})}{(1-e^{-\frac{\pi}{\sqrt{1-\zeta^{2}}}})}$$[/tex]
Where [tex]$\zeta$[/tex] is the damping ratio.
We can derive an equation for [tex]$\zeta$[/tex] using the time constant as follows:
[tex]$$\zeta=\frac{1}{2\sqrt{2}}$$[/tex]
To find the maximum frequency of periodic inputs that can be measured we will substitute the values into the formula provided below:
[tex]$$f_{m}=\frac{1}{2\pi \tau}\sqrt{1-2\zeta^2 +\sqrt{4\zeta^4 - 4\zeta^2 +2}}$$[/tex]
Where [tex]$\tau$[/tex] is the time constant.
Substituting the values given in the question into the formula above yields;
[tex]$$f_{m}=\frac{1}{2\pi (0.5)}\sqrt{1-2(\frac{1}{2\sqrt{2}})^2 +\sqrt{4(\frac{1}{2\sqrt{2}})^4 - 4(\frac{1}{2\sqrt{2}})^2 +2}}$$$$=2.114 \text{ Hz}$$[/tex]
The maximum frequency of periodic inputs that can be measured with a first-order instrument with a time constant of 0.5 s and a dynamic error of 12% is 2.114 Hz. The calculation is based on the equation for the maximum frequency and the value of damping ratio which is derived from the time constant.
The damping ratio was used to calculate the maximum percentage overshoot that can be tolerated, which is 12%. The frequency that can be measured was then determined using the equation for the maximum frequency, which is given above. The answer is accurate to three decimal places.
Learn more about time constant here:
brainly.com/question/32577767
#SPJ11
2) A linear elastic SDOF system is given below with Tn= 1.1 s, m = 1 kg, 5 = 5 %, u(0) = 0, u(0) = 0. Determine the displacement response u(t) under the base excitation üç (t) defined below. Use At = 0.1 s in calculations. 0.6 U m i A oli 0,2 013 014 015 kc -0.4 Time (s)
Given values:Tn = 1.1 s, m = 1 kg, ξ = 5%, u(0) = 0, u'(0) = 0.At = 0.1 s
And base excitation üc(t) is given as below:
0.6 Umi sin (2πti) for 0 ≤ t ≤ 0.2 s0.2 sin (2π(501)(t - 0.2)) for 0.2 ≤ t ≤ 0.3 s-0.4 sin (2π(501)(t - 0.3)) for 0.3 ≤ t ≤ 0.4 sThe undamped natural frequency can be calculated as
ωn = 2π / Tnωn = 2π / 1.1ωn = 5.7 rad/s
The damped natural frequency can be calculated as
ωd = ωn √(1 - ξ²)ωd = 5.7 √(1 - 0.05²)ωd = 5.41 rad/s
The damping coefficient can be calculated as
k = m ξ ωnk = 1 × 0.05 × 5.7k = 0.285 Ns/m
The spring stiffness can be calculated as
k = mωd² - ξ²k = 1 × 5.41² - 0.05²k = 14.9 N/m
The general solution of the equation of motion is given by
u(t) = Ae^-ξωn t sin (ωd t + φ
)whereA = maximum amplitude = (1 / m) [F0 / (ωn² - ωd²)]φ = phase angle = tan^-1 [(ξωn) / (ωd)]
The maximum amplitude A can be calculated as
A = (1 / m) [F0 / (ωn² - ωd²)]A = (1 / 1) [0.6 Um / ((5.7)² - (5.41)²)]A = 0.2219
UmThe phase angle φ can be calculated astanφ = (ξωn) / (ωd)tanφ = (0.05 × 5.7) / (5.41)tanφ = 0.0587φ = 3.3°
Displacement response u(t) can be calculated as:for 0 ≤ t ≤ 0.2 s, the displacement response u(t) isu(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + 3.3°)for 0.2 ≤ t ≤ 0.3 s, the displacement response
u(t) isu(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t - 30.35°)for 0.3 ≤ t ≤ 0.4 s, t
he displacement response
u(t) isu(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + 57.55°)
Hence, the displacement response of the SDOF system under the base excitation is
u(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + φ) for 0 ≤ t ≤ 0.2 s, 0.2 ≤ t ≤ 0.3 s, and 0.3 ≤ t ≤ 0.4 s, whereφ = 3.3° for 0 ≤ t ≤ 0.2 su(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t - 30.35°) for 0.2 ≤ t ≤ 0.3 su(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + 57.55°) for 0.3 ≤ t ≤ 0.4 s. The response is plotted below.
To know more about frequency visit :
https://brainly.com/question/29739263
#SPJ11
The latent heat of vaporisation λ can be calculated by λ = 2.50025 - 0.002365T , with λ in MJ/kg and T in °C. Assuming the density of water is 1000kg/m³ and is constant, calculate the energy flux input required to evaporate 1mm of water in one hour when the temperature Tis 26°C. Present the result in the unit of W/m² and round to the nearest integer. Your Answer: Answer
Answer: 2441000.We need to calculate the energy flux input required to evaporate 1 mm of water in one hour.Energy flux input =[tex]λρl/h[/tex] where λ is the latent heat of vaporization, ρ is the density of water, l is the latent heat of vaporization per unit mass, and h is the time taken for evaporation.
We know that the density of water is 1000 kg/m³, and the latent heat of vaporization per unit mass is l = λ/m. Here m is the mass of water evaporated, which can be calculated as:m = ρVwhere V is the volume of water evaporated. Since the volume of water evaporated is 1 mm³, we need to convert it to m³ as follows:[tex]1 mm³ = 1×10⁻⁹ m³So,V = 1×10⁻⁹ m³m = ρV = 1000×1×10⁻⁹ = 1×10⁻⁶ kg[/tex]
Now, the latent heat of vaporization per unit mass [tex]isl = λ/m = λ/(1×10⁻⁶) MJ/kg[/tex]
We are given that the water evaporates in 1 hour or 3600 seconds.h = 3600 s
Energy flux input = [tex]λρl/h= (2.50025 - 0.002365T)×1000×(λ/(1×10⁻⁶))/3600[/tex]
=[tex](2.50025 - 0.002365×26)×1000×(2.5052×10⁶)/3600= 2.441×10⁶ W/m²[/tex]
Thus, the energy flux input required to evaporate 1mm of water in one hour when the temperature T is 26°C is [tex]2.441×10⁶ W/m²[/tex].
To know more about vaporization visit:-
https://brainly.com/question/30078883
#SPJ11
From the technical literature and/or open sources, present the RCS of the triangular trihedral reflector as a function of the incidence angle (for both azimuth and elevation).
The radar cross section (RCS) of the triangular trihedral reflector as a function of the incidence angle (for both azimuth and elevation) can be found from the technical literature and/or open sources.
A trihedral reflector is a corner reflector that consists of three mutually perpendicular planes.
Reflectivity is the measure of a surface's capability to reflect electromagnetic waves.
The RCS is a scalar quantity that relates to the ratio of the power per unit area scattered in a specific direction to the strength of an incident electromagnetic wave’s electric field.
The RCS formula is given by:
[tex]$$ RCS = {{4πA}\over{\lambda^2}}$$[/tex]
Where A is the projected surface area of the target,
λ is the wavelength of the incident wave,
RCS is measured in square meters.
In the case of a trihedral reflector, the reflectivity is the same for both azimuth and elevation angles and is given by the following equation:
[tex]$$ RCS = {{16A^2}\over{\lambda^2}}$$[/tex]
Where A is the surface area of the trihedral reflector.
RCS varies with the incident angle, and the equation above is used to compute the reflectivity for all incident angles.
Therefore, it can be concluded that the RCS of the triangular trihedral reflector as a function of the incidence angle (for both azimuth and elevation) can be determined using the RCS formula and is given by the equation :
[tex]$$ RCS = {{16A^2}\over{\lambda^2}}$$.[/tex]
To know more about Magnetic field, visit:
https://brainly.com/question/19542022
#SPJ11
In a simple gas turbine installation, the air pressure is 100kPa and 280K
temperature enters the compressor. Your maximum temperature
The heat given to the air per unit mass in the cycle where it is 1100K
It is 750kj.
A-) According to the Ideal Brayton Cycle
B-) 80% of turbine efficiency and 75% of compressor efficiency
pressures and temperatures at each point according to the cycle in which it is, and
Calculate the thermal efficiency.
C-) Calculate the entropy values produced for both cases
Draw the P-v and T-s diagrams.
A) According to the Ideal Brayton Cycle the maximum temperature is 1100K.
B) The Brayton cycle's thermal efficiency is expressed as η = (1 – (1/3.9285)) × (1 – (280/1100)) = 0.4792 = 47.92%.
C) Entropy values produced in the cycle: State 1: s1 = s0 + cp ln(T1/T0) = 0.3924; State 2: s2 = s1 = 0.3924; State 3: s3 = s2 + cp ln(T3/T2) = 0.6253; State 4: s4 = s3 = 0.6253.P-V and T-S.
A) Ideal Brayton Cycle:An ideal Brayton cycle consists of four reversible processes, namely 1-2 Isentropic compression, 2-3 Isobaric Heat Addition, 3-4 Isentropic Expansion, and 4-1 Isobaric Heat Rejection.The heat given to the air per unit mass in the cycle where it is 1100K is 750kJ.
So, in the first stage, Air enters the compressor at 280K temperature and 100 kPa pressure. The air is compressed isentropically to the highest temperature of 1100K.
Next, the compressed air is heated at a constant pressure of 1100K temperature and the heat addition process occurs at this point. In this process, the thermal efficiency is 1 – (1/r), where r is the compression ratio, which is equal to 1100/280 = 3.9285.
The next stage is isentropic expansion, where the turbine will produce work, and the gas will be cooled to a temperature of 400K.Finally, the gas passes through the heat exchanger where heat is rejected and the temperature decreases to 280K.
The Brayton cycle's thermal efficiency is expressed as η = (1 – (1/r)) × (1 – (T1/T3)) where T1 and T3 are absolute temperatures at the compressor inlet and turbine inlet, respectively.
Efficiency (η) = (1 – (1/3.9285)) × (1 – (280/1100)) = 0.4792 = 47.92%.
B) Efficiency:
Compressor efficiency (ηc) = 75%.
Turbine efficiency (ηt) = 80%.
The temperatures and pressures are:
State 1: p1 = 100 kPa, T1 = 280 K.
State 2: p2 = p3 = 3.9285 × 100 = 392.85 kPa. T2 = T3 = 1100 K.
State 4: p4 = p1 = 100 kPa. T4 = 400 K.
C) Entropy:
Entropy values produced in the cycle:
State 1: s1 = s0 + cp ln(T1/T0) = 0.3924.
State 2: s2 = s1 = 0.3924.
State 3: s3 = s2 + cp ln(T3/T2) = 0.6253.
State 4: s4 = s3 = 0.6253.P-V and T-S.
For more such questions on Brayton Cycle, click on:
https://brainly.com/question/18850707
#SPJ8
You have probably noticed warning signs on the highways stating that bridges may be icy even when the roads are not. Explain how this can happen. If the distance between the sun and the earth was the half of what it is L=0.5 x 1.496 x 1011 m, what would the solar constant be? The sun is a nearly spherical body that has a diameter of D = 1.393 x 109 m and the effective surface temperature of the sun is Tsun = 5778 K.
Bridges are more prone to icing due to their elevated position, exposure to cold air from below, and less insulation. If the distance between the sun and the Earth was halved, the solar constant would be quadrupled.
What factors contribute to bridges being more prone to icing compared to roads, and how would the solar constant change if the distance between the sun and the Earth was halved?Warning signs about icy bridges even when the roads are not icy can be attributed to several factors. Bridges are elevated structures that are exposed to the surrounding air from both above and below. This exposes the bridge surface to colder temperatures and airflow, making them more susceptible to freezing compared to the roads.
Bridges lose heat more rapidly than roads due to their elevated position, which allows cold air to circulate beneath them. This results in the bridge surface being colder than the surrounding road surface, even if the air temperature is above freezing. Additionally, bridges have less insulation compared to roads, as they are usually made of materials like concrete or steel that conduct heat more efficiently. This allows heat to escape more quickly, further contributing to the freezing of the bridge surface.
Furthermore, bridges often have different thermal properties compared to roads. They may have less sunlight exposure during the day, leading to slower melting of ice and snow. The presence of shadows and wind patterns around bridges can also create localized cold spots, making them more prone to ice formation.
Regarding the solar constant, which is the amount of solar radiation received per unit area at the outer atmosphere of the Earth, if the distance between the sun and the Earth was halved, the solar constant would be doubled. This is because the solar constant is inversely proportional to the square of the distance between the sun and the Earth. Therefore, halving the distance would result in four times the intensity of solar radiation reaching the Earth's surface.
The solar constant is calculated using the formula:
Solar Constant = (Luminosity of the Sun) / (4 * π * (Distance from the Sun)^2)
Given the diameter of the sun (D = 1.393 x 10^9 m), the effective surface temperature of the sun (Tsun = 5778 K), and the new distance between the sun and the Earth (L = 0.5 x 1.496 x 10^11 m), the solar constant can be calculated using the formula above with the new distance value.
Learn more about elevated position
brainly.com/question/30046587
#SPJ11
Find the current drawn by a 20 hp, 440 V three-phase motor operating at full load with 90% efficiency and 0.9 lagging power factor.
Calculate the values of P and Q consumed by the motor. (1 hp = 746 W)
A three-phase AC induction motor draws a current of 28.96 A at full load. The power consumed by the motor is 14.9 kW.
Given that the motor has 90% efficiency and a power factor of 0.9, the apparent power consumed by the motor is 16.56 kVA.
The formula to calculate power factor is
cosine(phi) = P/S = 746*20/(3*440*I*cosine(phi))
Therefore, the power factor = 0.9 or cos(phi) = 0.9
The real power P consumed by the motor is P = S * cosine(phi) or P = 16.56 kVA * 0.9 = 14.9 kW
The reactive power Q consumed by the motor is Q = S * sine(phi) or Q = 16.56 kVA * 0.4359 = 7.2 kVAR, where sine(phi) = sqrt(1 - cosine(phi)^2).
Thus, the current drawn by the motor is 28.96 A, and the power consumed by the motor is 14.9 kW. The values of P and Q consumed by the motor are 14.9 kW and 7.2 kVAR respectively.
To know more about power factor visit:
https://brainly.com/question/11957513
#SPJ11
Two normal stresses of equal magnitude of 5, but of opposite signs, act at an stress element in perpendicular directions x and y. The shear stress acting in the xy-plane at the plane is zero. The magnitude of the normal stress acting on a plane inclined at 45 deg to the x-axis.
O None of these
O 5/2
O 25
O 5/4
O 0
Given data: Normal stresses of equal magnitude = 5Opposite signs, Act at an stress element in perpendicular directions x and y.The shear stress acting in the xy-plane at the plane is zero. The plane is inclined at 45° to the x-axis.
Now, the normal stresses acting on the given plane is given by ;[tex]σn = (σx + σy)/2 + (σx - σy)/2 cos 2θσn = (σx + σy)/2 + (σx - σy)/2 cos 90°σn = (σx + σy)/2σx = 5σy = -5On[/tex]putting the value of σx and σy we getσn = (5 + (-5))/2 = 0Thus, the magnitude of the normal stress acting on a plane inclined at 45 deg to the x-axis is 0.Answer: The correct option is O 0.
To know more about plane visit:
https://brainly.com/question/2400767
#SPJ11
In absolute encoders, locations are always defined with respect to the origin of the axis system. True False
In absolute encoders, locations are always defined with respect to the origin of the axis system.False
Absolute encoders are a type of position sensing device used in various applications. Unlike relative encoders that provide incremental position information, absolute encoders provide the exact position of an object within a system. However, in absolute encoders, the locations are not always defined with respect to the origin of the axis system.
An absolute encoder generates a unique code or value for each position along the axis it is measuring. This code represents the absolute position of the object being sensed. It does not rely on any reference point or origin to determine the position. Instead, the encoder provides a distinct value for each position, which can be translated into a specific location within the system.
This is in contrast to a relative encoder, which determines the change in position relative to a reference point or origin. In a relative encoder, the position information is relative to a starting point, and the encoder tracks the changes in position as the object moves from that reference point.
Absolute encoders offer advantages in applications where it is crucial to know the exact position of an object at all times. They provide immediate feedback and eliminate the need for homing or referencing procedures. However, since they do not rely on an origin point, the locations are not always defined with respect to the origin of the axis system.
Learn more about Absolute encoders
brainly.com/question/31381602
#SPJ11
The size of this building is approximately 25 m long, 10 m wide, and 12 m high. Determine the possible maximum drag force while this old building is in the dry and wet seasons. The average wind velocity and the flow velocity in this area are 6 and 0.8 m/s, respectively. Specify the number of Cd with the reference or evidence here. Discuss about the problem that could be occurred when this building submerged underwater. a) in dry season b) partly submerged VAL JAG VAL c) mostly submerg
Drag force is a resistive force exerted on an object moving through a fluid, such as air or water. It opposes the object's motion and is proportional to the object's velocity and the fluid's density.
Given data: Size of building = 25 m x 10 m x 12 m = 3000 m³ Wind velocity = 6 m/sFlow velocity = 0.8 m/s
a) Dry season. In the dry season, there is no possibility of a drag force acting on the building because of the absence of water.
b) Partly submerged. When the building is partly submerged, then drag force F can be given as:
F = (1/2) x (density of water) x (velocity of water)² x Cd x A
Where, Cd = drag coefficient ,
A = area of the building
= 2(25x10) + 2(10x12) + 2(25x12)
= 850 m²
F = (1/2) x (1000) x (0.8)² x 1.2 x 850
F = 231,840 N (approx)
c) Mostly submerged. When the building is mostly submerged, then drag force F can be given as:
F = (1/2) x (density of water) x (velocity of water)² x Cd x A
Where, Cd = drag coefficient,
A = area of the building = 2(25x10) + 2(10x12) + 2(25x12)
= 850 m²
(the same as in b)
F = (1/2) x (1000) x (0.8)² x 1.1 x 850F = 198,264 N (approx)
Problem that could be occurred when this building submerged underwater:
When the building is submerged underwater, the drag force increases, which can cause structural instability, especially if it is not designed to withstand such forces.
In addition, the buoyancy of the building can change, and the weight can increase due to waterlogging, leading to the sinking of the building.
To know more about Drag force visit:
https://brainly.com/question/13385370
#SPJ11
Consider Stokes' first problem, but allow the plate velocity to be an arbitrary function of time, U(t). By differentiation, show that the shear stress Tyx = pôuloy obeys the same diffusion equation that the velocity does. Suppose the plate is moved in such a way as to produce a constant wall shear stress. Determine the plate velocity for this motion. Discuss the distribution of vorticity in this flow field; compare and contrast with Stokes’ first problem. Hint: At some point, you will have to calculate an integral like: ∫ [1 – erf(n)an ju- 0 This may be done using integration by parts. It may be helpful to note that eftc(n) – n*-1exp(-n2) for large n.
Differentiating the shear stress equation shows its connection to the velocity equation. Determining plate velocity and vorticity distribution depend on specific conditions.
By differentiating the shear stress equation Tyx = pμU(y,t), we can show that it satisfies the same diffusion equation as the velocity equation. This demonstrates the connection between the shear stress and velocity in the flow field.
When the plate is moved to produce a constant wall shear stress, the plate velocity can be determined by solving the equation that relates the velocity to the wall shear stress. This may involve performing linear calculations or integrations, such as the mentioned integral involving the error function.
The distribution of vorticity in this flow field, which represents the local rotation of fluid particles, will depend on the specific plate motion and boundary conditions. It is important to compare and contrast this distribution with Stokes' first problem, which involves a plate moving at a constant velocity. The differences in the velocity profiles and boundary conditions will result in different vorticity patterns between the two cases.
Learn more about Linear click here :brainly.com/question/30763902
#SPJ11
Q6
Question 6 Other tests: a) Nominate another family of tests which may be required on a completed fabrication? b) Two test methods for detecting surface flaws in a completed fabrication are?
Non-destructive testing and destructive testing are two types of tests that may be required on a completed fabrication. Liquid penetrant testing and magnetic particle testing are two test methods for detecting surface flaws in a completed fabrication. These tests should be conducted by qualified and competent inspectors to ensure that all aspects of the completed fabrication are in accordance with the relevant specifications and requirements.
a) After completing fabrication, another family of tests that may be required is destructive testing. This involves examining the quality of the weld, the condition of the material, and the material’s performance.
b) Two test methods for detecting surface flaws in a completed fabrication are liquid penetrant testing and magnetic particle testing.Liquid Penetrant Testing (LPT) is a non-destructive testing method that is used to find surface cracks, flaws, or other irregularities on the surface of materials. The surface is cleaned, a penetrant is added, and excess penetrant is removed.
A developer is added to draw the penetrant out of any cracks, and the developer dries, highlighting the crack.Magnetic Particle Testing (MPT) is another non-destructive testing method that is used to find surface cracks and flaws on the surface of ferromagnetic materials. A magnetic field is generated near the material’s surface, and iron oxide particles are spread over the surface. These particles gather at areas where the magnetic field is disturbed, highlighting the crack, flaw, or discontinuity. These tests should be conducted by qualified and competent inspectors to ensure that all aspects of the completed fabrication are in accordance with the relevant specifications and requirements.
Explanation:There are different types of tests that may be required on a completed fabrication. One of these tests is non-destructive testing, which includes examining the quality of the weld, the condition of the material, and the material's performance. Destructive testing is another type of test that may be required on a completed fabrication, which involves breaking down the product to examine its structural integrity. Two test methods for detecting surface flaws in a completed fabrication are liquid penetrant testing and magnetic particle testing.
Liquid Penetrant Testing (LPT) is a non-destructive testing method that is used to find surface cracks, flaws, or other irregularities on the surface of materials. Magnetic Particle Testing (MPT) is another non-destructive testing method that is used to find surface cracks and flaws on the surface of ferromagnetic materials.
To know more about magnetic visit:
brainly.com/question/3617233
#SPJ11
A positive-sequence three-phase balanced wye voltage source has a phase voltage of Van=240/90° Vrms. Determine the line voltages of the source. ;
WRITE YOUR ANSWERS HERE: Vab_____________; Vbc_____________;Vca___________
Vab = 240/90° Vrms
Vbc = -120 + 207.85j Vrms
Vca = -120 - 207.j Vrms
To determine the line voltages of the source, we can use the following equations:
Vab = Van
Vbc = Van * e^(j120°)
Vca = Van * e^(-j120°)
where j is the imaginary unit.
Substituting the given value of Van = 240/90° Vrms, we get:
Vab = 240/90° Vrms
Vbc = (240/90° Vrms) * e^(j120°) = -120 + 207.85j Vrms
ca = (240/90° Vrms) * e^(-j120°) = -120 - 207.85j Vrms
Therefore, the line voltages of the source are:
Vab = 240/90° Vrms
Vbc = -120 + 207.85j Vrms
Vca = -120 - 207.j Vrms
To know more about imaginary unit, visit:
https://brainly.com/question/14820640
#SPJ11
Question 3 1 Point With a concentrated load P applied at the free end of a cantilever beam with length L, which of the following formula can be used to calculate maximum deflection? PL² BE PL3 BEI PL
The formula that can be used to calculate the maximum deflection (δ) of a cantilever beam with a concentrated load P applied at the free end is: δ = PL³ / (3EI).
This formula is derived from the Euler-Bernoulli beam theory, which provides a mathematical model for beam deflection.
In the formula,
δ represents the maximum deflection,
P is the magnitude of the applied load,
L is the length of the beam,
E is the modulus of elasticity of the beam material, and
I is the moment of inertia of the beam's cross-sectional shape.
The modulus of elasticity (E) represents the stiffness of the beam material, while the moment of inertia (I) reflects the resistance to bending of the beam's cross-section. By considering the applied load, beam length, material properties, and cross-sectional shape, the formula allows us to calculate the maximum deflection experienced by the cantilever beam.
It is important to note that the formula assumes linear elastic behavior and small deflections. It provides a good estimation for beams with small deformations and within the limits of linear elasticity.
To calculate the maximum deflection of a cantilever beam with a concentrated load at the free end, the formula δ = PL³ / (3EI) is commonly used. This formula incorporates various parameters such as the applied load, beam length, flexural rigidity, modulus of elasticity, and moment of inertia to determine the maximum deflection.
To know more about deflection, visit:
https://brainly.com/question/1581319
#SPJ11
(a) Before cutting or welding with oxy-acetylene gas welding or electric arc equipment, it is very important to check for signs of damage to the key components of each system. Name three items to check for oxy-acetylene gas welding and three items for electric arc equipment. These items must relate to the actual equipment being used by a technician in the performance of the welding task (joining of metals). (b) How would you check for gas leaks on oxy-acetylene welding equipment?
Before cutting or welding with oxy-acetylene gas welding or electric arc equipment, it is very important to check for signs of damage to the key components of each system.
Name three items to check for oxy-acetylene gas welding and three items for electric arc equipment. These items must relate to the actual equipment being used by a technician in the performance of the welding task (joining of metals).Checking for damage on oxy-acetylene gas welding equipment is critical to the process. As a result, the following three items should be inspected:
1. Oxygen and acetylene tanks, regulators, and hoses.
2. Gas torch handle and tip.
3. Lighting mechanism.
Electric arc equipment is similarly important to inspect for damage. As a result, the following three items should be inspected:
1. Cables and wire feed.
2. Electrodes and holders.
3. Torch and nozzles.
As for the second question, you would check for gas leaks on oxy-acetylene welding equipment by performing the following steps:
Step 1: With the equipment turned off, conduct a visual inspection of hoses, regulators, and torch connections for any damage.
Step 2: Regulators should be closed, hoses disconnected, and the torch valves shut before attaching the hoses to the tanks.
Step 3: Turning the acetylene gas on first and adjusting the regulator's pressure, then turning the oxygen on and adjusting the regulator's pressure, is the next step. Then turn the oxygen on and set the regulator's pressure.
Step 4: Open the torch valves carefully, adjusting the oxygen and acetylene valves until the flame is at the desired temperature. Keep an eye on the flame's color.
Step 5: When you're finished welding, turn off the valves on the torch, followed by the regulator valves.
To know more about oxy-acetylene visit:
https://brainly.com/question/28916568
#SPJ11
Orthogenal culting experiments vere conducted on a steel block under the folloring condilion Depth of cut t0- 0,13 min Width of eut −2.5 mm Rake angle −5^θ an Cultings speed - 2 m/s If the experimental observation results in chip thickness of 0.58 mm, cutting force of 890 N and Thrust force of 800N, determine the shear angle, coefficient of friction, shear stress and shear strain on the shear strain on the shear plane, Estimate the temperature rise if the flow strength of steel is 325 MPa, and thermal diffusivity is 14m²/s and volumetric specific heat is 3.3 N/mm°C
Shear angle: 8.46°, coefficient of friction: 0.118, shear stress: 971.03 MPa, shear strain: 0.219, and estimated temperature rise: 7.25 °C.
To calculate the shear angle (φ), we can use the formula:
φ = tan^(-1)((t0 - tc) / (wc * sin(θ)))
where t0 is the chip thickness, tc is the uncut chip thickness, wc is the width of cut, and θ is the rake angle. Plugging in the values, we get:
φ = tan^(-1)((0.58 mm - 0.13 mm) / (2.5 mm * sin(-5°)))
≈ 8.46°
To calculate the coefficient of friction (μ), we can use the formula:
μ = (Fc - Ft) / (N * sin(φ))
where Fc is the cutting force, Ft is the thrust force, and N is the normal force. Plugging in the values, we get:
μ = (890 N - 800 N) / (N * sin(8.46°))
≈ 0.118
To calculate the shear stress (τ) on the shear plane, we can use the formula:
τ = Fc / (t0 * wc)
Plugging in the values, we get:
τ = 890 N / (0.58 mm * 2.5 mm)
≈ 971.03 MPa
To calculate the shear strain (γ), we can use the formula:
γ = tan(φ) + (1 - tan(φ)) * (π / 2 - φ)
Plugging in the value of φ, we get:
γ ≈ 0.219
To estimate the temperature rise (ΔT), we can use the formula:
ΔT = (Fc * (t0 - tc) * K) / (A * γ * sin(φ))
where K is the flow strength, A is the thermal diffusivity, and γ is the shear strain. Plugging in the values, we get:
ΔT = (890 N * (0.58 mm - 0.13 mm) * 325 MPa) / (14 m^2/s * 0.219 * sin(8.46°))
≈ 7.25 °C
Therefore, the shear angle is approximately 8.46°, the coefficient of friction is approximately 0.118, the shear stress is approximately 971.03 MPa, the shear strain is approximately 0.219, and the estimated temperature rise is approximately 7.25 °C.
To learn more about temperature click here
brainly.com/question/7510619
#SPJ11
Quin-Bode Mat The forward path wander action of a uniry feedback control system is: 140 G(s) = s(s+15) Analytically determine the resonant peak My, resonant frequency or, and budwidth BW the chualpsystem
A uniry feedback control system has a forward path wander action, which is determined analytically. The given equation for a uniry feedback control system is 140 G(s) = s(s+15).
We need to find the resonant peak My, resonant frequency or, and bandwidth BW. The transfer function of the uniry feedback control system is: G(s) = s(s + 15)/140The resonant peak occurs at the frequency where the absolute value of the transfer function is maximum.
Thus, we need to find the maximum value of |G(s)|.Let's find the maximum value of the magnitude of the transfer function |G(s)|:|G(s)| = |s(s+15)|/140This will be maximum when s = -7.5So, |G(s)|max = |-7.5*(7.5+15)|/140= 84.375/140= 0.602Let's now find the frequency where this maximum value occurs.
To know more about system visit:
https://brainly.com/question/19843453
#SPJ11
A steel block [E = 29 x 103 ksi and v = 0.33] has initial side lengths all equal to 56 inches. After stresses are applied in the x, y, and a directions, the new lengths in the x, y, and z directions are 56.06 in., 56.10 in., and 55.95 in., respectively. Determine the stress components Ox, Oy, and o, that cause these deformations.
The stress components Ox, Oy, and Oz that cause these deformations are Ox = 2.07 ksi, Oy = 3.59 ksi, and Oz = -2.06 ksi, respectively.
Given information:
Young's modulus of elasticity, E = 29 x 103 ksi
Poisson's ratio, ν = 0.33
Initial length of the block, a = b = c = 56 inches
Change in the length in the x-direction, ΔLx = 0.06 inches
Change in the length in the y-direction, ΔLy = 0.10 inches
Change in the length in the z-direction, ΔLz = -0.05 inches
To determine the stress components Ox, Oy, and Oz that cause these deformations, we'll use the following equations:ΔLx = aOx / E (1 - ν)ΔLy = bOy / E (1 - ν)ΔLz = cOz / E (1 - ν)
where, ΔLx, ΔLy, and ΔLz are the changes in the length of the block in the x, y, and z directions, respectively.
ΔLx = 0.06 in.= a
Ox / E (1 - ν)56.06 - 56 = 56
Ox / (29 x 103)(1 - 0.33)
Ox = 2.07 ksi
ΔLy = 0.10 in.= b
Oy / E (1 - ν)56.10 - 56 = 56
Oy / (29 x 103)(1 - 0.33)
Oy = 3.59 ksi
ΔLz = -0.05 in.= c
Oz / E (1 - ν)55.95 - 56 = 56
Oz / (29 x 103)(1 - 0.33)
Oz = -2.06 ksi
Know more about components here:
https://brainly.com/question/31044183
#SPJ11
Choose the correct statement for the flow inside tube
The viscus effects and velocity changes are significant in boundary layer conditions.
Velocity is maximum at r= (2/3) R where R is maximum radial distance from pipe wall.
In Fully developed flow velocity is function of both r and x.
All of the above
Q2-Select the true statement.
Both Convection and conduction modes of heat transfer may involve in heat exchangers
Chemical depositions may increase heat transfer
LMTD Method can predict outlet temperatures in heat exchangers
Option A and B
Option A and C
Q3-
What is true about flow inside tube?
The pressure loss ΔP is inversely proportional to diameter
Head loss(hL) is proportional to pressure differential
The pressure loss ΔP is proportional to diameter
Both A and B
Both B and C
None
All of the above The correct statement for the flow inside tube is "All of the above".
Explanation:The flow inside the tube is characterized by different effects. The viscous effects and velocity changes are significant in boundary layer conditions. Velocity is maximum at r= (2/3) R where R is the maximum radial distance from the pipe wall. In Fully developed flow velocity is a function of both r and x. Hence all the given statements are true for the flow inside the tube.Q2. Option A and BThe true statements are "Both Convection and conduction modes of heat transfer may involve in heat exchangers" and "Chemical depositions may increase heat transfer".Explanation:Both the convection and conduction modes of heat transfer may involve in heat exchangers. Chemical depositions may increase heat transfer. Hence, option A and B are the true statements.Q3. Both B and CThe true statement is "Both B and C".Explanation:The pressure loss ΔP is proportional to diameter. Head loss(hL) is proportional to pressure differential. Hence, both statements B and C are true.
Learn more about velocity brainly.com/question/30559316
#SPJ11
Water at 20◦C flows in a 9 cm diameter pipe under fully
developed conditions. Since the velocity in the pipe axis is 10m/s,
calculate (a) Q, (b)V, (c) wall stress and (d) ∆P for 100m pipe
length.
To calculate the values requested, we can use the following formulas:
(a) Q (flow rate) = A × V
(b) V (average velocity) = Q / A
(c) Wall stress = (ρ × V^2) / 2
(d) ΔP (pressure drop) = wall stress × pipe length
Given:
- Diameter of the pipe (d) = 9 cm = 0.09 m
- Velocity of water flow (V) = 10 m/s
- Pipe length (L) = 100 m
- Density of water (ρ) = 1000 kg/m³ (approximate value)
(a) Calculating the flow rate (Q):
A = π × (d/2)^2
Q = A × V
Substituting the values:
A = π × (0.09/2)^2
Q = π × (0.09/2)^2 × 10
(b) Calculating the average velocity (V):
V = Q / A
Substituting the values:
V = Q / A
(c) Calculating the wall stress:
Wall stress = (ρ × V^2) / 2
Substituting the values:
Wall stress = (1000 × 10^2) / 2
(d) Calculating the pressure drop:
ΔP = wall stress × pipe length
Substituting the values:
ΔP = (ρ × V^2) / 2 × L
using the given values we obtain the final results for (a) Q, (b) V, (c) wall stress, and (d) ΔP.
Learn more about flow rate on:
brainly.com/question/24307474
#SPJ11
Using the thermodynamic data tables, estimate the heat capacity of liquid kJ Refrigerant HCFC-123 in units of kJ/kg.K C =
The heat capacity of liquid HCFC-123 is estimated to be X kJ/kg.K, based on thermodynamic data tables.
To estimate the heat capacity of liquid HCFC-123, we can refer to thermodynamic data tables. These tables provide information about the specific heat capacity of substances at different temperatures. The specific heat capacity (C) is defined as the amount of heat energy required to raise the temperature of a unit mass of a substance by one degree Kelvin (or Celsius).
In the case of HCFC-123, the specific heat capacity can be determined by looking up the appropriate values in the thermodynamic data tables. These tables typically provide values for specific heat capacity at various temperatures. By interpolating or extrapolating the data, we can estimate the specific heat capacity at a desired temperature range.
It's important to note that the specific heat capacity of a substance can vary with temperature. The values provided in the thermodynamic data tables are typically valid within a certain temperature range. Therefore, the estimated heat capacity of liquid HCFC-123 should be considered as an approximation within the specified temperature range.
To learn more about thermodynamic click here: brainly.com/question/32658141
#SPJ11
The heat capacity of liquid HCFC-123 is estimated to be X kJ/kg.K, based on thermodynamic data tables.
To estimate the heat capacity of liquid HCFC-123, we can refer to thermodynamic data tables. These tables provide information about the specific heat capacity of substances at different temperatures.
The specific heat capacity (C) is defined as the amount of heat energy required to raise the temperature of a unit mass of a substance by one degree Kelvin (or Celsius).
In the case of HCFC-123, the specific heat capacity can be determined by looking up the appropriate values in the thermodynamic data tables. These tables typically provide values for specific heat capacity at various temperatures. By interpolating or extrapolating the data, we can estimate the specific heat capacity at a desired temperature range.
It's important to note that the specific heat capacity of a substance can vary with temperature. The values provided in the thermodynamic data tables are typically valid within a certain temperature range.
Therefore, the estimated heat capacity of liquid HCFC-123 should be considered as an approximation within the specified temperature range.
To know more about data click here
brainly.com/question/11941925
#SPJ11
A silicon solar cell is fabricated by ion implanting arsenic into the surface of a 200 um thick p-type wafer with an acceptor density of 1x10l4 cm. The n-type side is 1 um thick and has an arsenic donor density of 1x10cm? Describe what happens to electrons generated outside of the depletion region on the p-type side, which comprises most of the volume of a silicon solar cell. Do they contribute to photocurrent?
some of the electrons produced outside the depletion region on the p-type side of a silicon solar cell can contribute to the photocurrent, but it is preferable to keep recombination losses to a minimum.
The depletion region is a type of p-n junction in the p-type semiconductor. It is created when an n-type semiconductor is joined with a p-type semiconductor.
The diffusion of charge carriers causes a depletion of charges, resulting in a depletion region.
A silicon solar cell is created by ion implanting arsenic into the surface of a 200 um thick p-type wafer with an acceptor density of 1x10l4 cm.
The n-type side is 1 um thick and has an arsenic donor density of 1x10cm. Electrons produced outside the depletion region on the p-type side are referred to as minority carriers. The majority of the volume of a silicon solar cell is made up of the p-type side, which has a greater concentration of impurities than the n-type side.As a result, the majority of electrons on the p-type side recombine with holes (p-type carriers) to generate heat instead of being used to generate current. However, some of these electrons may diffuse to the depletion region, where they contribute to the photocurrent.
When photons are absorbed by the solar cell, electron-hole pairs are generated. The electric field in the depletion region moves the majority of these electron-hole pairs in opposite directions, resulting in a current flow.
The process of ion implantation produces an n-type layer on the surface of the p-type wafer. This n-type layer provides a separate path for minority carriers to diffuse to the depletion region and contribute to the photocurrent.
However, it is preferable to minimize the thickness of this layer to minimize recombination losses and improve solar cell efficiency.
As a result, some of the electrons produced outside the depletion region on the p-type side of a silicon solar cell can contribute to the photocurrent, but it is preferable to keep recombination losses to a minimum.
To know more about acceptor visit;
brainly.com/question/30651241
#SPJ11
A diffracted x-ray beam is observed from an unknown cubic metal at angles 33.4558°, 48.0343°, θA, θB, 80.1036°, and 89.6507° when x-ray of 0.1428 nm wavelength is used. θA and θB are the missing third and fourth angles respectively. (a) Determine the crystal structure of the metal. (b) Determine the indices of the planes (hkl) that produce each of the peaks.
(c) Calculate the interplanar spacing (in nm) of the metal using the sixth diffracted angle, 89.6507° (d) Calculate the lattice parameter (in nm) of the metal using the sixth diffracted angle, 89.6507° (e) Identify the material. (f) Using the above results, calculate the angles of θA and θB.
A diffracted X-ray beam is observed from an unknown cubic metal at angles 33.4558°, 48.0343°, θA, θB, 80.1036°, and 89.6507° when X-ray of 0.1428 nm wavelength is used.
θA and θB are the missing third and fourth angles respectively. Crystal Structure of the Metal: For cubic lattices, d-spacing between (hkl) planes can be calculated by using Bragg’s Law. The formula to calculate d-spacing is given by nλ = 2d sinθ where n = 1, λ = 0.1428 nm Here, d = nλ/2 sinθ = (1×0.1428×10^-9) / 2 sin θ
The values of sin θ are calculated as: sin 33.4558° = 0.5498, sin 48.0343° = 0.7417, sin 80.1036° = 0.9828, sin 89.6507° = 1θA and θB are missing, which means we will need to calculate them first. For the given cubic metal, the diffraction pattern is of type FCC (Face-Centered Cubic) which means that the arrangement of atoms in the crystal structure of the metal follows the FCC pattern.
To know more about wavelength visit:
https://brainly.com/question/31143857
#SPJ11
solve Maximize Z = 15 X1 + 12 X2
s.t 3X1 + X2 <= 3000 X1+x2 <=500 X1 <=160 X2 >=50 X1-X2<=0
Maximize Z = 15 X1 + 12 X2 subject to the following constraints:3X1 + X2 ≤ 3000X1+x2 ≤ 500X1 ≤ 160X2 ≥ 50X1-X2 ≤ 0Solution:We need to maximize the value of Z = 15X1 + 12X2 subject to the given constraints.3X1 + X2 ≤ 3000, This constraint can be represented as a straight line as follows:X2 ≤ -3X1 + 3000.
This line is shown in the graph below:X1+x2 ≤ 500, This constraint can be represented as a straight line as follows:X2 ≤ -X1 + 500This line is shown in the graph below:X1 ≤ 160, This constraint can be represented as a vertical line at X1 = 160. This line is shown in the graph below:X2 ≥ 50, This constraint can be represented as a horizontal line at X2 = 50. This line is shown in the graph below:X1-X2 ≤ 0, This constraint can be represented as a straight line as follows:X2 ≥ X1This line is shown in the graph below: We can see that the feasible region is the region that is bounded by all the above lines. It is the region that is shaded in the graph below: We need to maximize Z = 15X1 + 12X2 within this region.
To know more about maximize visit:
https://brainly.com/question/30072001
#SPJ11