If VR is 10 V and VL is 10 V in a series RL circuit, the source voltage equals _____________ . a. 14.14 V b. 28.28 V c. 10 V d. 20 V

To calculate the value of self-inductance (L) needed for an RL circuit with a desired time constant and a given resistor value, we can use the formula: Time constant (τ) = L / R

Rearranging the formula, we can solve for L:
L = τ * R
Given that the desired time constant (τ) is 5 s and the resistor value (R) is 540 Ω, we can substitute these values into the formula to calculate the required self-inductance (L):
L = 5 s * 540 ΩL = 2700 H
Therefore, a self-inductance of 2700 henries (H) is needed to construct the RL circuit with a time constant of 5 s and a 540 Ω resistor.

To know more about self-inductance, click here https://brainly.com/question/31394359

#SPJ11

The velocity of the first sphere will be 0.9899m/s

We know that Potential Energy, P.E. will be:

P.E. = mgh

where m = 0.1 kg

g =  9.8 m/s^2

h = 0.05 m

On  substituting values we get,

P.E. = 0.1 * 9.8 * 0.05 = 0.049 J

By the law of conservation of Energy,

P.E. = K.E,

K.E. = Kinetic energy ,

[tex]K.E. =\frac{mv^{2} }{2}[/tex]

on substituting values we get,

(0.1 * v^2 *)/2 = 0.049

v^2 = 0.98

taking square root on both sides, we get

v = 0.9899 m/s

Therefore, the velocity of the first sphere will be 0.9899m/s.

to learn more about velocity :

https://brainly.com/question/30559316?referrer=searchResults

The total potential on the x-axis is zero.

To find the total potential on the x-axis, we need to calculate the potential due to each charge and then add them. The potential due to a point charge can be calculated using the equation V=kq/r, where V is the potential, k is Coulomb's constant, q is the charge, and r is the distance from the charge. Since the charges are on the x-axis, we can assume that the distance from each charge to any point on the x-axis is the absolute value of their respective x-coordinates. Using this equation, we can calculate that the potential due to the positive charge is 0.5k and the potential due to the negative charge is -0.8k. Adding these potentials gives us a total potential of -0.3k, which is zero when rounded to one decimal place. Therefore, the total potential on the x-axis is zero.

Learn more about Coulombs here.

brainly.com/question/15167088

#SPJ11

The purpose of crumple zones in spring-loaded trolleys or vehicles, also known as energy-absorbing zones, is to enhance occupant safety during a collision. Crumple zones are strategically designed sections of the vehicle that are engineered to deform or crumple upon impact.

Here are the main purposes of crumple zones:

1. Energy Absorption: Crumple zones are specifically designed to absorb and dissipate the kinetic energy generated during a collision. By deforming and crumpling, they help to slow down the deceleration experienced by the occupants of the vehicle, reducing the impact forces transferred to them.

2. Vehicle Structural Integrity: Crumple zones play a crucial role in preserving the structural integrity of the passenger compartment. By absorbing the impact energy, they help to minimize the damage to the cabin area, which is the space where occupants are seated. This protective function helps to maintain the survival space and protects the occupants from intrusion or serious injuries.

3. Occupant Protection: By extending the collision duration through controlled deformation, crumple zones help to mitigate the forces exerted on the occupants. Slowing down the deceleration allows for a more gradual and controlled transfer of energy, reducing the risk of severe injuries, such as whiplash, head trauma, or internal organ damage.

4. Redistribution of Forces: Crumple zones are designed to redirect and distribute the forces of impact away from the occupant compartment. They help to steer the impact forces towards less critical areas of the vehicle structure, such as the front or rear ends, where the energy can be absorbed and dissipated more effectively.

Overall, the inclusion of crumple zones in spring-loaded trolleys or vehicles aims to improve occupant safety by reducing the severity of collisions and minimizing the risk of injuries. These zones are an essential part of modern vehicle safety design.

To know more about crumple zones here

https://brainly.com/question/31840966

#SPJ4

While riding an amusement park ride, where you are strapped to the inside of a rapidly rotating giant metal wheel, your acceleration involves two components: centripetal acceleration and tangential acceleration.

Centripetal acceleration is the inward acceleration that keeps you moving in a circular path. It is directed towards the center of the circle and depends on the wheel's radius and your speed. The formula for centripetal acceleration is a_c = v^2/r, where 'a_c' is centripetal acceleration, 'v' is your speed, and 'r' is the radius of the wheel.

Tangential acceleration occurs if the wheel's rotational speed changes, causing you to speed up or slow down. Tangential acceleration is given by the formula a_t = r * α, where 'a_t' is tangential acceleration, 'r' is the radius of the wheel, and 'α' is the angular acceleration.

In summary, when riding a rapidly rotating amusement park ride, your acceleration consists of centripetal acceleration, which keeps you on a circular path, and tangential acceleration, which accounts for changes in rotational speed.

you know more about amusement park ride pls visit-

https://brainly.com/question/22823882

#SPJ11

Each 150 W incandescent lamp draws a current of 500 A when connected to a 120 V source.

To find the current drawn by each lamp, we can use the equation:

Power (P) = Voltage (V) x Current (I)

First, we need to convert the power of each lamp from watts to kilowatts:

150 W = 0.15 kW

Since there are 60 kW of illumination required, the number of lamps needed can be found by:

Number of lamps = 60 kW / 0.15 kW per lamp = 400 lamps

Now, we can find the current drawn by each lamp using the equation above:

60 kW = 120 V x I

I = 60,000 W / 120 V = 500 A

To learn more about current click on,

https://brainly.com/question/28110700

#SPJ4

The radius of gyration is a term used in physics that describes how the mass of an object is distributed around its center of mass. In this question, we are given two bodies, A and B, that have equal masses. However, the value of kA, the radius of gyration of body A, is twice that of kB, the radius of gyration of body B.

To determine the moment of inertia of body A, we can use the formula IA = kA2m, where m is the mass of the body. Similarly, for body B, the moment of inertia can be calculated using the formula IB = kB2m.

Substituting the given values, we get IA = 4IB. Therefore, option (d) IA = (1/4)1B is the correct answer.

It is important to note that the moment of inertia is a physical quantity that measures the resistance of an object to rotational motion around an axis. It depends on the distribution of mass around the axis of rotation. In this question, the difference in the radius of gyration of the two bodies implies that the mass is distributed differently in the two objects, even though they have the same mass.

To know more about moment of inertia click this link -

brainly.com/question/15246709

#SPJ11

Newton's third law of motion states that for every action, there is an equal and opposite reaction. This means that when an object applies a force on another object, the second object applies an equal force back on the first object in the opposite direction.

Newton's third law of motion is a fundamental principle of physics that describes the relationship between forces acting on objects. It states that when one object exerts a force on another object, the second object exerts an equal and opposite force back on the first object. This principle applies to all interactions between objects, whether they are at rest or in motion. The forces described by Newton's third law always come in pairs and act in opposite directions. This means that if an object A applies a force on an object B, object B applies an equal and opposite force on object A. Newton's third law of motion is important in many areas of physics, including mechanics, electromagnetism, and thermodynamics, and is a key concept in understanding how the universe works.

Learn more about thermodynamics : brainly.com/question/21858980

#SPJ11

The required value of the capacitor C is approximately 1.36 μF. to achieve a phase angle of zero between the current andcvoltage in the circuit, the reactance of the capacitor Xc and the reactance of the coil XL should be equal and opposite.

The reactance of the coil can be calculated as XL = 2πfL, where f is the frequency of the source voltage and L is the inductance of the coil. Substituting the given values, XL = 2π x 1360 x 0.13 = 115.64 Ω. The reactance of the capacitor is Xc = 1/(2πfC), where C is the capacitance of the capacitor. Equating Xc and XL and solving for C gives C ≈ 1.36 μF.

Learn more about voltage here:

https://brainly.com/question/13521443

#SPJ11

Hi! The term you're looking for is "displacement." Displacement refers to the amount of fluid a pump can move in one revolution. This is an important characteristic to consider when selecting a pump for a specific application, as it helps determine the overall efficiency and performance of the pump.

know more about displacement here https://brainly.com/question/30923109

#SPJ11

Electromagnetic radiation is a type of energy that travels through space in the form of waves. The different types of electromagnetic radiation are classified based on their frequency and wavelength. The frequency of electromagnetic radiation refers to the number of waves that pass a given point in a second, and it is measured in Hertz (Hz).

The types of electromagnetic radiation with the shortest frequency are gamma rays. Gamma rays have the highest frequency, ranging from 10^19 Hz to more than 10^24 Hz. They have the shortest wavelength and the highest energy among all electromagnetic radiation. Gamma rays are produced by the decay of atomic nuclei and in nuclear reactions. They are also produced by astronomical objects such as pulsars, supernovas, and black holes.

Gamma rays are extremely dangerous and can be harmful to living organisms. They can ionize atoms and molecules, which can damage DNA and cause mutations, cancer, and other health problems. Therefore, it is important to shield ourselves from gamma rays by using protective equipment and following safety protocols when working with sources of ionizing radiation.

To Learn more about Electromagnetic radiation. Click this!

brainly.com/question/15320170

#SPJ11

Answer:

274.4 meters

Explanation:

As speed = distance/time, we can customize this formula to speed = distance*2/time, as its and echo it travels to the object and comes back to the place where the sound came from travelling that distance twice.

So, speed = distance*2/time

      343 = 2x/1.6

      343*1.6= 2x

         548.8= 2x

          x = 274.4 meters

The flux passing through the cylinder can be calculated using the formula for flux in cylindrical coordinates, which involves integrating the dot product of the vector field and the surface area element of the cylinder over the surface of the cylinder.

To calculate the flux passing through the cylinder, we first need to determine the surface area element of the cylinder in cylindrical coordinates. The surface area element in cylindrical coordinates is given by dS = r dr dθ dz, where r is the radial distance from the origin, θ is the azimuthal angle, and z is the vertical height.

Next, we need to determine the limits of integration for r, θ, and z. Since the cylinder has a radius of 2m and a height of 3m, we can set the limits of integration for r from 0 to 2, θ from 0 to 2π, and z from 0 to 3.

We can then calculate the flux passing through the cylinder using the formula for flux in cylindrical coordinates:

Φ = ∫∫ F ⋅ dS

where F is the vector field and dS is the surface area element. Substituting in the given vector field, we get:

Φ = ∫∫ (r^2 A + Zr zk) ⋅ (r dr dθ dz)

Expanding the dot product and integrating over the limits of integration, we get:

Φ = ∫0^3 ∫0^2π ∫0^2 (r^3 A + r^2 Zk) dr dθ dz

Evaluating the integrals, we get:

Φ = (4/3)π(2^4 A + 2^3 Z)

Therefore, the flux passing through the cylinder is (4/3)π(16A + 8Z).

Learn more about the flux here:- brainly.com/question/15655691

#SPJ11

When an object travels in a circle, it experiences a centripetal force which is directed towards the center of the circle. This force is given by:

F = m * v^2 / r

where F is the centripetal force, m is the mass of the object, v is its speed, and r is the radius of the circular path.

In this case, the mass of the vehicle is 1500 kg, the speed is 22 m/s, and the radius of the circle is 85 m. Plugging these values into the equation above, we get:

F = 1500 kg * (22 m/s)^2 / 85 m = 906.35 N

So, the centripetal force acting on the vehicle is 906.35 N.

The direction of the centripetal force is towards the center of the circle, which provides the necessary force to keep the vehicle moving in a circular path.

In conclusion, when a 1500-kg vehicle travels at a constant speed of 22 m/s around a circular track that has a radius of 85 m, it experiences a centripetal force of 906.35 N, which is directed towards the center of the circular path. This force is necessary to maintain the circular motion of the vehicle and prevents it from moving in a straight line.

To know more about velocity, visit:

https://brainly.com/question/80295

#SPJ11

To cause the particle to move to the right at 37 m/s, the direction of its velocity must be changed, which means that work must be done on the particle.

The net work required can be calculated using the work-energy theorem, which states that the net work done on an object is equal to the change in its kinetic energy.  Initially, the particle has a kinetic energy of (1/2)mv^2 = (1/2)(0.022 kg)(-13 m/s)^2 = 11.23 J.
To move the particle to the right at 37 m/s, its final kinetic energy will be (1/2)(0.022 kg)(37 m/s)^2 = 30.31 J.
Therefore, the net work required is equal to the change in kinetic energy:
net work = final kinetic energy - initial kinetic energy
net work = 30.31 J - 11.23 J
net work = 19.08 J
Thus, a net work of 19.08 J must be done on the particle to cause it to move to the right at 37 m/s.

The magnitude of the vertical velocity rises, but the horizontal velocity remains constant. The Y component determines how a projectile moves. The vertical component of velocity varies depending on whether a projectile is moving up or down, but it is always constant. The projectile is accelerated by gravity. Things fall to the earth faster as a result of gravity. The word "acceleration" describes a change in velocity, which is a calculation of the speed and direction of the motion. When anything falls for a longer period of time, gravity pushes it towards the earth more quickly, increasing its speed.

Learn more about velocity here

https://brainly.com/question/30559316

#SPJ11

The maximum velocity of a photoelectron emitted from a surface with a work function of 0.60 eV when illuminated by 413 nm ultraviolet light is 3.10 x 10^5 m/s.

The energy of a photon is given by the equation E = hc/λ, where h is Planck's constant, c is the speed of light, and λ is the wavelength of the light. For 413 nm ultraviolet light, the energy of a single photon is 3.01 eV.

If a photon has enough energy to exceed the work function of the surface, the excess energy is converted to the kinetic energy of the photoelectron . The maximum kinetic energy Kmax of the photoelectron is given by the equation Kmax = E - W, where W is the work function.

Kmax = 3.01 eV - 0.60 eV = 2.41 eV

Using the kinetic energy equation, K = 1/2 mv^2, where m is the mass of an electron, we can solve for the maximum velocity v of the photoelectron :

v = sqrt(2K/m) = sqrt(2(2.41 eV)(1.60 x 10^-19 J/eV)/(9.11 x 10^-31 kg)) = 3.10 x 10^5 m/s.

To learn more about, photoelectron , click here, https://brainly.com/question/16772624

#SPJ11

A charge of 5 nC is at the origin, and a cube with sides of length 1.2 m is centered on the origin. To find the magnitude of the electric flux through the top of the cube, we can use Gauss's law. Gauss's law states that the electric flux through a closed surface is proportional to the charge enclosed by the surface.

Since the cube is centered on the origin, the charge of 5 nC is enclosed by the cube. We can choose the top face of the cube as our closed surface. Since the electric field lines are perpendicular to the top face of the cube, the electric flux through the top face of the cube is simply the product of the electric field strength and the area of the top face of the cube.

To find the electric field strength at a distance of 0.6 m from the origin, we can use Coulomb's law, which states that the electric field strength at a distance r from a point charge q is given by E = kq/r^2, where k is Coulomb's constant.

Thus, the electric field strength at a distance of 0.6 m from the origin is E = (9x10^9 Nm^2/C^2)(5x10^-9 C)/(0.6 m)^2 = 1.04 N/C.

The area of the top face of the cube is (1.2 m)^2 = 1.44 m^2.

Therefore, the magnitude of the electric flux through the top of the cube is (1.04 N/C)(1.44 m^2) = 1.50 Nm^2/C.

Learn more about Coulomb's law here:- brainly.com/question/506926

#SPJ11

Relying on fate or astrology to choose an action implies a belief in predetermined outcomes and external guidance, which can have both comforting and limiting effects on decision-making and personal growth.

When someone relies on "fate" or astrology to choose an action, it implies that they believe in predestined outcomes and external influences guiding their decisions. This mindset often stems from a desire for guidance or assurance in uncertain situations. Astrology, for instance, is based on the idea that celestial bodies have a direct impact on human behavior and events, providing insights into one's personality, strengths, and potential future outcomes.

Relying on fate or astrology can have both positive and negative effects. On one hand, it may bring a sense of comfort and clarity in decision-making, promoting self-awareness and reflection. On the other hand, it could lead to passivity or inaction, as individuals might attribute their circumstances to external forces beyond their control. Additionally, this reliance could hinder personal growth and self-improvement, as one may not take responsibility for their actions or strive to change.

In conclusion, relying on fate or astrology to choose an action implies a belief in predetermined outcomes and external guidance, which can have both comforting and limiting effects on decision-making and personal growth.

Know more about  astrology here,

https://brainly.com/question/2438361

#SPJ11

The volume of the solid formed when c=0 and the region bounded by y=3x and y=0 is revolved around the x-axis is π cubic units.

When c=0, the region bounded by y=3x and y=0 lies entirely in the positive x-y quadrant. To find the volume of the solid formed, we need to use the method of cross-sections. Since the region is bound by a linear equation, we can use disks as cross-sections perpendicular to the x-axis.

The radius of the disk is given by the y-coordinate, which is 3x. The area of the disk is given by πr², which becomes π(3x)² = 9πx².

Integrating this expression from x=0 to x=1 (the bounds of the region), we get:
∫₀¹ 9πx² dx = π[3x³/3] from 0 to 1 = π(1-0) = π

Therefore, the volume of the solid formed when c=0 and the region bounded by y=3x and y=0 is revolved around the x-axis is π cubic units.

Learn more about finding the volume of solids here:

https://brainly.com/question/30548438

#SPJ11

Compared to a main-sequence star with a short lifetime, a main-sequence star with a long lifetime is less luminous, cooler, smaller, and less massive. This is because the length of a star's lifetime is largely determined by its mass.

More massive stars have a shorter lifespan because they burn through their fuel more quickly, while less massive stars have a longer lifespan because they burn their fuel more slowly. As a result, main-sequence stars with longer lifetimes tend to be smaller, cooler, and less luminous than those with shorter lifetimes.

This is because they are burning their fuel at a slower rate, producing less energy and heat. Additionally, less massive stars have lower surface temperatures, which also contributes to their lower luminosity and cooler temperature.

you know more about main-sequence star pls visit-

https://brainly.com/question/30369795

#SPJ11

A ball is thrown upward from the ground with an initial speed of 0.24 m/s.  The ball takes about 0.98 seconds to hit the ground.

To find the time it takes for the ball to hit the ground, we can use the kinematic equation:

y = vi*t + (1/2)at^2

where y is the displacement (change in height), vi is the initial velocity (0.24 m/s), a is the acceleration due to gravity (-9.81 m/s^2), and t is the time we want to find.

At the highest point of the ball's trajectory, its velocity is 0 m/s, so we can find the time it takes for the ball to reach that point:

vf = vi + a*t

0 = 0.24 m/s - 9.81 m/s^2 * t

t = 0.0245 seconds

To find the total time it takes for the ball to hit the ground, we can use the fact that the time up equals the time down:

t_total = 2 * t_up

t_total = 2 * 0.0245 seconds

t_total ≈ 0.98 seconds

To learn more about, velocity , click here, https://brainly.com/question/30559316

#SPJ11

The natural length of the spring is 9.75 cm. The work done on a spring is given by the formula W = (1/2) kx^2, where W is the work done, k is the spring constant, and x is the displacement of the spring from its natural length.

Let the natural length of the spring be x0. To find the spring constant, we can use the formula k = (W/x^2), where W is the work done and x is the displacement.

From the given problem, we can find the spring constant for the first stretch as:

k = (24 J) / (0.04 m)^2 = 150 N/m

For the second stretch, the total work done is 40 J, and we need to subtract the work done in the first stretch, which is 24 J. So the work done in the second stretch alone is 16 J. We can now find the spring constant for the second stretch as:

k = (16 J) / (0.04 m)^2 = 100 N/m

Now we can use the spring constant to find the natural length of the spring. Using the formula for the spring constant, we get:

k = (1/2) * ((F2/x2) - (F1/x1))

where F2 and x2 are the force and displacement for the second stretch, and F1 and x1 are the force and displacement for the first stretch.

Substituting the values, we get:

150 = (1/2) * ((F2/0.17) - (F1/0.13))

100 = (1/2) * ((F2/0.21) - (F1/0.17))

Solving these equations simultaneously, we get F1 = 4.8 N and F2 = 8 N.

Now using the formula for spring force, F = kx, we can find the natural length of the spring as:

F1 = kx0, or 4.8 = 150x0, giving x0 = 9.75 cm.

Learn more about displacement  here:- brainly.com/question/11934397

#SPJ11

Mechanical waves and electromagnetic waves are two types of waves that differ in their properties.

Some of the patterns that can be observed when comparing mechanical waves and electromagnetic waves:

Mechanical waves can only travel through a medium, while electromagnetic waves can travel through a vacuum.

Mechanical waves are created by the vibration of matter, while electromagnetic waves are created by the vibration of electric and magnetic fields.

The speed of a mechanical wave depends on the medium it is traveling through, while the speed of an electromagnetic wave is always the same (the speed of light in a vacuum).

The direction of propagation of a mechanical wave is perpendicular to the direction of vibration, while the direction of propagation of an electromagnetic wave is parallel to the direction of vibration.

Find out more on waves here: https://brainly.com/question/8511708

#SPJ1

When anti-lock braking system (ABS) engages during braking, you should keep pressure on your brake pedal. Therefore, option a is the correct answer.

ABS is designed to prevent the wheels from locking up and skidding during hard braking. It works by automatically modulating the brake pressure to each wheel to prevent it from locking up. When ABS engages, you may feel a pulsation or vibration in the brake pedal, and you may hear a noise.

It's important to keep firm and continuous pressure on the brake pedal when ABS engages. This allows the system to do its job and help you maintain control and stop the vehicle as quickly and safely as possible. Pumping the brake pedal or releasing pressure from the pedal can interfere with ABS operation and actually increase stopping distances.

Visit to know more about Anti-lock braking system:-

brainly.com/question/23879105

#SPJ11

If the temperature of a sample of water at 4°C is slightly increased, its volume will generally increase. However, water exhibits a unique behavior around 4°C that deviates from this general trend.

When water is cooled from higher temperatures, its volume decreases until it reaches approximately 4°C. At this point, water reaches its maximum density. However, as the temperature continues to decrease below 4°C, water expands and becomes less dense. This behavior is due to the arrangement of water molecules in a crystalline structure at lower temperatures.

Conversely, when the temperature of water at 4°C is increased, its volume generally increases as it follows the normal thermal expansion behavior. As water absorbs heat, the increased thermal energy causes the water molecules to move more vigorously, leading to an increase in the average distance between the molecules. This results in an expansion of the water's volume.

It's worth noting that this behavior is specific to water and does not apply to all substances. Most substances exhibit thermal expansion, where an increase in temperature leads to an increase in volume.

To know more about temperature please visit:

https://brainly.com/question/7510619

#SPJ11

The electric field vector in the plane of a dipole can be found using the equation E = (kq/d^3) * [(2x)/r^2, (y-z)/r^2, 0], where x is the distance from the dipole axis, y and z are the coordinates in the plane of the dipole, r is the distance from the dipole axis, d is the distance between the charges, and k is Coulomb's constant.

To explain further, a dipole is a pair of equal and opposite charges separated by a distance, and it generates an electric field. The electric field vector at any point in the plane of the dipole is the sum of the electric fields due to each charge. The equation mentioned above gives the electric field vector due to a single charge of magnitude q, and the total electric field vector is obtained by adding the electric field vectors due to each charge. The direction of the electric field vector is perpendicular to the plane of the dipole and points away from the positive charge and towards the negative charge.

Learn more about vector here:

https://brainly.com/question/29740341

#SPJ11

An open-tube manometer is a device used to measure the pressure difference between two points in a fluid, such as in a pipe or a tank. It consists of a U-shaped tube partially filled with a liquid, typically water or mercury, and open to the atmosphere on one or both ends. Here's a simple diagram and explanation of how an open-tube manometer works:

Open-tube manometer diagram

In this diagram, the open-tube manometer is connected to a pipe carrying a fluid whose pressure difference we want to measure. The left side of the manometer is open to the atmosphere, while the right side is connected to the pipe.

To measure the pressure difference, we first fill the manometer with a liquid, such as water or mercury, until the liquid level is the same on both sides of the U-tube. Let's assume the liquid is water and the fluid in the pipe is at a higher pressure than the atmosphere. As the fluid flows into the right side of the manometer, it pushes the water down, creating a difference in liquid levels in the two arms of the manometer. The height difference, h, between the two liquid levels is proportional to the pressure difference between the fluid in the pipe and the atmosphere.

Using the equation for pressure in a fluid, we can relate the pressure difference, ΔP, to the height difference, h, and the density of the liquid, ρ, as follows:

ΔP = ρgh

where g is the acceleration due to gravity. So, by measuring the height difference, h, and knowing the density of the liquid, we can calculate the pressure difference, ΔP.

Note that the direction of the pressure difference depends on the direction of the flow. If the fluid in the pipe is at a lower pressure than the atmosphere, the water level in the left arm of the manometer will be higher than that in the right arm, and the height difference, h, will be negative.

Overall, an open-tube manometer is a simple and effective device for measuring pressure differences in fluids.

For more question on open-tube manometer click on

https://brainly.com/question/12924478

#SPJ11

To calculate the magnitude of the Earth's acceleration just before the impact of a falling meteorite, we can use Newton's law of universal gravitation: F = G * (m1 * m2) / r^2 where F is the gravitational force between two objects, G is the gravitational constant, m1 and m2 are the masses of the objects, and r is the distance between their centers.

In this case, the Earth's mass (m1) is given as 5.98 × 10^24 kg, and the meteorite's mass (m2) is given as 4000 kg. We need to find the acceleration, which is the force acting on the meteorite divided by its mass. Rearranging the formula, we have:
F = m2 * a
Solving for F, we get:
F = G * (m1 * m2) / r^2
Now we can substitute the given values into the formula:
G = 6.67430 × 10^-11 m^3/kg/s^2 (gravitational constant)
m1 = 5.98 × 10^24 kg (mass of the Earth)
m2 = 4000 kg (mass of the meteorite)
r = radius of the Earth (assumed to be constant)
To find the radius of the Earth, we can use the formula for the acceleration due to gravity on the surface of the Earth:
g = G * m1 / r^2
Solving for r, we have:
r = sqrt(G * m1 / g)
Substituting the values into the formula, we can calculate the radius of the Earth. Finally, using the calculated radius, we can substitute the values of G, m1, and m2 into the formula for the gravitational force F, and then divide by the mass of the meteorite (m2) to find the acceleration (a). Therefore, the magnitude of the Earth's acceleration just before impact can be determined by calculating the gravitational force and dividing it by the mass of the meteorite.

To know more about gravitational force, click here
https://brainly.com/question/12528243

#SPJ11

The tension required for the rope to have transverse waves with a frequency of 37.0 Hz and a wavelength of 0.760 m is approximately 38.8 N.

To find the tension required for the rope, we can use the formula:

Tension = (mass per unit length) x (wave speed)²

First, let's calculate the wave speed:

wave speed = frequency x wavelength

wave speed = 37.0 Hz x 0.760 m

wave speed = 28.12 m/s

Next, let's find the mass per unit length of the rope:

mass per unit length = mass / length

mass per unit length = 0.115 kg / 2.40 m

mass per unit length = 0.048 kg/m

Now we can substitute these values into the tension formula:

Tension = (0.048 kg/m) x (28.12 m/s)²

Tension = 38.8 N

Therefore, the tension required for the rope to have transverse waves with a frequency of 37.0 Hz and a wavelength of 0.760 m is approximately 38.8 N.

To know more about wave speed, visit:

https://brainly.com/question/31682106

#SPJ11