Answer:
Keep on moving
Explanation:
Newton's first law states "that, if a body is at rest or moving at a constant speed in a straight line, it will remain at rest or keep moving in a straight line at constant speed unless it is acted upon by a force."
Static Friction
Now let’s examine the static case. Remain on the “Force graphs” tab at the top of the window. Make sure the box labeled “Ffriction” is checked at the left of the screen, this will allow us to measure to force of friction experienced by an object as it slides down the ramp.
Draw a free body diagram for an object sitting on the incline at rest, assuming the incline is at the maximum angle BEFORE the object starts to move. Be sure to include friction and stipulate whether it is kinetic or static.
A 450.0 kg roller coaster is traveling in a circle with radius 15.0m. Its speed at point A is 28.0m/s and its speed at point B is 14.0 m/s. At point A the cart is already moving with circular motion. a) Draw free bodydiagramsfor the cartatpointsAand B(two separate free body diagrams). b) Calculate the acceleration of the cartat pointsAandB(magnitude and direction). c) Calculate the magnitude of the normal force exerted by the trackson the cartat point A. d) Calculate the magnitude of the normal force exerted by the tracks on the cart at point B.
Answer:
b) a = 52.26 m / s², a ’= 13.06 m / s², c) N = 2.79 10⁴ N, d) N = 1.89 10³ N
Explanation:
a) In the attached we can see the free body diagrams for the two positions, position A in the lower part of the circle and position B in the upper part of the circle
b) Let's start at point A
Let's use that the acceleration is centripetal
a = v² / r
let's calculate
a = 28² / 15.0
a = 52.26 m / s²
as they relate it is centripetal it is directed towards the center of the circle, therefore for this point it is directed vertically upwards
Point B
a ’= 142/15
a ’= 13.06 m / s²
in this case the acceleration is vertical downwards
c) The values of the normal force
point A
let's use Newton's second law
∑ F = m a
N- W = m a
N = mg + ma
N = m (g + a)
N = 450.0 (9.8 + 52.25)
N = 2.79 10⁴ N
d) Point B
-N -W = m (-a)
N = ma -m g
N = m (a-g)
N = 450.0 (14.0 - 9.8)
N = 1.89 10³ N
What is the acceleration of a car that goes from 0 MS to 60 MS and six seconds
39. What is the change in momentum for a 5,000 kg ship in
outer space that experiences no net force over a 1 hr
period?
Answer:
Change in momentum is zero.
Explanation:
The following data were obtained from the question:
Mass (m) = 5000 kg
Time (t) = 1 h
Net force (F) = 0
Change in momentum =?
Force = Rate of change of momentum
0 = change in momentum
Change in momentum = 0
We can see from the above illustration that the net force is zero. Thus, the change in momentum is also zero.
The masses of astronauts are monitored during long stays in orbit, such as when visiting a space station. The astronaut is strapped into a chair that is attached to the space station by springs and the period of oscillation of the chair in a friction-less track is measured.
(a) The period of oscillation of the 10.0 kg chair when empty is 0.750 s. What is the effective force constant of the springs?
(b) What is the mass of an astronaut who has an oscillation period of 2.00 s when in the chair?
(c) The movement of the space station should be negligible. Find the maximum displacement of the 100,000 kg sace station if the astronaut's motion has an amplitude of 0.100 m.
Answer:
a) k = 701.8 N / m, b) m_{ast} = 61.1 kg, c) v ’= -1.3 10⁻⁴ m / s
Explanation:
a) For this exercise let's use the relationship of the angular velocity
w = [tex]\sqrt{ \frac{k}{m} }[/tex]
k = w² m
the angular velocity is related to the period
w = 2π / T
we substitute
k = 4 π² [tex]\frac{m}{T^2}[/tex]
let's calculate
k = 4 π² 10 /0.75²
k = 701.8 N / m
b) now repeat the measurement with an astronaut on the chair
w = [tex]\sqrt{ \frac{k}{m} }[/tex]
where the mass Month the mass of the chair plus the mass of the astronaut
M = m + [tex]m_{ast}[/tex]
M = k / w²
w = 2π / T
let's calculate
w = 2π / 2
w = π rad / s
M = 701.8 /π²
M = 71,111 kg
now we use that
M = m + m_{ast}
m_{ast} = M - m
m_{ast} = 71.111 - 10.0
m_{ast} = 61.1 kg
c) if the astronaut's movement is simple harmonic
x = A cos wt
therefore the speed is
v = [tex]\frac{dx}{dt}[/tex]
v = -Aw sin wt
maximum speed is
v = - Aw
v = 0.100 π
v = 0.31416 m / s
we can suppose that the movement of the space station and the astronaut is equivalent to division of the same
initial instant. Before the move
p₀ = 0
final instant. When the astronaut is moving
p_f = M_station v’+ m_{ast} v
the moment is preserved
p₀ = pf
0 = M__{station} v ’+ m_{ast} v
v ’= - [tex]\frac{m_{ast} }{M_{station} } \ v[/tex]
we substitute
v ’= [tex]\frac{61.1 }{ 100000 } \ 0.31416[/tex]
v ’= -1.3 10⁻⁴ m / s
the negative sign indicates that the station is moving in the opposite direction from the astronaut
Shanti is riding on a train that is moving at a speed of 90 km/h. He is carrying a power cord for his phone that is 1.2 m long.
Which describes the length of the power cord when Shanti gets off the train?
cannot be determined
less than 1.2 m
more than 1.2 m
equal to 1.2 m
Answer:
D. equal to 1.2
Explanation:
on edg
The length of the power cord will be equal to 1.2 m.
Describe about the length of power cord? The train is moving at a speed of 90 km /hr. Train was moving but the person in the train can be considered to be at rest. Shanti is the person travelling on the train. Her cord can be used only by her and the cord length of the phone will be 1.2 m.The length can be measured through the distance.The unit of length is meter.As we know the concept of motion and rest, there only the train in motion, shanti was at rest and shanti's power cord were also in the rest. Power cord length will be determined only at the time of manufacturing.If the power cord length to be change then the crimping process.So, the length will not change suddenly.
The length of the power cord when shanti gets off the train is equal to 1.2 m.
The Correct answer is Option D.
Learn more about motion and rest,
https://brainly.com/question/12284808
#SPJ5
your "A" never changes, while your "Y" changes depending on strength of gravity. is it mass or weight?
Answer:
A - mass. B - Weight
Explanation:
This is because weight varies with the strength of gravity. Mass is just the amount of matter in an object
QUCIK!! SOMEONE PLEASE HELP! I’LL MARK BRAINLIEST!!
Answer:
A. v = √2gh
B. No! The final velocity does not depend on the mass of the car.
C. Yes! the final velocity depends on the steepness of the hill
D. 3.28 m/s
Explanation:
A. Determination of the final velocity.
½mv² = mgh
Cancel out m
½v² = gh
Cross multiply
v² = 2gh
Take the square root of both side
v = √2gh
B. Considering the formula obtained for the final velocity i.e
v = √2gh
We can see that there is no mass (m) in the formula.
Thus, the final velocity does not depend on the mass of the car.
C. Considering the formula obtained for the final velocity i.e
v = √2gh
We can see that there is height (h) in the formula.
Thus, the final velocity depends on the steepness of the hill
D. Determination of the final velocity.
Height (h) = 0.55 m
Acceleration due to gravity (g) = 9.8 m/s²
Velocity (v) =?
v = √2gh
v = √(2 × 9.8 × 0.55)
v = √10.78
v = 3.28 m/s
Please help 25 points!
Three waves with frequencies of 1 Hertz (Hz), 3 Hz, and 9Hz travel at the same speed. Which of the following statements is correct?
A. The 1 Hz wave contains the most energy.
B. The crests of all three waves are of equal height.
C. The wavelength of the 9Hz wave is three times that of the 3 Hz wave.
D. The 1 Hz wave has the longest wavelength.
Answer:
B
Explanation:
The crest of all three waves are of equal height
A particle move in the xy plane so that its position vector r=bcosQi +bsinQj+ ctk, where b, Q and c are constants. show that the partial move with constant speed.
Answer:
The speed of this particle is constantly [tex]c[/tex].
Explanation:
Position vector of this particle at time [tex]t[/tex]:
[tex]\displaystyle \mathbf{r}(t) = b\, \cos(Q)\, \mathbf{i} + b\, \sin(Q) \, \mathbf{j} + c\, t\, \mathbf{k}[/tex].
Write [tex]\mathbf{r}(t)[/tex] as a column vector to distinguish between the components:
[tex]\mathbf{r}(t) = \begin{bmatrix}b\, \cos(Q) \\ b\, \sin(Q) \\ c\, t\end{bmatrix}[/tex].
Both [tex]b[/tex] and [tex]Q[/tex] are constants. Therefore, [tex]b\, \cos(Q)[/tex] and [tex]b \sin (Q)[/tex] would also be constants with respect to [tex]t[/tex]. Hence, [tex]\displaystyle \frac{d}{dt}[b\, \cos(Q)] = 0[/tex] and [tex]\displaystyle \frac{d}{dt}[b\, \sin(Q)] = 0[/tex].
Differentiate [tex]\mathbf{r}(t)[/tex] (component-wise) with respect to time [tex]t[/tex] to find the velocity vector of this particle at time [tex]t\![/tex]:
[tex]\begin{aligned}\mathbf{v}(t) &= \frac{\rm d}{{\rm d} t} [\mathbf{r}(t)] \\ &=\frac{\rm d}{{\rm d} t} \left(\begin{bmatrix}b\, \cos(Q) \\ b\, \sin(Q) \\ c\, t\end{bmatrix}\right) \\ &= \begin{bmatrix}\displaystyle \frac{d}{dt}[b\, \cos(Q)] \\[0.5em] \displaystyle \frac{d}{dt}[b\, \sin(Q)]\\[0.5em]\displaystyle \frac{d}{dt}[c \cdot t]\end{bmatrix} = \begin{bmatrix}0 \\ 0 \\ c\end{bmatrix}\end{aligned}[/tex].
The speed [tex]v[/tex] (a scalar) of a particle is the magnitude of its velocity :
[tex]\begin{aligned}v(t) &= \| \mathbf{v}(t) \| \\ &= \left\|\begin{bmatrix}0 \\ 0 \\ c\end{bmatrix}\right\| \\ &= \sqrt{0^2 + 0^2 + c^2} = c\end{aligned}[/tex].
Therefore, the speed of this particle is constantly [tex]c[/tex] (a constant.)
.................,,,,,,,,,,,
Answer:
B
Explanation:
Motion is movement, the teacher's movement is motion
A storage tank has the shape of an inverted circular cone with height 12 m and base radius of 4 m. It is filled with water to a height of 10 m. Find the work required to empty the tank by pumping all of the water to the top of the tank. (The density of water is 1000 kg/m3. Assume g
Answer:
Work required to empty the tank by pumping all of the water to the top of the tank = 1674700 Kgm/s^2
Explanation:
Volume of Circular cone = V = (1/3)πr2h
where r is the radius in meters
and h is the height in meters
Substituting the given values in above equation, we get -
V = [tex]\frac{1}{3} * 3.14 * 4^2 * 10 = 167.47[/tex] cubic meters.
The force required will be equal to the mass of water in the cone
[tex]= 167.47 * 1000[/tex]
= 167470 Kg
Weight = Mass * g
= 167470 * 10
= 1674700 Kgm/s^2
Flying insects such as bees may accumulate a small positive electric charge as they fly. In one experiment, the mean electric charge of 50 bees was measured to be +(30±5)pC+(30±5)pC per bee. Researchers also observed the electrical properties of a plant consisting of a flower atop a long stem. The charge on the stem was measured as a positively charged bee approached, landed, and flew away. Plants are normally electrically neutral, so the measured net electric charge on the stem was zero when the bee was very far away. As the bee approached the flower, a small net positive charge was detected in the stem, even before the bee landed. Once the bee landed, the whole plant became positively charged, and this positive charge remained on the plant after the bee flew away. By creating artificial flowers with various charge values, experimenters found that bees can distinguish between charged and uncharged flowers and may use the positive electric charge left by a previous bee as a cue indicating whether a plant has already been visited (in which case, little pollen may remain). What is the best explanation for the observation that the electric charge on the stem became positive as the charged bee approached (before it landed)?
(a) Because air is a good conductor, the positive charge on the bee’s surface flowed through the air from bee to plant.
(b) Because the earth is a reservoir of large amounts of charge, positive ions were drawn up the stem from the ground toward the charged bee.
(c) The plant became electrically polarized as the charged bee approached.
(d) Bees that had visited the plant earlier deposited a positive charge on the stem.
Answer:
a) True
Explanation:
There are several possible explanations for this positive charge
* The explanation of the small positive charge in the plant when the bee approaches is like a defense system of the plants,
to prevent the bees from taking the pollen, but the flowers need the bees to transport the pollen for fertilization, so this possibility is not correct
* The air is conductive so the bee indexes a charge in the nearby air, this charge must be negative and this charge induced in the air induces a charge on the flower that must be positive.
When reviewing the different statements we have
a) True, it agrees with the second explanation of the phenomenon
b) False. The earth is a deposit of negative charge
c) false. If this is the case the charge should be negative
d) False. This residual charge from the other bees is quickly neutralized by the charge from the Earth.
Answer:
Explanation:
.
Common transparent tape becomes charged when pulled from a dispenser. If one piece is placed above another, the repulsive force can be great enough to support the top piece's weight. Assuming equal point charges (only an approximation), calculate the magnitude of the charge if electrostatic force is great enough to support the weight of a 12.0 mg piece of tape held 0.55 cm above another. (The magnitude of this charge is consistent with what is typical of static electricity.)
Answer:
q = 2 10⁻⁸ C
Explanation:
For this exercise we use the translational equilibrium equation
F_e -A =
F_e = W
the electric force is given by Coulomb's law
F_e = [tex]k \frac{q_1q_2}{r^2}[/tex]
in this case they indicate that the loads on the tapes are equal
F_e = k q² / r²
we substitute
k q² / r² = m g
q = [tex]\sqrt{ \frac{mg r^2}{k} }[/tex]
calculate
q = [tex]\sqrt { \frac{ 12 \ 10^{-3} \ 9.8 (0.55 \ 10^{-2})^2 }{9 \ 10^9} }[/tex]
q = [tex]\sqrt{ 3.9526 \ 10^{-16}[/tex]
q = 1,999 10⁻⁸ C
q = 2 10⁻⁸ C
An object is dropped from a bridge. A second object is thrown downwards 1.0 s later. They both reach the water 20 m below at the same instant. What was the initial speed of the second object? Neglect air resistance.
A spring with a constant of 76 N/m is extended by 0.9 m. How much energy is stored in the extended spring?
Answer:
[tex]E=30.78\ J[/tex]
Explanation:
The force constant of the spring, k = 76 N/m
The extension in the spring, x = 0.9 m
We need to find the energy is stored in the extended spring. The energy stored in the spring is given by :
[tex]E=\dfrac{1}{2}kx^2\\\\E=\dfrac{1}{2}\times 76\times (0.9)^2\\\\E=30.78\ J[/tex]
So, 30.78 J of energy is stored in the spring.
Which statement best compares potential and kinetic energy?
O Objects always have more potentiał energy than kinetic energy.
O Kinetic energy increases and potential energy decreases when the velocity of an object increases
O Only potential energy decreases when an object's height increases.
O Objects always have more kinetic energy than potential energy.
Answer:
Kinetic energy increases and potential energy decrease when velocity of an object increase.
A student is conducting an experiment to compare the resistivity of two unknown materials by using two wires, each made of one of the materials and each connected in a circuit. The student measures the potential difference across and current in the wires. What must be the same to be able to compare the resistivities using just the potential difference and current measurements?
Answer:
is there a. b. c or d?
Explanation:
If you have a 0.125 kg lead piece at
20.0°C, how much heat must you
add to melt it? (Remember, you
must warm it to its melting point
first.)
Material
Lead
Melt Pt (°C)
327
L (1/kg)
2.32.104
Boil Pt (°C) Lv (1/kg)
1750 8.59.105
c (1/(kg*c)
128
(Unit = J)
Answer:
7,812 J
Explanation:
Using the relation:
Q = mcΔθ
Q = quantity of heat
C = specific heat capacity of lead
Δθ = temperature change (T2 - T1)
M = mass of substance
Q = mass * specific heat * Δθ
Q = 0.125kg * 128 * (327 – 20)
Q = 0.125 * 128 * 307
Q = 4912 J
For melting:
Q = mass * Hf
0.125 * (2.32 * 10^4)
= 2,900 J
Total = 4,912 J + 2,900 J = 7,812 J
Which is an example of kinetic energy?
A. The energy stored in
ethanol
B. A ball sitting at the top of a ramp
C. A compressed spring
D. A hockey puck sliding across ice
D. A hockey puck sliding across ice
You and a friend each hold a lump of wet clay. Each lump has a mass of 30 grams. You each toss your lump of clay into the air, where the lumps collide and stick together. Just before the impact, the velocity of one lump was < 3, 3, -3 > m/s, and the velocity of the other lump was < -4, 0, -4 > m/s. What is the velocity of the stuck-together lump just after the collision
Answer:
[tex]<-0.5, 1.5, -3.5>\ \text{m/s}[/tex]
Explanation:
[tex]u_1[/tex] = Velocity of one lump = [tex]3x+3y-3z[/tex]
[tex]u_2[/tex] = Velocity of the other lump = [tex]-4x+0y-4z[/tex]
m = Mass of each lump = [tex]30\ \text{g}[/tex]
The collision is perfectly inelastic as the lumps stick to each other so we have the relation
[tex]mu_1+mu_2=(m+m)v\\\Rightarrow m(u_1+u_2)=2mv\\\Rightarrow v=\dfrac{u_1+u_2}{2}\\\Rightarrow v=\dfrac{3x+3y-3z-4x+0y-4z}{2}\\\Rightarrow v=-0.5x+1.5y-3.5z=<-0.5, 1.5, -3.5>\ \text{m/s}[/tex]
The velocity of the stuck-together lump just after the collision is [tex]<-0.5, 1.5, -3.5>\ \text{m/s}[/tex].
The current flow in the light bulb is 0.5A
a.Calculate the amount of electric charge that flow through the bulb in 2 hour
b.If one election carries a
charge 1.6 x 10-14 c Find the number of election through the bulb in 2 hour?
Answer:
Explanation:
Given that,
The current in the light bulb, I = 0.5 A
(a) We know that,
Electric current = charge/time
or
Q = It
Put t = 2 hours = 7200 s
So,
Q = 0.5 × 7200
Q = 3600 C
(b) Charge on one electron, [tex]Q=1.6\times 10^{-19}\ C[/tex]
Let there are n electrons flow through the bulb in 2 hours.
I = Q/t
Since, Q = ne
So,
I = ne/t
[tex]n=\dfrac{I\times t}{e}\\\\n=\dfrac{0.5\times 7200}{1.6\times 10^{-19}}\\\\n=2.25\times 10^{22}[/tex]
Hence, this is the required solution.
- .
?
y
(っ◔◡◔)っ ♥ chose the answer with the question marks ♥
Answer:
okay I'm a bit confused but I like the little emoji dudw
Answer:
?
Explanation:
.
Help plsssssssssss I write it 100 time no one answer
Answer:
1.93×10²⁸ s
Explanation:
From the question given above, the following data were obtained:
Number of electron (e) = 2×10²⁴
Current (I) = 10 A
Time (t) =?
Next, we shall determine the quantity of electricity flowing through pasing through the point. This can be obtained as follow:
1 e = 96500 C
Therefore,
2×10²⁴ e = 2×10²⁴ e × 96500 / 1 e
2×10²⁴ e = 1.93×10²⁹ C
Thus, 1.93×10²⁹ C of electricity is passing through the point.
Finally, we shall determine the time. This can be obtained as follow:
Current (I) = 10 A
Quantity of electricity = 1.93×10²⁹ C
Time (t) =?
Q = it
1.93×10²⁹ = 10 × t
Divide both side by 10
t = 1.93×10²⁹ / 10
t = 1.93×10²⁸ s
Thus, it took 1.93×10²⁸ s for 2×10²⁴ electrons to pass through the point
how many pennies can 4 folds of a paper hold?
A soccer ball was kicked over the edge of a wall and traveled 35 m horizontally at a speed of 5.6m/s. Calculate the vertical height of the wall.
Answer:
Are you sure it was soccer ball? Or meine hearts
Explanation:
A 50kg mass is sitting on a frictionless surface. An unknown constant force pushes the mass for 2 seconds until the mass reaches a velocity of 3m/s. What was the force acting on the mass?
Answer:
75N
Explanation:
a = v/t = 3/2
F = ma = 50(3/2) = 75
If the diameter of a moose eye is 40 mm, what is the total refractive power of the anterior portion of the eye?
Answer:
-the ratio of the speed of light
in air to the speed of light in the substance.
-speed of light in air 300,000 km/sec, which decreases when it passes through a transparent substance.
-e.g.. speed of light in substance = 200,000 km/sec, R.I. = 300,000/200,000 = 1.5
Explanation:
Given that Carbon-14 has a half-life of 5700 years, determine how long it would take for
this reduction to occur.
Answer:It will take about 3000 years
Explanation:
Two identical conducting spheres are placed with their centers 0.30 m apart. One is given a charge of 12 X10^-9 C and the other is given a charge of -18 X 10^-9 C. a. Find the electric force exerted on one sphere by the other. b. The sphere are connected by a conducting wire. After equilibrium has occurred, find the electric force between the two spheres.
Answer:
Explanation:
Force between two charged conducting sphere
= k x Q₁ x Q₂ / r² , k is a constant Q₁ and Q₂ are charges and r is distance between them .
= 9 x 10⁹ x 12 x 10⁻⁹ x 18 x 10⁻⁹ / .30²
= 21600 x 10⁻⁹
= 2.16 x 10⁻⁵ N .
b )
After the spheres are joined together , there is redistribution of charge and remaining charge will be equally shared by them .
Charge on each sphere = (12 - 18 ) x 10⁻⁹ / 2
= - 3 x 10⁻⁹ C .
Force = 9 x 10⁹ x 3 x 10⁻⁹ x 3 x 10⁻⁹ / .30²
= 900 x 10⁻⁹ N .