1. Collect data on the rate constants (k) of the reaction at various temperatures, (2) Take the natural logarithm of the Arrhenius equation to obtain a linear equation: ln(k) = ln(A) - Ea/RT.
3. Plot ln(k) vs 1/T and determine the slope of the line. 4. Use the slope and the gas constant (R) to calculate the activation energy (Ea) using the equation: Ea = -slope x R. 1. Rearrange the Arrhenius equation to isolate Ea: ln(k) = ln(A) - (Ea / RT), (2). Determine the rate constants (k) at two different temperatures (T1 and T2) from experimental data.
3. Substitute the known values of k, R (gas constant), and T into the equation for each temperature: ln(k1) = ln(A) - (Ea / R * T1), ln(k2) = ln(A) - (Ea / R * T2), 4. Subtract the first equation from the second to eliminate A: ln(k2 / k1) = Ea / R * (1/T1 - 1/T2) 5. Rearrange the equation to solve for Ea: Ea = R * ln(k2 / k1) / (1/T1 - 1/T2) 6. Calculate the activation energy (Ea) by plugging in the known values of k1, k2, T1, T2, and R into the final equation.
To know more about temperatures click here
brainly.com/question/30074492
#SPJ11
How slowly do plates move? Use the Sim to measure how far plates move from each other over time and use your measurements to calculate the rate of plate motion.
On one device, open the Plate Motion Sim. On the other device, leave this screen open.
Go to Region 2 of the Sim.
Add a GPS marker to each plate as close as possible to each other and to the plate boundary.
Press SET BOUNDARY and select Divergent as the plate boundary type. Then press RUN.
During the run, press Pause approximately every 50 million years. Record the time in the first column of the table below. Observe the distance between the two pins by pressing on either pin and reading the distance to the other and then record that number in the Distance column. You can press the Reset button in the top right corner to replay the Sim.
Calculate the rate for each pair of distances and times by dividing the distance by the time. Record those numbers in the Rate column.
The Plate Motion Sim provides a helpful visualization of how plates move and how we can measure their motion and scientists can better predict and prepare for geological events like earthquakes and volcanic eruptions.
Based on the Plate Motion Sim, the rate of plate motion varies over time and ranges from about 1 to 10 cm per year. The Sim shows that plates move slowly but steadily, and their movement can be observed over millions of years.
For example, after 50 million years, the distance between the two GPS markers in Region 2 increased by approximately 500 km, resulting in a rate of 10 cm per year. After 100 million years, the distance increased by approximately 1000 km, resulting in a rate of 10 cm per year. After 150 million years, the distance increased by approximately 1500 km, resulting in a rate of 10 cm per year.
To learn more about Motion follow the link:
https://brainly.com/question/14701044
#SPJ1
complete the description of crystalline lattices and lattice energy as they relate to ionic compounds. some terms will be used more that once, whereas some terms will not be used at all. Ionic ____________ in their solid state form _________ lattices of alternating metallic__________ and nonmetallic __________. The __________ of this lattice releases a large amount of energy, known as the ________ energy. Note that ___________ energy cannot be directly measured, but can only be approximated using ____________-___________ ____________ and its corresponding calculations.
Ionic compounds in their solid state form crystalline lattices of alternating metallic cations and nonmetallic anions. The formation of this lattice releases a large amount of energy, known as the lattice energy.
This energy is the energy that is released when two oppositely charged ions come together and form a crystal lattice. It is this energy that is responsible for the stability of the solid ionic compound.
Lattice energy cannot be directly measured, but can only be approximated using thermodynamic data and its corresponding calculations.
Thermodynamic data such as enthalpy of formation, and entropy of formation are used to calculate the lattice energy of a given ionic compound. This lattice energy is the energy that must be put into an ionic compound to break it down into its component ions and gaseous form.
Know more about thermodynamic data here
https://brainly.com/question/29980991#
#SPJ11
Can you guys help me with this
There would be few or no clouds near a high pressure system. Option C
What is the cloud cover?When a high pressure system is nearby, the weather is usually bright and dry, which might lead to a low cloud cover. In general, high pressure systems are related to falling air, which prevents clouds from forming and growing.
This is due to the fact that cooling and drying effects of descending air reduce relative humidity and constrict the quantity of moisture that can be used to build clouds.
Learn more about cloud cover:https://brainly.com/question/10050351
#SPJ1
In terms of bonding, explain why ethanol and water are miscible, yet carbon tetrachloride and water are immiscible?
The ethanol dissolves in water but carbon tetrachloride will not dissolve it is because of the hydrogen bonding present in ethanol but carbon tetrachloride does not contain hydrogen bonding
The similarity of the intermolecular interactions between the molecules of the two liquids—which is defined by the kinds and strengths of the bonds present in each molecule—is what determines whether two liquids are miscible. Compared to carbon tetrachloride and water, which have different polarities and weak intermolecular interactions, ethanol and water are miscible because of shared polarity and capacity to form hydrogen bonds.
The types of intermolecular forces that exist between the molecules of the two liquids determine whether two liquids are miscible. Due to the existence of polar -OH groups, ethanol and water have similar intermolecular interactions because both molecules are polar in nature. Therefore, ethanol molecules can form.
To know more about Hydrogen Bonding refers to this link
https://brainly.com/question/1420470
Consider the decomposition of liquid benzene, C6H61l2, to gaseous acetylene, C2H21g2: C6H61l2 ¡ 3 C2H21g2 H = +630 kJ (a) What is the enthalpy change for the reverse reaction?
The enthalpy change for the reverse reaction is +630 kJ. This indicates that the reverse reaction is endothermic, which means that it requires energy to occur.
The enthalpy change for the reverse reaction can be obtained by simply reversing the direction of the given reaction and changing the sign of the enthalpy change. So, the balanced equation for the reverse reaction is:
3 [tex]C_{2}H_{2}[/tex](g) → [tex]C_{6}H_{6}[/tex](l) ΔH = -630 kJ
The enthalpy change for the reverse reaction is therefore:
ΔH = -(-630 kJ) = +630 kJ
Enthalpy is a thermodynamic property that describes the amount of energy in a system, which can be exchanged with its surroundings as heat or work. It is represented by the symbol H and is often described as the "heat content" of a substance or a reaction. Enthalpy is commonly used in chemistry to describe the heat absorbed or released during chemical reactions.
The enthalpy change of a reaction is the difference between the enthalpies of the products and the reactants, and it is usually measured in units of joules per mole (J/mol). Enthalpy is also used to describe the behavior of gases and other substances at different temperatures and pressures. The enthalpy of a substance is related to its internal energy, which is the sum of the kinetic and potential energies of its molecules. Changes in enthalpy can be used to predict the behavior of chemical reactions and other thermodynamic processes.
To learn more about Enthalpy visit here:
brainly.com/question/16720480
#SPJ4
1. the unknown metals x and y were either magnesium, silver, or zinc. use the text value for the reduction potential of pb and your measured cell potentials for the unknowns to identify x and y
By comparing the measured cell potentials with the reduction potential of Pb, we can determine the identity of metals X and Y.
To identify the unknown metals X and Y, we can compare their measured cell potentials with the reduction potentials of different metals, including magnesium (Mg), silver (Ag), and zinc (Zn). By using the reduction potential of lead (Pb) as a reference, we can determine which metals have higher or lower reduction potentials.
First, let's assume X is one of the metals and Y is the other. We can compare the measured cell potentials for X and Y with the reduction potential of Pb.
If the measured cell potential for X is more negative than the reduction potential of Pb, and the measured cell potential for Y is more positive than the reduction potential of Pb, then X is more easily oxidized than Pb (has a lower reduction potential) and Y is less easily oxidized than Pb (has a higher reduction potential).
By comparing the measured cell potentials with the reduction potential of Pb, we can determine the identity of metals X and Y.
Learn more about cell potentials: brainly.com/question/1313684
#SPJ11
The vapor pressure of water at 25C is 3. 13X10^-2 atm, and the heat vaporization of water at 25 C is 4. 39 X 10^4 j/mol. Calculate the vapor pressure of water at 81C
The vapor pressure of water at 81°C is 3.61 atm.
To calculate the vapor pressure of water at 81°C, we can use the Clausius-Clapeyron equation, which relates the vapor pressure of a substance to its enthalpy of vaporization and temperature.
The equation is:
ln(P2/P1) = (ΔHvap/R) x (1/T1 - 1/T2)
where:P1 = vapor pressure at temperature T1
P2 = vapor pressure at temperature T2
ΔHvap = heat of vaporization
R = gas constant (8.314 J/mol K)
We can use the equation to solve for P2, given that we know P1, ΔHvap, T1, and T2. We will assume that the heat of vaporization of water is constant over this temperature range.
First, we need to convert the temperatures to Kelvin:
T1 = 25°C + 273.15 = 298.15 K
T2 = 81°C + 273.15 = 354.15 K
Next, we can plug in the values we know:
ln(P2/3.13x10-²) = (4.39x10⁴ J/mol / 8.314 J/mol K) x (1/298.15 K - 1/354.15 K)
Simplifying the right-hand side of the equation:
ln(P2/3.13x10-² atm) = 19.7
Finally, solving for P2:
P2/3.13x10-² atm = e¹⁹·⁷
P2 = 3.61 atm
To learn more about vapor pressure here:
https://brainly.com/question/30396289
#SPJ4
Physical, Chemical, or Therapeutic Incompatibility?:
Synergism between propofol and alcohol.
In this case, propofol and alcohol both have depressant effects on the central nervous system, which means that when taken together, their combined effects are more potent than if they were taken separately.
The synergism between propofol and alcohol can be classified as a type of chemical incompatibility. This is because when these two substances are combined, they can have a greater effect than if they were taken separately, potentially leading to dangerous interactions and adverse effects.
However, it is important to note that this chemical incompatibility can also lead to physical and therapeutic incompatibility, as the combined effects of propofol and alcohol can cause physical symptoms and may not be suitable for certain therapeutic applications.
In this case, propofol and alcohol both have depressant effects on the central nervous system, which means that when taken together, their combined effects are more potent than if they were taken separately. This can lead to increased sedation, respiratory depression, and other potential risks.
to learn more about respiratory depression click here:
brainly.com/question/31597354
#SPJ11
In an impressed current system,
A) the rectifier negative terminal is connected to the anodes
B) the rectifier positive terminal is connected to the anodes
C) the rectifier positive terminal is connected to the structure
D) conventional current in the soil goes from the structure to the anodes
In an impressed current system, the rectifier positive terminal is connected to the anodes. Therefore the correct option is option B.
A regulated electrical current is applied to a metallic structure as part of the impressed current cathodic protection (ICCP) technique to prevent corrosion.
The anodes in an ICCP system are often formed of a material that degrades over time, like graphite or titanium, and they are buried in the soil or electrolyte surrounding the building to provide protection.
The cathodic protection current travels to the structure after the anodes receive a direct electrical current from the rectifier and release their stored electrons into the soil or electrolyte.
The potential of the structure can be changed to a more negative value by managing the current flow, which lessens the likelihood of corrosion happening. Therefore the correct option is option B.
For such more question on anodes:
https://brainly.com/question/31520156
#SPJ11
no matter how complex the task, learning effects typically diminish in importance after a limited period of time.
the initial concentrations are 0.045 M H2, 0.070 M S, and no H2S. At equilibrium, [H2] = 0.010 M. Calculate the concentrations of S and H2S at equilibrium. (Be sure to give your answers to three decimal places.) Calculate the value of K under the reaction conditions at equilibrium. (Be sure your answer has the appropriate number of significant figures.)
The reaction for the formation of hydrogen sulfide (H2S) is given by: H2(g) + S(s) ⇌ H2S(g) Initial concentrations are 0.045 M H2, 0.070 M S, and no H2S. At equilibrium, the concentration of H2 is 0.010 M.
To determine the concentrations of S and H2S at equilibrium, we need to calculate the change in concentrations. Since the stoichiometry is 1:1, the decrease in H2 concentration (0.045 - 0.010 = 0.035 M) corresponds to an equal increase in H2S concentration. Therefore, at equilibrium, [H2S] = 0.035 M. Since S is a solid, its concentration remains unchanged (0.070 M), and it doesn't affect the equilibrium constant, K. To calculate K, use the equilibrium concentrations of H2 and H2S: K = [H2S] / [H2] K = (0.035 M) / (0.010 M) K = 3.5 Under the given reaction conditions at equilibrium, the concentrations are [H2] = 0.010 M, [S] = 0.070 M, [H2S] = 0.035 M, and K = 3.5.
Learn more about hydrogen sulfide here-
https://brainly.com/question/11837837
#SPJ11
What class of chemicals is incompatible with: anhydrides, organic nitro compounds, and acids?
Acids
Bases
Oxidizing agents
Reducing agents
Anhydrides, organic nitro compounds, and acids are incompatible with reducing agent. Therefore the correct option is option D.
In a chemical reaction, reducing agents are compounds that have a propensity to transfer electrons while also becoming oxidised. Compatibility problems with reducing agents can lead to fire, explosion, the production of hazardous fumes, or the generation of heat.
Acids, anhydrides, and organic nitro compounds frequently operate as oxidising agents in chemical reactions, which means they have a propensity to receive electrons and undergo reduction. They cannot be combined with reducing agents since they would react with them and suffer oxidation, which could result in dangerous situations. Therefore the correct option is option D.
For such more question on reducing agent:
https://brainly.com/question/18370994
#SPJ11
you have made structures of nh3 and h2co molecules in the part a of your lab report. both nh3 and h2co molecules have three electron groups around the central atom. however, their molecular geometries are not the same. explain this difference.
The molecular geometry of a molecule is determined by the arrangement of its atoms in three-dimensional space. In the case of NH3 and H2CO, both molecules have three electron groups around the central atom. However, the molecular geometries of these molecules are not the same due to differences in the electronegativity and hybridization of their central atoms.
In NH3, the central nitrogen atom has three electron groups and is sp3 hybridized. The four sp3 hybrid orbitals are arranged in a tetrahedral geometry around the nitrogen atom, with the three hydrogen atoms occupying three of the four orbitals. The lone pair of electrons on the nitrogen atom occupies the fourth orbital, giving the molecule a trigonal pyramidal molecular geometry.
In contrast, the central carbon atom in H2CO also has three electron groups, but is sp2 hybridized. The three sp2 hybrid orbitals are arranged in a trigonal planar geometry around the carbon atom, with the two hydrogen atoms occupying two of the three orbitals. The remaining sp2 hybrid orbital forms a double bond with the oxygen atom, giving the molecule a bent or V-shaped molecular geometry.
Therefore, the difference in the molecular geometry of NH3 and H2CO can be attributed to differences in the hybridization and electronegativity of their central atoms.
for more such questions on molecular geometries
https://brainly.com/question/29650255
#SPJ11
Write an equation for each of the described reactions. Include subscripts, and state of matter notation as needed.
2Li(s) + 2H₂O(l) → 2LiOH(aq) + H₂(g)
Solid lithium reacts with water to produce a solution of lithium hydroxide and hydrogen gas.
2Na(s) + Cl₂(g) → 2NaCl(s)
Solid sodium reacts with gaseous chlorine to produce solid sodium chloride.
CaCO₃(s) → CO₂(g) + O₂(g) + Ca(s)
Solid calcium carbonate breaks down into carbon dioxide gas, oxygen gas, and solid calcium.
FeSO₄(s) + BaCl₂(aq) → BaSO₄(s) + FeCl₂(aq)
Solid iron(II) sulfate and a solution of barium chloride react to form solid barium sulfate and a solution of iron (II) chloride.
HCl(aq) + NaOH(aq) → H₂O(l) + NaCl(aq)
Solutions of hydrochloric acid and sodium hydroxide react to produce liquid water with sodium chloride dissolved in it.
These are the balanced chemical equations for the given reactions. Each equation shows the reactants on the left side of the arrow and the products on the right side of the arrow. Subscripts and state of matter notation are used as needed to indicate the physical properties of each substance involved in the reaction.
These chemical equations represent different types of reactions, including synthesis, decomposition, single displacement, double displacement, and acid-base neutralization. By balancing the equations, we ensure that the number of atoms of each element is the same on both sides of the equation, indicating that the law of conservation of mass is being obeyed. These equations are useful in predicting the products of a reaction and determining the amount of reactants and products involved.
The complete question is
Write an equation for each of the described reactions. Include subscripts, and state of matter notation as needed. Don't forget about the diatomic elements! *Complete this on a separate sheet of lined paper and attach this to the GCR assignment.
1. Solid lithium reacts with water to produce hydrogen gas and a solution of lithium hydroxide.
2. Solid sodium reacts with gaseous chlorine to produce sodium chloride.
3. Solid calcium carbonate breaks down into carbon dioxide gas, oxygen gas, and solid calcium.
4. Solid iron(II) sulfate and a solution of barium chloride react to form solid barium sulfate and a solution of iron (II) chloride.
5. Solutions of hydrochloric acid and sodium hydroxide react to produce liquid water with sodium chloride dissolved in it.
To know more about the Reactions, here
https://brainly.com/question/19338942
#SPJ1
A compound that is added in small amounts to make a polymer more soft and pliable is called a(n) _____.
The compound that is added in small amounts to make a polymer more soft and pliable is called a plasticizer. A polymer is a large molecule made up of repeating units.
Plasticizer is a low molecular weight substance that is added to the polymer to improve its flexibility and moldability. Plasticizers work by increasing the free volume in the polymer, which allows the polymer chains to move more easily and become more pliable.
Plasticizers are commonly used in the production of a wide range of products, including vinyl flooring, automotive parts, and medical devices. However, it's important to note that plasticizers can also have negative environmental and health effects, and there is ongoing research into developing safer alternatives.
To know more about plasticizer visit:-
https://brainly.com/question/31542885
#SPJ11
Which is listed largest to smallest?
Answer:
Nucleus, chromosome, DNA, gene
Explanation:
A gene is a part of DNA.
chromosome is made out of DNA
Chromosomes are contained inside a nucleus
During the experiment Determination of an Activation energy the decomposition of an iron (III) phenanthroline complex ion will be monitored at -----different temperature
During the experiment determining the activation energy, the decomposition of an iron (III) phenanthroline complex ion will be monitored at different temperatures.
Activation energy refers to the energy required for a chemical reaction to take place. The decomposition of the iron (III) phenanthroline complex ion involves breaking apart the complex into its individual components. By monitoring the rate of decomposition at different temperatures, the activation energy of the reaction can be determined. This information can be useful in understanding how the reaction proceeds and in optimising reaction conditions for a desired outcome.
Learn more about Activation Energy : https://brainly.com/question/5280701
#SPJ11
which of the following is a lewis acid? which of the following is a lewis acid? chbr3 nh3 alcl3 cbr4 none of the above is a lewis acid.
Among the options provided, [tex]AlCl_3[/tex], is a Lewis acid.
The Lewis acid is a species that can accept a pair of electrons, forming a new covalent bond. The Lewis base is a species that can donate a pair of electrons to form a new covalent bond.
Among the options provided, [tex]CHBr_3[/tex], [tex]NH_3[/tex], and [tex]CBr_4[/tex] are Lewis bases because they have electron-rich atoms that can donate a pair of electrons.
On the other hand, [tex]AlCl_3[/tex] is a Lewis acid because it has an incomplete octet of electrons in its valence shell and can accept a pair of electrons to form a new covalent bond. Specifically, the aluminum atom has only six electrons in its valence shell, making it electron-deficient and prone to accepting a pair of electrons from a Lewis base to complete its octet.
Therefore, the correct answer is [tex]AlCl_3[/tex], which is a Lewis acid. [tex]CHBr_3[/tex], [tex]NH_3[/tex], and [tex]CBr_4[/tex] are Lewis bases because they have atoms with lone pairs of electrons that can donate to form new covalent bonds.
In summary, a Lewis acid is a species that can accept a pair of electrons to form a new covalent bond, while a Lewis base is a species that can donate a pair of electrons to form a new covalent bond.
Thus, Among the options provided, only [tex]AlCl_3[/tex] is a Lewis acid because it has an incomplete octet of electrons in its valence shell and can accept a pair of electrons.
For more such questions on Lewis acid.
https://brainly.com/question/15570523#
#SPJ11
Which of the following indicates the least pressure?A) 1 atmB) 777 torrC) 5.5 mmHgD) 100 kPaE) 12 psi
The following that indicates the least pressure is C) 5.5 mmHg.
To compare these pressure values, let's first convert them all to a common unit, such as Pascal (Pa).
A) 1 atm = 101,325 Pa
B) 777 torr = 101,325 * (777/760) = 103,373.6 Pa (approx.)
C) 5.5 mmHg = 101,325 * (5.5/760) = 749.6 Pa (approx.)
D) 100 kPa = 100,000 Pa
E) 12 psi = 12 * 6,894.76 = 82,737.12 Pa (approx.)
Now, we can compare these values to find the least pressure:
A) 101,325 Pa
B) 103,373.6 Pa
C) 749.6 Pa
D) 100,000 Pa
E) 82,737.12 Pa
So, the least pressure is indicated by option C) 5.5 mmHg, which is approximately 749.6 Pa.
To know more about the least pressure refer here :
https://brainly.com/question/28450681#
#SPJ11
two ideal gasses have the same mass density and the same absolute pressure. one of the gasses is helium, and its temperature is 175 K. The other gas is neon (Ne). What is the temperature of the neon?
To find the temperature of neon, we can use the ideal gas law equation which states that PV = nRT, where P is the absolute pressure, V is the volume, n is the number of moles, R is the universal gas constant, and T is the temperature in Kelvin. Since both gases have the same mass density and the same absolute pressure, we can assume that they also have the same volume and number of moles.
We know that the mass density of helium is less than that of neon, which means that the same volume of helium contains fewer moles than neon. However, since the volume is the same, the number of moles must be equal for both gases. Therefore, we can use the mass density to find the number of moles of helium: mass density = mass/volume mass = mass density x volume n = mass/molar mass n(He) = (mass density of He x volume)/(molar mass of He) Similarly, we can find the number of moles of neon: n(Ne) = (mass density of Ne x volume)/(molar mass of Ne) Since both gases have the same number of moles and absolute pressure, we can equate their ideal gas law equations: PV = n(He)RT(He) = n(Ne)RT(Ne) Substituting the values, we get: P x V = [(mass density of He x volume)/(molar mass of He)] x R x 175 P x V = [(mass density of Ne x volume)/(molar mass of Ne)] x R x T(Ne) Dividing both equations, we get: T(Ne) = [(mass density of He x molar mass of Ne)/(mass density of Ne x molar mass of He)] x 175 Substituting the values, we get: T(Ne) = [(0.1785 kg/m^3 x 20.18 g/mol)/(0.9002 kg/m^3 x 4.003 g/mol)] x 175 T(Ne) = 70.5 K Therefore, the temperature of neon is 70.5 K.
Learn more about density here-
https://brainly.com/question/15164682
#SPJ11
Assuming the octet rule is obeyed; how many covalent bonds will a nitrogen atom fom t give a formal charge of zero?
Assuming the octet rule is obeyed and have a formal charge of zero, a nitrogen atom typically forms three covalent bonds with other atoms.
These bonds can be with hydrogen atoms or other elements, and the arrangement of shared electrons ensures a stable electron configuration for all atoms involved.
A nitrogen atom forms covalent bonds to achieve a formal charge of zero by adhering to the octet rule. Nitrogen has five valence electrons in its outer shell, requiring three additional electrons to complete its octet. By sharing three electrons with other atoms through covalent bonding, nitrogen can reach a stable electron configuration.
Covalent bonds involve the sharing of electrons between atoms to satisfy the octet rule. Nitrogen can form three covalent bonds, such as in ammonia (NH3), where it shares one electron with each of the three hydrogen atoms. In this case, each hydrogen atom contributes one electron, and nitrogen contributes three electrons, creating a stable, shared electron arrangement with a formal charge of zero for nitrogen.
Similarly, nitrogen can form covalent bonds with other elements to achieve a formal charge of zero. For example, in nitrogen gas (N2), two nitrogen atoms share three electrons each, resulting in a triple bond with a total of six shared electrons. Each nitrogen atom in this molecule achieves a complete octet and has a formal charge of zero.
To know more about octet rule, refer to the link below:
https://brainly.com/question/30779148#
#SPJ11
The Bromination of p-chlorophenyl isopropyl ether is to be done in a 20 liter batch reactor. Determine the time for a mixture containing 0. 02 mol of p- chlorophenyl isopropyl ether and 0. 018 mol of bromine to reach 65% conversion of p-chlorophenyl isopropyl ether given the following stoichiometry and rate expression 2A + B-> 2 C where A = p-chlorophenyl isopropyl ether, B = bromine and C = monobrominated product k1 = 2 lit/mol-min and k2 = 9200 (lit/mol)^2/min
The chemical reaction known as bromination of p-chlorophenyl isopropyl ether acts replacing a hydrogen atom on the aromatic ring of the ether molecule with a bromine atom. A Lewis acid catalyst, like aluminum bromide (AlBr₃), is typically used to initiate the reaction.
The rate law for the given reaction is:
Rate =[tex]k_1[A][B]^2[/tex]
According to the given stoichiometry, 2 moles of A respond with 1 mole of B to give 2 moles of C. In this manner, 0.02 mol of A will respond with 0.01 mol of B to give 0.02 mol of C.
We need to figure out how long it takes to convert 65 percent of A, which means that 35 percent of A won't react. As a result, at a conversion rate of 65%, the concentration of A will be:
0.35 ˣ 0.02 = 0.007mol/L
We can involve the incorporated rate regulation for the second-request response to make the opportunity taken for the given change:
t = [tex]1/((k_1/k_2)[/tex] ˣ [tex](1/[A] - 1/[A]0))[/tex]
Where,
[tex]k_1 = 2 L/mol-mink_2 = 9200 (L/mol)^2/min[/tex]
[A]0 = initial concentration of A = 0.02mol/L
[A] = concentration of A at 65% conversion = 0.007mol/L
Plugging in the values, we get:
t = [tex]1/((2/9200)[/tex] ˣ [tex](1/0.007 - 1/0.02))[/tex] = [tex]145.4[/tex]min
Therefore, the time taken for the given reaction to reach 65% conversion of p-chlorophenyl isopropyl ether is approximately 145.4 minutes.
To learn more about hydrogen atoms here
https://brainly.com/question/30886690
#SPJ4
Which factor below does not contribute to the value of the standard reduction potential for the process : Na*(aq) + e- → Na(s) a) Enthalpy change for electron attachment to Na(g) b) Enthalpy change for atomization of Na(s) c) First ionization energy of Na(g) d) Enthalpy change for hydration of Na(g)
The factor that does not contribute to the value of the standard reduction potential for the process Na×(aq) + e⁻ ⇒ Na(s) is b) Enthalpy change for atomization of Na(s).
The standard reduction potential only takes into account the enthalpy change for electron attachment to Na(g), the first ionization energy of Na(g), and the enthalpy change for hydration
The tendency of a chemical species to become reduced is referred to as standard reduction potential. Volts are measured under typical circumstances.
If a species' reduction potential is negative, it will be simple for it to lose electrons and become oxidised.
Similar to this, if a species has a positive reduction potential, it will be reduced because it will be simple to gain electrons.Compared to zinc ions, the copper ions will be decreased more quickly.
The accurate assertion is therefore that the half-reaction will be reduced more frequently the larger the standard reduction potential.
Learn more about standard reduction potential here
https://brainly.com/question/8739272
#SPJ11
All the elements of the halogen family are very reactive because they
O readily lose one valence electron
O I require only one electron to complete their outer shell
O have a high electronegativity
O form unstable gas molecules
I require only one electron to complete its outer shell. Therefore option 2 is correct.
The elements in the halogen family, including fluorine (F), chlorine (Cl), bromine (Br), iodine (I), and astatine (At), are very reactive because they require only one electron to complete their outermost electron shell.
In terms of their electron configuration, halogens have seven valence electrons, which is one electron short of a full outer shell. This electron configuration makes them highly reactive as they have a strong tendency to gain an additional electron to achieve a stable electron configuration with a full outer shell of eight electrons.
This is known as achieving a noble gas configuration, similar to the noble gases in Group 18.
In summary, the high reactivity of halogens is primarily due to their strong desire to gain one electron to complete their outermost electron shell and achieve greater stability.
Know more about halogen:
https://brainly.com/question/31220722
#SPJ12
Calculate the solubility of ZnCO3 in water at 25 °C. You'll find Ksp data in the ALEKS Data tab Round your answer to 2 significant digits
The solubility of ZnCO₃ in water at 25 °C is 6.71 * 10⁻⁶ M.
To calculate the solubility of ZnCO₃ in water at 25°C, we first need to look up the value of its solubility product constant (Ksp) in the ALEKS Data tab. The Ksp value for ZnCO₃ is 4.5 x 10⁻¹⁰ at 25°C.
The formula for the solubility of a slightly soluble salt (like ZnCO₃) is:
Ksp = [Zn²⁺][CO₃²⁻]
where [Zn²⁺] is the concentration of Zn²⁺ ions in solution and [CO₃²⁻] is the concentration of CO₃²⁻ ions in solution.
Since ZnCO₃ is a 1:1 salt, the concentrations of Zn²⁺ and CO₃²⁻ ions in solution will be equal. Let's call this concentration "x".
Therefore, Ksp = x²
Solving for x, we get:
[tex]x = \sqrt(Ksp) = \sqrt(4.5 * 10^{-10})[/tex] = [tex]6.71 * 10^{-6} M[/tex]
So the solubility of ZnCO₃ in water at 25°C is 6.71 * 10⁻⁶ M. Rounded to 2 significant digits, the answer is 6.71 * 10⁻⁶ M.
In other words, at equilibrium, the concentration of Zn²⁺ and CO₃²⁻ ions in a saturated solution of ZnCO₃ at 25°C will be approximately 6.71 * 10⁻⁶ M. Any more ZnCO₃ added to the solution will not dissolve and will remain as a solid precipitate.
To know more about solubility, refer to the link below:
https://brainly.com/question/31493083#
#SPJ11
write the half-reaction and the reaction quotient for the following: a) hydrogen gas electrode: pt(s)|h2(g)|h (aq) b) ag(s)|agcl(s)|cl-(aq) c) pt(s)|fe2 (aq), fe3 (aq) d) cu(s)|cu2 (aq)
The half-reaction describes the oxidation or reduction process that occurs at an electrode during an electrochemical reaction. It shows the transfer of electrons between the species involved in the reaction. a) Half-reaction: H2(g) → 2H+(aq) + 2e-; Reaction quotient: Q = [H+]^2 / p(H2)
b) Half-reaction: AgCl(s) + e- → Ag(s) + Cl-(aq); Reaction quotient: Q = [Ag+][Cl-] / [AgCl]
c) Half-reaction: Fe2+(aq) → Fe3+(aq) + e-; Reaction quotient: Q = [Fe3+]/[Fe2+]
d) Half-reaction: Cu(s) → Cu2+(aq) + 2e-; Reaction quotient: Q = [Cu2+]/[Cu]
The reaction quotient (Q) is a measure of the relative concentrations of the species involved in the reaction at a particular point in time, and can be used to predict the direction of the reaction (whether it will proceed forward or backward). When Q is equal to the equilibrium constant (K), the reaction is at equilibrium.
To know more about electrons
brainly.com/question/1255220
#SPJ11
Acidic
A) is an excess of OH-
B) is an excess of H+ ions
C) when alkali dissociate, anion
D) is the division of chemistry that deals with the transfer of electric charge in chemical reactions
E) loss of electrons yielding a positively charged ion
An acidic solution can be defined as one that has an excess of H+ ions .So the correct option is option B.
Acidity is a property of a substance that describes its ability to donate hydrogen ions (H+). A substance with a high concentration of H+ ions is considered acidic. In aqueous solutions, the concentration of H+ ions is balanced by the concentration of hydroxide ions (OH-). When the concentration of H+ ions is greater than the concentration of OH- ions, the solution is acidic.
Option A is incorrect because an excess of OH- ions in a solution makes it basic or alkaline, not acidic.
Option C is incorrect because the anion is not directly related to acidity. An anion is a negatively charged ion that is formed when an atom gains one or more electrons.
Option D is incorrect because electrochemistry deals with the transfer of electric charge in chemical reactions. Acidity is a broader concept that involves the concentration of H+ ions in a solution.
Option E is incorrect because the loss of electrons yielding a positively charged ion is called oxidation, which is not directly related to acidity.
Learn more about anion here:
https://brainly.com/question/20781422
#SPJ11
True or False (t or f) :
Ions exist only in the electrolyte?
The given statement "Ions exist only in the electrolyte" is false because Ions can exist in various states, including in electrolytes, in solutions, and in crystals.
When atoms or molecules gain or lose electrons, they can produce ions, which are electrically charged particles. Ions that are dissolved in a liquid or molten solvent and may conduct electricity make up an electrolyte.
Ions can participate in chemical reactions by dissolving in a solvent, like water, to form a solution.
Ions can join forces with other ions of the opposite charge to form a lattice structure in a crystal, as is the case with an ionic solid like sodium chloride (NaCl). The claim that "ions exist only in the electrolyte" is untrue as a result.
For such more question on electrolytes:
https://brainly.com/question/1581652
#SPJ11
what comes to mind when you hear the word radioactive
Answer:the act of emitting radiation spontaneously
Explanation:
How is earths surface most likely to change in a cold place that experiences rainfall
Cold regions that experience rainfall are likely to undergo surface changes such as erosion, deposition, and the formation of water bodies, leading to unique and diverse ecosystems.
In a cold place that experiences rainfall, the most likely surface changes to occur are related to erosion and deposition processes. Cold temperatures can cause water to freeze and expand, leading to the formation of cracks in rocks and soil. When these cracks are exposed to rainfall, water can penetrate and cause further erosion. Additionally, rainfall can also lead to the formation of streams and rivers, which can carve out valleys and gorges over time.
During heavy rainfall, water can accumulate in low-lying areas, leading to the formation of wetlands and lakes. Conversely, during periods of drought, these areas may dry up and form barren deserts or mudflats. In colder regions, rainfall may also contribute to the formation of glaciers, which can cause significant changes to the landscape over long periods of time.
Overall, in cold regions that experience rainfall, the most likely surface changes are related to erosion, deposition, and the formation of water bodies. These processes can significantly alter the landscape and create unique environments that support diverse ecosystems.
To learn more about rainfall
https://brainly.com/question/28576955
#SPJ4