Answer:
i. 6.923 V
ii. The e.m.f. = 22.5 V
Explanation:
i. The given parameters are;
Length of potentiometer = 1 m
The resistance of the potentiometer = 10 Ω
The e. m. f. of the attached cell = 9 V
The current, I flowing in the circuit = e. m. f/(Total resistance)
The current, I flowing in the circuit = 9 V/(10 + 3) = 9/13 A
The potential difference, p.d. across the 1 m potentiometer wire = I × Resistance of the potentiometer wire
The p.d. across the potentiometer wire = 9/13×10 = 90/13 = 6.923 V
ii) Given that the 1 m potentiometer wire has a resistance of 10 Ω, 75 cm which is 0.75 m will have an e.m.f. given by the following relation;
[tex]\dfrac{E}{R_{balance}} = \dfrac{V}{R_{cell}}[/tex]
Where:
E = e.m.f. of the balance point cell
[tex]R_{balance}[/tex] = Resistance of 75 cm of potentiometer wire = 0.75×10 = 7.5 Ω
[tex]R_{cell}[/tex] = Resistance of the cell in the circuit = 3 Ω
V = e.m.f. attached cell = 9 V
[tex]\dfrac{E}{7.5} = \dfrac{9}{3}[/tex]
E = 7.5*3 = 22.5 V
The e.m.f. = 22.5 V
A very thin film of soap, of thickness 170 nm, in between air seems dark. On the other hand, when placed on top of glass some visible light is seen to shine from the film. How can this happen and what is the smallest visible light that creates constructive interference when we place the film on top of glass
Answer:
λ₀ = 2 d n
Explanation:
A soap film is a layer where the lus is reflected on the surface and on the inside of the film, these two reflected rays can interfere with each other either constructively or destructively.
Let's analyze the general conditions of this interference,
* When the ray of light reaches the surface of the film it is reflected, as the index of refraction of the air is less than the index of the film, the reflected ray has a phase change of 180º
* When the ray penetrates the film, its wavelength changes due to the refractive index of the film.
λ = λ₀ / n
where lick is the wavelength in the vacuum or air and n index of refraction of the film, in general this interference is observed perpendicular to the film, so the sine veils 1. the expression for constructive interference taking in what previous remains
2d = (m + ½) λ
the expression for destructive interference remains
2d = m λ
2d = m λ₀ / n
When the film is placed on a glass plate whose index of refraction is greater than the index of refraction of the film, in the reflection in the lower part of the film another phase difference of 180º is created, for which we have a difference of total phase of 180 +180 = 360º, which is equivalent to no phase difference, therefore the two previous equations are interchanged.
Therefore where we had destructive interference now a cosntructive interference happens we can see the reflected light.
Find us the wavelength that this constructive interference creates
2d n = m λ₀
λ₀ = 2 d n / m
To find the minimum wavelength, suppose we observe the first interference pattern m = 1
λ₀ = 2 d n
where d is the thickness of the film and n the index of refraction of the same
1. Analogies exist between rotational and translational physical quantities. Identify the rotational term analogous to each of the following: acceleration, force, mass, work, translational kinetic energy, linear momentum, impulse.
2. Explain why centripetal acceleration changes the direction of velocity in circular motion but not its magnitude.
Answer:
1) a α, m I, W=F.d W =τ . θ,
2) a = v²/r
Explanation:
1) The amounts of rotational and translational motion are related
acceleration is
a = d²x / dt²
linear displacement is equivalent to angular rotation, therefore angular acceleration is
α = d²θ / dt²
force in linear motion is equivalent to moment in endowment motion
F = m a
τ = I α
the mass is the inertia of the translation, in rotational motion the moment of inertia is the rotational inertia
I = m r²
Work is defined by W = F. d
in rotation it is defined by W = τ . θ
The linear momentum is p = mv
the angular momentum L = I w
momentum the linear motion is I = F dt
in the rotation it is I = τ dt
2) The velocity is a vector therefore it has modulus and direction, linear acceleration changes the modulus of velocity, whereas circular motion changes the direction (the other element of the vector).
[tex]a_{c}[/tex]Ac = v²/r
A sports car moving at constant velocity travels 120m in 5.0s. If it then brakes and comes to a stop in 4.0s,what is the magnitude of it's acceleration?
✔ First calculating the speed :
V = d(in m)/t(in s)
V = 120/5 V = 24 m/s✔ You now know the average car's speed, is time it takes to stop it completely, so you can calculate its acceleration :
a = V/t
a = -24/4 a = 6 m/s² The car has an acceleration of 6 m/s².A uniform string of length 10.0 m and weight 0.32 N is attached to the ceiling. A weight of 1.00 kN hangs from its lower end. The lower end of the string is suddenly displaced horizontally. How long does it take the resulting wave pulse to travel to the upper end
Answer: 0.0180701 s
Explanation:
Given the following :
Length of string (L) = 10 m
Weight of string (W) = 0.32 N
Weight attached to lower end = 1kN = 1×10^3
Using the relation:
Time (t) = √ (weight of string * Length) / weight attached to lower end * acceleration due to gravity
g = acceleration due to gravity = 9.8m/s^2
Weight of string = 0.32N
Time(t) = √ (0.32 * 10) / [(1*10^3) * (9.8)]
Time = √3.2 / 9800
= √0.0003265
= 0.0180701s
Which reverses the flow of current through
an electric motor?
Answer:
a commutator
Explanation:
Two kilograms of nitrogen (N2) at 25°C is contained in a 0.62 m3 rigid tank. This tank is connected by a valve to a 0.16 m3 rigid tank containing 0.8 kg of oxygen (O2) at 127°C. The valve is opened, and the gases are allowed to mix, achieving an equilibrium state at 87°C.
initial pressures of N2 is 5.7293 bar and O2 is 5.2 bar.
the final pressure is 6.44 bar.
the magnitude of the heat transfer for the process is 162.8 kJ, and the direction of energy flow is going in.
What is the entropy change for the mixing process, in kJ/K?
Answer:
Explanation:
For entropy change the formula is
ΔS = ΔQ / T
ΔQ = Δ H
ΔS = Δ H / T
Given
Δ H = + 162.8 kJ
We can take equilibrium temperature as average temperature of the whole process
So, T = 273 + 87 = 360 K
ΔS = Δ H / T
= 162.8 kJ / 360
= + 0.508 kJ / K .
When the magnitude of the heat transfer for the process is 162.8 kJ, Then the entropy change for the mixing process, in kJ/K is = + 0.508 kJ / K
What is Entropy change?
For The entropy change, the formula is
Then ΔS = ΔQ / T
After that ΔQ = Δ H
Then ΔS = Δ H / T
Given as per question are:
Then Δ H = + 162.8 kJ
Now We can take equilibrium temperature as average temperature of the whole process are:
So, T is = 273 + 87 = 360 K
Then ΔS = Δ H / T
After that = 162.8 kJ / 360
Therefore, = + 0.508 kJ / K.
Find more information about Entropy change here:
https://brainly.com/question/17241209
Find the mass. 10 points. Will give brainliest.
Answer:
3.94 kgExplanation:
Given,
Force ( f ) = 30 N
Acceleration(a) = 7.6 m/s
Now, Let's find the mass of the ball
Using the Newton's second law of motion:
We get:
[tex]force \: = mass \: \times acceleration[/tex]
plug the value
[tex]30 \: = m \: \times 7.6[/tex]
Use the commutative property to reorder the terms
[tex] 30 = 7.6 \: m[/tex]
Swap the sides of the equation
[tex]7.6m = 30[/tex]
Divide both sides of the equation by 7.6
[tex] \frac{7.6 \: m}{7.6} = \frac{30}{7.6} [/tex]
Calculate
[tex]m = 3.94 \: kg[/tex]
Hope this helps..
Best regards!!
Answer:
[tex]\displaystyle \boxed{\mathrm{3.95 \: kg }}[/tex]
Explanation:
[tex]\mathrm{force \: (N) = mass \: (kg) \times acceleration \: (m/s^2)}[/tex]
[tex]\mathrm{force = 30N}[/tex]
[tex]\mathrm{acceleration = 7.6 \: m/s^2 }[/tex]
[tex]\mathrm{Find \: the \: mass.}[/tex]
[tex]\mathrm{30 = m \times 7.6}[/tex]
[tex]\displaystyle \mathrm{m =\frac{30}{7.6} }[/tex]
[tex]\displaystyle \mathrm{m = 3.947... }[/tex]
Three books are at rest, in equilibrium, on a horizontal table as
shown. The weight of each book, which is equal to the force
gravity exerts in the downward direction, is given. What is the
net force on the middle book?
Answer:
Net force = 0
Explanation:
Short answer: if the middle book is not acceleration in any direction, the net force is zero.
Long answer: refer to the attached free-body diagram (FBD) to see why the net force is zero. Skills to draw FBD are essential in solving problems in statics.
Top book exerts -mg (downwards) on the middle book.
Middle book exerts -mg (downwards) on the bottom book.
Total downward force is -mg-mg = -2mg
By Newton's third law, when an object is not in motion, reaction equals action of -2mg in the opposite direction, therefore the reaction (upwards) is +2mg.
This makes the net force of -2mg (downwards) + 2mg (upwards) =0
On a horizontal table, three books are resting and balanced. The net force on the middle book will be equal to zero.
What is equilibrium?Equilibrium is the condition of an object when two or more opposing forces, whether internal, external or a combination of both, act on the body and cancel one another out to maintain the object in the same state as it was. The Latin term for weight or balance, libra, serves as the origin of the word equilibrium.
According to the question :
The net force is 0 if the middle book does not accelerate in any direction.
The Middle book is impacted negatively (downwards) by the top book.
The middle book pulls down on the lower book by -mg.
The total downward force is -2mg = (-mg-mg)
According to Newton's third rule, a reaction when an item is not moving equals an action of -2mg in the opposite direction, hence the reaction (upwards) is a response of +2mg.
Consequently, the net force of -2mg (downwards) + 2mg (upwards) = 0 is created.
To get more information about Equilibrium :
https://brainly.com/question/28527601
#SPJ2
Question 1 of 10
What is a neutron
A. A particle inside the nucleus that has no charge
B. A positive particle inside the nucleus
O C. A negative particle outside the nucleus
O D. A negative particle inside the nucleus
Answer:
The neutron is a subatomic particle, symbol
n
or
n0
, with no electric charge and a mass slightly greater than that of a proton. Protons and neutrons constitute the nuclei of atoms. Since protons and neutrons behave similarly within the nucleus, and each has a mass of approximately one atomic mass unit, they are both referred to as nucleons.[6] Their properties and interactions are described by nuclear physics.
Explanation:
pls mark me as BRAINLIEST
8. You have two iron rods which are identical in appearance, but one is a permanent magnet and the other is unmagnetized. What series of simple experiments can you perform, using only the two rods, which will allow you to determine which of the rods is the permanent magnet
Answer:
Explanation: Let assume that bars are labeled A and B
Method 1
Using just the identical appearing bar magnet and unmagnetized iron bar.
Place the end of bar A in the middle of bar B.
If bar A sticks to bar B, then bar A is the magnet and bar B the umagnetized iron bar.
If bar A jumps to one of the ends of bar B, then bar B is the magnet.
Reason been that the magnetic field on a bar magnet is greatest at the two poles where the field comes out of the magnet. The center, between the poles, will be the weakest part of the field.
Method 2
Another solution would be to separate the two by quite some distance, float them on a piece of cork/wood in a plastic bucket or suspend them from long strings, then see which one consistently (eventually) lines up tending towards the Earth’s magnetic field.
By starting with a falsifiable hypothesis and proceeding to gather data and ensure replicability, a scientist can contribute to the potential formation of a(n)
Answer:
theory
Explanation:
A scientist can contribute to the formation of a theory in a particular subject by conducting research along the line of that subject.
Conducting research requires the formation of a hypothesis and testing the hypothesis by conducting a relevant experiment during which data are gathered, analyzed, and interpreted in order to falsify or accept the hypothesis.
A good experiment must be replicate-able. When the same experiment is repeated by different independent researchers and the same conclusion is arrived at, this could potentially lead to the formation of a theory.
Hence, a scientist can contribute to the formation of a theory by conducting an experiment with replicability in order to test a hypothesis.
Law of conservation
of momentum
Answer:
Explanation:
Law of conservation of momentum is applied in solving collision problem. When two body collides, their momentum after collision can be determined using the law.
The law States that the sum of momentum of two bodies before collision is equal to the sum of their momentum after collision. Before collision, both bodies moves with a different velocity while during some cases, the bodies moves with a common velocity after collision.
Whether they move with or without the same velocity depends on the type of collision that exists between them after the collision. After collision, some object sticks together and move with a common velocity while some doesn't.
If the bodies sticks together after collision, the type of collision that occur is inelastic (energy is not conserved) and if they splits after collision, the type of collision that occur is an elastic collision (energy is conserved).
Let m1 and m2 be the masses of the bodies
u1 and u2 be their velocities before collision
v1 and v2 be their velocities after collision.
According to the law;
m1u1 + m2u2 = m1v1 + m2v2
Note that momentum = mass × velocity of the body.
A carpenter measured the lengeth of a small piece of timber as 24.6cm .Calculate the relative error in the measurement if the true length is 24.5cm
ANSWER:
0.4081%
Explanation:
Difference=24.6-24.5=0.1
Relative error = 0.1/24.5*100=0.4081%
Relative error is equal to the = difference between both the values/The true value *100
formula of minimmum pressure
Answer:
pressure=force/area
Ozone molecules in the stratosphere absorb much of the harmful radiation from the sun. How many ozone molecules are present in 2.00 L of air under the stratospheric ozone conditions of 275 K temperature and 1.89 × 10−3 atm pressure?
Answer:
1.01×10^20 molecules of ozone.
Explanation:
Data obtained from the question include:
Volume (V) = 2 L
Temperature (T) = 275 K
Pressure (P) = 1.89×10¯³ atm
Gas constant (R) = 0.0821 atm.L/Kmol
Number of mole (n) of ozone =.?
Using the ideal gas equation, we can obtain the number of mole of ozone as follow:
PV = nRT
1.89×10¯³ x 2 = n x 0.0821 x 275
Divide both side by 0.0821 x 275
n = (1.89×10¯³ x 2) /(0.0821 x 275)
n = 1.67×10¯⁴ mole.
Therefore the number of mole of ozone in 2 L of air is 1.67×10¯⁴ mole.
Finally, we shall determine the number of molecules present in 1.67×10¯⁴ mole of ozone.
This can be obtained as follow:
From Avogadro's hypothesis, 1 mole of any substance contains 6.02×10²³ molecules. This implies that 1 mole of ozone contains 6.02×10²³ molecules.
If 1 mole of ozone contains 6.02×10²³ molecules,
therefore, 1.67×10¯⁴ mole of ozone will contain = 1.67×10¯⁴ x 6.02×10²³ = 1.01×10^20 molecules.
Therefore, 1.01×10^20 molecules of ozone are present in 2 L of air.
a skydiver jumped out of a plane and fell 9 miles to the ground. his average speed while falling was 174 miles/hour. how much time did the dive last?
Answer:
t = 0.051 seconds
Explanation:
Given that,
A skydiver jumped out of a plane and fell 9 miles to the ground. It means 9 miles is the distance covered.
The average speed of the skydiver is 174 miles/hour
We need to find the time for which he dive last. It means t is the time taken. Total distance covered divided by time taken is called average speed. So,
[tex]v=\dfrac{d}{t}\\\\t=\dfrac{d}{v}\\\\t=\dfrac{9}{174}\\\\t=0.051\ s[/tex]
So, a skydiver dive for 0.051 seconds.
Janaki Temple and Pashupatinath Temple are increasing our pride how
Answer:
Janaki temple and Pashupatinath Temple are found in Nepal. These structures are religious and they increase the pride of the country through tourism. These temples are important in the country and are mostly visited by tourists.
This also helps to bring in income for the country and also helps by attracting many visitors and a corresponding development of its tourism industry.
Which statement describes one feature of a closed circuit? Charges do not flow. Bulbs will not shine. The circuit is broken. The circuit is complete.
I inferred you've referring to a close electrical circuit.
Answer:
The circuit is complete.
Explanation:
A closed electrical circuit is indeed a complete circuit. Also, it allows charges to flow, the bulbs in the circuit will shine and it is not broken.
It is termed closed circuit because there is no brokage in the series of electrical wires or the switch; which may prevent the free flow of current or charges. Thus, a feature that marks closed circuits is that they are complete.
Answer:
The circuit is complete.
Explanation:
How does increasing frequency affect the crests of a wave?
They get higher.
They get closer together.
They get lower.
They get farther apart.
Answer:
they get closer together
Explanation:
What happens when white light shines through a translucent, red, glass window? a) All colors of light except red are transmitted through the glass. b) Red light is transmitted through and reflected by the glass c) Red light is absorbed by the glass d) all colors except red are reflected by the glass
Answer:
b. Red light is transmitted through and reflected by the glass
Explanation:
Give me brainliest plz!
All of the wavelengths of the red light are absorbed when it passes through a translucent red glass window, but the red light is transmitted and reflected.
What happens when white light shines through red glass?Red light emerges from the other side of a white light source that has been passed through a red filter. This is so that only red light can pass through the red filter. The spectrum's other colors (wavelengths) are absorbed. Similar to this, a green filter only lets through green light.White light is colorless light that contains all the wavelengths of the visible spectrum. Only specific wavelengths of white light are filtered through transparent or translucent things.Through a colorful glass, white light shines through. Except for the color it is shining through, all light wavelengths are absorbed by the glass.Therefore, if the red light passes through a translucent, red, glass, window, all the wavelengths are absorbed but the red light is transmitted and reflected.
Therefore, the correct answer is option b) Red light is transmitted through and reflected by the glass.
To learn more about light refer to:
https://brainly.com/question/12002703
#SPJ2
A plane drops a package for delivery. The plane is flying horizontally at a speed of 120m/s,and the package travels 255 m horizontally during the drop. We can ignore air resistance.What is the package's vertical displacement during the drop?
Answer:
Package's vertical displacement(s) = 22.12 meter
Explanation:
Given:
Speed of plane = 120 m/s
Total distance = 255 m
Find:
Package's vertical displacement(s)
Computation:
Time taken = Distance / Speed
Time taken = Total distance / Speed of plane
Time taken = 255 / 120
Time taken = 2.125 s
Acceleration due to gravity(g) = 9.8 m/s²
Initial velocity (u) = 0
So,
Package's vertical displacement(s) = ut + (1/2)gt²
Package's vertical displacement(s) = (0)(2.125) + (1/2)(9.8)(2.125)²
Package's vertical displacement(s) = 22.12 meter
Answer: -22.1
Explanation:
I just did the Khan Academy and that was the answer, not the one provided by that one person. :)))
Calculating heat gained, need help!!!
Q=(m)(c)(triangle T)
trial 1:
Q=(0.4)(4.186 J/kg)(78)=?
trial 2:
Q=(0.6)(4.186 J/kg)(78)=?
trial 3:
Q=(0.45)(4.186 J/kg)(75)=?
Explanation:
q = mCΔT
where m is mass,
C is specific heat capacity,
and ΔT is change in temperature.
Make sure all your units match. Assuming the substance is water, C = 4186 J/kg/°C.
Trial 1:
q = (0.4 kg) (4186 J/kg/°C) (78°C)
q = 130,600 J
Trial 2:
q = (0.6 kg) (4186 J/kg/°C) (78°C)
q = 195,900 J
Trial 3:
q = (0.45 kg) (4186 J/kg/°C) (75°C)
q = 141,300 J
Which of the following object is in dynamic equilibrium?
Answer:
A car driving in a straight line 20 m/s
Explanation:
ayepecks silly
A car engine burns gas at 495 K and exhausts to the air at 293 K. What is the highest possible efficiency it could have?
(NO UNIT)
Answer:
59.19%
Explanation:
Step 1:
Data obtained from the question. This include the following:
Input temperature = 495 K.
Output temperature = 293 K.
Efficiency =..?
Step 2:
Determination of the efficiency of the engine.
Efficiency is simply defined as the ratio of output to input times 100. Mathematically, it is expressed as:
Efficiency = output /input x 100
With the above formula, we can calculate the efficiency of the engine as follow:
Input temperature = 495 K.
Output temperature = 293 K.
Efficiency =..?
Efficiency = output /input x 100
Efficiency = 293/495 x 100
Efficiency = 59.19%
Therefore, the efficiency of the engine is 59.19%
Answer:
0.41
Explanation:
Trust me bro
A 24 cm radius aluminum ball is immersed in water. Calculate the thrust you suffer and the force. Knowing that the density of aluminum is 2698.4 kg / m3
Answer:
W =1562.53 N
Explanation:
It is given that,
Radius of the aluminium ball, r = 24 cm = 0.24 m
The density of Aluminium, [tex]d=2698.4\ kg/m^3[/tex]
We need to find the thrust and the force. The mass of the liquid displaced is given by :
[tex]m=dV[/tex]
V is volume
Weight of the displaced liquid
W = mg
[tex]W=dVg[/tex]
So,
[tex]W=dg\times \dfrac{4}{3}\pi r^3\\\\W=2698.4\times 10\times \dfrac{4}{3}\times \pi \times (0.24)^3\\\\W=1562.53\ N[/tex]
So, the thrust and the force is 1562.53 N.
Can someone please help me?
An alien spaceship is 650 m above the ground and moving at a constant velocity of 175 m/s upwards.
How high above the ground is the ship after 5 seconds?
Answer:
1525 meters above ground
Explanation:
So to do this you will need to write this in slope intercept form or [tex]y=mx+b[/tex]. So 650 would be the b, 175 would be the m, and the x would be 5 so the equation would be [tex]y=175(5)+650[/tex] so if you solve or simplify the equation you will get 1525 meters above the ground and that would be our final answer.
A wall in a house contains a single window. The window consists of a single pane of glass whose area is 0.15 m2 and whose thickness is 7 mm. Treat the wall as a slab of the insulating material Styrofoam whose area and thickness are 17 m2 and 0.20 m, respectively. Heat is lost via conduction through the wall and the window. The temperature difference between the inside and outside is the same for the wall and the window. Of the total heat lost by the wall and the window, what is the percentage lost by the window
Answer:
88 %
Explanation:
The rate of heat loss by a conducting material of thermal conductivity K, cross-sectional area,A and thickness d with a temperature gradient ΔT is given by
P = KAΔT/d
The total heat lost by the styrofoam wall is P₁ = K₁A₁ΔT₁/d₁ where K₁ =thermal conductivity of styrofoam wall 0.033 W/m-K, A₁ = area of styrofoam wall = 17 m², ΔT₁ = temperature gradient between inside and outside of the wall and d₁ = thickness of styrofoam wall = 0.20 m
The total heat lost by the glass window is P₂ = K₂A₂ΔT₂/d₂ where K₂ =thermal conductivity of glass window pane wall 0.96 W/m-K, A₂ = area of glass window pane = 0.15 m², ΔT₂ = temperature gradient between inside and outside of the window and d₂ = thickness of glass window pane = 7 mm = 0.007 m
The total heat lost is P = P₁ + P₂ = K₁A₁ΔT₁/d₁ + K₂A₂ΔT₂/d₂
Now, since the temperatures of both inside and outside of both window and wall are the same, ΔT₁ = ΔT₂ = ΔT
So, P = K₁A₁ΔT/d₁ + K₂A₂ΔT/d₂
Since P₂ = K₂A₂ΔT₂/d₂ = K₂A₂ΔT/d₂is the heat lost by the window, the fraction of the heat lost by the window from the total heat lost is
P₂/P = K₂A₂ΔT/d₂ ÷ (K₁A₁ΔT/d₁ + K₂A₂ΔT/d₂)
= 1/(K₁A₁ΔT/d₁÷K₂A₂ΔT/d₂ + 1)
= 1/(K₁A₁d₂÷K₂A₂d₁ + 1)
= 1/[(0.033 W/m-K × 17 m² × 0.007 m ÷ 0.96 W/m-K × 0.15 m² × 0.20 m) + 1]
= 1/(0.003927/0.0288 + 1)
= 1/(0.1364 + 1)
= 1/1.1364
= 0.88.
The percentage is thus P₂/P × 100 % = 0.88 × 100 % = 88 %
The percentage of heat lost by window of the total heat is 88 %
Velocity is a description of an object’s blank
Velocity is the description of an object's motion from one point to another.
It tells the speed with which the trip is completed, and the direction from the start-point to the end-point. It tells nothing about any twists, turns, loops, bends, or stops along the way.
Imagine that your standing on a beach but cannot swim. Your friend encourages you to walk into the surf zone created by incoming deep-water waves that have a wavelength of 30 meters. Would it be safe to walk out to where the waves are breaking? Explain how you arrived at your answer.
Answer:
It would not be safe to walk out to where waves are breaking due to the effect of rip currents
Explanation:
The water depth in the surf zone is between 5 to 10 meters deep and with a wavelength of 30 meters, the speed of the wave is considerably fast such that control for safety may be difficult
Also the speed of the wave is directly related to the depth of the water which means that where the wave described above is fast as well as the rip current, also the water depth is expected to be considerable for a non swimmer
It is best to seek for sign post regarding safe areas and do not go into the water where there are no lifeguards or marked safe zones.
It won't be safe to walk out to where the waves are breaking.
This is because the wavelength is 30 meters which is a characteristic of
areas with significant water depth in the range of 5-11 meters.Under these
conditions the waves are usually very fast and may get swept with the
current from the water waves when trying to run from it.
It is recommended that we stay in areas where the depth is noted as not
being much and should always seek help and clarity from the life guards so
as to prevent drowning and death.
Read more on https://brainly.com/question/17125479
We have seen that starlight passing through the interstellar medium is dimmed and reddened. Look at the photo of a sunset on Earth. The Sun’s light also appears reddish at sunset. Given your understanding of the reddening of starlight, why do you think sunsets appear red?
Answer:
Explanation:
Reddening of sun's rays at sunset and sunrise is due to scattering of light . The white light consisting of seven colours coming from the sun are scattered in different directions when they fall on the air particles present in atmosphere . Red coloured light scatters least and it travels straight forward to the viewer on the earth . On the other hand other colours scatter most and therefore they go out of area of vision for the viewer on the earth . Since only red colour reaches the eye of the viewer , sun's ray appear red . This happens during sunrise and sunset . It is so because during this period , sun rays travel far greater distance through atmosphere , so scattering is most pronounced .