There are two lengths of the Position Indicator Device (PID): 18 inches and 24 inches.
The Position Indicator Device (PID) is a tool used in industrial applications to show visually where a valve or damper is located. HVAC systems, power plants, and other industrial environments are where it is most frequently employed. There are two lengths of the PID: 18 inches and 24 inches. The size of the valve or damper being controlled, as well as the particular application, will determine the length of the PID that is necessary. The PID is a crucial element of industrial control systems, and one of the things that must be taken into account when developing and implementing these systems is its length.
learn more about PID here:
https://brainly.com/question/17032153
#SPJ11
Using your knowledge of metric units, English units, and the information on the back inside cover, write down the con- version factors needed to convert (a) mm to nm, (b) mg to kg, (c) km to ft, (d) in
To convert millimeters (mm) to nanometers (nm), we need to multiply by 1,000,000. This is because there are 1,000,000 nanometers in one millimeter. Therefore, the conversion factor is 1 mm = 1,000,000 nm.\
To convert milligrams (mg) to kilograms (kg), we need to divide by 1,000,000. This is because there are 1,000,000 milligrams in one kilogram. Therefore, the conversion factor is 1 mg = 0.000001 kg.To convert kilometers (km) to feet (ft), we need to multiply by 3280.84. This is because there are 3280.84 feet in one kilometer. Therefore, the conversion factor is 1 km = 3280.84 ft.To convert inches (in) to centimeters (cm), we need to multiply by 2.54. This is because there are 2.54 centimeters in one inch. Therefore, the conversion factor is 1 in = 2.54 cm.
To learn more about nanometers click on the link below:
brainly.com/question/30575178
#SPJ11
The prestressing steel in the free length area is protected by
Hello! The prestressing steel in the free length area is protected by a corrosion-resistant covering, typically consisting of a combination of grease, plastic sheathing, and cementitious grout. The primary purpose of this protection is to shield the steel from harmful environmental factors and ensure its durability and long-term performance.
Prestressing steel is a key component of pre-tensioned and post-tensioned concrete structures. It is made from high-strength steel strands or bars that are tensioned before or after the concrete is cast, creating compressive stress in the concrete, which enhances its load-bearing capacity.
Grease serves as a barrier against moisture and air, preventing rust and corrosion on the steel surface. The plastic sheathing is an additional layer of protection that encapsulates the prestressing steel, creating a robust barrier against physical damage and external influences. Lastly, cementitious grout is used to fill the voids around the prestressing steel, providing a solid, durable layer that adheres well to both the plastic sheathing and the surrounding concrete.
In summary, the protection of prestressing steel in the free-length area is essential to maintain the integrity, strength, and performance of pre-tensioned and post-tensioned concrete structures. This protection is achieved through a combination of grease, plastic sheathing, and cementitious grout, which work together to guard against corrosion and damage.
Learn more about prestressing here:
https://brainly.com/question/29308208
#SPJ11
1. Show a list of Customer Name, Gender, Sales Person Name and Sales Person's City for all products sold on September 2015, whose Sales Price is more than 20 and Quantity sold is more than 8.
2. Show a list of Store Name, Store's City and Product Name for all products sold on March 2017, whose Product Cost is less than 50 and store located in 'Boulder'.
3. Show a list of Top 2 Sales Person by their Total Revenue for 2017, i. E. Top 2 sales person with HIGHEST Total Revenue.
4. Display a Customer Name and Total Revenue who has LOWEST Total Revenue in 2017.
5. Show a list of Store Name (in alphabetical order) and their 'Total Sales Price' for the year between 2010 and 2017
Since the list of Customer Name cannot be shown its can be displayed by the use of SQL query structure.
What is the SQL query?The query joins three tables (Sales, Customers, and SalesPersons) using SQL's JOIN clause and filters the results using WHERE clauses based on specified criteria. Note that syntax and names may differ based on your database schema. Modify the query to fit your structure.
The inquiry uses SQL's Connect clause to connect the important tables based on their essential and outside keys, and after that employments WHERE clauses to filter the comes about based on the desired criteria, such as the deals date, sales price, and amount sold.
Learn more about SQL query from
https://brainly.com/question/27851066
#SPJ4
What Number Follows 777 When Counting In A. Decimal; B. Octal; C. Hexadecimal?
We can deduce here that the number that follows 777 are:
A. Decimal: The number that follows 777 in decimal counting is 778.
B. Octal: The number that follows 777 in octal counting is 1000.
C. Hexadecimal: The number that follows 777 in hexadecimal counting is 778.
What is decimal?Each digit in a number indicates a multiple of a power of 10, making decimal a base-10 number system used in mathematics and computer science.
Any number can be represented using the 10 digits of the decimal system, which range from 0 to 9.
The decimal system is frequently utilized in daily life for computations, measurement, and counting. It is also the most widely used number system in computers and programming languages, where actual numbers and monetary values are frequently represented by it.
Learn more about decimal on https://brainly.com/question/703656
#SPJ4
solidworkds you can fully define the shape and size of a sketch using only dimensions and geometric relations.
Yes, in SolidWorks, you can fully define the shape and size of a sketch using only dimensions and geometric relations.
These dimensions and relations allow you to control the exact placement and orientation of each element within the sketch, ensuring that it meets your design requirements. By defining the sketch in this way, you can easily make changes to the design by simply adjusting the dimensions and relations, rather than having to recreate the entire sketch from scratch. This makes SolidWorks a powerful tool for creating precise and accurate 3D models.
To learn more about geometric relations visit;
https://brainly.com/question/15069391
#SPJ11
The strength reduction factor for a concrete section controlled by flexure is 0.9 where for shear it is 0.75, what is best explanation for the reason between the different factors.
O Shear reinforcement (stirrups) are cheaper than longitudinal reinforcement hence we can afford a larger strength reduction without substantially affecting the cost.
O There are more concrete failures via shear than there are for flexure, hence a greater strength reduction is warranted to ensure public safety.
O The behavior of a concrete member exposed to shear is better understood than for flexure
O A concrete member that fails via flexure will provide greater warning signs of the overload than if it fails by shear,
The reason for the different strength reduction factors for a concrete section controlled by flexure and shear is due to the behavior of the concrete member under these two conditions. When a concrete member is subjected to flexure, the failure occurs primarily due to the yielding of the longitudinal reinforcement.
Hence, a strength reduction factor of 0.9 is sufficient to ensure the safety of the structure as it provides a factor of safety against failure.
On the other hand, when a concrete member is subjected to shear, the failure occurs due to the crushing of concrete before the reinforcement yields. Therefore, the design must include sufficient shear reinforcement to prevent premature failure of the concrete member. The use of stirrups or shear reinforcement is cheaper than the use of longitudinal reinforcement, and hence, a strength reduction factor of 0.75 is appropriate for shear-controlled sections.
In conclusion, the different strength reduction factors for a concrete section controlled by flexure and shear are based on the failure mechanisms of the concrete member. It is essential to consider these factors to ensure the safety and stability of the structure.
Learn more about reduction here:
https://brainly.com/question/14698511
#SPJ11
The frame supports a centrally applied distributed load of 1. 8 kip/ft. Determine the state of stress at points A and B on member CD and indicate the results on a volume element located at each of these points. The pins at C and D are at the same location as the neutral axis for the cross section
The total stress is given as 44.623
How to solve for the stressFind the moment at c
= 3 / 5 * 16 - 1.8 * 16 * 16/2
= 24
shear force at A and B
-24 * 3/5 + 1.8 * 11
= 5.4
24 x 4 / 5
= 19.2 Kip
M = 24 * 3/5 * 11 - 1.8 * 11 * 11 / 2
= 49.5 Kip
Find the centroid
The value of the centroid is 5.39 from B and it is 2.11 from point A
Find the moment of In ertia around X axis
This is given as 73.66 in ⁴
Normal stress at A
19.2 / 1 x 6 + 7 x 1.5
= 1.163 ksi
49.5 x 12 x 5.39 / 73.66
= 43.46
The total stress at the point B
= 1.163 ksi + 43.46
= 44.623
The total stress is given as 44.623
Read more on stress loads here:https://brainly.com/question/13323387
#SPJ4
A real length of 1 decametre is represented by a line of 5 cm in a drawing find the r.f
The real length of 1 decametre is 10 meters or 1000 centimeters.
In the drawing, a line of 5 cm represents this length.
To find the RF (Representative Fraction), we can use the formula:
RF = (Length on drawing) / (Corresponding length in real life)RF = 5 cm / 1000 cmRF = 1/200ANSWERRF = 1/200.a multi-floor collapse in which several floor slabs completely fail and then stack on top of each other. is known as ??
A multi-floor collapse in which several floor slabs completely fail and then stack on top of each other is known as a pancake collapse.
A pancake collapse refers to a type of building collapse where multiple floors of a building fail in sequence and stack on top of each other, creating a pile of collapsed floors resembling a stack of pancakes. This type of collapse is typically associated with buildings constructed with lightweight materials, such as concrete slabs, and can be triggered by events such as earthquakes, explosions, or structural failure. The pancake collapse can be particularly devastating as the weight of the collapsed floors can cause further damage to the remaining parts of the building and hinder rescue and recovery efforts.
Learn more about fed's policy here:
https://brainly.com/question/16860555
#SPJ11
The multi-floor collapse in which several floor slabs completely fail and stack on top of each other is known as a pancake collapse.
What is the term for the multi-floor collapse?This type of collapse referred to as a pancake collapse occurs when multiple floor slabs fail simultaneously and collapse resulting in a stack-like formation. This phenomenon is typically associated with structural failures and can have catastrophic consequences.
The stacking of the floor slabs reduces the space between them, making it extremely difficult for anyone trapped within the collapsed structure to survive or be rescued. The pancake collapse is a significant concern in building safety and structural engineering as it highlights the importance of robust design and proper construction techniques.
Read more about pancake collapse
brainly.com/question/541986
#SPJ4
What are the two main types of gravity pipe systems you can design with Civil 3D?
answer:
stormwater management system and sanitary sewer system
explanation:
a stormwater management system is designed to handle rainfall and runoff from impervious surfacesa sanitary sewer system is designed to transport wastewater from homes, businesses, and other sources to a treatment plant for processingThe two main types of gravity pipe systems that can be designed with Civil 3D are:
1) Pressure pipe system - This type of system is used to design and analyze pipes that are under pressure, such as water supply systems. The pipes are designed to withstand the pressure and flow of the fluid being transported.
2) Gravity pipe network - This type of system is used to design and analyze pipes that rely on gravity to transport fluids, such as stormwater drainage systems. The pipes are designed to follow the natural slope of the land and gravity to move the fluid from higher elevations to lower elevations.
Learn more about pipe system: https://brainly.com/question/30365511
#SPJ11
Which of the following is true for partition-based clustering but not hierarchical nor density based clustering algorithnis? a) Partition-based clustering produces sphere-like clusters. b) Partition-based clustering can handle spatial clusters and noisy data. c) Partition-based clustering produces arbitrary shaped clusters. d) Partition-based clustering is a type of unsupervised learning algorithm.
True. Agglomerative hierarchical clustering procedures are better able to handle outliers than k-means.
Are agglomerative hierarchical clustering procedures better at handling outliers than k-means? (True/False)
1. Agglomerative hierarchical clustering procedures are better able to handle outliers than k-means. [True] - Agglomerative hierarchical clustering is more robust to outliers because it builds clusters by merging them based on proximity, whereas k-means can be influenced by outliers due to the mean calculation.
2. Different runs of k-means can produce different clusterings, but agglomerative hierarchical clustering procedures will always produce the same clustering. [False] - Both k-means and agglomerative hierarchical clustering can produce different clusterings in different runs due to their random initialization or tie-breaking mechanisms.
3. When clustering a dataset using k-means, SSE (Sum of Squared Errors) is guaranteed to monotonically decrease as the number of clusters increases. [False] - Increasing the number of clusters in k-means can sometimes lead to higher SSE values as the algorithm may overfit the data.
4. For a dataset that contains a density-based notion of clusters, a measure of cohesion can show poor values on the true clusters. [True] - Density-based clustering algorithms may struggle to accurately measure cohesion in datasets with irregular cluster shapes or varying densities.
5. The SSE of the k-means clustering algorithm keeps reducing with every iteration. [True] - In each iteration of k-means, the SSE is minimized by updating the cluster centroids and reassigning points, leading to a reduction in SSE.
6. The lowest value of SSE for the k-means algorithm is obtained when k=n, the number of points in the data. [True] - When the number of clusters equals the number of points, each point becomes a separate cluster, resulting in SSE equal to 0.
7. If a cluster is split by picking one of the points as a new centroid and reassigning points to the original or new centroid, the SSE of the clustering would only decrease. [False] - Splitting a cluster can increase the SSE if the new centroid leads to a worse assignment of points, resulting in higher squared errors.
Learn more about hierarchical clustering on:
brainly.com/question/29769638
#SPJ12
what are the estimated values of the endurance limits for the 4340 and 1040 steels? the endurance limit for the 4340 steel is kpsi. the endurance limit for the 1040 steel is
The 1040 steel, its endurance limit is typically lower than that of 4340 steel due to its lower carbon content and lower strength.
The estimated endurance limit for 4340 steel varies depending on the heat treatment and surface conditions.
Generally, it falls within the range of 50-120 ksi (kilo-pounds per square inch), with typical values around 80 ksi for a fully annealed condition.
The estimated endurance limit for 1040 steel is typically in the range of 30-70 ksi, with typical values around 45 ksi for a fully annealed condition.
It's important to note that these are estimated values and can vary depending on factors such as the material's heat treatment, surface condition, and loading conditions.
Actual values for endurance limits should be determined through testing specific to the application.
Depending on the surface characteristics and heat treatment, 4340 steel's projected endurance limit varies.
It typically ranges from 50 to 120 ksi (kilo-pounds per square inch), with completely annealed steel often registering values of about 80 ksi.
For completely annealed steel, the predicted endurance limit is normally in the range of 30-70 ksi, with average values being about 45 ksi.
It's vital to keep in mind that these are only estimates and may change based on the heat treatment, surface quality, and loading conditions of the material.
Actual endurance limitations should be established by application-specific testing.
For similar questions on Endurance
https://brainly.com/question/15282669
#SPJ11
After approval is given by the engineer of record, tendon tails in an encapsulated system must be cut off
In the construction industry, particularly when working with post-tensioned concrete structures, the engineer of the record plays a critical role in ensuring that all components and systems are properly designed, constructed, and functioning as intended. One aspect of this process involves the handling of tendon tails in an encapsulated system.
After the engineer of record has given approval, tendon tails in an encapsulated system must be cut off. This is an essential step in the post-tensioning process to ensure structural stability, maintain proper functioning, and prevent potential issues down the line. Cutting the tendon tails helps reduce stress concentrations, mitigates the risk of corrosion, and ensures a smooth and flush surface on the concrete structure.
During this process, it is crucial to follow the guidelines and recommendations provided by the engineer of record. Their expertise and knowledge of the specific project requirements ensure that the cutting of tendon tails is carried out safely, efficiently, and in accordance with relevant codes and standards.
In summary, cutting off tendon tails in an encapsulated system is a vital step in the post-tensioning process once approval has been granted by the engineer of record. This action contributes to the overall structural stability and longevity of the concrete structure while minimizing potential risks associated with stress concentrations and corrosion.
Learn more about engineer here:
https://brainly.com/question/19117846
#SPJ11
Stressing jacks and gauges should be calibrated at intervals not exceeding __ months
Stressing jacks and gauges are essential tools in the construction and engineering industry, used for measuring the tension and compression forces in various structures. It is crucial that these instruments are calibrated regularly to ensure that they provide accurate readings.
According to industry standards and regulations, stressing jacks and gauges should be calibrated at intervals not exceeding six months. This is necessary to maintain the accuracy and reliability of the instruments and to ensure that the structures being tested are safe and secure. Calibration involves comparing the readings of the instrument to a known standard to determine its accuracy and to adjust it if necessary.
It is also important to note that the calibration of these instruments should only be carried out by trained and certified professionals who have the necessary knowledge and expertise. Any calibration deviations should be documented, and the instruments should not be used until they are recalibrated and verified to be within acceptable limits.
In summary, regular calibration of stressing jacks and gauges is essential to maintain their accuracy and ensure that the structures being tested are safe and secure. The recommended calibration interval is not exceeding six months, and the calibration should only be performed by trained and certified professionals.\
Learn more about jacks here:
https://brainly.com/question/506622
#SPJ11
Kiera wondered, "How much was my last paycheck for?
Answer: No
Explanation: If you were asking for statistical question
A radar system is characterized by the following parameters: P_t = 1 kW, tau = 0. 1 mu s, G = 30 dB, lambda = 3 cm, and T_sys = 1, 500 K. The radar cross section of a car is typically 5 m^2. How far away can the car be and remain detectable by the radar with a minimum signal-to-noise ratio of 13 dB? What is the minimum PRF to assure that we can measure the car at this distance?
With this radar system in place, at what distance will a car with a radar detector that has the following parameters G = 30 dB, lambda = 3 cm, and T_sys = 1, 500 K be able to detect the radar signal?
The minimum PRF to assure that we can measure the car at this distance is 21.1 km.
What is a Radar System?Radar systems employ radio waves to locate and detect objects in their immediate vicinity. These innovative pieces of technology analyze the reflections bouncing back from items, following transmission of a radio wave signal.
How to solve:
To calculate the maximum detection range, we will use the radar range equation:
R_max =[tex][(P_t * \tau * G^2 * \lambda^2 * \sigma) / (64 * pi^3 * k * T_s_y_s * SNR_m_i_n)]^(^1^/^4^)[/tex]
Where:
P_t = 1 kW = 1000 W (transmitted power)
tau = 0.1 µs = [tex]0.1 * 10^(^-^6^)[/tex] s (pulse duration)
G = [tex]10^(^3^0^/^1^0^)[/tex](antenna gain in linear units)
lambda = 3 cm = 0.03 m (wavelength)
sigma = [tex]5 m^2[/tex] (radar cross section of the car)
k = [tex]1.38 * 10^(^-^2^3^) J/K[/tex] (Boltzmann constant)
T_sys = 1500 K (system temperature)
SNR_min = [tex]10^(^1^3^/^1^0^)[/tex] (minimum signal-to-noise ratio in linear units)
R_max ≈ 21.1 km
To find the minimum PRF, we need to use the following relationship:
PRF_min = c / (2 * R_max)
Where c = [tex]3 * 10^8 m/s[/tex] (speed of light).
PRF_min ≈ 7102 Hz
For the car with a radar detector, we will use the same radar range equation, but this time, we will solve for the SNR:
[tex]SNR_c_a_r = (P_r * 64 * \pi^3 * k * T_s_y_s) / (G^2 * \lambda^2 * \sigma)[/tex]
Where P_r is the received power at the car's radar detector. Since the radar detector has the same G, lambda, and T_sys values, we can reuse the R_max value:
SNR_car ≈ [tex]10^(^1^3^/^1^0^)[/tex]
The car with the radar detector can detect the radar signal at a distance of approximately 21.1 km.
Read more about radar here:
https://brainly.com/question/1073374
#SPJ4
Every refresh load will always take more time than the first load. True or False
False. Refreshes are quicker. Only the most recently altered data needs to be refreshed.
What is a Refresh in computing?Reloading or updating what is displayed or stored is referred to as refreshing. If you are on a web page, for example, refreshing the page reveals the most recent content published on that page.
Essentially, you're requesting the site to transfer the most recent version of the page you're viewing to your computer.
It reads the contents of a dynamic memory device and then rewrites it. This is done to ensure that the information in RAM does not vanish.
Learn more about Refresh here:
https://brainly.com/question/30286853
#SPJ4
Estimate the maximum velocity & the maximum mach number of the cj-1 flying at sea level. Note that sea level speed of sound is 1,117 ft/sec 8. Estimate the maximum r/c of the cj-1 flying at sea level
The maximum velocity based on the information given will be 980 feet per second.
What is maximum velocity?Maximum velocity is defined as the greatest speed an entity can possibly reach in a certain system or situation. This maximum rate of motion is dependent upon multiple factors such as the mass, applied force, and resistance encountered by the object, plus even the environment it is traversing.
When considering classical mechanics, the maximum velocity of an article is calculated via the given equation v = √2*E/m, with v representing its velocity, E standing for its energy, and m signifying its mass.
Based on the information, maximum velocity can be found by using TR , TA vs V curve. The intersection point gives Vmax = 980ft/s (approx)
Learn more about velocity on
https://brainly.com/question/30505958
#SPJ4
Suppose we have 2^10 bytes of virtual memory and 2^8 of physical mian memory. Suppose page size is 2^4 bytes.
a)how many pages are there in virtual memory?
b)how many page frames are there in main memory?
c)how many entries are in the page table for a process that uses all of virtual memory??
figure 1 illustrates hanger casting, which is subjected to the tensile load along the line connected by centers of its two hole a and b
Based on the information provided, figure 1 appears to depict a hanger casting that is experiencing a tensile load.
This load is applied along the line that connects the centers of the two holes labeled "a" and "b". It is important to note that when a material is subjected to a tensile load, it experiences a force that pulls it apart along the axis of the load. In the case of the hanger casting, this means that the material is being stretched along the line connecting the centers of the holes. Understanding the type of load and direction of force acting on a material is important for determining its strength and ability to withstand such loads.
To learn more about tensile visit;
https://brainly.com/question/14293634
#SPJ11
an air-conditioning system operating on the reversed carnot cycle is required to transfer heat from a house at a rate of 750 kj/min to maintain its temperature at 24oc. if the outdoor air temperature is 35oc, determine the power required [kw] to operate this air-conditioning system.
The power required to operate this air-conditioning system is approximately 0.463 kW.
How to calculate the power required to operate the systemTo determine the power required to operate the system, we need to consider the coefficient of performance (COP) of a Carnot heat pump.
The COP is given by the formula:
COP = T_cold / (T_hot - T_cold),
where T_cold is the indoor temperature (297 K) and T_hot is the outdoor temperature (308 K).
COP = 297 / (308 - 297) = 297 / 11 ≈ 27
The power required (P) can be calculated using the formula:
P = Q / COP, where Q is the heat transfer rate in kW.
First, convert the heat transfer rate to kW:
750 kJ/min = 12.5 kW.
P = 12.5 kW / 27 ≈ 0.463 kW
Learn more about the power at
https://brainly.com/question/16906267
#SPJ11
THIS IS PART OF YOUR PRAC APP:
While performing a diode check on a diode with a multimeter and the meters reads "0.00" while testing both sides of the diode, the diode is
A) function properly
B) Open Circuit
C) Short Circuit
If a multimeter reads "0.00" while performing a diode check on both sides of the diode, it indicates that the diode is a short circuit. This means that the diode has no resistance and is allowing current to flow in both directions, which is not the intended behavior of a diode.
A diode is a semiconductor device that allows current to flow in only one direction. It has two terminals, namely an anode and a cathode. The anode is the positive terminal, while the cathode is the negative terminal. When a voltage is applied across the diode in the forward direction, it conducts current, and when the voltage is applied in the reverse direction, it blocks the current flow.
A multimeter is an electronic instrument that is used to measure various electrical parameters like voltage, current, and resistance. It can also be used to check the polarity and continuity of a diode. To perform a diode check, the multimeter is set to the diode test mode, and the red probe is connected to the anode, while the black probe is connected to the cathode.
In conclusion, if the multimeter reads "0.00" while performing a diode check on both sides of the diode, it indicates that the diode is a short circuit. In this case, the diode needs to be replaced with a new one to ensure proper functioning of the circuit.
Learn more about multimeter here:
https://brainly.com/question/30809641
#SPJ11
Any items that are intended to remain permanently in place for the life of the structure. For example: internal walls, fixtures, and mechanical units is called a ?
The items that are intended to remain permanently in place for the life of a structure, such as internal walls, fixtures, and mechanical units, are typically referred to as "built-in" or "fixed" components.
These are elements that are integrated into the structure during construction and are not intended to be removed or replaced easily. Built-in or fixed components are designed to provide stability, functionality, and aesthetics to the structure, and they are typically planned and installed as part of the construction process. Examples of built-in components in a building may include walls, flooring, ceiling systems, lighting fixtures, HVAC (heating, ventilation, and air conditioning) units, plumbing fixtures, and electrical wiring systems, among others.
Learn more about built-in components here:
https://brainly.com/question/29308135
#SPJ11
Question 61
Marks: 1
The term "rem" does not take into consideration the biological effect of different kinds of radiation from the same dose in rads.
Choose one answer.
a. True
b. False
The statement is false, as the term "rem" does consider the biological effect of different kinds of radiation from the same dose in rads.
The term "rem" (Roentgen equivalent in man) does take into consideration the biological effect of different kinds of radiation from the same dose in rads. The rem is a unit of equivalent dose, which accounts for the varying levels of biological damage caused by different types of ionizing radiation. It is calculated by multiplying the absorbed dose in rads by a quality factor specific to the type of radiation in question, thus accounting for their differing biological effects.
To know more about Roentgen equivalent visit:
https://brainly.com/question/31560652
#SPJ11
An 02-series single-row deep-groove ball bearing with a 65-mm bore (see Tables 11-1 and 11-2 for specifications) is loaded with a 3-kN axial load and a 7-KN radial load. The outer ring rotates at 500 rev/min. (a) Determine the equivalent radial load that will be experienced by this particular bearing. (b) Determine whether this bearing should be expected to carry this load with a 95 percent reliability for 10kh Note:Text has tables for the bearing parameters, Table 11-1 & 11-2. Normally you are expected to extract these from bearing catalogues: SKF catalogue. Fe = XAVF, + Y Fa (11-9) Note: The rotational factor V is nottypically used by bearing suppliers in their prescribed selection process. For single-row deep-groove ball bearing V=1. 2 is suggested by the text. FORMULA SHEET Ln = an (9 p=3 for ball bearings and 10/3 for roller bearing
Corresponding to 500 rpm , 67.17 X 106 revolutions equal to 2239 hrs
So with 95% reliability, the bearing does not sustain the load for 10Kh
How to solveGiven
Axial load, Fa = 3KN
Radial load , Fr = 7KN
Speed = 500 Rpm
d = 65 mm
From SKF Catalogue (corresponding to 65mm dia deep groove ball bearing )
Dynamic load capacity, C = 42905 N
a) Equivalent radial load Fe = Xi V Fr +Yi Fa
From data book
Xi=0.56 , Yi = 1.3, V=1.2 (given)
Fe = 0.56X1.2X7 + 1.3X3 = 8.6 KN = 8600N
b) Rated life in million revolution, L90 = (C/Fe)3 = (42905/8600)3 = 124.17 = 124.17 X 106 revolutions
L95/L90 = (ln (1/R) / ln (1/R90))1/b = (6.85 (ln (1/0.95)(1/1.17) , R90 = 0.9, R = 0.95, b = 1.17 (constant)
L95 = 67.17 X 106 revolutions
Corresponding to 500 rpm , 67.17 X 106 revolutions equals to 2239 hrs
So with 95% reliability, the bearing does not sustain the load for 10Kh
Read more about load here:
https://brainly.com/question/13092760
#SPJ4
create a risk assesment plan that is tailored to address the following:
1. Identify hazards (eg site, trade/work, plant specific risks
2. Evaluate the risks (e.g. consequences, likelihood, impact, risk rating)
3. Control and mitigation measures
4. Action plant
The risk assessment plan is given below as follows:
The Risk Assessment PlanRisk Assessment Plan:
Identify Hazards:
Examining the geography of the site, one will be able to trace any impending physical dangers (e.g. unstable ground, unhidden electrical wiring). Additionally, reviewing the trade-work carried out and its particular risks by those conducting it (e.g. lofty movements, handling of power machines) as well as potential personal hazards related to the plant itself (e.g. inflammable elements, likelihood of explosions) should take place.
Evaluate the Risks:
To deduce the outliers of each uncovered threat (e.g. minor scratching, death) is necessary in order to measure the potency of occurrence (e.g. consistent, irregular, infrequent) for better understanding of the impact it can possibly cause (e.g. money due, legal effects, credibility damage). After taking these into consideration, assign a risk level based on them.
Control and Mitigation Measures:
Designing an agenda that seeks to eradicate or debilitate the detected hazards via putting into action engineering controls (e.g. support rails, anchorage vestments) as well as administrative prerequisites (e.g training agendas, warning signs), not forgetting to grant security equipment (PPE) wherever needed.
Action Plan:
A structured report must be written to make official knowledge of the assessment and control operations gone through. Furthermore, this document must be updated when fresh perils are noticed or at regular times, making sure that all personnel and contractors participating have knowledge about said hazards and safety methods applied along with being tutored on the correct use of said mechanisms.
Read more about risk assessment plan here:
https://brainly.com/question/28271580
#SPJ1
Question 2
Marks: 1
The addition of sodium bicarbonate is usually used to
Choose one answer.
a. raise the ambient water temperature
b. lower the ambient water temperature
c. raise the alkalinity
d. lower the pH
The addition of sodium bicarbonate is usually used to raise the alkalinity. So, the correct answer is option c.
Sodium bicarbonate, also known as baking soda, is commonly used in water treatment processes to increase the alkalinity. Alkalinity refers to the water's ability to neutralize acids and maintain stable pH levels. When sodium bicarbonate is added to water, it reacts with water to form carbonic acid, which then dissociates into bicarbonate ions. These ions increase the water's buffering capacity, meaning it can better resist changes in pH. This is important for maintaining a healthy aquatic environment, as fluctuations in pH can be harmful to aquatic organisms. Therefore, adding sodium bicarbonate helps to stabilize the water's pH by raising the alkalinity (option c).
To know more about the bicarbonate visit:
https://brainly.com/question/4513272
#SPJ11
In the event that a new set of stressing equipment is delivered to project,the equipment should contain___ for review prior to being used on-site
The new set of stressing equipment should contain documentation and instructions for review prior to being used on-site.
This documentation should include information on the proper use and maintenance of the equipment, as well as any safety guidelines and precautions that need to be taken.
It is important to thoroughly review this information before using the equipment to ensure that it is being used safely and effectively.
Taking the time to properly familiarize oneself with the equipment can also help prevent any potential equipment malfunctions or accidents.
Overall, it is crucial to prioritize safety and carefully follow all instructions when using new equipment on a project.
This ensures the equipment is safe, suitable, and properly calibrated for the project requirements.
Know more about documentation here:
https://brainly.com/question/1218796
#SPJ11
Which website interaction metric is best at detecting visitors that viewed only a single webpage on their visit?
Select one:
a. Pageviews Per Visit
b. Exit Percentage
c. Bounce Rate
d. Average Time On Site
Bounce Rate is the website interaction metric that is best at detecting visitors that viewed only a single webpage on their visit. The correct answer is (c).
Understanding Website MetricBounce rate is defined as the percentage of single-page visits, which means the percentage of visits in which a person left your website from the landing page without browsing any further. Therefore, if a visitor only views one page and then leaves the site, their visit will be counted as a bounce.
Pageviews per visit, exit percentage, and average time on site are not as good at detecting visitors that viewed only a single webpage on their visit.
Pageviews per visit and average time on site may be higher if a visitor views multiple pages, even if they only spend a short amount of time on each page.
Exit percentage measures the percentage of exits from a particular page, but a visitor can exit from any page on the site, not just the first page they viewed.
Learn more about site metric here:
https://brainly.com/question/1837503
#SPJ4
6) Two reservoirs are connected by a 380 ft long commercial steel pipe with a diameter of 2 ft. There is a square-edged entrance and exit and a threaded 90-degree elbow at the pump The 500 horse power pump supplies water from the lower reservoir to the upper reservoir. Determine the flow rate. 0 90 ft 7) Use the Hazen-Williams equation and the Manning's equation to solve problem 6 and compare your results
Hazen-Williams Equation:
The Hazen-Williams equation for head loss is given by:
[tex]hL = 10.67 * (L / C^1^.^8^5) * (Q^1^.^8^5 / d^4^.^8^7)[/tex]
How to determine the equationswhere:
hL = head loss (ft)
L = pipe length (380 ft)
C = Hazen-Williams roughness coefficient for commercial steel pipe (around 120)
Q = flow rate (ft³/s)
d = pipe diameter (2 ft)
[tex]hL_fittings = K * (v^2) / (2 * g)[/tex]
where:
v = flow velocity (ft/s)
g = gravitational acceleration (32.2 ft/s²)
The total head provided by the pump (Hp) is given by:
Hp = (P * 550) / (Q * 62.4)
Hp = hL_pipe + hL_fittings
Manning equation
[tex]Q = (1/n) * A * R^(^2^/^3^) * S^(^1^/^2^)[/tex]
where:
Q = flow rate (ft³/s)
n = Manning's roughness coefficient (for steel, n ≈ 0.012)
A = cross-sectional area of the pipe (ft²)
R = hydraulic radius (ft)
S = pipe slope (ft/ft)
Read more on manning equation here:https://brainly.com/question/31412408
#SPJ4