Answer:
Waves; wavelength; electromagnetic energy; ultraviolet light.
Explanation:
Sound are mechanical waves that are highly dependent on matter for their propagation and transmission.
Sound travels faster through solids than it does through either liquids or gases.
Light wave can be defined as an electromagnetic wave that do not require a medium of propagation for it to travel through a vacuum of space where no particles exist.
Hence, sound and light are both found as waves, with a variety of wavelength. The sun, a source of light waves specifically, releases a type of electromagnetic energy. It can be found as UVA or UVB types. These lights give off different levels of ultraviolet light, some of wich can be harmful.
Additionally, the ultraviolet spectrum is divided into three categories and these are; UVA, UVB and UVC.
Following are the response to the fill in the blanks:
Sound is a mechanical wave that is strongly dependent on material for development and conveyance. It moves faster through solids instead of through liquids or gases. The light wave is electromagnetic radiation that does not require a medium of propagation to pass through a void of space in which no particles exist. Both 'sound and light' can be found as waves having varying wavelengths. Light waves, in particular, emit a form of radiant waves, which is available in UVA and UVB varieties. The lights emit varying degrees of UV light, many of which are dangerous. In addition, the UV spectrum is classified into three categories: UVA, UVB, and UVC.Therefore, the answer is "Waves, wavelength, electromagnetic energy, ultraviolet light".
Learn more:
brainly.com/question/13695751
During sublimation and deposition, this state of matter is skipped:
A) Solid
B) gas
C) liquid
What is the momentum of a 4 kg object moving west at 4 m/s?*
O 12 kg*m/s (east)
O 1.33 kg*m/s (west)
O 16 kg*m/s (east)
16 kg*m/s (west)
Answer:
16kg*m/s west
Explanation:
P=M*V
Momentum= Mass time velocity, plug it into the formula,
M is 4 and V is 4, 4*4=16, and since the object is moving west its going to be west.
basically saying in simpler terms,
16=4*4
It takes 5000 J of work to lift a crate to a height of 5 m in 10 s of time.. Calculate the power.
Answer:
P = 500 W
Explanation:
Given that,
Work done to lift a crate to a height of 5 m is 5000 J
It takes 10 s
We need to find the power of the crate. We know that power is the rate of doing work. Mathematically, it can be given by :
[tex]P=\dfrac{W}{t}\\\\P=\dfrac{5000}{10}\\\\P=500\ W[/tex]
So, the power of the crate is equal to 500 W.
A force of 120 N is applied to the front of a sledge at an angle of 28.00 above the horizontal so as to pull the sledge a distance of 165 meters. How much work was done by the applied force?
Answer:
Workdone = 17482.36 Joules
Explanation:
Given the following data;
Force, F = 120 N
Angle, d = 28.0°
Distance, x = 165 m
To find the work done, we would use the following formula;
Workdone = FxCosd
Substituting into the formula, we have;
Workdone = 120*165*Cos(28)
Workdone = 19800 * 0.8830
Workdone = 17482.36 Joules
discuss impact of Newton's second law on roads
Answer:
The second law: When a force is applied to a car, the change in motion is proportional to the force divided by the mass of the car. This law is expressed by the famous equation F = ma, where F is a force, m is the mass of the car, and a is the acceleration, or change in motion, of the car
A vertical piston-cylinder device initially contains 0.1 m^3 of air at 400 K and 100 kPa. At this initial condition, the piston is resting on a stop. The piston-cylinder device is connected to a supply line with air at 400 K and a pressure of 500 kPa. The valve between the supply line and the piston-cylinder device is opened and is left open until the pressure in the piston-cylinder device reaches 500 kPa. The piston is observed to start moving when the pressure in the cylinder is 200 kPa and the piston continues to rise until it reaches a second stop. At the second stop, the piston-cylinder volume is 0.2 m^3 . The final temperature and pressure in the piston-cylinder device are 440 K and 500 kPa, respectively. Determine the heat transfer to or from the piston-cylinder device for the filling process Determine heat transfer (kJ) during the entire process.
Answer:
[tex]Q=-38.15kJ[/tex]
Explanation:
From the question we are told that
Piston-cylinder initial Volume of air [tex]v_1=0.1 m^3[/tex]
Piston-cylinder initial temperature [tex]T_1=400k[/tex]
Piston-cylinder initial pressure [tex]P_1= 100kpa[/tex]
Supply line temperature[tex]T_s=400k[/tex]
Supply line pressure [tex]P_s= 500kpa[/tex]
Valve final pressure [tex]P_v=500kpa[/tex]
Piston movement pressure [tex]P_m=200kpa[/tex]
Piston-cylinder final Volume of air[tex]v_2=0.2 m^3[/tex]
Piston-cylinder final temperature [tex]T_2=440k[/tex]
Piston-cylinder final pressure [tex]P_2= 500kpa[/tex]
Generally the equation for conservation of mass is mathematically given by
[tex]Q=m_2 \mu_2-m_1 \mu_1 +W-(m_2-m_1)h[/tex]
where
Initial moment
[tex]m_1=\frac{p_1 V_1}{RT_1}[/tex]
[tex]m_1=\frac{100*0.1}{0.287*400}[/tex]
[tex]m_1=8.7*10^-^2kg[/tex]
Final moment
[tex]m_2=\frac{p_2 V_2}{RT_2}[/tex]
[tex]m_1=\frac{500*0.3}{0.287*440}[/tex]
[tex]m_1=79*10^{-2}kg[/tex]
Work done by Piston movement pressure
[tex]W=Pd[/tex]
[tex]W=P(v_2-v_1)[/tex]
[tex]W=200(0.2-0.1))[/tex]
[tex]W=20000J[/tex]
Heat function
[tex]h=cT_1[/tex]
[tex]h=1.005(400)[/tex]
[tex]h=402[/tex]
Therefore
[tex]Q=(0.792*0.718(440)-0.0871*0.718(400)+20-(0.792-0.087)*402))[/tex]
[tex]Q=-38.15kJ[/tex]
It is given mathematically that the system lost or dissipated Heat of
[tex]Q=-38.15kJ[/tex]
What would happen to the two balls if one of them were kept positively charged and the charge on the other ball were slowly increased, making it more and more positive? View Available Hint(s) What would happen to the two balls if one of them were kept positively charged and the charge on the other ball were slowly increased, making it more and more positive? The balls would begin to move closer together. The balls would not move relative to each other. The balls would begin to move farther apart.
Answer:
the balls would move closer to each other
Explanation:
An elephant's legs have a reasonably uniform cross section from top to bottom, and they are quite long, pivoting high on the animal's body. When an elephant moves at a walk, it uses very little energy to bring its legs forward, simply allowing them to swing like pendulums. For fluid walking motion, this time should be half the time for a complete stride; as soon as the right leg finishes swinging forward, the elephant plants the right foot and begins swinging the left leg forward.
Answer:
is this the full question?
Explanation:
A 200kg bumper car moving 3 m/s collides head on with a 392kg bumper car moving 6m/s. After impact, the larger car continues traveling in the same direction with a velocity of 1.6 m/s . Determine the speed of the other car.
Answer:
the final speed of the smaller car is 5.624 m/s
Explanation:
Given;
mass of the small car, m₁ = 200 kg
initial velocity of the small car, u₁ = 3 m/s
mass of the larger car, m₂ = 392 kg
initial velocity of the larger car, u₂ = 6 m/s
final velocity of the larger car, v₂ = 1.6 m/s
let the direction of the larger car be positive
let the direction of the smaller car be negative
Apply the principle of conservation of linear momentum to determine the final speed of the smaller car.
m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂
200(-3) + 392(6) = 200v₁ + 392 x 1.6
-600 + 2352 = 200v₁ + 627.2
1752 = 200v₁ + 627.2
1752 - 627.2 = 200v₁
1124.8 = 200v₁
v₁ = 1124.8/200
v₁ = 5.624 m/s
Therefore, the final speed of the smaller car is 5.624 m/s
Given equal time periods, which statement about radioactive waste is correct?
A. Radioactive decay and nuclear fission always generate the same amount of waste.
B. Nuclear fusion generates less radioactive waste than radioactive decay does.
C. Nuclear fusion generates less radioactive waste than nuclear fission does.
D. Nuclear fission generates less radioactive waste than radioactive decay does.
What is a mechanical advantage?
Answer:
B
Explanation:
A Mechanical Advantage is when you use a piece of machinery to help you do work, and it is an easy advantage.
What is the amount of electrical potential is measured by?
A. ampere
B. watt
C. volts
Answer:
voltmeter (C. Volts)
Explanation:
The amount of electrical potential is measured by voltmeter. Electrical potential is the amount of work needed to move a unit electric charge from a reference point to the specific point in an electric field. The SI unit of electrical potential is Volt.
brainliest?
Answer:
Volts
Explanation:
Which describes the greenhouse effect? 1. Earth continues to get warmer over time because it is slowly moving closer to the sun. 2. Earth's atmosphere blocks the sun's ultraviolet light. 3. Pollution gets into the air, causing trees to not get enough oxygen. 4. Energy given off by earth is reflected off of earth's atmosphere back down to the surface.
Answer: The green house effect is best described by option 4 (Energy given off by earth is reflected off of earth's atmosphere back down to the surface).
Explanation:
The green house effect can be described as the energy given off by earth is reflected off of earth's atmosphere back down to the surface.
When energy from the sun passes through the atmosphere, some are absorbed which keeps the earth surface warm. While the rest is reflected back largely by cloud.
The energy which is emitted from the earth surface is called the infrared radiation. Some of the infrared radiation passess through the atmosphere but most is absorbed and re- emitted in all directions by the greenhouse gas molecules and clouds. This effect warms the earth surface and the lower atmosphere. Therefore this statement (Energy given off by earth is reflected off of earth's atmosphere back down to the surface) is correct about greenhouse effect.
For the greenhouse effect to occur, greenhouse gas molecules are mostly needed. Examples of these gases include:
--> Carbon dioxide (CO2),
--> Water vapor (H2O), and
--> Methane (CH4)
Over the years, the excessive human activities has lead to increase in the greenhouse gas molecules which has negatively affected the greenhouse effects.
An object moves from point A to B to C to D and finally to A
along the circle shown in the figure below.
a) Find the distance covered by the moving object.
b) Find the magnitude of the displacement of the object.
Answer:
a) The distance covered by the moving object is approximately 18.85 km
b) The magnitude of the displacement of the object is 0 (no displacement)
Explanation:
From the drawing, we have;
The sale of the drawing is 1 unit = 1 km
The radius of the circle in the drawing along which the object moves = 3 units
Therefore;
The radius of the circle along which the object moves, r = 1 km/unit × 3 units = 3 km
a) The distance covered by the object that moves from point A to B to C to D and finally to A is equal to the circumference of the circle
Therefore;
The distance covered by the moving object, d = 2·π·r
By pugging the value for r = 3 km
d = 2 × π × 3 km = 6·π km ≈ 18.85 km
The distance covered by the moving object, d ≈ 18.85 km
b) The displacement = The object's change in position
The initial position of the object = Point A
The final position of the object = Point A
Therefore, the displacement of the object, A = No displacement = 0 (No difference between the initial and final location of the object
A system releases 150 kJ of heat while 10 kJ of work is done on the system by
the surroundings. Calculate the change in internal energy (in kJ).
Answer:
160J OR 140J
Explanation:
Depends on teacher which formula your teacher uses.
U=Q+W OR U=Q-W
Method 1:
U=150+10J=160
U=150-10=140J
GIVING BRAINLIEST PLEASE HELP!!
-if you answer correctly ill give you brainliest which will give you 25pts-
Answer:
A, and D are the answers
Explanation:
The pulley. It is located where the bicycle chain and gears are. The chain is wrapped around the pulley which turns and causes the wheel to turn on its axle.
Geothermal energy is an alternative energy source, although it is not resourceful enough to replace more than a minor amount of the Earth’s energy needs. Why is this?
Answer: However, it is not resourceful enough to replace more than a minor amount of the Earth's energy needs. Drilling through the Earth to reach areas hot enough to create steam is possible, but very expensive and difficult. .
Explanation:
please, pretty please help me!
Answer:
umm
Explanation:
1223565 578633 =334675
Paper clips, nails, and scissors all act as which of the following?
electromagnets
ion magnets
temporary magnets
I think its ion magnets correct me if I'm wrong
Explain how energy that comes from the outside of the Earth system drives the flow of water on surface currents.
Answer:
The ocean and atmosphere are connected. They work together to move heat and fresh water across the globe. Wind-driven and ocean-current circulations move warm water toward the poles and colder water toward the equator. ... The majority of the thermal energy at the Earth's surface is stored in the ocean.
Explanation:
The ocean and atmosphere are connected. They work together to move heat and fresh water across the globe. Wind-driven and ocean-current circulations move warm water toward the poles and colder water toward the equator. ... The majority of the thermal energy at the Earth's surface is stored in the ocean.
A microphone is attached to a spring that is suspended from the ceiling, as the drawing indicates. Directly below on the floor is a stationary 375-Hz source of sound. The microphone vibrates up and down in simple harmonic motion with a period of 1.80 s. The difference between the maximum and minimum sound frequencies detected by the microphone is 2.75 Hz. Ignoring any reflections of sound in the room and using 343 m/s for the speed of sound, determine the amplitude (in m) of the simple harmonic motion.
Answer:
[tex]0.361\ \text{m}[/tex]
Explanation:
[tex]f_s[/tex] = Frequency of source = 375 Hz
[tex]\Delta f[/tex] = Difference between the maximum and minimum sound frequencies = 2.75 Hz
v = Speed of sound in air = 343 m/s
T = Time period = 1.8 s
[tex]v_m[/tex] = Maximum speed of the microphone
We have the relation
[tex]\Delta f=2f_s\dfrac{v_m}{v}\\\Rightarrow v_m=\dfrac{\Delta fv}{2f_s}\\\Rightarrow v_m=\dfrac{2.75\times 343}{2\times 375}\\\Rightarrow v_m=1.26\ \text{m/s}[/tex]
Amplitude is given by
[tex]A=\dfrac{v_mT}{2\pi}\\\Rightarrow A=\dfrac{1.26\times 1.8}{2\pi}\\\Rightarrow A=0.361\ \text{m}[/tex]
The amplitude of the simple harmonic motion is [tex]0.361\ \text{m}[/tex].
In regions of the cardiovascular system where there is steady laminar blood flow, the shear stress on cells lining the walls of the blood vessels is about 20 N / M2. If the shear strain is about 0.008, estimate the shear modulus for the affected cells.
Answer:
Shear Modulus = 2500 Pa = 2.5 KPa
Explanation:
The shear modulus is defined as the ratio between the shear stress and the shear strain. Hence, the shear modulus, in this case, can be calculated by the use of the following formula:
[tex]Shear\ Modulus = \frac{Shear\ Stress}{Shear\ Strain}\\[/tex]
we have,
shear stress = 20 N/m²
shear strain = 0.008
Therefore,
[tex]Shear\ Modulus = \frac{20\ N/m^2}{0.008}\\\\[/tex]
Shear Modulus = 2500 Pa = 2.5 KPa
Please help!!!!! This is for science and I don’t understand
Answer:
the correct one is B
Explanation:
In this exercise, indicate that crocodiles need a warm climate to survive.
The current climate in the western Colorado region where the temperature is 53ºF (11.7ºC) does not allow them to survive, therefore the appearance of fossil crocodiles and fossil subtropical plants and a clear indication that the climate in these regions was much more warm
when checking the answers the correct one is B
a bullet of mass 120g is fired horizontally into a fixed wooden block with a speed of 20m\s. The bullet is brought to rest in a wooden block in 0.1secs by a constant resistance
calculate the;(I) magnitude of the resistance
(ii) distance moved by the bullet in the wood
Answer:
1) F = 24 N
2) Distance = 1 m
Explanation:
We are given;
Mass; m = 120 g = 0.12 kg
Initial velocity; u = 20 m/s
Final velocity; v = 0 m/s since it came to rest.
Time; t = 0.1 s
We can calculate acceleration from Newton's first equation of motion;
a = (v - u)/t
a = (0 - 20)/0.1
a = -200 m/s²
1) magnitude of the resistance will be;
F = ma
F = 0.12 × (-200)
F = -24 N
Since, we are dealing with the magnitude, we will take the absolute value. Thus, F = 24 N
2) To find the distance moved by the bullet, we know that;
Distance = Average speed × time
Thus;
Distance = ((v + u)/2) × t
Distance = ((0 + 20)/2) × 0.1
Distance = 1 m
In this system, ___________________ energy from the sunlight causes the solar panel to create ___________________ energy which flows into the incandescent light bulb. In the light bulb, the ___________________ energy is transformed into two different types of energy: ___________________ energy and ___________________ energy.
Answer:
solar, heat,heat, light
A person starts running from 2 m/s to 6 m/s in 2 seconds.
Calculate the person's acceleration.
Var
Variables:
Solve:
F
Formula:
Answer:
2 m/s²
Explanation:
From the question given above, the following data were obtained:
Initial velocity (u) = 2 m/s
Final velocity (v) = 6 m/s
Time (t) = 2 s
Acceleration (a) =?
The acceleration of the person can be obtained as follow:
v = u + at
6 = 2 + (a×2)
6 = 2 + 2a
Collect like terms
6 – 2 = 2a
4 = 2a
Divide both side by 2
a = 4 / 2
a = 2 m/s²
Therefore, the acceleration of the person is 2 m/s²
PLEASE HELP ME :( I've tried solving it many times but my teacher keeps saying its wrong i really need help
Answer:
The charge on each end of the wire produces what we call an electric field. The electric field makes negative electrons want to travel towards the positive end of the wire (the end with not enough electrons).
the answer is d because it's going to positive.
is am alright? let me know.
particles q1, q2, and q3 are in a straight line. particles q1 = -5.00 x 10^-6 C, q2 = -5.00 x 10^-6 C. .5 between each what is the net force on q3
Answer:
1.12
Explanation:
Acellus
Answer: +1.12
Explanation:
This answer works for Acellus! :)
Does anyone know 19 and 20 ??
A type of organism that makes its own food. __________
The highest taxonomic classification of organisms.__________
The process through which organisms make new organisms of the same kind. _______
The taxonomic classification below domains._________
A type of organism that is made of more than one cell and is more specialized and eukaryotic.__________
A characteristic passed from female and male parents to their offspring.________
FILL IN THE BLANKS PLEASEEE WILL GIVE BRAINLIEST AND 50 POINTS
Answer:
1. An autotroph
2. Domain
3. Reproduction
4. Kingdom
5. Multicellular Organism
6. Genetic trait
Explanation: Took Bio honors 1 & 2