Stefan Lano needs displays that will show the musical instrument inventory in his chain of music stores that caters to musicians playing in world-class symphony orchestras in Basel, Switzerland; Buenos Aires, Argentina; and Philadelphia and New York in the United States. Design a form-fill interface for the inventory control of musical instruments in all four stores that could be used on a computer display screen. Assume that English will be the interface language.

Answer:

attached below is an example of  the form

Explanation:

This type of form-fill can be described/developed based on the requirements or information needed by the organization in order to perfectly fulfill an order  and also to retain customers by making the form very easy and interactive attached below is an example of such form fill  interface

Q.13 In order to produce maximum starting torque in a split-phase motor, how many degrees out of phase should the start- and run-winding currents be with each other?
Select one:
A. 180°
B. 0°
C. 120°
D. 90°

A transformer is to be used to provide power for a computer disk drive that needs 6.4 V (rms) instead of the 120 V (rms) from the wall outlet. The number of turns in the primary is 300, and it delivers 500 mA (the secondary current) at an output voltage of 6.4 V (rms). (a) Should the transformer have more turns in the secondary compared to the primary, or fewer turns

Technician A says that ultra-high-strength steels (UHSS) are generally defined as those steels with tensile strengths greater than 700 MPa.
Technician B says that advanced high-strength steels (AHSS) are generally defined as those steels with tensile strengths from 375 MPa up to 1700
Who is right?
O A only
OB only
O Both A and B
O Neither A norb
Table of Contents

A hydraulic jump is formed in a 4m wide outlet just downstream of a control gate, which is located at the upstream end of the outlet. The flow depth upstream of the gate is 20 m. Assume there are no losses in the flow through the gate. If the outlet discharge is 40 m3/s, determine (6 points)a. Flow depth downstream of the jump (y1)b. Energy losses in the jump (between y1 and y2).

A current value of 0.000005 A is equal to
Α. 50 μΑ. .
B. 5 mA.
C.5 HA.
D. 50 mA.

There are gauges available for checking panel flushness. TRUE OR FALSE?

A jet aircraft is in level flight at an altitude of 30,000 ft with an airspeed of 500 ft/s. The aircraft has a gross weight of 19,815 lb, a wingspan of 53.3 ft, and an average chord length of 6 ft. The Oswald efficiency factor is 0.81 and the zero-lift drag coefficient is equal to 0.02. The jet has two turbofan engines, each producing a maximum thrust of 3,650 lb at sea level.

Required:
a. Create a plot of the drag polar for this aircraft for CL from 0 to 5. Plot CL on the vertical axis, CD on the horizontal axis, and do not include negative CL values.
b. What is the total drag coefficient at the flight condition described above?
c. What is the required thrust for level flight at this altitude in lb?
d. If the pilot runs the engines at maximum thrust, what is the instantaneous rate of climb at this altitude and velocity?

Which of the following can cause a flopping sound at the front of the engine
A) drive belt too loose
B) timing chain too loose
C) drive belt too tight
D) timing chain too tight

write three ways of soil investigation of a site​

A baker deck decorates 42 cupcakes and 30 minute she decorated cupcakes at a constant rate how many cups cage the baker decorate pre-minute

7.13 An intersection approach has a saturation flow rate of 1500 veh/h, and vehicles arrive at the approach at the rate of 800 veh/h. The approach is controlled by a pretimed signal with a cycle length of 60 seconds and D/D/1 queuing holds. Local standards dictate that signals should be set such that all approach queues dissipate 10 seconds before the end of the effective green portion of the cycle. Assuming that approach capacity exceeds arrivals, determine the maximum length

Hot engine oil with heat capacity rate of 4440 w/k (product of mass flow rate and specific heat) and an inlet temperature of 150°c flows through a double pipe heat exchanger. the double pipe heat exchanger is constructed of a 1.5-m-long copper pipe (k = 250 w/m·k) with an inner tube of inside diameter 2 cm and outside tube diameter of 2.25 cm. the inner diameter of the outer tube of the double pipe heat exchanger is 6 cm. oil flowing at a rate of 2 kg/s through inner tube exits the heat exchanger at a temperature of 50°c. the cold fluid, i. e., water enters the heat exchanger at 20°c and exits at 70°c. assuming the fouling factor on the oil side and water side to be 0.00015 m2 ·k/w and 0.0001 m2 ·k/w, respectively, determine the overall heat transfer coefficient on inner and outer surface of the copper tube.

multimeter and the LCD is showing Hz. What's she measuring?
A. Resistance
B. Amplitude
C. Voltage
D. Frequency

Which part of a machine control unit interacts with the machine tools through electric signals?=]

A machine control unit is the electronic hardware that stores information and controls the machine tools. This unit contains a data processing unit that stores and manipulates data, and a ___________ that interacts with the machine tools through electrical signals.

Design a filter that has infinite DC gain, a gain of one from 1Hz to 100 Hz and filters (1storder) any signals above 100 Hz.a) Sketch the bode plotb) Sketch the s-planec) write the transfer function of the filterd) write the differential equatione) write out the unforced transient responsef) write out the frequency response

8. Which of these plastics is a themoplastic - melts or softens with heat.
Acrylic
Bakelite
Polyester resin
Melamine
Epoxy Resin

Could someone please help me, this is very urgent, I will pay an extra bonus if done correct.