The Handbook of Chemistry and Physics gives solubilities of the following compounds in grams per 100 mL water. Because these compounds are only slightly soluble, assume that the volume does not change on dissolution and calculate the solubility product for each.
(a) BaSeO4, 0.0118 g/100 mL
(b) Ba(BrO3)2 H20, 0.30 g/100 mL
(c) NH4MgAsO4-6H20, 0.038 g/100 mL
(d) La2(MoOs)3, 0.00179 g/100 mL

Answer:

PhCH2CH2COOH

Explanation:

This is a reaction of PhCH2CH2Br with KCN in the presence of H3O^+. The reaction first leads to the formation of PhCH2CH2CN.

We must recall that part of the properties of nitriles is that they can be converted to carboxylic acids in the presence of H3O^+. This is a common synthetic route for carboxylic acids.

Therefore, when the PhCH2CH2CN is now further reacted with H3O^+, the carboxylic acid PhCH2CH2COOH is formed as the major organic product of the reaction, hence the answer given above.

Answer:

Approximately 100 °C.

Explanation:

Hello,

In this case, since the entropy of vaporization is computed in terms of the heat of vaporization and the temperature as:

[tex]\Delta S_{vap}=\frac{\Delta H_{vap}}{T}[/tex]

We can solve for the temperature as follows:

[tex]T=\frac{\Delta H_{vap}}{\Delta S_{vap}}[/tex]

Thus, with the proper units, we obtain:

[tex]T=\frac{55500J/mol}{148J/(mol*K)} =375K\\\\T=102 \°C[/tex]

Hence, answer is approximately 100 °C.

Best regards.

Answer:

Explanation:

a ) Benzoic acid is formed . In any alkyl benzene derivative , potassium permanganate reacts to form carboxylic acid . It oxidises side chains to carboxylic acid .  

C₆H₅CH₃ + 0 = C₆H₅COOH + H₂O

O is provided by KMnO₄

b ) In this reaction isophthalic acid is formed .

C₆H₄(CH₃)₂ +O = C₆H₄(COOH)₂

c)

4-Propyl-3-t-butyltoluene

In this oxidation , three side chains of ring  are 1 ) 1-methyl 2 ) 3- butyl 3 ) 4 propyl .

The methyl and 4 - propyl groups are oxidised to di- carboxylic acid and 3 butyl group remains intact ( unoxidised )

Answer:

6

Explanation:

Alkanes undergo substitution reaction so the number of replacement reaction hydrogen is 6

Answer:

Graphite> sodium chloride> solid ammonia

Explanation:

Melting points of solids has a lot to do with the nature of intermolecular forces in the solid. A substance melts when the intermolecular forces holding the crystal lattice has been overcome such that that the crystal structure of the solid just collapses.

Graphite consists of covalently bonded layers of carbon atom which form a giant lattice. The melting point of graphite is very high because of the fact that the strong covalent bonds that hold the carbon atoms together in the layers require a lot of heat energy to break. Grapoghite melts at about 3600°C

Sodium chloride is an ionic compound that melts at about 801°C. The lattice is composed of alternate sodium and chloride ions.

Solid ammonia is held together by much weaker intermolecular interaction hence it has a melting point of about −77.73 °C.

Answer:

too low

Explanation:

If our aim is to recover the naphthalene and measure its mass after separation, then we must not allow any vapour to escape.

Naphthalene is a sublime substance, it can be separated by sublimation. It changes directly from solid to gas. This vapour must be kept securely so that none of it escapes. If part of the naphthalene vapour happens to escape accidentally, then the measured mass of naphthalene will be too low compared to the mass of naphthalene originally present in the mixture.

Answer:

b. Binary compounds of carbon and hydrogen

Explanation:

Before proceeding, Hydrocarbons refers to organic chemical compounds composed exclusively of hydrogen and carbon atoms. This means the only elements present in an hydrocarbon are;

- Carbon

- Hydrogen

Looking through the options;

- Option A: This is wrong because the hydroxyl group contains oxygen and hydrocarbons contain only hydrogen and carbon.

- option B: This is correct. Binary compounds refers to compounds with just two elements.

- option C: This is wrong because water contains oxygen and hydrocarbons contain only hydrogen and carbon.

- option D: Carbon atoms can contain other elements so this option is wrong.

- option E: This also wrong because we had already gotten the correct option.

Answer:

0.373 M

Explanation:

The balanced equation for the reaction is given below:

HC2H3O2 + NaOH —> NaC2H3O2 + H2O

From the balanced equation above, the following were obtained:

Mole ratio of the acid, HC2H3O2 (nA) = 1

Mole ratio of the base, NaOH (nB) = 1

Next, we shall write out the data obtained from the question. This include:

Volume of base, NaOH (Vb) = 32.17 mL

Molarity of base, NaOH (Mb) = 0.116 M

Volume of acid, HC2H3O2 (Va) = 10 mL

Molarity of acid, HC2H3O2 (Ma) =..?

The molarity of the acid solution can be obtained as follow:

MaVa/MbVb = nA/nB

Ma x 10 / 0.116 x 32.17 = 1

Cross multiply

Ma x 10 = 0.116 x 32.17

Divide both side by 10

Ma = (0.116 x 32.17) /10

Ma = 0.373 M

Therefore, the concentration of the acetic acid is 0.373 M.

Answer:

1. REDOX

2. None of the above

3. Precipitation

4. Preicipitation

5. Acid base neutralization

Explanation:

Reactions where a solid is formed, are named as precipitation. This solid is called precipitated.

Option 4 and 3.

3) CaO (s) + CO₂ (g) →  CaCO₃(s)

4) KOH (aq)  + AgCl (aq)  →  KCl (aq)  + AgOH(s)

Reactions where water is produced, and you have an acid and a base as reactants, are named as neutralization. You called them acid-base because, the products.

5) Ba(OH)₂ (aq)  +  2HNO₂(aq)  →  Ba(NO₂)₂ (aq) + 2H₂O(l)

Redox, are the reactions where one of the reactans can be oxidized and reduced, when a mole of electrons is released, or gained.

1) Ba(ClO₃)₂ (s)  → BaCl₂ (s) +  3O₂(g)

Oxygen from the chlorate is oxidized (increases the oxidation state from -2 to 0) and the chlorine is reduced (decreases the oxidation state from +5 to -1).

2.  2NaCl(aq)  +  K₂S(aq)  Na₂S (aq)  + 2KCl (aq)

None of the above

Answer:

495nm

Explanation:

The energy of a photon could be obtained by using:

E = hc / λ

Where E is energy of a photon, h is Planck's constant (6.626x10⁻³⁴Js), c is speed of the light (3x10⁸ms⁻¹) and λ is wavelength.

The energy to break 1 mole of Cl-Cl bonds is 242kJ = 242000J. The energy yo break a single bond is:

242000J/mol ₓ (1mol / 6.022x10²³bonds) = 4.0186x10⁻¹⁹J/bond.

Replacing in the equation:

E = hc / λ

4.0186x10⁻¹⁹J = 3x10⁸ms⁻¹ₓ6.626x10⁻³⁴Js / λ

λ = 4.946x10⁻⁷m

Is maximum wavelength  of light that could break a Cl-Cl bond.

Usually, wavelength is given in nm (1x10⁻⁹m / 1nm). The wavelength in nm is:

4.946x10⁻⁷m ₓ (1nm / 1x10⁻⁹m) =

Answer:

The correct option is d

Explanation:

Nuclide is synonymous with groups of electrons or protons, that is, a nuclide is the grouping of nucleons.

Answer:

Coordinate or r = (7,9).

Explanation:

Data obtained from the question include the following:

Mid point = (8,7)

Coordinate of S = (9,5)

Coordinate of r =...?

We shall determine the coordinate of r as follow:

Let the coordinate of r be (x2, y2)

Mid point = (x1 + x2)/2 , (y1 + y2)/2

Mid point = (8,7)

Coordinate of S = (9,5)

x1 = 9

y1 = 5

x2 =?

y2 =?

The value of x2 can be obtained as follow:

8 = (x1 + x2)/2

8 = (9 + x2)/2

Cross multiply

9 + x2 = 2 × 8

9 + x2 = 16

Collect like terms

x2 = 16 – 9

x2 = 7

The value of y2 can be obtained as follow:

5 = (y1 + y2)/2

7 = (5 + y2)/2

Cross multiply

5 + y2 = 2 × 7

5 + y2 = 14

Collect like terms

y2 = 14 – 5

y2 = 9

Coordinate of r = (x2, y2)

Coordinate or r = (7,9)

Answer:

(1) Before the addition of any HBr, the pH is 12.02

(2) After adding 12.0 mL of HBr, the pH is 10.86

(3) At the titration midpoint, the pH is 10.73

(4) At the equivalence point, the pH is 5.79

(5) After adding 45.1 mL of HBr, the pH is 1.18

Explanation:

First of all, we have a weak base:

(CH₃)₂NH  + H₂O  ⇄  (CH₃)₂NH₂⁺  +  OH⁻            Kb = 5.4×10⁻⁴

0.289 - x                             x                x

Kb = x² / 0.289-x

Kb . 0.289 - Kbx - x²

1.56×10⁻⁴ - 5.4×10⁻⁴x - x²

After the quadratic equation is solved x = 0.01222 → [OH⁻]

- log  [OH⁻] = pOH → 1.91

pH = 12.02   (14 - pOH)

We determine the mmoles of H⁺, we add:

0.286 M . 12 mL = 3.432 mmol

We determine the mmoles of base⁻, we have

27.9 mL . 0.289 M = 8.0631 mmol

When the base, react to the protons, we have the protonated base plus water (neutralization reaction)

(CH₃)₂NH     +      H₃O⁺        ⇄  (CH₃)₂NH₂⁺  +  H₂O

8.0631 mm       3.432 mm                 -

4.6311 mm                                  3.432 mm

We substract to the dimethylamine mmoles, the protons which are the same amount of protonated base.

[(CH₃)₂NH] → 4.6311 mm / Total volume (27.9 mL + 12 mL) = 0.116 M

[(CH₃)₂NH₂⁺] → 3.432 mm / 39.9 mL = 0.0860 M

We have just made a buffer.

pH = pKa + log (CH₃)₂NH  / (CH₃)₂NH₂⁺

pH = 10.73 + log (0.116/0.0860) = 10.86

mmoles of base = mmoles of acid

Let's find out the volume

0.289 M . 27.9 mL = 0.286 M . volume

volume in Eq. point = 28.2 mL

(CH₃)₂NH     +      H₃O⁺        ⇄  (CH₃)₂NH₂⁺  +  H₂O

8.0631 mm       8.0631mm               -

                                                8.0631 mm

We do not have base and protons, we only have the conjugate acid

We calculate the new concentration:

mmoles of conjugated acid / Total volume (initial + eq. point)

[(CH₃)₂NH₂⁺] = 8.0631 mm /(27.9 mL + 28.2 mL)  = 0.144 M

(CH₃)₂NH₂⁺   +  H₂O   ⇄   (CH₃)₂NH  +  H₃O⁻       Ka = 1.85×10⁻¹¹

 0.144 - x                                  x               x

[H₃O⁺] = √ (Ka . 0.144) →  1.63×10⁻⁶ M  

pH = - log [H₃O⁺] = 5.79

This is the point where we add, the half of acid. (14.1 mL)

This is still a buffer area.

mmoles of H₃O⁺ = 4.0326 mmol (0.286M . 14.1mL)

mmoles of base = 8.0631 mmol - 4.0326 mmol

[(CH₃)₂NH] = 4.0305 mm / (27.9 mL + 14.1 mL) = 0.096 M

[(CH₃)₂NH₂⁺] = 4.0326 mm (27.9 mL + 14.1 mL) = 0.096 M

pH = pKa + log (0.096M / 0.096 M)

pH = 10.73 + log 1 =  10.73

Both concentrations are the same, so pH = pKa. This is the  maximum buffering capacity.

mmoles of acid = 45.1 mL . 0.286 M = 12.8986 mmol

mmoles of base = 8.0631 mmoles

This is an excess of H⁺, so, the new [H⁺] = 12.8986 - 8.0631 / Total vol.

(CH₃)₂NH     +      H₃O⁺        ⇄  (CH₃)₂NH₂⁺  +  H₂O

8.0631 mm     12.8986 mm             -

       -               4.8355 mm                        

[H₃O⁺] = 4.8355 mm / (27.9 ml + 45.1 ml)

[H₃O⁺] = 4.8355 mm / 73 mL → 0.0662 M

- log [H₃O⁺] = pH

- log 0.0662 = 1.18 → pH

Answer:

Molar mass of the gas is 0.0961 g/mol

Explanation:

The effusion rate of an unknown gas = 11.1 min

rate of [tex]H_{2}[/tex] effusion = 2.42 min

molar mass of hydrogen = 1 x 2 = 2 g/m

molar mas of unknown gas = ?

From Graham's law of diffusion and effusion, the rate of effusion and diffusion is inversely proportional to the square root of its molar mass.

from

[tex]\frac{R_{g} }{R_{h} }[/tex] = [tex]\sqrt{\frac{M_{h} }{M_{g} } }[/tex]

where

[tex]R_{h}[/tex] = rate of effusion of hydrogen gas

[tex]R_{g}[/tex] = rate of effusion of unknown gas

[tex]M_{h}[/tex] = molar mass of H2 gas

[tex]M_{g}[/tex] = molar mass of unknown gas

substituting values, we have

[tex]\frac{11.1 }{2.42 }[/tex] = [tex]\sqrt{\frac{2 }{M_{g} } }[/tex]

4.587 = [tex]\sqrt{\frac{2 }{M_{g} } }[/tex]

[tex]\sqrt{M_{g} }[/tex] = [tex]\sqrt{2}[/tex]/4.587

[tex]\sqrt{M_{g} }[/tex] = 0.31

[tex]M_{g}[/tex] = [tex]0.31^{2}[/tex] = 0.0961 g/mol

The molar mass of the unknown gas will be "0.0961 g/mol".

Given:

Effusion rate of unknown gas,

Effusion rate of [tex]H_2[/tex],

Molar mass of hydrogen,

              [tex]= 2 \ g/m[/tex]

According to the Graham's law, we get

→    [tex]\frac{R_g}{R_h} = \sqrt{\frac{M_h}{M_g} }[/tex]

By substituting the values, we get

→   [tex]\frac{11.1}{2.42} = \sqrt{\frac{2}{M_g} }[/tex]

→ [tex]4.587=\sqrt{\frac{2}{M_g} }[/tex]

→ [tex]\sqrt{M_g} = \sqrt{\frac{2}{4.587} }[/tex]

   [tex]\sqrt{M_g} = 0.31[/tex]

       [tex]M_g = 0.0961 \ g/mol[/tex]

Thus the above solution is right.          

Learn more:

https://brainly.com/question/6019799

Radiologists are medical doctors that treat injuries using medical imaging (radiology)

Answer:

a person who uses X-rays or other high-energy radiation, especially a doctor specializing in radiology.

Explanation:

Answer:

The number of oxide ions as the nearest neighbors of  [tex]{\rm{M}}{{\rm{g}}^{{\rm{2 + }}}}[/tex] ions are known to be as six

Explanation:

The regularity of a crystal structure leads to the idea of space lattice.In order to explain this concept, let us consider a crystal of NaCl, It consists of a perfectly regular arrangement of sodium ions and chlorine ions.

If we represent the position of each Na+ in the crystal by a point marked x the result will be a regular three dimensional network of points. This will be the space lattice of Na+ in the crystal NaCl. The symmetry of the combined lattice determined the symmetry of the crystal as a whole.

The space lattice of a crystal may be considered as built up of a three dimensional basic pattern  called unit cell. The unit cell is a repeat unit which generates the whole pattern in three dimensions of the unit cell.

In Solid MgO , the crystal structure which is used to predict the properties of the material, have the same structure as that of NaCl.

The obtain the structure of a face centered cubic FCC unit cell where the ions occupy the corner of the cube and the center of each face of the cube.

The number of oxide ions as the nearest neighbors of  [tex]{\rm{M}}{{\rm{g}}^{{\rm{2 + }}}}[/tex] ions are known to be as six. As a result of that , the coordination number of [tex]{\rm{M}}{{\rm{g}}^{{\rm{2 + }}}}[/tex] ions is six.

Answer:

It will take 6486.92 minutes  for [H2O2] to fall from 0.95 M to 0.33 M

Explanation:

The order of reaction is defined as the sum of the powers of the concentration terms in the equation. Order of a reaction is given by the number of atoms or molecule whose concentration change during the reaction and determine the rate of reaction.

In first order reaction;

[tex]In \dfrac{a}{a_o-x}= k_1 t[/tex]

where;

a = concentration at time t

[tex]a_o[/tex] = initial concentration

and k = constant.

[tex]In (\dfrac{0.33}{0.95})= -1.63 \times 10^{-4} \times t[/tex]

[tex]-1.05736933 = -1.63 \times 10^{-4} \times t[/tex]

[tex]t = \dfrac{-1.05736933}{ -1.63 \times 10^{-4} }[/tex]

t = 6486.92 minutes

Answer:

Osmolarity of solution of KCI = 0.40 osmol

Explanation:

Given:

KCL ⇒ K⁺ + Cl⁻

Find:

Osmolarity of solution of KCI

When M = 0.20 M

Computation:

1 mole of KCL = 2 osmol

1 M of KCl = 2 Osmolarity

So,

Osmolarity of solution of KCI = 2 × 0.20

Osmolarity of solution of KCI = 0.40 osmol

Answer:

a. increase

Explanation:

Catalysis is the process of increasing the rate of a chemical reaction by adding a substance known as a catalyst, which is not consumed in the catalyzed reaction.

By default, catalysts exists to speed up the rate of reactions. Increasing the amount of catalysts means that there would be an increase in the rate of reaction. The correct option is A.

Answer:

Explanation:

Mn( NO₃ )₂ + 2Na OH = Mn( OH)₂ (s) ↓ +  2Na NO₃

Converting into ions

Mn⁺ + 2 NO₃⁻ + 2 Na⁺ + 2 OH⁻ = Mn( OH)₂ + 2 Na⁻ + 2 NO₃⁻

Cancelling out common terms

Mn⁺ + 2 OH⁻ = Mn( OH)₂

this is net ionic equation required.

Answer:

Option A

Explanation:

Silicon (Obtained from Sand (SiO2)) is the element that is primarily used in appliances to make electronic chips.

Answer:

A. Silicon (Si)

Explanation:

Silicon (Si) is primarily used as a semiconductor material to make electronic chips.

Answer:

37%

Explanation:

From the question, the equation goes does.

C2H6+ (1-x)+a(O2+3.76N2)=bC02 + cH2O + axO2 + 3.76dN2.

Mair=Mair/Rin

( MN)O2 + (MN)N2÷ (MN)O2 + (MN)N2 +(MN)C2H6.

33 . 3.25(1-x) + 28 × 13.16(1-x) ÷ 33 × 3.25(1-x) + 28 × 13.16(1-x). + 30.1

= 176/176+8

X= 0.37

0.37 × 100

X= 37%

Answer:

An alkyl halide can undergo SN2 reaction with an amine

Explanation:

The displacement of a bromine atom by an an amine (step 2---> 3) in the reaction sequence is an example of an SN2 reaction in which the amine is the nucleophile.

The nitrogen atom of the amine which bears a lone pair of electrons functions as the nucleophile and attacks the electrophilic carbon atom of the alkyl halide displacing the bromide and creating a new Carbon-Nitrogen bond. An ammonium intermediate is immediately formed and the reaction is completed by the abstraction of a hydrogen by a base (such as excess amine present in the system).

This reaction is slower with t-BuNH2 because of steric hindrance and steric crowding in the transition state. SN2 reactions are faster with methylamine where the alkyl carbon is easily accessible.

The detailed mechanism of this reaction has been attached to this answer.

A heterogeneous mixture​

Answer:

A

Explanation:

The number of protons indicates the element so we know it's potassium. To get the number of neutrons you subtract the number of protons (19) from the mass number which for potassium is 39.

39-19=20 neutrons

Because you have 18 neutrons then yours would be an isotope.

Answer: A. Isotope of potassium(K)

Explanation: Founders Educere answer.

Answer:

4NH₃(g)  + 5O₂(g)  →  4NO(g)  +  6H₂O

2NO(g) + O₂(g) → 2 NO₂

Explanation:

First of all, we need to consider the reaction for production of ammonia. In this reaction we have as reactants, nitrogen and hydroge.

3H₂ (g) +  N₂(g)  →  2NH₃ (g)

Afterwards, ammonia reacts to oxygen, to produce NO and H₂O

The equation for the process will be:

4NH₃(g)  + 5O₂(g)  →  4NO(g)  +  6H₂O

Then, we take the nitric oxide to make it react, to produce NO₂, in order to produce nitric acid, for the final reaction:

2NO(g) + O₂(g) → 2 NO₂

3NO₂(g) + H₂O(g) → 2 HNO₃ (g) + NO(g)

Answer:

The Nuclear magnetic resonance is the process this technique does not use radiation.

The  ms is an sensitive technology can be a massive number and small sample of the blood.

Explanation:

The Nuclear magnetic resonance we look at the both side of that coin.

The technique provides that fatty acid composition and various including amino acids.

These are contain the complementary these biomarkers, that are suitable for all kinds of studies. there are many types of research:-

(1) A powerful tool metabolic (2) A versatile tool research (3) Quick analysis (4) Low cost analysis.

The MS is an extremely sensitive technology using a very small number of the blood.

(1) Powerful techniques (2) Highly method (3) Large number of metabolites (4)Small sample volume

MS can be fine mapping metabolic pathways to sign analytical strategy.

Answer:

0.3 mol

Explanation:

Assuming HCl is in excess and Zn is the limiting reagent,

from the balanced equation, we can see the mole ratio of Zn:H2 = 1:1,

which means, each mole of zinc reacted gives 1 mole of H2.

So, if 0.30 mol Zn is added, the no. of moles of H2 produced will also be 0.3 mol, since the ratio is 1:1.