Answer:
R₈₀ = 146.43 Ω
Explanation:
The resistance of a resistor depends upon many factors. One of the main factors of the change in resistance of a resistor is the change in temperature. The formula for the resistance at a temperature other than 20°C is given as follows:
R₈₀ = R₀(1 + αΔT)
where,
R₈₀ = Resistance of wire at 80°C = ?
R₀ = Resistance of wire at 20° C = 104 Ω
α = Temperature coefficient of resistance for copper = 0.0068 °C⁻¹
ΔT = T₂ - T₁ = 80°C - 20°C = 60°C
Therefore,
R₈₀ = (104 Ω)[1 + (0.0068°C⁻¹)(60°C)]
R₈₀ = 146.43 Ω
A commercial aircraft is flying westbound east of the Sierra Nevada Mountains in California. The pilot observes billow clouds near the same altitude as the aircraft to the south, and immediately turns on the "fasten seat belt" sign. Explain why the aircraft experiences an abrupt loss of 500 meters of altitude a short time later.
Answer:
Billow clouds provide a visible signal to aviation interests of potentially dangerous turbulent sky since they indicate instability in air currents.
Explanation:
Billow clouds are created in regions that are not stable in a meteorological sense. They are frequently present in places with air flows, and have marked vertical shear and weak thermal separation and inversion (colder air stays on top of warmer air). Billow clouds are formed when two air currents of varying speeds meet in the atmosphere. They create a stunning sight that looks like rolling ocean waves. Billow clouds have a very short life span of minutes but they provide a visible signal to aviation interests of potentially dangerous turbulent sky since they indicate instability in air currents, which although may not affect us on the ground but is a concern to aircraft pilots. The turbulence due to the Billow wave is the only logical explanation for the loss of 500 m in altitude of the plane.
In a single-slit diffraction experiment, the width of the slit through which light passes is reduced. What happens to the width of the central bright fringe
Answer:
It becomes wider
Explanation:
Because The bigger the object the wave interacts with, the more spread there is in the interference pattern. Decreasing the size of the opening increases the spread in the pattern.
A segment of wire of total length 3.0 m carries a 15-A current and is formed into a semicircle. Determine the magnitude of the magnetic field at the center of the circle along which the wire is placed.
Answer:
4.9x10^-6T
Explanation:
See attached file
a uniform rod of 30cm is pivoted at its center.a 40N weight is hung 5cm from left.from where 50N weight be hung to maintain equilibrium?
Answer:
The 50N weight be hung at 23 cm to maintain equilibrium
Explanation:
Given;
length of the uniform rod = 30 cm
center of the uniform rod = 15 cm
weight of 40N is hung at 5 cm mark
weight of 50 N will be hung at ?
0------5cm-----------------15cm-------------P---------30cm
↓ 10cm Δ xcm ↓
40N 50N
Take moment about the pivot point and apply the principle of moment
50N (x cm) = 40N (10 cm)
x = (400) / 50
x = 8cm
P = x cm + 15 cm
P = 8 cm + 15 cm
P = 23 cm
Therefore, the 50N weight be hung at 23 cm to maintain equilibrium
An electron initially at rest is accelerated over a distance of 0.210 m in 33.3 ns. Assuming its acceleration is constant, what voltage was used to accelerate it
Answer:
V = 451.47 volts
Explanation:
Given that,
Distance, d = 0.21 m
Initial speed, u = 0
Time, t = 33.3 ns
Let v is the final velocity. Using second equation of motion as :
[tex]d=ut+\dfrac{1}{2}at^2[/tex]
a is acceleration, [tex]a=\dfrac{v-u}{t}[/tex] and u = 0
So,
[tex]d=\dfrac{1}{2}(v-u)t[/tex]
[tex]v=\dfrac{2d}{t}\\\\v=\dfrac{2\times 0.21}{33.3\times 10^{-9}}\\\\v=1.26\times 10^7\ m/s[/tex]
Now applying the conservation of energy i.e.
[tex]\dfrac{1}{2}mv^2=qV[/tex]
V is voltage
[tex]V=\dfrac{mv^2}{2q}\\\\V=\dfrac{9.1\times 10^{-31}\times (1.26\times 10^7)^2}{2\times 1.6\times 10^{-19}}\\\\V=451.47\ V[/tex]
So, the voltage is 451.47 V.
Two point charges of +2.0 μC and -6.0 μC are located on the x-axis at x = -1.0 cm and x 12) = +2.0 cm respectively. Where should a third charge of +3.0-μC be placed on the +x-axis so that the potential at the origin is equal to zero?
Answer:
x = 0.006 m
Explanation:
The potential at one point is given by
V = k ∑ [tex]q_{i} / r_{i}[/tex]
remember that the potential is to scale, let's apply to our case
V = k (q₁ / x₁ + q₂ / x₂ + q₃ / x)
in this case they indicate that the potential is zero
0 = k (2 10⁻⁶ / (- 1 10⁻²) + (-6 10⁻⁶) / 2 10⁻² + 3 10⁻⁶ / x)
3 / x = + 2 / 10⁻² + 3 / 10⁻²
3 / x = 500
x = 3/500
x = 0.006 m
What explains why a prism separates white light into a light spectrum?
A. The white light, on encountering the prism, undergoes both reflection and refraction; some of the reflected rays re-enter the prism merging with refracted rays changing their frequencies.
B. The white light, on entering a prism, undergoes several internal reflections, forming different colors.
C. The different colors that make up a white light have different refractive indexes in glass.
D. The different colors that make up a white light are wavelengths that are invisible to the human eye until they pass through the prism.
E. The different rays of white light interfere in the prism, forming various colors.
Answer:
I think the answer probably be B
What explains why a prism separates white light into a light spectrum ?
C. The different colors that make up a white light have different refractive indexes in glass.
✔ Indeed, depending on the radiation (and therefore colors), which each have different wavelengths, the refraction index varies: the larger the wavelength (red) the less the reflection index is important and vice versa (purple).
✔ That's why purple is more deflected so is lower than red radiation.
Suppose your 50.0 mm-focal length camera lens is 51.0 mm away from the film in the camera. (a) How far away is an object that is in focus
Answer:
2.55m
Explanation:
Using 1/do+1/di= 1/f
di= (1/f-1/do)^-1
( 1/0.0500-1/0.0510)^-1
= 2.55m
A long solenoid (1500 turns/m) carries a current of 20 mA and has an inside diameter of 4.0 cm. A long wire carries a current of 2.0 A along the axis of the solenoid. What is the magnitude of the magnetic field at a point that is inside the solenoid and 1.0 cm from the wire
Answer:
The magnitude of the magnetic field is 55μT
Explanation:
Given;
number of turns of the solenoid per length, n = N/L = 1500 turns/m
current in the solenoid, I = 20 mA = 20 x 10⁻³ A
diameter of the solenoid, d = 4 cm = 0.04 m
The magnetic field at a point that is inside the solenoid;
B₁ = μ₀nI
Where;
μ₀ is permeability of free space = 4π x 10⁻⁷ m/A
B₁ = 4π x 10⁻⁷ x 1500 x 20 x 10⁻³
B₁ = 3.77 x 10⁻⁵ T
Given;
current in the wire, I = 2 A
distance of magnetic field from the wire, r = 1 cm = 0.01 m
The magnetic field at 1.0 cm from the wire;
[tex]B_2 = \frac{\mu_0I}{2\pi r} \\\\B_2 = \frac{4\pi*10^{-7}*2}{2\pi *0.01}\\\\B_2 = 4 *10^{-5} \ T[/tex]
The magnitude of the magnetic field;
[tex]B = \sqrt{B_1^2 +B_2^2} \\\\B = \sqrt{(3.77*10^{-5})^2 + (4*10^{-5})^2} \\\\B = 5.5 *10^{-5} \ T\\\\B = 55 \mu T[/tex]
Therefore, the magnitude of the magnetic field is 55μT
The magnitude of the magnetic field at a point that is inside the solenoid and 1.0 cm from the wire is [tex]5.5 \times 10^{-5}T[/tex]
Given the following parameters from the question
Number of turns of the solenoid per length, n = N/L = 1500 turns/m current in the solenoid, I = 20 mA = 20 x 10⁻³ A Diameter of the solenoid, d = 4 cm = 0.04 mThe magnetic field at a point that is inside the solenoid is expressed according to the formula;
B₁ = μ₀nIWhere;
μ₀ is the permeability of free space = 4π x 10⁻⁷ m/A
B₁ = 4π x 10⁻⁷ x 1500 x 20 x 10⁻³
B₁ = 3.77 x 10⁻⁵ T
Next is to get the magnetic field strength in the second wire.
Current in the wire, I = 2 A Distance of magnetic field from the wire, r = 1 cm = 0.01 mThe magnetic field at 1.0 cm from the wireSubstitute into the formula:
[tex]B_2=\dfrac{\mu_0 I}{2 \pi r} \\B_2=\frac{4\pi \times 10^{-7}\times 2}{2 \times 3.14\times 0.01} \\B_2 =4.0 \times 10^{-5}T[/tex]
Get the resultant magnetic field:
[tex]B = \sqrt{(0.00003771)^2+(0.00004)^2} \\B =5.5 \times 10^{-7}T[/tex]
Therefore the magnitude of the magnetic field at a point that is inside the solenoid and 1.0 cm from the wire is [tex]5.5 \times 10^{-5}T[/tex]
Learn more on the magnetic field here: https://brainly.com/question/15277459
What are the approximate dimensions of the smallest object on Earth that astronauts can resolve by eye when they are orbiting 275 km above the Earth
Answer:
s_400 = 16.5 m , s_700 = 29.4 m
Explanation:
The limit of the human eye's solution is determined by the diffraction limit that is given by the expression
θ = 1.22 λ / D
where you lick the wavelength and D the mediator of the circular aperture.
In our case, the dilated pupil has a diameter of approximately 8 mm = 8 10-3 m and the eye responds to a wavelength between 400 nm and 700 nm.
by introducing these values into the formula
λ = 400 nm θ = 1.22 400 10⁻⁹ / 8 10⁻³ = 6 10⁻⁵ rad
λ = 700 nm θ = 1.22 700 10⁻⁹ / 8 10⁻³-3 = 1.07 10⁻⁴ rad
Now we can use the definition radians
θ= s / R
where s is the supported arc and R is the radius. Let's find the sarcos for each case
λ = 400 nm s_400 = θ R
S_400 = 6 10⁻⁵ 275 10³
s_400 = 16.5 m
λ = 700 nm s_ 700 = 1.07 10⁻⁴ 275 10³
s_700 = 29.4 m
An RC circuit is connected across an ideal DC voltage source through an open switch. The switch is closed at time t = 0 s. Which of the following statements regarding the circuit are correct?
a) The capacitor charges to its maximum value in one time constant and the current is zero at that time.
b) The potential difference across the resistor and the potential difference across the capacitor are always equal.
c) The potential difference across the resistor is always greater than the potential difference across the capacitor.
d) The potential difference across the capacitor is always greater than the potential difference across the resistor
e) Once the capacitor is essentially fully charged, There is no appreciable current in the circuit.
Answer:
e)
Explanation:
In an RC series circuit, at any time, the sum of the voltages through the resistor and the capacitor must be constant and equal to the voltage of the DC voltage source, in order to be compliant with KVL.
At= 0, as the voltage through the capacitor can't change instantaneously, all the voltage appears through the resistor, which means that a current flows, that begins to charge the capacitor, up to a point that the voltage through the capacitor is exactly equal to the DC voltage, so no current flows in the circuit anymore, and the charge in the capacitor reaches to its maximum value.
A particle with mass m = 700 g is found to be moving with velocity v vector (-3.50i cap + 2.90j cap) m/s. From the definition of the scalar product, v^2 = v vector. v vector.
a. What is the particle's kinetic energy at this time? J If the particle's velocity changes to v vector = (6.00i cap - 5.00j cap) m/s,
b. What is the net work done on the particle? J
Answer:
Explanation:
v₁² = v₁ . v₁
= ( - 3.5 i + 2.9 j ).( - 3.5 i + 2.9 j )
= 12.25 + 8.41
= 20.66 m /s
a ) kinetic energy = 1/2 m v₁²
= 1/2 x .7 x 20.66
= 7.23 J
b )
changed velocity v₂ = v₂.v₂
= (6i - 5 j ) . (6i - 5 j )
= 36 + 25
= 61 m /s
kinetic energy = 1/2 m v₂²
= 1/2 x .7 x 61
= 21.35 J
Work done = change in energy
= 21.35 - 7.23
= 14.12 J .
What is the distance in m between lines on a diffraction grating that produces a second-order maximum for 775-nm red light at an angle of 62.5°?
Answer:
The distance is [tex]d = 1.747 *10^{-6} \ m[/tex]
Explanation:
From the question we are told that
The order of maximum diffraction is m = 2
The wavelength is [tex]\lambda = 775 nm = 775 * 10^{-9} \ m[/tex]
The angle is [tex]\theta = 62.5^o[/tex]
Generally the condition for constructive interference for diffraction grating is mathematically represented as
[tex]dsin \theta = m * \lambda[/tex]
where d is the distance between the lines on a diffraction grating
So
[tex]d = \frac{m * \lambda }{sin (\theta )}[/tex]
substituting values
[tex]d = \frac{2 * 775 *1^{-9} }{sin ( 62.5 )}[/tex]
[tex]d = 1.747 *10^{-6} \ m[/tex]
A long straight wire carries a conventional current of 0.7 A. What is the approximate magnitude of the magnetic field at a location a perpendicular distance of 0.053 m from the wire due to the current in the wire
Answer:
2.64 x 10⁻⁶T
Explanation:
The magnitude of the magnetic field produced by a long straight wire carrying current is given by Biot-Savart law as follows: "The magnetic field strength is directly proportional to the current on the wire and inversely proportional to the distance from the wire". This can be written mathematically as;
B = (μ₀ I) / (2π r) ----------------(i)
B is magnetic field
I is current through the wire
r is the distance from the wire
μ₀ is the magnetic constant = 4π x 10⁻⁷Hm⁻¹
From the question;
I = 0.7A
r = 0.053m
Substitute these values into equation (i) as follows;
B = (4π x 10⁻⁷ x 0.7) / (2π x 0.053)
B = 2.64 x 10⁻⁶T
Therefore the approximate magnitude of the magnetic field at that location is 2.64 x 10⁻⁶T
A ball is thrown at 23.2 m/s inside a boxcar moving along the tracks at 34.9 m/s. What is the speed of the ball relative to the ground if the ball is thrown forward
Answer:
The speed of the ball relative to the ground if the ball is thrown forward is 58.1 m/s
Explanation:
Given;
speed of the ball thrown inside boxcar, [tex]V_B[/tex] = 23.2 m/s
speed of the boxcar moving along the tracks, [tex]V_T[/tex] = 34.9 m/s
Determine the speed of the ball relative to the ground if the ball is thrown forward.
If the ball is thrown forward, the speed of the ball relative to the ground will be sum of the ball's speed plus speed of the boxcar.
[tex]V_{relative \ speed} = V_B + V_T\\\\V_{relative \ speed} = 23.2 + 34.9\\\\V_{relative \ speed} = 58.1 \ m/s[/tex]
Therefore, the speed of the ball relative to the ground if the ball is thrown forward is 58.1 m/s.
soaring birds and glider pilots can remain aloft for hours without expending power. Discuss why this is so.
Answer:
Since their wings and body develop the drag. When there is warm air then they expand their wings. Since,soaring birds and glider pilots have no engine, they always maintain their high speed to lift their weight in air for hours without expending power by convection
Explanation:
What do Equations 1 and 2 predict will happen to the single-slit diffraction pattern (intensity, fringe width, and fringe spacing) as the slit width is increased.
Equation 1:
Sinθ = mλ/ω
Equaiton 2:
I= Io [Sinθ (πωλ/πωλ/Rλ)
Answer:
the firtz agrees with the expression for the shape of the curve of diracion of a slit
Explanation:
The diffraction phenomenon is described by the expression
a sin θ = m λ
where a is the width of the slit, t is the angle from the center of the slit, l is the wavelength and m is an integer that corresponds to the maximum diffraction.
the previous equation qualitatively describes the curve of the diffraction phenomenon the equation takes the form
I = I₀ [(sin ππ a y / R λ) / π a y / Rλ]²
I = I₀ ’[sin π a y /Rλ]²
I₀ ’= I₀ / (π a y /Rλ)²
By reviewing the two expressions given
equation 1
w sin θ = m λ
where w =a w is the slit width
we see that the firtz agrees with the expression for the shape of the curve of diracion of a slit
Equation 2
the squares are missing
A Huge water tank is 2m above the ground if the water level on it is 4.9m high and a small opening is there at the bottom then the speed of efflux of non viscous water through the opening will be
Answer:
The speed of efflux of non-viscous water through the opening will be approximately 6.263 meters per second.
Explanation:
Let assume the existence of a line of current between the water tank and the ground and, hence, the absence of heat and work interactions throughout the system. If water is approximately at rest at water tank and at atmospheric pressure ([tex]P_{atm}[/tex]), then speed of efflux of the non-viscous water is modelled after the Bernoulli's Principle:
[tex]P_{1} + \rho\cdot \frac{v_{1}^{2}}{2} + \rho\cdot g \cdot z_{1} = P_{2} + \rho\cdot \frac{v_{2}^{2}}{2} + \rho\cdot g \cdot z_{2}[/tex]
Where:
[tex]P_{1}[/tex], [tex]P_{2}[/tex] - Water total pressures inside the tank and at ground level, measured in pascals.
[tex]\rho[/tex] - Water density, measured in kilograms per cubic meter.
[tex]g[/tex] - Gravitational acceleration, measured in meters per square second.
[tex]v_{1}[/tex], [tex]v_{2}[/tex] - Water speeds inside the tank and at the ground level, measured in meters per second.
[tex]z_{1}[/tex], [tex]z_{2}[/tex] - Heights of the tank and ground level, measured in meters.
Given that [tex]P_{1} = P_{2} = P_{atm}[/tex], [tex]\rho = 1000\,\frac{kg}{m^{3}}[/tex], [tex]g = 9.807\,\frac{m}{s^{2}}[/tex], [tex]v_{1} = 0\,\frac{m}{s}[/tex], [tex]z_{1} = 6.9\,m[/tex] and [tex]z_{2} = 4.9\,m[/tex], the expression is reduced to this:
[tex]\left(9.807\,\frac{m}{s^{2}} \right)\cdot (6.9\,m) = \frac{v_{2}^{2}}{2} + \left(9.807\,\frac{m}{s^{2}} \right)\cdot (4.9\,m)[/tex]
And final speed is now calculated after clearing it:
[tex]v_{2} = \sqrt{2\cdot \left(9.807\,\frac{m}{s^{2}} \right)\cdot (6.9\,m-4.9\,m)}[/tex]
[tex]v_{2} \approx 6.263\,\frac{m}{s}[/tex]
The speed of efflux of non-viscous water through the opening will be approximately 6.263 meters per second.
A sailor strikes the side of his ship just below the surface of the sea. He hears the echo of the wave reflected from the ocean floor directly below 2.5 ss later.
How deep is the ocean at this point? (Note: Use the bulk modulus method to determine the speed of sound in this fluid, rather than using a tabluated value.)
_____ m
Answer:
1248m
The time that wave moves from the wave source to the ocean floor is half the total travel time: t = 2.5/2 = 1.25s
The speed of sound in seawater is 1560 m/s
Therefore, s = vt = (1560 m/s)(1.25s) =1248 m = 1.2km
A device called an insolation meter is used to measure the intensity of sunlight. It has an area of 100 cm2 and registers 6.50 W. What is the intensity in W/m2
Answer:
650W/m²Explanation:
Intensity of the sunlight is expressed as I = Power/cross sectional area. It is measured in W/m²
Given parameters
Power rating = 6.50Watts
Cross sectional area = 100cm²
Before we calculate the intensity, we need to convert the area to m² first.
100cm² = 10cm * 10cm
SInce 100cm = 1m
10cm = (10/100)m
10cm = 0.1m
100cm² = 0.1m * 0.1m = 0.01m²
Area (in m²) = 0.01m²
Required
Intensity of the sunlight I
I = P/A
I = 6.5/0.01
I = 650W/m²
Hence, the intensity of the sunlight in W/m² is 650W/m²
6. How would the measurements for potential difference and current change if a 200 Ω resistor was used in Circuit 1 instead of the 100 Ω resistor? Explain your answer.
Answer:
Explanation:
Resistance is defined as the opposition to the flow of an electric current in a circuit. This means that a higher amount of resistance tends to reduce the amount of current flowing through the resistance. The lower the current, the greater the possibility for the resistor to allow current to pass through it. if a 200 Ω resistor was used in Circuit 1 instead of the 100 Ω resistor, then the current in the circuit will tends to increase since we are replacing the load with a lesser resistor and a smaller resistance tends to allow more current to flow through it
For the potential difference, a decrease in the resistance value will onl decrease the potential difference flowing in the circuit according to ohm's law. According to the law the pd in a circuit is directly proportional to the current which means an increase in the resistance value will cause an increase in the corresponding pd and vice versa.
An electron, moving toward the west, enters a uniform magnetic field. Because of this field the electron curves upward. The direction of the magnetic field is
Answer:
The magnetic field's direction is towards the north
Explanation:
The force on a positive charge in a uniform magnetic field is represented by the right hand rule. To determine the direction of the force, place your right hand with your palm up, and your thumb at 90° to the other fingers. If the fingers represent the magnetic field, and the thumb the direction of the positive charge, then the palm will push up in the direction of the force. But a negative charge like an electron pushes in exactly the opposite direction. So if you follow this rule, you will find that the magnetic field points towards the north.
The direction of the magnetic field is towards the North. This can be
determined using the right hand rule by Fleming.
The right hand rule states that to determine the direction of the magnetic
force, the right thumb should be pointed in in the direction of the velocity,
index finger in the direction of the magnetic field and middle finger in the
direction of magnetic force.
When this is applied, we will discover that the index finger will point towards
the north region.
Read more on https://brainly.com/question/19904974
Two cars are moving towards each other and sound emitted by first car with real frequency of 3000 hertz is detected by a person in second with apparent frequency of 3400 Hertz what was the speed of cars
Answer:
v ’= 21.44 m / s
Explanation:
This is a doppler effect exercise that changes the frequency of the sound due to the relative movement of the source and the observer, the expression that describes the phenomenon for body approaching s
f ’= f (v + v₀) / (v-[tex]v_{s}[/tex])
where it goes is the speed of sound 343 m / s, v_{s} the speed of the source v or the speed of the observer
in this exercise both the source and the observer are moving, we will assume that both have the same speed,
v₀ = v_{s} = v ’
we substitute
f ’= f (v + v’) / (v - v ’)
f ’/ f (v-v’) = v + v ’
v (f ’/ f -1) = v’ (1 + f ’/ f)
v ’= (f’ / f-1) / (1 + f ’/ f) v
v ’= (f’-f) / (f + f’) v
let's calculate
v ’= (3400 -3000) / (3000 +3400) 343
v ’= 400/6400 343
v ’= 21.44 m / s
An apple falls from a tree and hits your head with a force of 9J. The apple weighs 0.22kg. How far did the apple fall?
Answer:
The apple fell at a distance of 4.17 m.
Explanation:
Work is defined as the force that is applied on a body to move it from one point to another. When a force is applied, an energy transfer occurs. Then it can be said that work is energy in motion.
When a net force is applied to the body or a system and this produces displacement, then that force is said to perform mechanical work.
In the International System of Units, work is measured in Joule. Joule is equivalent to Newton per meter.
The work is equal to the product of the force by the distance and by the cosine of the angle that exists between the direction of the force and the direction that travels the point or the object that moves.
Work=Force*distance* cosine(angle)
On the other hand, Newton's second law says that the acceleration of a body is proportional to the resultant of forces on it acting and inversely proportional to its mass. This is represented by:
F=m*a
where F is Force [N], m is Mass [kg] and a Acceleration [m / s²]
In this case, the acceleration corresponds to the acceleration of gravity, whose value is 9.81 m / s². So you have:
Work= 9 JF=m*a=0.22 kg*9.81 m/s²= 2.1582 Ndistance= ?angle=0 → cosine(angle)= 1Replacing:
9 J= 2.1582 N* distante* 1
Solving:
[tex]distance=\frac{9J}{2.1582 N*1}[/tex]
distance= 4.17 m
The apple fell at a distance of 4.17 m.
A hot air balloon competition requires a balloonist to drop a ribbon onto a target on the ground. Initially the hot air balloon is 50 meters above the ground and 100 meters from the target. The wind is blowing the balloon at v= 15 meters/sec on a course to travel directly over the target. The ribbon is heavy enough that any effects of the air slowing the vertical velocity of the ribbon are negligible. How long should the balloonist wait to drop the ribbon so that it will hit the target?
Answer:
The wait time is [tex]t_w = 3.4723 \ s[/tex]
Explanation:
From the question we are told that
The distance of the hot air balloon above the ground is [tex]z = 50 \ m[/tex]
The distance of the hot air balloon from the target is [tex]k = 100 \ m[/tex]
The speed of the wind is [tex]v = 15 \ m/s[/tex]
Generally the time it will take the balloon to hit the ground is
[tex]t = \sqrt{ \frac{2 * z }{g} }[/tex]
where g is acceleration due to gravity with value [tex]g = 9.8 m/s^2[/tex]
substituting values
[tex]t = \sqrt{ \frac{2 * 50 }{9.8} }[/tex]
[tex]t = 3.194 \ s[/tex]
Now at the velocity the distance it will travel before it hit the ground is mathematically represented as
[tex]d = v * t[/tex]
substituting values
[tex]d = 15 * 3.194[/tex]
[tex]d = 47.916 \ m[/tex]
Now in order for the balloon to hit the target on the ground it will need to travel b distance on air before the balloonist drops it and this b distance can be evaluated as
[tex]b = k - d[/tex]
substituting values
[tex]b =100 -47.916[/tex]
[tex]b = 52.084 \ m[/tex]
Hence the time which the balloonist need to wait before dropping the balloon is mathematically evaluated as
[tex]t_w = \frac{b}{v}[/tex]
substituting values
[tex]t_w = \frac{52.084}{15}[/tex]
[tex]t_w = 3.4723 \ s[/tex]
Consider a single turn of a coil of wire that has radius 6.00 cm and carries the current I = 1.50 A . Estimate the magnetic flux through this coil as the product of the magnetic field at the center of the coil and the area of the coil. Use this magnetic flux to estimate the self-inductance L of the coil.
Answer:
a
[tex]\phi = 1.78 *10^{-7} \ Weber[/tex]
b
[tex]L = 1.183 *10^{-7} \ H[/tex]
Explanation:
From the question we are told that
The radius is [tex]r = 6 \ cm = \frac{6}{100} = 0.06 \ m[/tex]
The current it carries is [tex]I = 1.50 \ A[/tex]
The magnetic flux of the coil is mathematically represented as
[tex]\phi = B * A[/tex]
Where B is the magnetic field which is mathematically represented as
[tex]B = \frac{\mu_o * I}{2 * r}[/tex]
Where [tex]\mu_o[/tex] is the magnetic field with a constant value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]
substituting value
[tex]B = \frac{4\pi * 10^{-7} * 1.50 }{2 * 0.06}[/tex]
[tex]B = 1.571 *10^{-5} \ T[/tex]
The area A is mathematically evaluated as
[tex]A = \pi r ^2[/tex]
substituting values
[tex]A = 3.142 * (0.06)^2[/tex]
[tex]A = 0.0113 m^2[/tex]
the magnetic flux is mathematically evaluated as
[tex]\phi = 1.571 *10^{-5} * 0.0113[/tex]
[tex]\phi = 1.78 *10^{-7} \ Weber[/tex]
The self-inductance is evaluated as
[tex]L = \frac{\phi }{I}[/tex]
substituting values
[tex]L = \frac{1.78 *10^{-7} }{1.50 }[/tex]
[tex]L = 1.183 *10^{-7} \ H[/tex]
A double-slit experiment uses coherent light of wavelength 633 nm with a slit separation of 0.100 mm and a screen placed 2.0 m away. (a)How wide on the screen is the central bright fringe
Answer:
0.0127m
Explanation:
Using
Ym= (1)(633x10^-9m)(2m) / (0.1x10^-3m) = 0.0127m
If 50 km thick crust having an average density of 3.0 g/cm3 has a surface elevation of 2.5 km above sea level, what would you predict about the surface elevation for 50 km thick crust with an average density of 2.8 g/cm3
Answer:
To calculate the predicted surface elevation of a 50km thick crust above a surface of 2.5km we are given a density of 3 gram per centimeter cube.
The displacement of the material will be calculated by subtracting the surface elevation of 2.5 km from the 50 km thick crust. Therefore 50-25= 47.5 km.
Thus let the density of the material be Pm
50*3= 47.5*Pm
Therefore: Pm= (50*3)/47.5= 3.16gram per centimeter cube
Thus with an average density of 2.8gram per centimeter cube
50*2.8= (50-x)*3.16
(50-x)= (50*2.8)/3.16
50-x=44.3
x=50-44.3= 5.7
Explanation:
To calculate the predicted surface elevation of a 50km thick crust above a surface of 2.5km we are given a density of 3 gram per centimeter cube.
The displacement of the material will be calculated by subtracting the surface elevation of 2.5 km from the 50 km thick crust. Therefore 50-25= 47.5 km.
Thus let the density of the material be Pm
50*3= 47.5*Pm
Therefore: Pm= (50*3)/47.5= 3.16gram per centimeter cube
Thus with an average density of 2.8gram per centimeter cube
50*2.8= (50-x)*3.16
(50-x)= (50*2.8)/3.16
50-x=44.3
x=50-44.3= 5.7
Find the work done in pumping gasoline that weighs 6600 newtons per cubic meter. A cylindrical gasoline tank 3 meters in diameter and 6 meters long is carried on the back of a truck and is used to fuel tractors. The axis of the tank is horizontal. The opening on the tractor tank is 5 meters above the top of the tank in the truck. Find the work done in pumping the entire contents of the fuel tank into the tractor.
Answer:
work done in pumping the entire fuel is 1399761 J
Explanation:
weight per volume of the gasoline = 6600 N/m^3
diameter of the tank = 3 m
length of the tank = 6 m
The height of the tractor tank above the top of the tank = 5 m
The total volume of the fuel is gotten below
we know that the tank is cylindrical.
we assume that the fuel completely fills the tank.
therefore, the volume of a cylinder =
where r = radius = diameter ÷ 2 = 3/2 = 1.5 m
volume of the cylinder = 3.142 x x 6 = 42.417 m^3
we then proceed to find the total weight of the fuel in Newton
total weight = (weight per volume) x volume
total weight = 6600 x 42.417 = 279952.2 N
therefore,
the work done to pump the fuel through to the 5 m height = (total weight of the fuel) x (height through which the fuel is pumped)
work done in pumping = 279952.2 x 5 = 1399761 J
A rocket rises vertically, from rest, with an acceleration of 3.2 m/s2 until it runs out of fuel at an altitude of 850 m . After this point, its acceleration is that of gravity, downward.
Answer:
v = 73.75 m/s
Explanation:
It is given that,
A rocket rises vertically, from rest, with an acceleration of 3.2 m/s² until it runs out of fuel at an altitude of 850 m.
Let us assume we need to find the velocity of the rocket when it runs out of fuel.
Let v is the final speed. Using the third equation of kinematics as :
[tex]v^2-u^2=2as[/tex]
u = 0
[tex]v=\sqrt{2as} \\\\v=\sqrt{2\times 3.2\times 850}\\\\v=73.75\ m/s[/tex]
So, the velocity of the rocket when it runs out of the fuel is 73.75 m/s