Answer:
Each of the capacitor carries the same charge, Q
Explanation:
When capacitors are connected in series, the battery voltage is divided equally across the capacitors. The total voltage across the three identical capacitors is calculated as follows;
[tex]V_T = V_1 + V_2 + V_3[/tex]
We can also calculate this voltage in terms of capacitance and charge;
[tex]V = \frac{Q}{C} \\\\V_T = V_1 + V_2 +V_3 \\\\(given \ total \ charge \ as \ Q, then \ the \ total \ voltage \ V_T \ can \ be \ written \ as)\\\\V_T = \frac{Q}{C_1} + \frac{Q}{C_2} + \frac{Q}{C_3} \\\\V_T = Q(\frac{1}{C_1 } +\frac{1}{C_2} + \frac{1}{C_3 })\\\\[/tex]
Therefore, each of the capacitor carries the same charge, Q
Ohm’s Law
pls answer this photos
Answer:
Trial 1: 2 Volts, 0 %
Trial 2: 2.8 Volts, 0%
Trial 3: 4 Volts, 0 %
Explanation:
Th experimental values are given in the table, while the theoretical value can be found by using Ohm/s Law:
V = IR
TRIAL 1:
V = IR
V = (0.1 A)(20 Ω)
V = 2 volts
% Difference = [tex]|\frac{Theoretical Value - Exprimental Value}{Theoretical Value}|[/tex] x 100%
% Difference = |(2 - 2)/2| x 100%
% Difference = 0 %
TRIAL 2:
V = IR
V = (0.14 A)(20 Ω)
V = 2.8 volts
% Difference = [tex]|\frac{Theoretical Value - Exprimental Value}{Theoretical Value}|[/tex] x 100%
% Difference = |(2.8 - 2.8)/2.8| x 100%
% Difference = 0 %
TRIAL 3:
V = IR
V = (0.2 A)(20 Ω)
V = 4 volts
% Difference = [tex]|\frac{Theoretical Value - Exprimental Value}{Theoretical Value}|[/tex] x 100%
% Difference = |(4 - 4)/4| x 100%
% Difference = 0 %
Estimate the distance (in cm) between the central bright region and the third dark fringe on a screen 6.3 m from two double slits 0.49 mm apart illuminated by 739-nm light. (give answer in millimeters)
Answer:
Explanation:
distance of third dark fringe
= 2.5 x λ D / d
where λ is wavelength of light , D is screen distance and d is slit separation
putting the given values
required distance = 2.5 x 739 x 10⁻⁹ x 6.3 / .49 x 10⁻³
= 23753.57 x 10⁻⁶
= 23.754 x 10⁻³ m
= 23.754 mm .
Two sound waves W1 and W2, of the same wavelength interfere destructively at point P. The waves originate from two in phase speakers. W1 travels 36m and W2 travels 24m before reaching point P. Which of the following values could be the wave length of the sound waves?
a. 24m
b. 12m
c. 6m
d. 4m
Answer:
a. 24 m
Explanation:
Destructive interference occurs when two waves arrive at a point, out of phase. In a completely destructive interference, the two waves cancel out, but in a partially destructive interference, they produce a wave with a time varying amplitude, but maintain a wavelength the wavelength of one of the original waves. Since the two waves does not undergo complete destructive interference, then the possible value of the new wave formed can only be 24 m, from the options given.
•• A metal sphere carrying an evenly distributed charge will have spherical equipotential surfaces surrounding it. Suppose the sphere’s radius is 50.0 cm and it carries a total charge of (a) Calculate the potential of the sphere’s surface. (b)You want to draw equipotential surfaces at intervals of 500 V outside the sphere’s surface. Calculate the distance between the first and the second equipotential surfaces, and between the 20th and 21st equipotential surfaces. (c) What does the changing spacing of the surfaces tell you about the electric field?
Answer:
Explanation:
For this exercise we will use that the potential is created by the charge inside the equinoctial surface and just like in Gauss's law we can consider all the charge concentrated in the center.
Therefore the potential on the ferric surface is
V = k Q / r
where k is the Coulomb constant, Q the charge of the sphere and r the distance from the center to the point of interest
a) On the surface the potential
V = 9 10⁹ Q / 0.5
V = 18 10⁹ Q
Unfortunately you did not write the value of the load, suppose a value to complete the calculations Q = 1 10⁻⁷ C, with this value the potential on the surfaces V = 1800 V
b) The equipotential surfaces are concentric spheres, let's look for the radii for some potentials
for V = 1300V let's find the radius
r = k Q / V
r = 9 109 1 10-7 / 1300
r = 0.69 m
other values are shown in the following table
V (V) r (m)
1800 0.5
1300 0.69
800 1,125
300 3.0
In other words, we draw concentric spheres with these radii and each one has a potential difference of 500V
C) The spacing of the spheres corresponds to lines of radii of the electric field that have the shape
E = k Q / r²
If the car decelerates uniformly along the curved road from 27 m/s m/s at A to 13 m/s m/s at C, determine the acceleration of the car at B
Answer:
0.9m/s²
Explanation:
See attached files
Three resistors, 6.0-W, 9.0-W, 15-W, are connected in parallel in a circuit. What is the equivalent resistance of this combination of resistors?
Answer:
2.9Ω
Explanation:
Resistors are said to be in parallel when they are arranged side by side such that their corresponding ends are joined together at two common junctions. The combined resistance in such arrangement of resistors is given by;
1/Req= 1/R1 + 1/R2 + 1/R3 .........+ 1/Rn
Where;
Req refers to the equivalent resistance and R1, R2, R3 .......Rn refers to resistance of individual resistors connected in parallel.
Note that;
R1= 6.0Ω
R2 = 9.0Ω
R3= 15.0 Ω
Therefore;
1/Req = 1/6 + 1/9 + 1/15
1/Req= 0.167 + 0.11 + 0.067
1/Req= 0.344
Req= (0.344)^-1
Req= 2.9Ω
The equivalent resistance of this combination of resistors is 2.9Ω.
Calculation of the equivalent resistance:The combined resistance in such arrangement of resistors is provided by;
1/Req= 1/R1 + 1/R2 + 1/R3 .........+ 1/Rn
here.
Req means the equivalent resistance and R1, R2, R3
.Rn means the resistance of individual resistors interlinked in parallel.
Also,
R1= 6.0Ω
R2 = 9.0Ω
R3= 15.0 Ω
So,
1/Req = 1/6 + 1/9 + 1/15
1/Req= 0.167 + 0.11 + 0.067
1/Req= 0.344
Req= (0.344)^-1
Req= 2.9Ω
learn more about resistance here: https://brainly.com/question/15047345
Current folw in which dirction
A 3.15-kg object is moving in a plane, with its x and y coordinates given by x = 6t2 − 4 and y = 5t3 + 6, where x and y are in meters and t is in seconds. Find the magnitude of the net force acting on this object at t = 2.15 s.
Answer:
206.67NExplanation:
The sum of force along both components x and y is expressed as;
[tex]\sum Fx = ma_x \ and \ \sum Fy = ma_y[/tex]
The magnitude of the net force which is also known as the resultant will be expressed as [tex]R =\sqrt{(\sum Fx)^2 + (\sum Fx )^2}[/tex]
To get the resultant, we need to get the sum of the forces along each components. But first lets get the acceleration along the components first.
Given the position of the object along the x-component to be x = 6t² − 4;
[tex]a_x = \frac{d^2 x }{dt^2}[/tex]
[tex]a_x = \frac{d}{dt}(\frac{dx}{dt} )\\ \\a_x = \frac{d}{dt}(6t^{2}-4 )\\\\a_x = \frac{d}{dt}(12t )\\\\a_x = 12m/s^{2}[/tex]
Similarly,
[tex]a_y = \frac{d}{dt}(\frac{dy}{dt} )\\ \\a_y = \frac{d}{dt}(5t^{3} +6 )\\\\a_y = \frac{d}{dt}(15t^{2} )\\\\a_y = 30t\\a_y \ at \ t= 2.15s; a_y = 30(2.15)\\a_y = 64.5m/s^2[/tex]
[tex]\sum F_x = 3.15 * 12 = 37.8N\\\sum F_y = 3.15 * 64.5 = 203.18N[/tex]
[tex]R = \sqrt{37.8^2+203.18^2}\\ \\R = \sqrt{1428.84+41,282.11}\\ \\R = \sqrt{42.710.95}\\ \\R = 206.67N[/tex]
Hence, the magnitude of the net force acting on this object at t = 2.15 s is approximately 206.67N
Which scientist proved experimentally that a shadow of the circular object illuminated 18. with coherent light would have a central bright spot?
A. Young
B. Fresnel
C. Poisson
D. Arago
Answer:
Your answer is( D) - Arago
It takes 144 J of work to move 1.9 C of charge from the negative plate to the positive plate of a parallel plate capacitor. What voltage difference exists between the plates
Answer:
151.58 V
Explanation:
From the question,
The work done in a circuit in moving a charge is given as,
W = 1/2QV..................... Equation 1
Where W = Work done in moving the charge, Q = The magnitude of charge, V = potential difference between the plates.
make V the subject of the equation
V = 2W/Q.................. Equation 2
Given: W = 144 J. Q = 1.9 C
Substitute into equation 2
V = 2(144)/1.9
V = 151.58 V
A boat floating in fresh water displaces 16,000 N of water. How many newtons of salt water would it displace if it floats in salt water of specific gravity 1.10
Answer:
It will displace the same weight of fresh water i.e.16000N. The point is the body 'floats'- which is the underlying assumption here, and by Archimedes Principle, for this body or vessel or whatever it may be, to float it should displace an equal weight of water
Explanation:
A string passing over a pulley has a 3.85-kg mass hanging from one end and a 2.60-kg mass hanging from the other end. The pulley is a uniform solid cylinder of radius 4.5 cm and mass 0.79 kg .
A. If the bearings of the pulley were frictionless, what would be the acceleration of the two masses?
B. In fact, it is found that if the heavier mass is given a downward speed of 0.20 m/s , it comes to rest in 6.4 s . What is the average frictional torque acting on the pulley?
Answer:
Explanation:
Let the acceleration be a of the system
T₁ and T₂ be the tension in the string attached with 3.85 and 2.6 kg of mass
for motion of 3.85 kg , applying newton's law
3.85g - T₁ = 3.85 a
for motion of 2.6 kg
T₂ - 2.6g = 2.6 a
T₂ - T₁ + 1.25 g = 6.45 a
T₁ - T₂ = 1.25 g - 6.45 a
for motion of pulley
(T₁ - T₂ ) x R = I x α where R is radius of pulley , I is its moment of inertia and α is angular acceleration
(T₁ - T₂ ) x R = 1 /2 m R² x a / R
(T₁ - T₂ ) = m x a / 2 = .79 x a / 2 = . 395 a
1.25 g - 6.45 a = .395 a
1.25 g = 6.845 a
a = 1.79 m /s²
B )
When heavier mass is given speed of .2 m /s , it comes to rest in 6.4 s
Average deceleration = .2 / 6.4 = .03125 m /s²
Total deceleration created by frictional torque = 1.79 + .03125
= 1.82125 m /s²
If R be the average frictional torque acting on the pulley
angular deceleration of pulley = a / R
= 1.82125 / .045
= 40.47 rad /s²
Now R = I x 40.47 , I is moment of inertia of pulley
= 1 /2 x .79 x .045² x 40.47
= .0323 N.m
Torque created = .0323 Nm
The acceleration of the two masses hanging from ends of the pulley is 31 m/s².
The average frictional torque acting on the pulley is 0.55 Nm.
The given parameters;
mass of the pulley, = M = 0.79 kgfirst mass, m₁ = 3.85 kgsecond mass, m₂ = 2.6 kgradius, R = 4.5 cm = 0.045 mThe acceleration of the two masses is determined by taking net torque acting on the pulley;
[tex]\tau _{net} = I \alpha[/tex]
[tex]T_1R - T_2R = I \alpha\\\\[/tex]
where;
T is the tension on both stings suspending the masses = mgI is the moment of inertia of the pulley [tex]= \frac{MR^2}{2}[/tex]α is the angular acceleration[tex]R(T_1 - T_2) = (\frac{MR^2}{2} )(\frac{a}{R} )\\\\T_1 - T_2 = (\frac{MR^2}{2} )(\frac{a}{R} ) \times \frac{1}{R} \\\\T_1 - T_2 = \frac{M}{2} \times a\\\\a = \frac{2}{M} (T_1 - T_2)[/tex]
Substitute the given parameters, to solve for the acceleration of the masses;
[tex]a = \frac{2}{M} (m_1g - m_2 g)\\\\a = \frac{2g}{M} (m_1 - m_2)\\\\a = \frac{2 \times 9.8}{0.79} (3.85 - 2.6)\\\\a = 31 \ m/s^2[/tex]
The average frictional torque acting on the pulley when the heavier mass speeds down by 0.2 m/s and stop by 6.4 s.
[tex]a = \frac{v}{t} = \frac{0.2}{6.4} = 0.031 \ m/s^2 \\\\ a_t = 31 m/s^2+ 0.031 m/s^2 = 31.031 m/s^2 \\\\\tau = I \alpha\\\\\tau = (\frac{MR^2}{2} )(\frac{a_t}{R} )\\\\\tau = (\frac{0.79 \times 0.045^2 }{2} ) (\frac{31.031}{0.045} )\\\\\tau = 0.55 \ Nm[/tex]
Learn more here:https://brainly.com/question/14008486
An electromagnetic ware has a maximum magnetic field strength of 10^-8 T at a specific place in vacuum. What is the intensity of the light at that place. μ0=4πx10^-7 WbA/m g
Answer:
[tex]I=1.19\times 10^{-2}\ W/m^2[/tex]
Explanation:
It is given that,
Maximum value of magnetic field strength, [tex]B=10^{-8}\ T[/tex]
We need to find the intensity of the light at that place.
The formula of the intensity of magnetic field is given by :
[tex]I=\dfrac{c}{2\mu _o}B^2[/tex]
c is speed of light
So,
[tex]I=\dfrac{3\times 10^8}{2\times 4\pi \times 10^{-7}}\times (10^{-8})^2\\\\I=1.19\times 10^{-2}\ W/m^2[/tex]
So, the intensity of the light is [tex]1.19\times 10^{-2}\ W/m^2[/tex].
A −3.0 nC charge is on the x-axis at x=−9 cm and a +4.0 nC charge is on the x-axis at x=16 cm. At what point or points on the y-axis is the electric potential zero?
Answer:
y = 10.2 m
Explanation:
It is given that,
Charge, [tex]q_1=-3\ nC[/tex]
It is placed at a distance of 9 cm at x axis
Charge, [tex]q_2=+4\ nC[/tex]
It is placed at a distance of 16 cm at x axis
We need to find the point on the y-axis where the electric potential zero. The net potential on y-axis is equal to 0. So,
[tex]\dfrac{kq_1}{r_1}+\dfrac{kq_2}{r_2}=0[/tex]
Here,
[tex]r_1=\sqrt{y^2+9^2} \\\\r_2=\sqrt{y^2+15^2}[/tex]
So,
[tex]\dfrac{kq_1}{r_1}=-\dfrac{kq_2}{r_2}\\\\\dfrac{q_1}{r_1}=-\dfrac{q_2}{r_2}\\\\\dfrac{-3\ nC}{\sqrt{y^2+81} }=-\dfrac{4\ nC}{\sqrt{y^2+225} }\\\\3\times \sqrt{y^2+225}=4\times \sqrt{y^2+81}[/tex]
Squaring both sides,
[tex]3\times \sqrt{y^2+225}=4\times \sqrt{y^2+81}\\\\9(y^2+225)=16\times (y^2+81)\\\\9y^2+2025=16y^2-+1296\\\\2025-1296=7y^2\\\\7y^2=729\\\\y=10.2\ m[/tex]
So, at a distance of 10.2 m on the y axis the electric potential equals 0.
According to the question,
Charge,
[tex]q_1 = -3 \ nC[/tex] (9 cm at x-axis)[tex]q_2 = +4 \ nC[/tex] (16 cm at x-axis)Now,
→ [tex]\frac{kq_1}{r_1} +\frac{kq_2}{r_2} =0[/tex]
or,
→ [tex]\frac{kq_1}{r_1} =-\frac{kq_2}{r_2}[/tex]
→ [tex]\frac{q_1}{r_1} = \frac{q_2}{r_2}[/tex]
here,
[tex]r_1 = \sqrt{y^2+81}[/tex]
[tex]r^2 = \sqrt{y^2+225}[/tex]
By substituting the values,
→ [tex]\frac{-3 }{\sqrt{y^2+225} } = -\frac{4}{\sqrt{y^2+225} }[/tex]
By applying cross-multiplication,
[tex]3\times \sqrt{y^2+225} = 4\times \sqrt{y^2+81}[/tex]
By squaring both sides, we get
→ [tex]9(y^2+225) = 16(y^2+81)[/tex]
[tex]9y^2+2025 = 16 y^2+1296[/tex]
[tex]2025-1296=7y^2[/tex]
[tex]7y^2=729[/tex]
[tex]y = 10.2 \ m[/tex]
Thus the solution above is correct.
Learn more about charge here:
https://brainly.com/question/12437696
A square coil of wire with side 8.0 cm and 50 turns sits in a uniform magnetic field that is perpendicular to the plane of the coil. The coil is pulled quickly out of the magnetic field in 0.2 s. If the resistance of the coil is 15 ohm and a current of 12 mA is induced in the coil, calculate the value of the magnetic field.
Answer:
Explanation:
area of the coil A = .08 x .08 = 64 x 10⁻⁴ m ²
flux through the coil Φ = area of coil x no of turns x magnetic field
= 64 x 10⁻⁴ x 50 x B where B is magnetic field
emf induced = dΦ / dt = ( 64 x 10⁻⁴ x 50 x B - 0 ) / .2
= 1.6 B
current induced = emf induced / resistance
12 x 10⁻³ = 1.6 B / 15
B = 112.5 x 10⁻³ T .
Suppose a space vehicle with a rest mass of 150 000 kg travels past the International Space Station at a constant speed of 2.6 x 108 m/s with respect to the I.S.S. When an observer on the I.S.S. measures the moving vehicle, her measurement of the space vehicle length is 25.0 m. Determine the relativistic mass of the space vehicle. Determine the length of the space vehicle as measured by an astronaut on the space vehicle.
Answer:
m = 300668.9 kg
L₀ = 12.47 m
Explanation:
The relativistic mass of the space vehicle is given by the following formula:
[tex]m = \frac{m_{0}}{\sqrt{1-\frac{v^{2} }{c^{2}} } }[/tex]
where,
m = relativistic mass = ?
m₀ = rest mass = 150000 kg
v = relative speed = 2.6 x 10⁸ m/s
c = speed of light = 3 x 10⁸ m/s
Therefore
[tex]m = \frac{150000kg}{\sqrt{1-\frac{(2.6 x 10^{8}m/s)^{2} }{(3 x 10^{8}m/s)^{2}} } }[/tex]
m = 300668.9 kg
Now, for rest length of vehicle:
L = L₀√(1 - v²/c²)
where,
L = Relative Length of Vehicle = 25 m
L₀ = Rest Length of Vehicle = ?
Therefore,
25 m = L₀√[1 - (2.6 x 10⁸ m/s)²/(3 x 10⁸ m/s)²]
L₀ = (25 m)(0.499)
L₀ = 12.47 m
In the 1980s, the term picowave was used to describe food irradiation in order to overcome public resistance by playing on the well-known safety of microwave radiation. Find the energy in MeV of a photon having a wavelength of a picometer.
Answer:
E = 1.24MeV
Explanation:
The photon travels at the speed of light, 3.0 × [tex]10^{8}[/tex] m/s, and given that its frequency = 1 picometer = 1.0 × [tex]10^{-12}[/tex] m.
Its energy can be determined by;
E = hf
= (hc) ÷ λ
where E is the energy, h is the Planck's constant, 6.626 × [tex]10^{-34}[/tex] Js, c is the speed of the light and f is its frequency.
Therefore,
E = (6.626 × [tex]10^{-34}[/tex]× 3.0 × [tex]10^{8}[/tex]) ÷ 1.0 × [tex]10^{-12}[/tex]
= 1.9878 × [tex]10^{-25}[/tex] ÷ 1.0 × [tex]10^{-12}[/tex]
E = 1.9878 × [tex]10^{-13}[/tex] J
But, 1 eV = 1.6 × [tex]10^{-19}[/tex] J. So that;
E = [tex]\frac{1.9878*10^{-13} }{1.6*10^{-19} }[/tex]
= 1242375 eV
∴ E = 1.24MeV
The energy of the photon is 1.24MeV.
A piece of thin uniform wire of mass m and length 3b is bent into an equilateral triangle so that each side has a length of b. Find the moment of inertia of the wire triangle about an axis perpendicular to the plane of the triangle and passing through one of its vertices.
Answer:
Mb²/2
Explanation:
Pls see attached file
A 18.0 kg electric motor is mounted on four vertical springs, each having a spring constant of 24.0 N/cm. Find the period with which the motor vibrates vertically.
Answer:
Explanation:
Total mass m = 18 kg .
Spring are parallel to each other so total spring constant
= 4 x 24 = 96 N/cm = 9600 N/m
Time period of vibration
[tex]T=2\pi\sqrt{\frac{m}{k} }[/tex]
Putting the given values
[tex]T=2\pi\sqrt{\frac{18}{9600} }[/tex]
= .27 s .
A proton that is initially at rest is accelerated through an electric potential difference of magnitude 500 V. What speed does the proton gain? (e = 1.60 × 10-19 C , mproton = 1.67 × 10-27 kg)
Answer:
[tex]3.1\times 10^{5}m/s[/tex]
Explanation:
The computation of the speed does the proton gain is shown below:
The potential difference is the difference that reflects the work done as per the unit charged
So, the work done should be
= Potential difference × Charge
Given that
Charge on a proton is
= 1.6 × 10^-19 C
Potential difference = 500 V
[tex]v= \sqrt{\frac{2.q.\Delta V}{m_{p}}} \\\\\\= \sqrt{\frac{2\times 1.6\times 10^{-19}\times 5\times 10^{2}}{1.67\times 10^{-27}}}[/tex]
[tex]v= \sqrt{9.58\times 10^{10}}m/s \\\\= 3.095\times 10^{5}m/s\\\\\approx 3.1\times 10^{5}m/s[/tex]
Simply we applied the above formulas
In a shipping yard, a crane operator attaches a cable to a 1,390 kg shipping container and then uses the crane to lift the container vertically at a constant velocity for a distance of 33 m. Determine the amount of work done (in J) by each of the following.
a) the tension in the cable.
b) the force of gravity.
Answer:
a) A = 449526 J, b) 449526 J
Explanation:
In this exercise they do not ask for the work of different elements.
Note that as the box rises at constant speed, the sum of forces is chorus, therefore
T-W = 0
T = W
T = m g
T = 1,390 9.8
T = 13622 N
Now that we have the strength we can use the definition of work
W = F .d
W = f d cos tea
a) In this case the tension is vertical and the movement is vertical, so the tension and displacement are parallel
A = A x
A = 13622 33
A = 449526 J
b) The work of the force of gravity, as the force acts in the opposite direction, the angle tea = 180
W = T x cos 180
W = - 13622 33
W = - 449526 J
Receiver maxima problem. When the receiver moves through one cycle, how many maxima of the standing wave pattern does the receiver pass through
The number of maxima of the standing wave pattern is two.
Maxima problem:At the time when the receiver moves via one cycle so here two maximas should be considered. At the time when the two waves interfere by traveling in the opposite direction through the same medium so the standing wave pattern is formed.
learn more about the waves here: https://brainly.com/question/3004869?referrer=searchResults
Suppose Young's double-slit experiment is performed in air using red light and then the apparatus is immersed in water. What happens to the interference pattern on the screen?
Answer:
The bright fringes will appear much closer together
Explanation:
Because λn = λ/n ,
And the wavelength of light in water is smaller than the wavelength of light in air. Given that the distance between bright fringes is proportional to the wavelength
A 5.00-kg object is hung from the bottom end of a vertical spring fastened to an overhead beam. The object is set into vertical oscillations having a period of 1.60 s. Find the force constant of the spring.
Answer:A7.50kg object is hung from the bottom end of a vertical spring fastened to an overhead beam. The object is set into vertical oscillations having a period of2.30s. Find the force constant of the spring.
N/m
Explanation:
From mechanics, you may recall that when the acceleration of an object is proportional to its coordinate, d2xdt2=−kmx=−ω2x , such motion is called simple harmonic motion, and the coordinate depends on time as x(t)=Acos(ωt+ϕ), where ϕ, the argument of the harmonic function at t=0, is called the phase constant. Find a similar expression for the charge q(t) on the capacitor in this circuit. Do not forget to determine the correct value of ϕ based on the initial conditions described in the problem. Express your answer in terms of q0 , L, and C. Use the cosine function in your answer.
Answer:
q = q₀ sin (wt)
Explanation:
In your statement it is not clear the type of circuit you are referring to, there are two possibilities.
1) The circuit of this problem is a system formed by an Ac voltage source and a capacitor, in this case all the voltage of the source is equal to the voltage at the terminals of the capacitor
ΔV = Δ[tex]V_{C}[/tex]
we assume that the source has a voltage of the form
ΔV = ΔV₀o sin wt
The capacitance of a capacitor is
C = q / ΔV
q = C ΔV sin wt
the current in the circuit is
i = dq / dt
i = c ΔV₀ w cos wt
if we use
cos wt = sin (wt + π / 2)
we make this change by being a resonant oscillation
we substitute
i = w C ΔV₀ sin (wt + π/2)
With this answer we see that the current in capacitor has a phase factor of π/2 with respect to the current
2) Another possible circuit is an LC circuit.
In this case the voltage alternates between the inductor and the capacitor
V_{L} + V_{C} = 0
L di / dt + q / C = 0
the current is
i = dq / dt
they ask us for a solution so that
L d²q / dt² + 1 / C q = 0
d²q / dt² + 1 / LC q = 0
this is a quadratic differential equation with solution of the form
q = A sin (wt + Ф)
to find the constant we derive the proposed solution and enter it into the equation
di / dt = Aw cos (wt + Ф)
d²i / dt²= - A w² sin (wt + Ф)
- A w² + 1 /LC A = 0
w = √ (1 / LC)
To find the phase factor, for this we use the initial conditions for t = 0
in the case of condensate for t = or the charge is zero
0 = A sin Ф
Ф = 0
q = q₀ sin (wt)
A 900 kg roller coaster car starts from rest at point A. rolls down the track, goes
around a loop (points B and C) and then flies off the inclined part of the track (point D),
Figure 2.
The dimensions are: H =80 m.
r= 15m, h=10m and theta =9.30°
Calculate the
(a) gravitational potential energy at point A.
(b) velocity at point C, if the work done to move the roller coaster from point B to C is 264870 J.
c) distance of the car land (in the horizontal direction) from point D if given the
velocity at point D is 37.06 m/s
I
Answer:
gravitational potential energy at point A.
A) The gravitational potential energy at point A is; 705600 J
B) The velocity at point C, if the work done to move the roller coaster from point B to C is 264870 J is; v = 31.295 m/s
A) Formula for gravitational potential energy is;
PE = mgh
At point A;
mass; m = 900 kg
height; h = 80 m
Thus;
PE = 900 × 9.8 × 80
PE = 705600 J
B) Kinetic energy of the roller coaster at point C is given as;
KE = PE - W
We are given Workdone; W = 264870 J
Thus;
KE = 705600 - 264870
KE = 440730 J
Thus, velocity at point C is gotten from the formula of kinetic energy;
KE = ½mv²
v = √(2KE/m)
v = √(2 × 440730/900)
v = 31.295 m/s
Read more at; https://brainly.com/question/14295020
A block of mass m is suspended by a vertically oriented spring. If the mass of a block is increased to 4m, how does the frequency of oscillation change, if at all
Answer:
The frequency will be reduced by a factor of √2/2
Explanation:
Pls see attached file
The new frequency of oscillation will be half the original frequency of oscillation of spring-block system.
Let the initial mass of block be m.
And new mass is, 4m.
The frequency of oscillating motion is defined as the number of complete oscillation made during the time interval of 1 second. The mathematical expression for the frequency of oscillation of block-spring system is given as,
[tex]f = \dfrac{1}{2 \pi}\sqrt{\dfrac{k}{m}}[/tex]
Here,
k is the spring constant.
If the mass of block increased to 4m, then the new frequency of oscillation of spring will be,
[tex]f' = \dfrac{1}{2 \pi} \sqrt{\dfrac{k}{4m}}\\\\\\f' =\dfrac{1}{2} \times \dfrac{1}{2 \pi} \sqrt{\dfrac{k}{m}}\\\\\\f' =\dfrac{1}{2} \times f[/tex]
Thus, we can conclude that the new frequency of oscillation will be half the original frequency of oscillation of spring-block system.
Learn more about the frequency of oscillation here:
https://brainly.com/question/14316711
If the speed of a "cheetah" is 150 m / s. How long does it take to cover 800 m?
Answer:
5.33333... seconds
Explanation:
800 divided by 150 is equal to 5.33333... because it is per second that the cheetah moves at 150miles, the answer is 5.3333.....
To test the resiliency of its bumper during low-speed collisions, a 2 010-kg automobile is driven into a brick wall. The car's bumper behaves like a spring with a force constant 4.00 106 N/m and compresses 3.18 cm as the car is brought to rest. What was the speed of the car before impact, assuming no mechanical energy is transformed or transferred away during impact with the wall?
Answer:
Vi = 2 m/s
Explanation:
First we find the force applied to the car by wall to stop it. We use Hooke's Law:
F = kx
where,
F = Force = ?
k = spring constant = 4 x 10⁶ N/m
x = compression = 3.18 cm = 0.0318 m
Therefore,
F = (4 x 10⁶ N/m)(0.0318 m)
F = 127200 N
but, from Newton's Second Law:
F = ma
a = F/m
where,
m = mass of car = 2010 kg
a = deceleration = ?
Therefore,
a = 127200 N/2010 kg
a = 63.28 m/s²
a = - 63.28 m/s²
negative sign due to deceleration.
Now, we use 3rd equation of motion:
2as = Vf² - Vi²
where,
s = distance traveled = 3.18 cm = 0.0318 m
Vf = Final Speed = 0 m/s
Vi = Initial Speed = ?
Therefore,
2(- 63.28 m/s²)(0.0318 m) = (0 m/s)² - Vi²
Vi = √4.02 m²/s²
Vi = 2 m/s
3) If a ball launched at an angle of 10.0 degrees above horizontal from an initial height of 1.50 meters has a final horizontal displacement of 3.00 meters, what is its launch velocity
Answer:
35.6 m
Explanation:
The given ball possesses a projectile motion from its initial height. So, the required launch velocity of the ball is 6.55 m/s.
What is launch velocity?The horizontal component of velocity during the projection of an object is known as launch velocity. It is obtained when the horizontal range is known.
Given data -
The angle of projection is, [tex]\theta = 10.0 {^\circ}[/tex].
The initial height of the projection is, h = 1.50 m.
The horizontal displacement is, R = 3.00 m.
The mathematical expression for the horizontal displacement (Range) of the projectile is given as,
[tex]R = \dfrac{u^{2} \times sin2 \theta}{g}[/tex]
here,
u is the launch velocity.
g is the gravitational acceleration.
Solving as,
[tex]u =\sqrt{\dfrac{R \times g}{sin2 \theta}}\\\\\\u =\sqrt{\dfrac{1.50 \times 9.8}{sin(2 \times 10)}}\\\\\\u =\sqrt{\dfrac{1.50 \times 9.8}{sin20^\circ}}\\\\\\u=6.55 \;\rm m/s[/tex]
Thus, we can conclude that the required launch velocity of the ball is 6.55 m/s.
Learn more about the projectile motion here:
https://brainly.com/question/11049671