Answer:
3 ohms
Explanation:
6×6/6+6 =3 .............
A standing wave experiment is performed to determine the speed of waves in a rope. The standing wave pattern shown below is established in the rope. The rope makes exactly 90 complete vibrational cycles in one minute. The speed of the waves is ____ m/s.
Answer:
The speed of the waves is __6__ m/s.
Explanation:
Given
Total number of vibrations = 90
Total time taken for 90 vibrations = 60 seconds
Frequency of the wave = 90/60 = 1.5 Hz
The length of the rope as shown in the attached figure is 6 meters
The wavelength = 6/1.5 = 4.0 meters.
As we know
v=f*w
v = velocity
f = frequency
w = wavelength
Substituting the given values we get -
speed = 6.0 m/s
The speed of the waves obtained is 6 m/s
Data obtained from the question Number of complete cycles = 90Time = 1 min = 60 sLength of rope = 6 mVelocity (v) =? How to determine the frequency Number of complete cycles (n) = 90Time (t) = 1 min = 60 sFrequency (f) =?f = n/t
f = 90 / 60
f = 1.5 Hz
How to determine the velocity
Frequency (f) = 1.5 HzLength of rope (L) = 6 mWavelength (λ) = 2L / 3 = (2×6)/3 = 4mVelocity (v) =?v = λf
v = 4 × 1.5
v = 6 m/s
Complete question
See attached photo
Learn more about wave:
https://brainly.com/question/14630790
On the Earth's surface, how much does a 100kg mass weigh? 1
Answer:
100kg
Explanation:
100kg=100kg
:P
Answer: 50 because thats the mass weight
Explanation: Its the obviouse answer.
A wave travels 1.5 m/s with a frequency of 0.45 Hz. What is the wavelength of the wave?
Answer:
3.33m
Explanation:
λ = C/f
Where,
λ (Lambda) = Wavelength in meters
c = velocity=1.5m/s
f = Frequency=0.45
λ = 1.5/0.45
=3.33m.
Spiral fracture of bone: Spiral fracture of bone occurs due to twisting of the limb, and is a very common skiing accident. The fracture plane is helical, and is very difficult to heal. Mechanically, it occurs due to an applied torsion load on the bone. Recall that a state of pure shear occurs within the material when torsion is applied on a cylinder, and the bone can be idealized as a cylinder. Let a femur bone be subjected to a torque of T 50 N-m. Assume body weight of the person to be W- 80 Kgs, while each leg is subjected to half of that weight. Given radius of the bone r 10 mm. Compute the principal stresses and shear stresses, as well as orientation of planes on which these stresses are realized.
Answer:
principal stresses :б1 = 32.62mPa б2 = 31.38mPa
Max Shear stress : 16.31 mPa
Orientation of max principle plane = 44.43°
Orientation of minimum principal plane = 134.43°
Explanation:
Given data:
Torque = 50 N-m
weight = 80 kgs
half of weight is subjected to each leg
radius of bone = 10 mm = 0.010 m
a) Determine the principal stresses and shear stress
first calculate the max shear stress ( this will occur in the outermost element
= 16T / π*d^3 where : T = 50 , d = 0.020 m
hence max shear stress = 32 mPa
next determine compressive stress
= ( 40*g) / π/4*d^2 . where : d = 0.020 m , g = 9.81
hence compressive stress = 1.24 mPa
draw and calculate the radius of Mohr's circle
radius of Mohr's circle = 32.0060
Hence principal stresses = 32.0060 ± 0.62
б1 = 32.62mPa
б2 = 31.38mPa
attached below is the remaining part of the solution
space question 50 points
Explain how sun angle and seasons vary as you move away from the equator.
Seasonal change in the angle of sunlight, caused by the tilt of the Earth's axis, is the basic mechanism that results both in warmth of the weather and in length of the day.
On the graph of voltage versus current, how do the resistors compare?
name the three major types of clouds
Answer:
Cumulus, Stratus, and Cirrus. There are three main cloud types.
Explanation:
hopes it help^_^
Visible light falls into wavelength ranges of 400-700 nm, for which 1 m = 1 × 10 9 nm . The energy and wavelength of light are related by the equation E = h c λ where E is energy in Joules, h is Planck's constant ( 6.626 × 10 − 34 J-s ), c is the speed of light ( 2.998 × 10 8 m/s ), and λ is the wavelength in m. If a visible light photon has a wavelength of 560.6 nm, what is the energy of the photon (in J)?
Given the wavelength of the visible light photon, the energy of the photon is 3.54 × 10⁻¹⁹J
Given the data in the question;
Wavelength of visible light; [tex]\lambda = 560.6 nm = 5.606*10^{-7}m[/tex]
Speed of light; [tex]c = 2.998 * 10^8 m/s[/tex]
Planck's constant; [tex]h = 6.626 * 10^{-34} J.s[/tex]
The energy and wavelength of light are related by the equation:
[tex]E = \frac{hc}{\lambda}[/tex]
Where E is energy of photon in Joules, h is Planck's constant, c is the speed of light and λ is the wavelength,
We substitute our given value into the equation
[tex]E = \frac{(6.626*10^{-34}J.s)(2.998*10^8m/s)}{5.606*10^{-7}m} \\\\E = \frac{(1.986*10^{-25}J.m}{5.606*10^{-7}m}\\\\E = 3.54 * 10^{-19}J[/tex]
Therefore, given the wavelength of the visible light photon, the energy of the photon is 3.54 × 10⁻¹⁹J
Learn more: https://brainly.com/question/14683743
Type the correct answer in each box. Round your answers to the nearest hundredth.
A ball with a mass of 1.5 kilograms is tied to the end of a rope. The ball is pulled to a height of 0.5 meters above the ground and released.
The ball has
joules of potential energy at position B. At position A, all of the energy changes to kinetic energy. The velocity of the ball at position A is
meters/second. Assume there’s no air resistance. Use g = 9.8 m/s2 , PE = m × g × h, and .
Hi there!
[tex]\large\boxed{PE = 7.35 J, \text{ }v \approx 3.13 m/s}[/tex]
To find the potential energy of the ball at B, we can use the equation:
PE = mgh
Plug the given gravity, mass, and height:
PE = (1.5)(0.5)(9.8) = 7.35 J
At A, all of this potential energy is changed to kinetic energy, so we can use the following equation:
v = √2KE/m
Plug in the solved for energy and mass:
v = √2(7.35)/1.5
Solve:
v ≈ 3.13 m/s
A 16 Ω resistor and a 6 Ω resistor are connected in series to an ideal 6 V battery.
Find the current in each resistor.
Answer in units of A.
b) Find the potential difference across the first
resistor.
Answer in units of V.
c) Find the potential difference across the second
resistor.
Answer in units of V
Answer:
(a) 0.273 A
(b) 4.368 V
(c) 1.638 V
Explanation:
From the question,
(a) Applying ohm's law
V = IR'...................... Equation 1
Where V = Voltage of the battery, I = Current in each of the resistor, R' = Total resistance of the combined resistors
Since the Two resisstors are connected in series,
(i) The same current flows through both resistors
(ii) The total resistor (R') = R₁+R₂
Therefore,
V = (R₁+R₂)I
Make I the subject of the equation
I = V/(R₁+R₂)................. Equation 2
Given: V = 6 V, R₁ = 16 Ω, R₂ = 6 Ω
Substitute into equation 2
I = 6/(16+6)
I = 6/22
I = 0.273 A
(b) The potential difference across the first resisto
V₁ = IR₁...................... Equation 3
Given: I = 0.273 A, R₁ = 16 Ω
Substitute these values into equation 3
V₁ = 0.273(16)
V₁ = 4.368 V
(c) The Potential difference across the second resistor is
V₂ = IR₂.................... Equation 4
V₂ = 0.273×6
V₂ = 1.638 V
Consider the following situation, in which a compass is influenced by not only the force of Earth's magnetic field, but also an additional applied force.
1. Which of the following is true of the angle of deflection of the compass relative to FEarth if FEarth > FApplied?
a. The angle of deflection will be exactly 45°
b. The angle of deflection will be greater than 90°
c. The angle of deflection will be less than 45°
d. The angle of deflection will be exactly 0°
e. The angle of deflection will be greater than 45° but less than 90°
2. Which of the following is true of the angle of deflection of the compass relative to FEarth if FEarth < FApplied?
a. The angle of deflection will be exactly 45°
b. The angle of deflection will be greater than 90°
c. The angle of deflection will be less than 45°
d. The angle of deflection will be exactly 0°
e. The angle of deflection will be greater than 45° but less than 90°
Answer:
1) The angle of deflection will be less than 45° ( C )
2) The angle of deflection will be greater than 45° but less than 90° ( E )
Explanation:
1) Assuming that the force applied has a direction which is perpendicular to the Earth's magnetic field
∴ Fearth > Fapplied hence the angle of deflection will be < 45°
2) when the Fearth < Fapplied
the angle of deflection will be : > 45° but < 90°
A long conducting cylinder of radius a carrying a total charge +q is surrounded by a
concentric thin conducting cylindrical shell of radius b carrying a total charge -2q.
Draw the cross section of this arrangement. Use Gauss’s law to find the electric field
strength at a point r away from the axis,
Answer:
I don't know this, sorry
Which theory states that the principle cause of forgetting is passage of time? A. motivated forgetting B. retrieval failure C. decay theory D. ineffective encoding
Two loudspeakers placed 6.0 m apart are driven in phase by an audio oscillator whose frequency range is 2193 Hz to 2967 Hz. A point P is located 4.4 m from one loudspeaker and 3.6 m from the other. The speed of sound is 344 m/s. The frequency produced by the oscillator, for which constructive interference of sound occurs at point P, is closest to
Answer:
"2580 Hz" is the correct solution.
Explanation:
According to the question,
The path difference,
= [tex]4.4 - 3.6[/tex]
= [tex]0.80 \ m[/tex]
Speed,
= 344 m/s
For constructive interference,
⇒ [tex]Path \ difference =n\times \frac{Speed}{frequency}[/tex]
On substituting the values, we get
⇒ [tex]0.80=n\times \frac{344}{frequency}[/tex]
⇒ [tex]frequency=n\times 430[/tex]
⇒ [tex]n=\frac{frequency}{430}[/tex]
If the frequency range is,
f = 2193,
⇒ [tex]n=\frac{2193}{430}[/tex]
[tex]=5.1[/tex]
If the frequency range is,
f = 2967,
⇒ [tex]n=\frac{2967}{430}[/tex]
[tex]=6.9[/tex]
hence,
For n = 6, the frequency will be:
⇒ [tex]Frequency=n\times 430[/tex]
[tex]=6\times 430[/tex]
[tex]=2580 \ Hz[/tex]
pls help giving brainliest!
• Explain how Ohm's Law is like a river.
o What represents Voltage?
o What represents Current?
o What represents Resistance?
Answer:
Pressure of water = Voltage
Flow rate of water = Current
Obstructions present in the river = Resistance
Explanation:
We can describe Ohm's Law by using the river analogy,
The flow of water from a mountain to lower parts can be considered as change from high potential to a lower potential.The flow of water can also be considered as flow of electrons, that is current in a circuitThere are also obstructions in rivers that can be considered as resistance in an electric circuit.
Can someone please help me with this one
Answer:
im pretty sure the answer is A. up but im not 100% sure
5) Unlike the five big mass extinctions in the geological record, the current wave of extinctions is
caused by
A.
Human activity
В. Volcanism
C.
Sea level changes
D.
Changes in ocean chemistry
E Asteroid impact
Answer:
B.Volcanism
Explanation:
Cause every time the current wave moves is causes and eruption
Unlike the five big mass extinctions in the geological record, the current wave of extinctions is caused by the Volcanism. Thus, the correct option is B.
What is the cause of Mass extinction?A mass extinction event is also known as biotic crisis. It is a widespread and rapid decrease in the biodiversity on the Earth which could be due to various reasons. Such an extinction event is identified by a sharp change or decrease in the diversity and abundance of multicellular organisms in an area.
Past mass extinctions on this planet were caused due to extreme temperature changes, rise or fall in the sea levels and catastrophic events, one-off events like a huge volcano erupting or an asteroid hitting the Earth. The current wave of extinctions is caused by volcanism.
Therefore, the correct option is B.
Learn more about Mass extinctions here:
https://brainly.com/question/11872946
#SPJ6
At what rate is work done if the 250 Newton object from number six is moved into a hot at 4 m in four seconds
Answer:
250w
Explanation:
W=Fd
W= 250 x 4= 1000J
P=E/t=1000/4s=250w
How much current is drawn by a television
with a resistance of 43 Ω that is connected
across a potential difference of 112 V?
Answer in units of A.
Answer:
Explanation:
v = ir
v/r = i
112/43 = i
2.60 ≈ i
9
A canoe with a mass of 120 kg is floating downriver at a speed of 2.5 m/s. What is the canoe's kinetic eergy?
Answer:
K.E. = ½ × mv²
= ½ × 120 × (2.5)²
= 60 × 6.25
= 375 J
A 125-g coin is placed 8.0 cm from the axis of rotation of a horizontally rotating turntable as shown. The coefficient of static friction between the coin and the turntable is μs . The turntable makes exactly 1.0 revolution per second and the coin remains in place without slipping. [a] (8 pts) Draw a free-body force diagram for the coin. [b] (10pts)What is the frictional force acting on the coin? [c] (12pts)When the rotational speed is increased to 1.2 revolutions per second, the coin starts to slip. Calculate the coefficient of static friction μs between the coin and the turntable?
Answer:
zhvshshisvdiscdoscd if vdidg
state and explain newton second law of motion also describe the concept of force, represent it quantiatively and derive the unit of force
this is a long question only answer if you know how to solve it you will be REWARDED with points
Explanation:
Newton's second law of motion states F=ma which means force is equal to mass multiplied by acceleration which in simple terms means If you give mass force it will accelerate the concept of force in physics is any interaction that when unopposed will change the motion of an object.
Water is to be heated from 10°C to 80°C as it flows through a 2-cm-internal-diameter, 13-m-long tube. The tube is equipped with an electric resistance heater, which provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat generated in the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 5 L/min, determine the power rating of the resistance heater. Also, estimate the inner surface temperature of the pipe at the exit.
Answer:
- the power rating of the resistance heater is 24139.5 W
- the inner surface temperature of the pipe at the exit is 96.34°C
Explanation:
Given the data in the question;
Flow rate of water in the tube V" = 5L/min = 8.333 × 10⁻⁵ m³/s
The water is to be heated from 10°C to 80°C;
so Average or mean temperature [tex]T_{avg[/tex] will be;
[tex]T_{avg[/tex] = (T₁ + T₂) / 2 = (10 + 80) / 2 = 90/2 = 45°C
Now, from the Table " Properties of Water " at average temperature;
at [tex]T_{avg[/tex] = 45°C
density p = 990.1 kg/m³
specific heat [tex]C_p[/tex] = 4180 J/kg-k
thermal conductivity k = 0.637 W/m-°C
Now, we determine the mass flow;
m" = pV"
we substitute
m" = 990.1 × 8.333 × 10⁻⁵
m" = 0.08250 kg/s
we know that the power rating of the resistance heater is equal to the heat transfer rate to the water;
Q' = m"[tex]C_p[/tex]( T₂ - T₁ )
we substitute
Q' = (0.08250 × 4180 ) ( 80 - 10 )
Q' = 344.85 × 70
Q' = 24139.5 W
Hence, the power rating of the resistance heater is 24139.5 W
Next, we determine the average velocity of water in the tube;
[tex]V_{avg[/tex] = V" / [tex]A_c[/tex]
[tex]V_{avg[/tex] = V" / ( [tex]\frac{1}{4}[/tex]πD² )
given that; flows through a 2-cm-internal-diameter; D = 0.02 m
we substitute
[tex]V_{avg[/tex] = (8.333 × 10⁻⁵) / ( [tex]\frac{1}{4}[/tex]π × (0.02)² )
[tex]V_{avg[/tex] = (8.333 × 10⁻⁵) / ( 3.14159 × 10⁻⁴ )
[tex]V_{avg[/tex] = 0.265 m/s
Also, from table " saturated water property table "
At 45°C
viscosity μ = 0.596 × 10⁻³ kg/m-s
Prandtl number Pr = 3.91
Now, we determine the kinematic viscosity
v = μ / p
we substitute
v = ( 0.596 × 10⁻³ ) / 990.1
v = 6.01959 × 10⁻⁷ m²/s
so, Reynolds number in the flow region will be;
Re = ([tex]V_{avg[/tex] × D) / v
we substitute
Re = ( 0.265 × 0.02) / (6.01959 × 10⁻⁷)
Re = 8804.586
we can see that our Reynolds number ( 8804.586 ) more than 2300 and less than 10,000.
Hydraulic and thermal entry length are equal in this flow region,
such that;
[tex]L_h[/tex] = [tex]L_t[/tex]
⇒ 10 × D = 10 × 0.02 = 0.2 m
we can see that the entry length ( 0.2 m ) is smaller than the given length ( 13 m ) in the question; the flow is a turbulent flow.
So we the Nuddelt number
Nu = [tex]0.023Re^{0.8} Pr^{0.4[/tex]
Nu = 0.023 × [tex]8804.586^{0.8[/tex] × [tex]3.91^{0.4[/tex]
Nu = 56.8
Hence, the heat transfer coefficient h will be;
h = [tex]\frac{k}{D}[/tex] × Nu
we substitute
h = [tex]\frac{0.637}{0.02}[/tex] × 56.8
h = 31.85 × 56.8
h = 1809.1 W/m²-°C
Now, area of the heat transfer will be
A[tex]_s[/tex] = πDL
we substitute
A[tex]_s[/tex] = π × 0.02 × 13
A[tex]_s[/tex] = 0.8168 m²
Finally we determine the inner temperature of the pipe at exit. using the relation;
Q' = hA[tex]_s[/tex]( T₃ - T₂ )
we substitute
24139.5 = 1809.1 × 0.8168( T₃ - 10 )
24139.5 = 1477.67288( T₃ - 80 )
24139.5 = 1477.67288T₃ - 118213.8304
24139.5 + 118213.8304 = 1477.67288T₃
1477.67288T₃ = 142353.3304
T₃ = 142353.3304 / 1477.67288T
T₃ = 96.34°C
Therefore, the inner surface temperature of the pipe at the exit is 96.34°C
money is rare? or is it bad
Answer:
money is not rare. you can find it everywhere. what exactly is the question? whether it is bad or not is an opinion.
Explanation:
During the course of a demonstration the professor is called away. When he returns he finds a beaker of water that was at room temperature is now at a slightly higher temperature. There is a stirring rod on the desk and a cigarette lighter. The professor can assume that the temperature increase is due to either heat added or mechanical work done. mechanical work done on the system. heat added to the system.
Answer:
Either heat added or mechanical work done.
Explanation:
Since he found stirring rod on the desk and a cigarette lighter. This means that the beaker was probably either heated with the aid of fire from the lighter.
Also, the stirring rod could have been used to stir the water which will increase the kinetic energy which also means an increase in temperature.
Thus, it's either heat was added or mechanical work was done as a result of stirring.
A swift blow with the hand can break a pine board. As the hand hits the board, the kinetic energy of the hand is trans- formed into elastic potential energy of the bending board, if the board bends far enough, it breaks. Applying a force to the center of a particular pine board deflects the center of the board by a distance that increases in proportion to the fore. Ultimately the board breaks at an applied force of 800 N and a deflection of 1.2 cm.
a. To break the board with a blow from the hand, how fast must the hand be moving? Use 0.50 kg for the mass of the hand.
b. If the hand is moving this fast and comes to rest in a dis- tance of 1.2 cm, what is the average force on the hand?
(a) The velocity is "6.2 m/s".
(b) The average force is "800.83 N".
According to the question,
Force,
F = 800 NDeflection,
x = 1.2 cm= [tex]1.2\times 10^{-2} \ m[/tex]
As we know,
The work done,
→ [tex]W = F\times d[/tex]
[tex]= 800\times 1.2\times 10^{-2}[/tex]
[tex]= 9.6 \ J[/tex]
(a)
Given:
Mass of hand,
m = 0.50 kgNow,
→ [tex]\frac{1}{2} mv^2 = 9.6 \ J[/tex]
[tex]v = \sqrt{\frac{2\times 9.6}{0.50} }[/tex]
[tex]= 6.2 \ m/s[/tex]
(b)
→ [tex]v^2 = u^2 +2ax[/tex]
→ [tex]a= \frac{v^2}{2x}[/tex]
[tex]= \frac{(6.2)^2}{2\times 1.2\times 10^{-2}}[/tex]
[tex]= 1601.67 \ m/s^2[/tex]
hence,
The average force will be:
→ [tex]F_{avg} = m\times a[/tex]
[tex]= 0.50\times 1601.67[/tex]
[tex]= 800.83 \ N[/tex]
Thus the above answers are correct.
Learn more:
https://brainly.com/question/23115729
a student throws a coin vertically downward frok the top of a building. the coin leaves the throwers hand with a speed of 15.0m/s. what is its speed after falling freely for 2.00s?
Answer:
Final speed after 2 seconds = 34.6 m/s
Explanation:
Given:
Initial speed of coin (u) = 15 m/s
Time taken = 2 seconds
Find:
Final speed after 2 seconds
Computation:
Gravitational acceleration of earth = 9.8 m/s²
Using first equation of motion;
v = u + at
or
v = u + gt
where,
v = final velocity
u = initial velocity
g = Gravitational acceleration
t = time taken
v = 15 + 9.8(2)
v = 15 + 19.6
Final speed after 2 seconds = 34.6 m/s
5. How does a jack make changing a tire easier?
Answer: An jack makes changing a tire easier because it lifts up the car to get the tire off of the ground.
Explanation:
imagine a single charge creating an electric field. what is the relationship between electric field strength and the distance from the charge?
a. direct
b. inverse
c. inverse squared
d. indirect
Answer:
b. inverse
Explanation:
[tex]E = \frac{V}{d} \\ d \: is \: the \: distance \\ [/tex]
Rudy plans to conduct an experiment using three rosebushes of the same variety and size. His hypothesis is that the plant
receiving the most sunlight at the end of three months will show the most growth. In his plan below, he has listed how much
water, fertilizer, and sunlight each plant will receive. Why is his experiment flawed?
Answer: B) He has too many independent variables.
Explanation: Nothing in the experiment is a constant or being measured.