Which of the following describes what environmental engineers study?

ways to improve resources and materials
ways to improve our health and well-being
ways to improve compliance and sustainability
ways to improve costs and designs

The power requirement for the compressor is c. –195kw.

To determine the power requirement for the compressor, we shall apply the first law of thermodynamics for steady flow processes, which states:

ΔH = Q - W

where:

ΔH = the change in enthalpy of the system,

Q = the heat transfer to the system, and

W = the work done by the system.

Assuming air to be an ideal gas, we can use the following equations:

h1 = cpT1 and h2 = cpT2,

where:

h = the specific enthalpy,

c = the specific heat at constant pressure,

T = the absolute temperature.

And for an adiabatic steady flow process (no heat transfer), we have:

h1 + (V1²)/2 + gZ1 = h2 + (V2²)/2 + gZ2

where:

V = the specific volume

Z = the elevation.

Combining these equations and using the given data, calculate the work done by the compressor:

W = h1 - h2 = cp(T2 - T1) = cpΔT

where ΔT = T2 - T1 = 90 C = 363 K (since temperature must be in absolute units).

From the ideal gas law, calculate the specific volume of the air at the inlet and outlet of the compressor:

V1 = RT1/P1 and V2 = RT2/P2

where R = the specific gas constant.

Substituting the values and using the given flow rate, calculate the mass flow rate of the air:

m = ρV = P/(RT)V = P/(RT)(nR/P)*T = n

where:

ρ = the density,

n = the number of moles of air,

and we have used the ideal gas law again.

Now, calculate the power requirement of the compressor:

P = Wm = cpΔTn

Substituting the values:

P = (1.005 kJ/kg-K)(363 K)(10/0.001)*(1/60)

= -195 kW (since work is done by the system)

Therefore, the power requirement for the compressor is -195 kW.

Learn more about the law of thermodynamics at brainly.com/question/12976653

#SPJ4

The maximum average normal stress in each of the links is: σ = (25lbs) / (1/32 sq. in.) = 1600 psi Since the stress is determined by the cross-sectional area, and not the direction of the force, the stress is compressive for both links.

To determine the maximum average normal stress in links CD and BE, we will first calculate the cross-sectional area of the links and the area of the pins. Then, we will divide the force P by these areas to find the stress in each link and identify whether it is tensile or compressive.
1. Cross-sectional area of links CD and BE:
A = width × height = (1/8) × (1/4) = 1/32 in²
2. Diameter of pins at C, D, B, and E:
D = 1/4 in
Since both links have the same cross-sectional area, they will experience the same normal stress.
3. Calculate the maximum average normal stress in links CD and BE:
σ = P/A = (50 lbs) / (1/32 in²) = 1600 psi
As there is no information provided on the direction of force P, we cannot determine if the stress in each link is tensile or compressive. If P causes tension in the links (pulling them apart), the stress would be tensile. If P causes compression (pushing them together), the stress would be compressive.

Learn more about tensile here: https://brainly.com/question/14293634

#SPJ11

The correct answer to the question is a. 99.99 percent The EPA, or Environmental Protection Agency, is responsible for regulating the disposal of hazardous waste in the United States. One of the requirements for toxic waste incinerators is to achieve a destruction and removal rate, or DRE, before the material can be safely landfilled.

The DRE represents the percentage of hazardous waste that is destroyed through the incineration process. This means that the incinerator must be able to destroy at least 99.99 percent of the hazardous waste before it can be disposed of in a landfill. This high DRE requirement ensures that as little hazardous waste as possible is left over after incineration, minimizing the risk of environmental contamination and harm to public health.

In summary, the EPA requires a high DRE rate for toxic waste incinerators to ensure that hazardous waste is effectively and safely disposed of, minimizing the risk of waste-related environmental destruction and harm.

Learn more about toxic here:

https://brainly.com/question/7316107

#SPJ11

The frequency is given as 94.45 GHz

In various areas of science and engineering, such as electromagnetism, mechanics, and signal processing, frequency plays a significant role. It signifies the number of times that an event occurs within a certain time frame.

The field of physics describes it as the number of cycles present in a wave pattern for every second, quantified in Hertz (Hz). For instance, if a soundwave undergoes 440 cycles per second, its frequency equals to 440 Hz - this measurement system is immensely vital in understanding periodic occurrences.

Read more about frequency here:

https://brainly.com/question/254161

#SPJ4

Answer:  the correct option is B. ",".

Explanation: the argument that should be sent to the split() method to get the names as elements in a list is "," (comma).

The drawings that answer the question is given below:

The static pressure of a fluid on an object occurs whilst the liquid is still, or in motion at a steady pace. As it does not move related to the item, it is given its name "static".

This critical parameter holds significance within the realm of fluid mechanics, especially when designing structures such as pipelines, buildings, and aircraft wings.

Equally important, it plays a central role in ensuring devices such as compressors, turbines, and pumps operate with optimal performance while measuring devices exists that assess the static pressure - examples include both manometers and pressure gauges.

Read more about static pressure here:

https://brainly.com/question/31385837

#SPJ4

The single statement required is;

fgets (streetAddress, ADDRESS_SIZE_LIMIT, stdin); printf ("You entered: %s", streetAddress);

The process of accepting user input in C requires careful attention; avoiding errors related to overflows and determining bulletproof approaches necessitate developers' consideration. The implementation proposed here utilizes a function called fgets().

When executed with the requisite parameters (input stream, maximum character length allowed per string, and an output buffer), it easily captures whole lines from standard inputs.

Employing BUFFER_SIZE_LIMIT-50 prevents errors resulting from overflow situations during data entry.

Learn more about Statement:
https://brainly.com/question/29896309
#SPJ1

To address the concern of the steel nozzle exceeding the maximum allowable operating temperature during transient operation of the rocket engine, a ceramic thermal barrier coating is proposed.

This coating has a low thermal conductivity (k) and can therefore provide insulation to the steel nozzle. The use of such a coating can help to reduce the heat transfer from the combustion gases to the nozzle and thus extend the duration of engine operation. It is important to note that the effectiveness of the coating will depend on its thickness, composition, and adhesion to the steel substrate. Therefore, careful consideration must be given to the selection and application of the ceramic coating to ensure optimal performance and durability under the operating conditions of the rocket engine.

Learn more about  conductivity here: https://brainly.com/question/12136944

#SPJ11

Personnel must be clearly identified and labelled in plain English to ensure that they can be easily recognized and located in case of emergency or other situations. The use of armbands, vests, helmets, or other similar items in corresponding colours can help identify personnel by their roles or responsibilities.

In this case, the corresponding colours for each position are:Management: Yellow. This colour is commonly used to identify personnel in a supervisory or managerial role, as well as those responsible for making decisions.Medical: Green. This colour is often used to identify personnel with medical training, such as doctors, nurses, and emergency medical technicians.Safety: Orange. This colour is frequently used to identify personnel responsible for maintaining safety and preventing accidents, such as safety officers, inspectors, or engineers.It is important to ensure that all personnel understand the meaning of the colours and symbols used to identify different roles or responsibilities to ensure that they can be quickly identified and located when needed.

To learn more about responsibilities  click on the link below:

brainly.com/question/30432882

#SPJ11

The Startek info helps Mercedes Benz in several ways such as

Diagnostic Procedures

Repair Instructions

Technical Bulletins

Wiring Diagrams

Parts Information

Given data:

Startek Info is an online platform that provides technical information and resources to Mercedes-Benz technicians. It is designed to assist technicians in diagnosing and repairing Mercedes-Benz vehicles by providing access to detailed repair instructions, technical bulletins, wiring diagrams, diagnostic procedures, and other relevant information.

Diagnostic Procedures

Repair Instructions

Technical Bulletins

Wiring Diagrams

Parts Information

Startek Info assists Mercedes-Benz technicians in their daily work, enhancing their ability to diagnose and repair vehicles accurately and efficiently.

To learn more about Mercedes Benz, refer:

https://brainly.com/question/32137206

#SPJ6

To find ix and iy for the shaded area shown using integration and the composite body approach, we can follow the steps outlined in textbook problems 9.93 and 9.44.

First, we need to determine the shape of the composite body. Looking at the shaded area, we can see that it consists of two rectangles and a triangular section. We can combine these shapes to form a composite body that is rectangular at the bottom and triangular at the top.

Next, we need to find the coordinates of the centroid of the composite body. We can do this by finding the individual centroids of the rectangular and triangular sections and then using the weighted average method. The centroid of a rectangle is located at the center of the rectangle, so we can easily find the x and y coordinates of the centroid of the rectangular section. The centroid of a triangle is located at the intersection of its medians, which can be found using basic geometry. Once we have the coordinates of the centroids for each section, we can use the weighted average method to find the coordinates of the centroid of the composite body.

Once we have the coordinates of the centroid, we can use integration to find ix and iy. We can break up the composite body into small horizontal strips and use the formula for the moment of inertia of a rectangle and the moment of inertia of a triangle to find the contribution of each strip to the overall moment of inertia. We can then sum up these contributions using integration to find the total moment of inertia of the composite body about the x and y axes.

Overall, the process of finding ix and iy for a composite body using integration and the composite body approach can be a bit involved, but it is a useful tool for analyzing complex shapes. By breaking up a shape into simpler sections and using basic geometry and calculus, we can determine its properties and better understand how it will behave under different conditions.

To learn more about integration visit;

brainly.com/question/30900582

#SPJ11

The angled crib configuration offers several advantages for both parents and babies.

First, it can help reduce the risk of reflux and colic by positioning the baby's head slightly elevated, which can promote better digestion and more restful sleep. Additionally, the angled design can make it easier for parents to access and soothe their baby during the night, as they don't need to lean over as far or disturb the baby's sleep as much. Finally, angled cribs can also be beneficial for babies with respiratory issues or congestion, as the elevated position can help clear the airways and improve breathing. Overall, the angled crib configuration can provide a more comfortable and convenient sleep solution for both parents and babies.

To learn more about crib visit;

https://brainly.com/question/13629165

#SPJ11

The charge on the capacitor at instant t=0.75 sec is 3.19 mc.

A capacitor is a two-terminal electrical device that can store energy in the form of an electric charge. It consists of two electrical conductors that are separated by a distance.

So, at any time the charge is given.

Q(t') = Qe + Cv² (1-e-t/e)

Now, So, at we t = 0.75 sec, com write: t = 0.75 - 0.50= 0.25

Q(t) = 5000 (1-e^-0·5)e-025 + 50×150 (1- e^-0.25)

= 3191.16

=3.19

Learn more about capacitor on

https://brainly.com/question/27393410

#SPJ1

The weir loading rate is 225 m³/m-day.

we Solve for the surface area first

Overflow rate = 25 m³/m²-day

Flow rate = 900 m³/day

Surface area (A) = Flow rate / Overflow rate

A = 900 m³/day / 25 m³/m²-day

A = 36 m²

Solve for length of clarifier

Width (W) = 4.0 m

Length (L) = Surface area / Width

L = 36 m² / 4.0 m

L = 9.0 m

Solve for detention time

Volume (V) = Length * Width * Depth

V = 9.0 m * 4.0 m * 3.2 m

V = 115.2 m³

Detention time (t) = Volume / Flow rate

t = 115.2 m³ / 900 m³/day

t = 0.128 days

weir loading rate:

Given: Only one end weir is used

Weir length (L_w) = Width of the tank

L_w = 4.0 m

Weir loading rate (WLR) = Flow rate / Weir length

WLR = 900 m³/day / 4.0 m

WLR = 225 m³/m-day

The weir loading rate is 225 m³/m-day.

Read more on overflow rate here:https://brainly.com/question/30891124

#SPJ4

The oil window is the temperature range in which organic matter is converted to petroleum without destroying it. This temperature range lies between 30 to 60 °C.

It is important to note that this temperature range is specific to the type of organic matter being converted and the specific geological conditions present in a given area. Temperature is a critical factor in the formation of petroleum as it controls the rate of chemical reactions that transform the organic matter into hydrocarbons. If the temperature is too high, the organic matter will be destroyed, and if it is too low, the reactions will not occur at a significant rate. Therefore, understanding the oil window is crucial in determining the potential for petroleum formation in a particular geological region.

To learn more about temperature visit;

https://brainly.com/question/11464844

#SPJ11

The code seen in Example 5-25 reads information from a text file containing the subjects' names, ID numbers along with their individual vote totals.

Afterward, it sums up the entire set of votes per person, and projects each name followed by their overall vote tally.

To effectively validate the code, one must create a data file that accompanies the code, preferably with the identical formatting as expected by the program. Once running, the output should manifest the names together with each of their corresponding total amount of votes received.

Read more about programs here:

https://brainly.com/question/1538272

#SPJ4

Tendons, which are tough fibrous cords that connect muscles to bones, must be securely supported to prevent injuries and ensure proper functioning of the musculoskeletal system. The support of tendons is crucial for maintaining stability and range of motion in the joints, especially during physical activities such as running, jumping, or lifting weights.

The degree of support required for tendons may vary depending on the location and function of the tendon. Some tendons, such as those in the fingers or wrist, may require less support as they are smaller and less prone to stress injuries. However, tendons in larger joints such as the knee, ankle, or shoulder may require more support due to the higher load and impact they sustain.

Tendon support can be achieved through various methods such as braces, compression garments, taping, and physical therapy exercises. These techniques aim to provide stability and reduce the risk of injury by minimizing the strain and pressure on the tendons.

In summary, tendons must be securely supported to prevent injury and ensure optimal performance of the musculoskeletal system. The level of support needed may vary depending on the location and function of the tendon, but no less than adequate support should be provided to maintain joint stability and prevent damage.

Learn more about Tendons here:

https://brainly.com/question/29850619

#SPJ11

Douglas Fir, when loaded parallel to the grain, will start to fail at approximately 7,500 pounds per square inch (psi) of compressive stress. However, the exact point of failure will depend on various factors, including the specific grade of the Douglas Fir, its moisture content, and the type of loading applied.

On average, Douglas Fir loaded parallel to the grain can start to fail at stress levels ranging from 1200 to 1500 pounds per square inch (psi), depending on the specific conditions. However, it's important to note that this is a general estimate and should not be solely relied upon for structural design. To accurately determine the exact point of failure for Douglas Fir loaded parallel to the grain, it's critical to consult relevant design codes, standards, and engineering calculations, and involve a qualified structural engineer or other experienced professionals to ensure safe and reliable structural design and construction practices.

learn more about Douglas Fir here:

https://brainly.com/question/13950816

#SPJ11

The statement "using namespace std;" is actually specific to the C++ programming language.

It is used to simplify the code by telling the compiler that all the standard library functions and objects should be included in the global namespace. This means that the programmer does not need to prefix every standard library function or object with "std::". When it comes to input and output, the C++ language has specific functions for this purpose, such as "cin" and "cout". These functions are part of the standard library and are included in the "iostream" header file. The "using namespace std;" statement tells the compiler to include this header file, along with other standard library header files that may be required. In terms of getting the definitions of certain objects, such as variables, this is usually done through the use of header files that contain class definitions and function prototypes.

When a program includes a header file, it can access the objects and functions defined within it. The "using namespace std;" statement does not directly impact this process, but it does make it easier to use standard library objects and functions by avoiding the need to qualify them with the "std::" prefix.  In summary, the "using namespace std;" statement is specific to the C++ programming language and is used to simplify the code by including standard library functions and objects in the global namespace. It does not directly impact input/output or the definition of variables, but it can make it easier to use standard library objects and functions.

Learn more about programming here: https://brainly.com/question/28449122

#SPJ11

Thus, there are 8 zeros at the end of (20!)² when it is written in decimal form.

The number of zeros at the end of (20!)² in decimal form can be determined by finding the number of factors of 10 in its prime factorization. We can find the prime factorization of (20!)2 by finding the prime factorization of 20! and then squaring it.

To find the prime factorization of 20!, we can count the number of factors of 2 and 5 that appear in its prime factorization. Since there are more factors of 2 than 5, we only need to count the number of factors of 5.

There are 4 factors of 5 in the prime factorization of 20! (5, 10, 15, and 20).

Therefore, the prime factorization of 20! is 2^18 * 3^8 * 5^4 * 7^2 * 11 * 13 * 17 * 19.

Squaring this prime factorization gives us (20!)² = 2^36 * 3^16 * 5^8 * 7^4 * 11^2 * 13^2 * 17^2 * 19^2. We can see that there are 8 factors of 5 in this prime factorization, so there are 8 zeros at the end of (20!)2 when it is written in decimal form.

Therefore, there are 8 zeros at the end of (20!)² when it is written in decimal form.

Know more about the prime factorization.

https://brainly.com/question/18187355

#SPJ11

To determine the flow rate of water in a 2-m-diameter circular channel laid on a grade of 1.75 m/km and made of finished concrete is calculated as 3.93 [tex]m^3/s.[/tex]

We can use the Manning equation can be expressed as:Q = [tex](1/n) * A * R^(2/3) * S^(1/2)[/tex]

Where Q is the flow rate, n is the Manning roughness coefficient, A is the cross-sectional area of the channel, R is the hydraulic radius, and S is the slope of the channel.

Assuming that the channel is running half-full, the cross-sectional area can be calculated as:

A = [tex](π/4) * D^2 * sinθ[/tex]

A =[tex](π/4) * (2m)^2 * sin(180°/2)[/tex]

A = [tex]1.57 m^2[/tex]

The hydraulic radius can be calculated as:

R = A/P

R =[tex]A/(π*D)[/tex]

R = 0.25 m

Given that the slope of the channel is 1.75 m/km or 0.00175, and assuming a roughness coefficient of 0.013 for finished concrete channels, the flow rate can be calculated as:

Q = [tex](1/0.013) * 1.57 * (0.25)^(2/3) * (0.00175)^(1/2)[/tex]

Q = [tex]3.93 m^3/s[/tex]

Therefore, the flow rate of water in the given channel is 3.93 [tex]m^3/s.[/tex]

For more questions on flow rate

https://brainly.com/question/30618961

#SPJ11

If a bubble sort of 5000 elements, takes 8 seconds, it  will take  240 seconds to sort 15000 bubble  elements.

It takes a bubble sort of 5000 elements, takes 8 seconds

it will take 15000 x 8 seconds / 5000 elements to sort 15000 elements

=  15000 x 8 seconds / 5000  

= 240 seconds

Bubble sort,  which is also known as  sinking sort, is  described as a simple sorting algorithm that repeatedly steps through the input list element by element, comparing the current element with the one after it, swapping their values if needed.

Learn more about Bubble sort at: https://brainly.com/question/29976694

#SPJ4

When you manipulate the voltage slider in the given scenarios, the following effects can be observed:

1) Setting the voltage of the battery to zero: When the voltage is set to zero, there will be no potential difference across the coil. Consequently, the current flowing through the coil will be zero, and the magnetic field generated around the coil will also be nonexistent.

2) Increasing the voltage of the battery positively and negatively: When you increase the voltage positively, the current flowing through the coil will increase as well, resulting in a stronger magnetic field around the coil. Conversely, when you increase the voltage negatively (i.e., reverse the polarity), the direction of the current flow in the coil will change, and this will cause the magnetic field around the coil to reverse its direction as well.

To learn more about magnetic field visit;

https://brainly.com/question/23096032

#SPJ11

False. An auxiliary grounding electrode alone is not sufficient as the only grounding connection for electronic equipment, even when noise on the equipment grounding circuit is a problem.

According to the National Electrical Code (NEC), grounding electrode systems are designed to provide a low-impedance path for fault current to flow to the earth, which protects equipment and people from electrical hazards. Grounding electrodes, such as grounding rods, are only one part of a complete grounding system that includes grounding conductors and bonding jumpers.The NEC requires that all electronic equipment be grounded using an equipment grounding conductor that is connected to the main grounding electrode system. The use of an auxiliary grounding electrode in addition to the main grounding electrode system is permitted, but it cannot be used as the only grounding connection for electronic equipment.

To learn more about connection click on the link below:

brainly.com/question/31494083

#SPJ11

it's worth noting that our estimate of distance traveled may not be very accurate, since it is based on assumptions and not actual measurements. In order to get a more precise measurement of space-mean speed, we would need additional information or more precise data.

To calculate the space-mean speed for Problem 5.3, we need to know the distance each car traveled during the time it was being observed in the aerial photo. Unfortunately, the photo alone does not provide us with this information. However, we do know the constant travel speed of each vehicle. To estimate the distance traveled, we could make some assumptions about the size of the race track and the length of time each car was in view in the photo. Based on these assumptions, we could estimate the distance each car traveled during that time. Once we have estimated the distance traveled, we can use the formula for space-mean speed: space-mean speed = total distance traveled / total time. We would need to add up the distances traveled by each car and divide by the total time they were observed.

Learn more about distance here

https://brainly.com/question/28551043

#SPJ11

When inspecting a post-tension installation, the inspector is responsible for checking all of the following except the initial design calculations.

During a post-tension installation inspection, the inspector typically checks for proper materials, installation techniques, and compliance with the project specifications. This may include verifying tendon placement, stressing equipment, and grouting procedures.

However, the initial design calculations, which are the responsibility of the structural engineer or designer, are not part of the inspector's responsibilities during the inspection.
The inspector focuses on ensuring that the post-tension installation is executed correctly and complies with project requirements, while the responsibility for checking the initial design calculations lies with the structural engineer or designer.

For more information on inspection kindly visit to

https://brainly.com/question/14673987

#SPJ11

A structural component that carries the load in the transverse direction to the longitudinal axis of the member is known as a beam. The three types of beams commonly used in structural engineering are:

Simply Supported Beam: A simply supported beam is supported at its ends and is free to rotate at those points. It is the most common type of beam used in construction and typically spans between two supports, such as columns or walls. Simply supported beams are subjected to bending stresses when loads are applied, and they are designed to resist bending and shear forces.

Fixed Beam: A fixed beam is supported at both ends and is restrained from rotating at those points. This means that the ends of the beam are rigidly connected to their supports, preventing any rotation. Fixed beams are designed to resist bending, shear, and torsional forces, and they are used in situations where high stability and rigidity are required, such as in building frames or bridge piers.

Cantilever Beam: A cantilever beam is supported at one end and is free to rotate at that point. The other end of the beam is unsupported and projects outward, carrying the load. Cantilever beams are commonly used in situations where one end of the beam needs to be anchored or fixed, while the other end is left unsupported, such as in balconies, canopies, or overhanging structures. Cantilever beams are designed to resist bending and shear forces, and they require careful consideration of their stability and deflection characteristics.

These three types of beams have different structural behaviors and design considerations, and their selection depends on the specific requirements of a given structural system or construction project. Proper design and analysis of beams are crucial in ensuring structural stability and safety in construction projects.

Learn more about  beam   here:

https://brainly.com/question/31324896

#SPJ11

To shut down the system immediately and send a message to logged in users to allow running processes to close gracefully, the command that can be used is "shutdown -h now".

The "-h" flag stands for halt, which means the system will shut down completely, and the "now" keyword specifies that it should happen immediately. Additionally, the command can be modified to include a message that will be displayed to all logged-in users, informing them of the impending shutdown and giving them time to save their work and close running processes. To include a message, the command can be modified to "shutdown -h now 'System is shutting down, please save your work and close all running processes gracefully'".  It is important to allow running processes to close gracefully as abruptly shutting down a system can lead to data loss or corruption.

Graceful shutdown ensures that all processes are given the opportunity to complete their tasks and save their data before the system is shut down. This helps prevent data loss and damage to the system. In addition, sending a message to users allows them to prepare for the shutdown, preventing them from losing unsaved work or leaving critical processes running that could cause issues when the system is restarted.

Learn more about  command  here: https://brainly.com/question/29627815

#SPJ11

An object's position can be determined either linearly or angularly using a PID (Position Indicator Device).

A PID is a device that has a high degree of accuracy in determining an object's position. It has a wide range of uses, including manufacturing, robotics, and aircraft. The instrument is capable of measuring both angular and linear position, and it commonly locates objects using sensors like optical or magnetic ones. In closed-loop control systems, where an object's position is continuously monitored and changed to attain a desired position, the PID is frequently utilised. In many industrial applications, it's crucial that the object be positioned precisely and consistently, and this helps to ensure that.

learn more about PID here:

https://brainly.com/question/17032153

#SPJ11

Both Technician A and Technician B are correct in their statements.

Technician A is correct because diodes are indeed used to rectify the voltage produced from an AC generator, converting it from alternating current (AC) to direct current (DC).

Technician B is also correct because a Zener diode is specifically designed to protect circuit components from voltage spikes by regulating voltage levels and allowing current to flow in the reverse direction when the voltage exceeds a specific threshold.

Technician A is correct in that diodes are commonly used to rectify the voltage produced by an AC generator, converting it from AC to DC.

This is an important step in many electrical systems, as DC voltage is required for many electronic devices to function properly.

Technician B is also correct in that a Zener diode can be used to protect circuit components from voltage spikes.

Zener diodes are designed to regulate voltage levels and maintain a constant voltage across their terminals, even when the voltage at the input terminals exceeds a certain threshold.

This can be useful in protecting other components in the circuit from damage due to voltage spikes.

In summary, both Technician A and Technician B are correct in their statement.

For similar question on AC generator.

https://brainly.com/question/24487261

#SPJ11