Answer:
Both technician A and technician B are correct.
Explanation: Vehicle manufacturers always specify the size of the tires required for a given vehiclefor optimal efficiency,this will ensure that the speedometer is accurate and the level of the vehicle is good enough to ensure the vehicle works efficiently.
It is also a known fact that an increase in a vehicle's rpm(revolution per minute) will eventually lead to increased fuel consumption which means the fuel economy of the vehicle will be reduced making the vehicle less efficient in its fuel consumption.
Determine the length of the cantilevered beam so that the maximum bending stress in the beam is equivalent to the maximum shear stress.
In this exercise we have to calculate the formula that will be able to determine the length of the cantilevered, like this:
[tex]\sigma_{max}C=\frac{M_{max}C}{I}[/tex]
So to determinated the maximum tensile and compreensive stress due to bending we can describe the formula as:
[tex]\sigma_b = \frac{MC}{I}[/tex]
Where,
[tex]\sigma_b[/tex] is the compressive stress or tensile stress[tex]M[/tex] is the B.M [tex]C[/tex] is the N.A distance[tex]I[/tex] is the moment of interiorSo making this formula for the max, we have:
[tex]\sigma_c=\frac{MC}{I} \\\sigma_T=-\sigma_c=-\frac{MC}{I}\\\sigma_{max}=M_{max}\\[/tex]
With all this information we can put the formula as:
[tex]\sigma_{max}C=\frac{M_{max}C}{I}[/tex]
See more about stress in the beam at brainly.com/question/23637191
An inventor claims to have developed a heat pump that produces a 200-kW heating effect for a 293 K heatedzone while only using 75 kW of power and a heat source at 273 K. Justify the validity of this claim.
Answer:
From the calculation, we can see that the invention's COP of 2.67 does not exceed the maximum theoretical COP of 14.65. Hence his claim is valid and could be possible.
Explanation:
Heat generated Q = 200 kW
power input W = 75 kW
Temperature of heated region [tex]T_{h}[/tex] = 293 K
Temperature of heat source [tex]T_{c}[/tex] = 273 K
For this engine,
coefficient of performance COP = Q/W = 200/75 = 2.67
The maximum theoretical COP obtainable for a heat pump is given as
COP = [tex]\frac{T_{h} }{T_{h} - T_{c} }[/tex] = [tex]\frac{293 }{293 - 273 }[/tex] = 14.65
From the calculation, we can see that the invention's COP of 2.67 does not exceed the maximum theoretical COP of 14.65. Hence his claim is valid and could be possible.
Who plays a role in the financial activities of a company?
O A. Just employees
O B. Just managers
O C. Only members of the finance and accounting department
O D. Everyone at the company, including managers and employees
Hey,
Who plays a role in the financial activities of a company?
O D. Everyone at the company, including managers and employees
Answer:
Everyone at the company, including managers and employees
Explanation:
what's the maximum shear on a 3.0 m beam carrying 10 kN/m?
Answer:
max shear = R = V = 15 kN
Explanation:
given:
load = 10 kn/m
span = 3m
max shear = R = V = wL / 2
max shear = R = V = (10 * 3) / 2
max shear = R = V = 15 kN
A series circuit contains four resistors. In the circuit, R1 is 80 , R2 is 60 , R3 is 90 , and R4 is 100 . What is the total resistance? A. 330 B. 250 C. 460 D. 70.3
The speed above which an airplane will experience structural damage when a load is applied, instead of stalling, is called the ______________ speed and varies with weight
Answer:
Maneuvering speed.
Explanation:
The speed above which an airplane will experience structural damage when a load is applied, instead of stalling, is called the maneuvering speed and varies with weight.
In aeronautical engineering, the maneuvering speed (Va) of an aircraft such as an aeroplane, helicopter, or jet is an airspeed limitation which is mainly selected by an aircraft designer.
Generally, at speeds higher or greater than the manoeuvring speed, aircraft pilots are advised not to attempt a full deflection of any flight control surface because it's capable of resulting in a damage to the structure of an aircraft.
If you're a pilot, to find the maneuvering speed of an aircraft, you should look at the flight manual of the aircraft or on the cockpit placard in the aircraft. The maneuvering speed of an aircraft is a calibrated speed and should not be exceeded by any pilot.
. A belt drive is desired to couple the motor with a mixer for processing corn syrup. The 25-hp electric motor is rated at 950 rpm and the mixer must operate as close to 250 rpm as possible. Select an appropriate belt size, commercially available sheaves, and a belt for this application. Also calculate the actual belt speed and the center distance.
Answer:
Hello the table which is part of the question is missing and below are the table values
For a 5V belt the available diameters are : 5.5, 5.8, 5.9, 6.2, 6.3, 6.6, 12.5, 13.9, 15.5, 16.1, 18.5, 20.1
Answers:
belt size = 140 in with diameter of 20.1n
actual speed of belt = 288.49 in/s
actual center distance = 49.345 in
Explanation:
Given data :
Electric motor (driver sheave) speed (w1) = 950 rpm
Driven sheave speed (w2) = 250 rpm
pick D1 ( diameter of driver sheave) = 5.8 in ( from table )
To select an appropriate belt size we apply the equation for the velocity ratio to get the diameter first
VR = [tex]\frac{w1}{w2}[/tex] = 950 / 250
also since the speed of belt would be constant then ;
Vb = w1r1 = w2r2 ------- equation 1
r = d/2
substituting the value of r into equation 1
equation 2 becomes : [tex]\frac{w1}{w2} = \frac{d2}{d1}[/tex] = VR
Appropriate belt size ( d2) can be calculated as
d2 = [tex]\frac{w1d1}{w2}[/tex] = [tex]\frac{950 * 5.8}{250}[/tex] = 22.04
From the given table the appropriate belt size would be : 20.1 because it is the closest to the calculated value
next we have to determine the belt length /size
[tex]L = 2C + \frac{\pi }{2} ( d1+d2) + \frac{(d2-d1)^2}{4C}[/tex]
inputting all the values into the above equation including the value of C as calculated below
L ≈ 140 in
Calculating the center distance
we use this equation to get the ideal center distance
[tex]d2< C_{ideal} < 3( d1 +d2)[/tex]
22.04 < c < 3 ( 5.8 + 20.1 )
22.04 < c < 77.7
the center distance is between 22.04 and 77.7 but taking an average value
ideal center distance would be ≈ 48 in
To calculate the actual center distance we use
[tex]C = \frac{B+\sqrt{B^2 - 32(d2-d1)^2} }{16}[/tex] -------- equation 3
B = [tex]4L -2\pi (d2 + d1 )[/tex]
inputting all the values into (B)
B = 140(4) - 2[tex]\pi[/tex]( 20.01 + 5.8 )
B ≈ 399.15 in
inputting all the values gotten Back to equation 3 to get the actual center distance
C = 49.345 in ( actual center distance )
Calculating the actual belt speed
w1 = 950 rpm = 99.48 rad/s
belt speed ( Vb) = w1r1 = w1 * [tex]\frac{d1}{2}[/tex]
= 99.48 * 5.8 / 2 = 288.49 in/s
Given the unity feedback system
G(s)= K(s+4)/s(s+1.2)(s+2)
Find:
a. The range of K that keeps the system stable
b. The value of K that makes the system oscillate
c. The frequency of oscillation when K is set to the value that makes the system oscillate
Answer:
A.) 0 > K > 9.6
B.) K = 9.6
C.) w = +/- 2 sqrt (3)
Explanation:
G(s)= K(s+4)/s(s+1.2)(s+2)
For a closed loop stability, we can analyse by using Routh - Horwitz analysis.
To make the pole completely imaginary, K must be equal to 9.6 Because for oscillations. Whereas, one pair of pole must lie at the imaginary axis.
Please find the attached files for the solution