Answer:
A. Z = 185.87Ω
B. I = 0.16A
C. V = 1mV
D. VL = 68.8V
E. Ф = 30.59°
Explanation:
A. The impedance of a RL circuit is given by the following formula:
[tex]Z=\sqrt{R^2+\omega^2L^2}[/tex] (1)
R: resistance of the circuit = 160-Ω
w: angular frequency = 220 rad/s
L: inductance of the circuit = 0.430H
You replace in the equation (1):
[tex]Z=\sqrt{(160\Omega)^2+(220rad/s)^2(0.430H)^2}=185.87\Omega[/tex]
The impedance of the circuit is 185.87Ω
B. The current amplitude is:
[tex]I=\frac{V}{Z}[/tex] (2)
V: voltage amplitude = 30.0V
[tex]I=\frac{30.0V}{185.87\Omega}=0.16A[/tex]
The current amplitude is 0.16A
C. The current I is the same for each component of the circuit. Then, the voltage in the resistor is:
[tex]V=\frac{I}{R}=\frac{0.16A}{160\Omega}=1*10^{-3}V=1mV[/tex] (3)
D. The voltage across the inductor is:
[tex]V_L=L\frac{dI}{dt}=L\frac{d(Icos(\omega t))}{dt}=-LIsin(\omega t)\\\\V_L=-(0.430H)(160\Omega)sin(220 t)=68.8sin(220t)\\\\V_L_{max}=68.8V[/tex]
E. The phase difference is given by:
[tex]\phi=tan^{-1}(\frac{\omega L}{R})=tan^{-1}(\frac{(220rad/s)(0.430H)}{160\Omega})\\\\\phi=30.59\°[/tex]
In an oscillating LC circuit, the total stored energy is U and the maximum current in the inductor is I. When the current in the inductor is I/2, the energy stored in the capacitor is
Answer:
The definition of that same given problem is outlined in the following section on the clarification.
Explanation:
The Q seems to be endless (hardly any R on the circuit). So energy equations to describe and forth through the inducer as well as the condenser.
Presently take a gander at the energy stored in your condensers while charging is Q.
⇒ [tex]U =\frac{Qmax^2}{C}[/tex]
So conclude C doesn't change substantially as well as,
When,
⇒ [tex]Q=\frac{Qmax}{2}[/tex]
⇒ [tex]Q^2=\frac{Qmax^2}{4}[/tex]
And therefore only half of the population power generation remains in the condenser that tends to leave this same inductor energy at 3/4 U.
A 5.0-Ω resistor and a 9.0-Ω resistor are connected in parallel. A 4.0-Ω resistor is then connected in series with this parallel combination. An ideal 6.0-V battery is then connected across the series-parallel combination of the three resistors. What is the current through (a) the 4.0-Ω resistor? (b) the 5.0-Ω resistor? (c) the 9.0-Ω resistor?
Answer:
Explanation:
The current through the resistor is 0.83 A
.
Part b
The current through resistor is 0.53 A
.
Part c
The current through resistor is 0.30 A
a ring with a clockwise current is situated with its center directly above another ring. The current in the top ring is decreasing. What is the directiong of the induced current in the bottom ring
Answer:
clockwise
Explanation:
when current flows through a ring in a clockwise direction, it produces the equivalent magnetic effect of a southern pole of a magnet on the coil.
Since the current is decreasing, there is a flux change on the lower ring; generating an induced current on the lower ring. According to Lenz law of electromagnetic induction, "the induced current will act in such a way as to oppose the motion or the action producing it". In this case, the induced current will have to be the same polarity to the polarity of the current change producing it so as to repel the two rings far enough to stop the electromagnetic induction. The induced current will then be in the clockwise direction on the lower ring.
The direction of the induced current in the bottom ring is in the clockwise direction.
The given problem is based on the concept and fundamentals of the induced current and the direction of flow of the induced current.
When current flows through a ring in a clockwise direction, it produces the equivalent magnetic effect of a southern pole of a magnet on the coil. Since the current is decreasing, there is a flux change on the lower ring; generating an induced current on the lower ring. According to Lenz law of electromagnetic induction, "the induced current will act in such a way as to oppose the motion or the action producing it". In this case, the induced current will have to be the same polarity to the polarity of the current change producing it so as to repel the two rings far enough to stop the electromagnetic induction. The induced current will then be in the clockwise direction on the lower ring.Thus, we can conclude that the direction of the induced current in the bottom ring is in the clockwise direction.
Learn more about the concept of induced current here:
https://brainly.com/question/3712635
When a nerve cell fires, charge is transferred across the cell membrane to change the cell's potential from negative to positive. For a typical nerve cell, 9.2pC of charge flows in a time of 0.52ms .What is the average current through the cell membrane?
Answer:
The average current will be "17.69 nA".
Explanation:
The given values are:
Charge,
q = 9.2 pC
Time,
t = 0.52ms
The equivalent circuit of the cell surface is provided by:
⇒ [tex]i_{avg}=\frac{charge}{t}[/tex]
Or,
⇒ [tex]i_{avg}=\frac{q}{t}[/tex]
On substituting the given values, we get
⇒ [tex]=\frac{9.2\times 10^{-12}}{0.52\times 10^{-3}}[/tex]
⇒ [tex]=17.69^{-9}[/tex]
⇒ [tex]=17.69 \ nA[/tex]
Julie is playing with a toy car and is pushing it around on the floor. The little car has a mass of 6.3 g. The car has a velocity of 2.5 m/s. What is the car's momentum?
Answer:
Momentum of the car = [tex]1.575\times 10^{-2}[/tex] kg meter per second
Explanation:
Julie is playing with a car which has mass = 6.3 g = [tex]6.3\times 10^{-3}[/tex] kg
Velocity of the car is 2.5 meter per second
Since formula to calculate the momentum of an object is,
p = mv
Where, p = momentum of the object
m = mass of the object
v = velocity of the object
By substituting these values in the formula,
p = [tex](6.3\times 10^{-3})\times 2.5[/tex]
= [tex]1.575\times 10^{-2}[/tex] Kg meter per second
Therefore, momentum of the car will be [tex]1.575\times 10^{-2}[/tex] Kg meter per second.
A helicopter rotor blade is 3.40m long from the central shaft to the rotor tip. When rotating at 550rpm what is the radial acceleration of the blade tip expressed in multiples of g?
Answer:
a = 1.15 10³ g
Explanation:
For this exercise we will use the relations of the centripetal acceleration
a = v² / r
where is the linear speed of the rotor and r is the radius of the rotor
let's use the relationships between the angular and linear variables
v = w r
let's replace
a = w² r
let's reduce the angular velocity to the SI system
w = 550 rev / min (2pi rad / 1 rev) (1 min / 60 s)
w = 57.6 rad / s
let's calculate
a = 57.6² 3.4
a = 1.13 10⁴ m / s²
To calculate this value in relation to g, let's find the related
a / g = 1.13 10⁴ / 9.8
a = 1.15 10³ g
A box with an initial speed of 15 m/s slides along a surface where the coefficient of sliding friction is 0.45. How long does it take for the block to come to rest
Answer:
t = 3.4 s
The box will come to rest in 3.4 s
Explanation:
For the block to come to rest, the friction force must become equal to the unbalanced force. Therefore:
Unbalanced Force = Frictional Force
but,
Unbalanced Force = ma
Frictional Force = μR = μW = μmg
Therefore,
ma = μmg
a = μg
where,
a = acceleration of box = ?
μ = coefficient of sliding friction = 0.45
g = 9.8 m/s²
Therefore,
a = (0.45)(9.8 m/s²)
a = -4.41 m/s² (negative sign due to deceleration)
Now, for the time to stop, we use first equation of motion:
Vf = Vi + at
where,
Vf = Final Speed = 0 m/s (since box stops at last)
Vi = Initial Speed = 15 m/s
t = time to stop = ?
Therefore,
0 m/s = 15 m/s + (-4.41 m/s²)t
(-15 m/s)/(-4.41 m/s²) = t
t = 3.4 s
The box will come to rest in 3.4 s
An object attached to a horizontal spring is oscillating back and forth along a frictionless surface. The maximum speed of the object is 1.38 m/s, and its maximum acceleration is 6.83 m/s2. How much time elapses betwen an instant when the object's speed is at a maximum and the next instant when its acceleration is at a maximum
Answer:
t = 0.31s
Explanation:
In order to calculate the time that the object takes to travel from the point with its maximum speed to the point with the maximum acceleration, you first use the following formulas, for the maximum speed and the maximum acceleration:
[tex]v_{max}=\omega A\\\\a_{max}=\omega^2A[/tex]
A: amplitude
v_max = 1.38m/s
a_max = 6.83m/s^2
w: angular frequency
From the previous equations you can obtain the angular frequency w.
You divide vmax and amax, and solve for w:
[tex]\frac{v_{max}}{a_{max}}=\frac{\omega A}{\omega^2 A}=\frac{1}{\omega}\\\\\omega=\frac{a_{max}}{v_{max}}=\frac{6.83m/s^2}{1.38m/s^2}=4.94\frac{rad}{s}[/tex]
Next, you take into account that the maximum speed is obtained when the object passes trough the equilibrium point, and the maximum acceleration for the maximum elongation, that is, the amplitude. In such a trajectory the time is T/4 being T the period.
You calculate the period by using the information about the angular frequency:
[tex]T=\frac{2\pi}{\omega}=\frac{2\pi}{4.94rad/s}=1.26s[/tex]
Then the required time is:
[tex]t=\frac{T}{4}=\frac{1.26s}{4}=0.31s[/tex]
An empty parallel plate capacitor is connected between the terminals of a 9.0-V battery and charged up. The capacitor is then disconnected from the battery, and the spacing between the capacitor plates is doubled. As a result of this change, what is the new voltage between the plates of the capacitor
Answer:
The new voltage between the plates of the capacitor is 18 V
Explanation:
The charge on parallel plate capacitor is calculated as;
q = CV
Where;
V is the battery voltage
C is the capacitance of the capacitor, calculated as;
[tex]C = \frac{\epsilon _0A}{d} \\\\q =CV = (\frac{\epsilon _0A}{d})V = \frac{\epsilon _0A V}{d}[/tex]
[tex]q = \frac{\epsilon _0A V}{d}[/tex]
where;
ε₀ is permittivity of free space
A is the area of the capacitor
d is the space between the parallel plate capacitors
If only the space between the capacitors is doubled and every other parameter is kept constant, the new voltage will be calculated as;
[tex]q = \frac{\epsilon _0A V}{d} \\\\\frac{\epsilon _0A V}{d} = \frac{\epsilon _0A V}{d} \\\\\frac{V_1}{d_1} = \frac{V_2}{d_2} \\\\V_2 = \frac{V_1d_2}{d_1} \\\\(d_2 = 2d_1)\\\\V_2 = \frac{V_1*2d_1}{d_1} \\\\(V_1 = 9V)\\\\V_2 = \frac{9*2d_1}{d_1} \\\\V_2 = 9*2\\\\V_2 = 18 \ V[/tex]
Therefore, the new voltage between the plates of the capacitor is 18 V
How does an atom of rubidium-85 become a rubidium ion with a +1 charge?
Answer:
C. The atom loses 1 electron to have a total of 36.
Explanation:
Cations have a positive charge. Cations lose electrons.
The number of electrons in a Rubidium atom is 37. If the atom loses 1 electron, then it has 36 left.
If 62.9 cm of copper wire (diameter = 1.15 mm, resistivity = 1.69 × 10-8Ω·m) is formed into a circular loop and placed perpendicular to a uniform magnetic field that is increasing at the constant rate of 8.43 mT/s, at what rate is thermal energy generated in the loop?
Answer:
The answer is "[tex]\bold{7.30 \times 10^{-6}}[/tex]"
Explanation:
length of the copper wire:
L= 62.9 cm
r is the radius of the loop then:
[tex]r=\frac{L}{2 \pi}\\[/tex]
[tex]=\frac{62.9}{2\times 3.14}\\\\=\frac{62.9}{6.28}\\\\=10.01\\[/tex]
area of the loop Is:
[tex]A_L= \pi r^2[/tex]
[tex]=100.2001\times 3.14\\\\=314.628[/tex]
change in magnetic field is:
[tex]=\frac{dB}{dt} \\\\ = 0.01\ \frac{T}{s}[/tex]
then the induced emf is: [tex]e = A_L \times \frac{dB}{dt}[/tex]
[tex]=314.628 \times 0.01\\\\=3.14\times 10^{-5}V[/tex]
resistivity of the copper wire is: [tex]\rho =[/tex] 1.69 × 10-8Ω·m
diameter d = 1.15mm
radius (r) = 0.5mm
[tex]= 0.5 \times 10^{-3} \ m[/tex]
hence the resistance of the wire is:
[tex]R=\frac{\rho L}{\pi r^2}\\[/tex]
[tex]=\frac{1.69 \times 10^{-8}(62.9)}{3.14 \times (0.5 \times 10^{-3})^2}\\\\=\frac{1.69 \times 10^{-8}(62.9)}{3.14 \times 0.5 \times 0.5 \times 10^{-6}}\\\\=\frac{1.69 \times 10^{-8}(62.9)}{3.14 \times 0.25 \times 10^{-6}}\\\\=135.41 \times 10^{-2}\\=1.35\times 10^{-4}\\[/tex]
Power:
[tex]P=\frac{e^2}{R}[/tex]
[tex]=\frac{3.14\times 10^{-5}\times 3.14\times 10^{-5}}{1.35 \times 10^{-4}}\\\\=7.30 \times 10^{-6}[/tex]
The final answer is: [tex]\boxed{7.30 \times 10^{-6} \ W}[/tex]
What is the length (in m) of a tube that has a fundamental frequency of 108 Hz and a first overtone of 216 Hz if the speed of sound is 340 m/s?
Answer:
Length of a tube = 1.574 m
Explanation:
Given:
Fundamental frequency (f1) = 108 Hz
First overtone (f2) = 216 Hz
Speed of sound (v) = 340 m/s
Find:
Length of a tube
Computation:
We know that,
f = v / λ
f = nv / 2L [n = number 1,2,3]
So,
f1 = 1(340) / 2L
f1 = 170 / L
L = 170 / 108 = 1.574 m
f2 = 2(340) / 2L
L = 340 / 216
L = 1.574 m
Copper wire of diameter 0.289 cm is used to connect a set of appliances at 120 V, which draw 1850 W of power total. The resistivity of copper is 1.68×10−8Ω⋅m.
A. What power is wasted in 26.0 m of this wire?
B. What is your answer if wire of diameter 0.417 cm is used?
Answer:
(a) The power wasted for 0.289 cm wire diameter is 15.93 W
(b) The power wasted for 0.417 cm wire diameter is 7.61 W
Explanation:
Given;
diameter of the wire, d = 0.289 cm = 0.00289 m
voltage of the wire, V = 120 V
Power drawn, P = 1850 W
The resistivity of the wire, ρ = 1.68 x 10⁻⁸ Ω⋅m
Area of the wire;
A = πd²/4
A = (π x 0.00289²) / 4
A = 6.561 x 10⁻⁶ m²
(a) At 26 m of this wire, the resistance of the is
R = ρL / A
R = (1.68 x 10⁻⁸ x 26) / 6.561 x 10⁻⁶
R = 0.067 Ω
Current in the wire is calculated as;
P = IV
I = P / V
I = 1850 / 120
I = 15.417 A
Power wasted = I²R
Power wasted = (15.417²)(0.067)
Power wasted = 15.93 W
(b) when a diameter of 0.417 cm is used instead;
d = 0.417 cm = 0.00417 m
A = πd²/4
A = (π x 0.00417²) / 4
A = 1.366 x 10⁻⁵ m²
Resistance of the wire at 26 m length of wire and 1.366 x 10⁻⁵ m² area;
R = ρL / A
R = (1.68 x 10⁻⁸ x 26) / 1.366 x 10⁻⁵
R = 0.032 Ω
Power wasted = I²R
Power wasted = (15.417²)(0.032)
Power wasted = 7.61 W
What is unique about the c-ray that is not about other rays? Note: Refer to the concave mirror video Select one: a. only ray whose angle of incidence = angle of reflection b. only ray that reflects back in the same direction it came from c. both the above statements are true d. none of the above
Answer:
b. only ray that reflects back in the same direction it came from
Explanation:
C-rays can be said to be a ray that comes from the center of the curvature. It is known that any ray that comes from the center of the curvature reflects back in the same direction it came from, this is because the line joining from the center of the curvature to any point in the mirror is perpendicular to the mirror.
Correct answer is option B.
C-ray is the only ray that reflects back in the same direction it came from.
Option A is incorrect because for other rays, angle of incidence = angle of reflection. This is not a property of c-ray.
A 750 kg car is moving at 20.0 m/s at a height of 5.0 m above the bottom of a hill when it runs out of gas. From there, the car coasts. a. Ignoring frictional forces and air resistance, what is the car’s kinetic energy and velocity at the bottom of the hill
Answer:
Explanation:
Kinetic energy at the height = 1/2 m v²
= 1/2 x 750 x 20²
= 150000 J
Its potential energy = mgh
= 750 x 9.8 x 5
=36750 J
Total energy = 186750 J
Its total kinetic energy will be equal to 186750 J , according to conservation of mechanical energy
If v be its velocity at the bottom
1/2 m v² = 186750
v = √498
= 22.31 m /s
An asteroid that has an orbital period of 3 years will have an orbital with a semi-major axis of about _____ years.
Answer:
An asteroid that has an orbital period of 3 years will have an orbital with a semi-major axis of about 2 years.
Explanation:
Given;
orbital period of 3 years, P = 3 years
To calculate the years of an orbital with a semi-major axis, we apply Kepler's third law.
Kepler's third law;
P² = a³
where;
P is the orbital period
a is the orbital semi-major axis
(3)² = a³
9 = a³
a = [tex]a = \sqrt[3]{9} \\\\a = 2.08 \ years[/tex]
Therefore, An asteroid that has an orbital period of 3 years will have an orbital with a semi-major axis of about 2 years.
A 1500 kg car drives around a flat 200-m-diameter circular track at 25 m/s. What are the magnitude and direction of the net force on the car
Answer:
9,375
Explanation:
Data provided
The mass of the car m = 1500 Kg.
The diameter of the circular track D = 200 m.
For the computation of magnitude and direction of the net force on the car first we need to find out the radius of the circular path which is shown below:-
The radius of the circular path is
[tex]R = \frac{D}{2}[/tex]
[tex]= \frac{200}{2}[/tex]
= 100 m
after the radius of the circular path we can find the magnitude of the centripetal force with the help of below formula
[tex]Force F = \frac{mv^2}{R}[/tex]
[tex]= \frac{1500\times (25)^2}{100}[/tex]
= 9,375
Therefore for computing the magnitude of the centripetal force we simply applied the above formula.
A dumbbell-shaped object is composed by two equal masses, m, connected by a rod of negligible mass and length r. If I1 is the moment of inertia of this object with respect to an axis passing through the center of the rod and perpendicular to it and I2 is the moment of inertia with respect to an axis passing through one of the masses, it follows that:
a. I1 > I2
b. I2 > I1.
c. I1 = I2.
Answer:
B: I2>I1
Explanation:
See attached file
A uniform thin rod of mass ????=3.41 kg pivots about an axis through its center and perpendicular to its length. Two small bodies, each of mass m=0.249 kg , are attached to the ends of the rod. What must the length L of the rod be so that the moment of inertia of the three-body system with respect to the described axis is ????=0.929 kg·m2 ?
Answer:
The length of the rod for the condition on the question to be met is [tex]L = 1.5077 \ m[/tex]
Explanation:
The Diagram for this question is gotten from the first uploaded image
From the question we are told that
The mass of the rod is [tex]M = 3.41 \ kg[/tex]
The mass of each small bodies is [tex]m = 0.249 \ kg[/tex]
The moment of inertia of the three-body system with respect to the described axis is [tex]I = 0.929 \ kg \cdot m^2[/tex]
The length of the rod is L
Generally the moment of inertia of this three-body system with respect to the described axis can be mathematically represented as
[tex]I = I_r + 2 I_m[/tex]
Where [tex]I_r[/tex] is the moment of inertia of the rod about the describe axis which is mathematically represented as
[tex]I_r = \frac{ML^2 }{12}[/tex]
And [tex]I_m[/tex] the moment of inertia of the two small bodies which (from the diagram can be assumed as two small spheres) can be mathematically represented as
[tex]I_m = m * [\frac{L} {2} ]^2 = m* \frac{L^2}{4}[/tex]
Thus [tex]2 * I_m = 2 * m \frac{L^2}{4} = m * \frac{L^2}{2}[/tex]
Hence
[tex]I = M * \frac{L^2}{12} + m * \frac{L^2}{2}[/tex]
=> [tex]I = [\frac{M}{12} + \frac{m}{2}] L^2[/tex]
substituting vales we have
[tex]0.929 = [\frac{3.41}{12} + \frac{0.249}{2}] L^2[/tex]
[tex]L = \sqrt{\frac{0.929}{0.40867} }[/tex]
[tex]L = 1.5077 \ m[/tex]
A lens is designed to work in the visible, near-infrared, and near-ultraviolet. The best resolution of this lens from a diffraction standpoint is
The lens is designed to work in the visible, near-infrared, and near-ultraviolet. The best resolution of this lens from a diffraction standpoint is: in the near-ultraviolet.
What is diffraction?The act of bending light around corners such that it spreads out and illuminates regions where a shadow is anticipated is known as diffraction of light. In general, since both occur simultaneously, it is challenging to distinguish between diffraction and interference. The diffraction of light is what causes the silver lining we see in the sky. A silver lining appears in the sky when the sunlight penetrates or strikes the cloud.
Longer wavelengths of light are diffracted at a greater angle than shorter ones, with the amount of diffraction being dependent on the wavelength of the light. Hence, among the light waves of the visible, near-infrared, and near-ultraviolet range, near-ultraviolet waves have the shortest wavelengths. So, The best resolution of this lens from a diffraction standpoint is in the near-ultraviolet, where diffraction is minimum.
Learn more about diffraction here:
https://brainly.com/question/11176463
#SPJ5
A 100 kg lead block is submerged in 2 meters of salt water, the density of which is 1096 kg / m3. Estimate the value of the hydrostatic pressure.
Answer:
21,920 Pascals
Explanation:
P = ρgh
P = (1096 kg/m³) (10 m/s²) (2 m)
P = 21,920 Pa
a block of wood is pulled by a horizontal string across a rough surface at a constant velocity with a force of 20N. the coefficient of kinetic friction between the surfaces is 0.3 the force of the friction is
Answer:
6 N
Explanation:
From the laws of friction
F = ¶R = 0.3 × 20 = 6 N
The force of friction opposing the block's motion is 6 N.
The given parameters;
force applied on the block, F = 20 Ncoefficient of kinetic friction = 0.3The force of friction which opposes the motion of the block is obtained by applying Newton's second law of motion.
F = ma
Fₓ = μF
Substitute the given parameters to calculate the frictional force on the object.
Fₓ = 0.3 x 20
Fₓ = 6 N
Thus, the force of friction opposing the block's motion is 6 N.
Learn more here: https://brainly.com/question/18247518
The voltage between the cathode and the screen of a television set is 30 kV. If we assume a speed of zero for an electron as it leaves the cathode, what is its speed (m/s) just before it hits the screen
Answer:
The speed is [tex]v =10.27 *10^{7} \ m/s[/tex]
Explanation:
From the question we are told that
The voltage is [tex]V = 30 kV = 30*10^{3} V[/tex]
The initial velocity of the electron is [tex]u = 0 \ m/s[/tex]
Generally according to the law of energy conservation
Electric potential Energy = Kinetic energy of the electron
So
[tex]PE = KE[/tex]
Where
[tex]KE = \frac{1}{2} * m* v^2[/tex]
Here m is the mass of the electron with a value of [tex]m = 9.11 *10^{-31} \ kg[/tex]
and
[tex]PE = e * V[/tex]
Here e is the charge on the electron with a value [tex]e = 1.60 *10^{-19} \ C[/tex]
=> [tex]e * V = \frac{1}{2} * m * v^2[/tex]
=> [tex]v = \sqrt{ \frac{2 * e * V}{m} }[/tex]
substituting values
[tex]v = \sqrt{ \frac{2 * (1.60*10^{-19}) * 30*10^{3}}{9.11 *10^{-31}} }[/tex]
[tex]v =10.27 *10^{7} \ m/s[/tex]
A commercial diffraction grating has 500 lines per mm. Part A When a student shines a 480 nm laser through this grating, how many bright spots could be seen on a screen behind the grating
Answer:
The number of bright spot is m =4
Explanation:
From the question we are told that
The number of lines is [tex]s = 500 \ lines / mm = 500 \ lines / 10^{-3} m[/tex]
The wavelength of the laser is [tex]\lambda = 480 nm = 480 *10^{-9} \ m[/tex]
Now the the slit is mathematically evaluated as
[tex]d = \frac{1}{s} = \frac{1}{500} * 10^{-3} \ m[/tex]
Generally the diffraction grating is mathematically represented as
[tex]dsin\theta = m \lambda[/tex]
Here m is the order of fringes (bright fringes) and at maximum m [tex]\theta = 90^o[/tex]
So
[tex]\frac{1}{500} * sin (90) = m * (480 *10^{-3})[/tex]
=> [tex]m = 4[/tex]
This implies that the number of bright spot is m =4
What is the one single most important reason that human impact on the planet has been so great?
Answer:
Increasing population
Explanation:
As we can see that the death rate is decreasing while at the same time the birth rate is increasing due to which it increased the population that directly impact the planet so great
Day by day the population of the villages, cities, states, the country is increasing which would create a direct human impact on the planet
Therefore the increasing population is the one and single most important reason
A rigid tank A of volume 0.6 m3 contains 5 kg air at 320K and the rigid tank B is 0.4 m3 with air at 600 kPa, 360 K. They are connected to a piston cylinder initially empty with closed valves. The pressure in the cylinder should be 800 kPa to float the piston. Now the valves are slowly opened and the entire process is adiabatic. The internal energy of the mixture at final state is:_____.
a. 229 k/kg.
b. 238 kJ/kg
c. 257 kg
d. cannot be determined.
Answer:
the internal energy of the mixture at final state = 238kJ/kg
Explanation:
Given
V= 0.6m³
m=5kg
R=0.287kJ/kg.K
T=320 K
from ideal gas equation
PV = nRT
where P is pressure, V is volume, n is number of mole, R is ideal gas constant , T is the temperature.
Recall, mole = mass/molar mass
attached is calculation of the question.
Which of the following changes will increase the frequency of the lowest frequency standing sound wave on a stretching string?Choose all that apply.A. Replacing the string with a thicker stringB. Plucking the string harderC. Doubling the length of the string
Answer:
A, C
Explanation:
Since the frequency is inversely proportional to the length of a string, then I want to increase the frequency of the lowest
A. Replacing the string with a thicker string.
Thicker strings have more density. The more density the string has, the lower the sound.
Mathematically, we can see the proportionality (direct and inverse) by looking at those formulas for Frequency and Speed, when combined:
For:
[tex]f=\frac{v}{\lambda}[/tex]
[tex]f=\frac{v}{\lambda}*\sqrt{\frac{T}{D} }[/tex]
See above, how density (D) and [tex](\lambda)[/tex] wave length are inversely proportional.
C. Doubling the length of the string.
Because the length of the string is inversely proportional to the frequency.
The longer the string, the lower the frequency.
So, if we double string, we'll hear lower sounds in any string instrument
--
In short, for A, and C We can justify both since length and density are inversely proportional to the Frequency, we need longer or thicker string.
Five identical cylinders are each acted on by forces of equal magnitude. Which force exerts the biggest torque about the central axes of the cylinders
Answer:
From the image, the force as shown in option A will exert the biggest torque on the cylinder about its central axes.
Explanation:
The image is shown below.
Torque is the product of a force about the center of rotation of a body, and the radius through which the force acts. For a given case such as this, in which the cylinders are identical, and the forces are of equal magnitude, the torque at the maximum radius away from the center will exert the maximum torque. Also, the direction of the force also matters. To generate the maximum torque, the force must be directed tangentially away from the circle formed by the radius through which the force acts away from the center. Option A satisfies both condition and hence will exert the most torque on the cylinder.
Wind erosion can be reduced by _____.
Find acceleration. Will give brainliest!
Answer:
16200 km/s
270 km/min
4.5 km/h
Explanation:
Acceleration Formula: Average Acceleration = Δv/Δt (change in velocity over change in time)
Simply plug in our known variables and solve:
a = (45.0 - 0)/10
a = 45.0/10
a = 4.5 km/h
Answer:
[tex]\boxed{\mathrm{4.5 \: kmph/s \: or \: 1.25 \: m/s^2 }}[/tex]
Explanation:
[tex]\displaystyle \mathrm{acceleration = \frac{change \: in \: velocity}{time \: taken}}[/tex]
[tex]\displaystyle \mathrm{a = \frac{v - u}{t}}[/tex]
[tex]\displaystyle \mathrm{v=final \: velocity}\\\displaystyle \mathrm{u=initial \: velocity}[/tex]
[tex]\displaystyle \mathrm{a = \frac{45- 0}{10}}[/tex]
[tex]\displaystyle \mathrm{a = \frac{45}{10}}[/tex]
[tex]\displaystyle \mathrm{a = 4.5}[/tex]
[tex]\mathrm{4.5 \: kmph/s = 1.25 \: m/s^2 }[/tex]