A car of mass 1200 kg accelerates from 5m/s to 15 m/s the force of the engine acts on the car is 500n over what distance did the force act

The charge q on the capacitor immediately after the switch closed is 0.00 coulombs (C) to two significant figures, with the appropriate units included.

To determine the charge q on the capacitor immediately after the switch is closed, we must first consider the behavior of the capacitor during the charging process. When the switch is closed, the capacitor begins to charge up from an initial state of zero charge. During this charging process, the current flows through the circuit and the voltage across the capacitor gradually increases until it reaches the maximum voltage supplied by the source.

The charge q on the capacitor at any time during this process can be found using the formula q = CV, where C is the capacitance of the capacitor in Farads (F) and V is the voltage across the capacitor in volts (V). Immediately after the switch is closed, however, the capacitor has not yet had any time to charge. Therefore, the voltage across the capacitor is still zero. Applying the formula, we find that q = CV = C(0V) = 0. So, the charge q on the capacitor immediately after the switch is closed is 0.00 coulombs (C) to two significant figures, with the appropriate units included.

Learn more about capacitor at:

https://brainly.com/question/30889004

#SPJ11

Ice skaters get spinning rapidly by using the conservation of energy principle. They do not violate the conservation of energy.

When ice skaters begin their spin, they have their arms and one leg extended outwards. This extended position increases their moment of inertia, or the measure of how difficult it is to change the object's rotational motion. As they pull their arms and leg closer to their body, their moment of inertia decreases. According to the conservation of angular momentum, when the moment of inertia decreases, the angular velocity (or spinning speed) must increase to keep the angular momentum constant. This increase in angular velocity causes ice skaters to spin rapidly.
So, ice skaters gain their spinning energy by changing their body position, not by adding external energy, and they do not violate the conservation of energy.

Learn more about the conservation of energy here: https://brainly.com/question/20535153

#SPJ11

The driver reaction times of oncoming vehicles would need to be shortened to an average of approximately 1.018 seconds for the probability of an accident to equal 0.20.

Practice Problem 5.2 refers to a situation where a driver needs to react within 1 second to avoid an accident, but the actual reaction time is normally distributed with a mean of 1.25 seconds and a standard deviation of 0.2 seconds.

To calculate the required shortening of driver reaction times for the probability of an accident to equal 0.20, we can use the inverse normal distribution function.

First, we need to find the z-score corresponding to a probability of 0.20. Using a standard normal distribution table or calculator, we find that the z-score is approximately -0.84.

Next, we can use the formula for converting a normally distributed variable to a standard normal variable:

z = (x - μ) / σ

where z is the z-score, x is the value of the variable we want to convert, μ is the mean, and σ is the standard deviation.

We want to find the new mean reaction time (x) that corresponds to a z-score of -0.84 and keeps the probability of an accident at 0.20:

-0.84 = (x - 1.25) / 0.2

Solving for x, we get:

x = -0.84 * 0.2 + 1.25 = 1.018 seconds

Therefore, the driver reaction times of oncoming vehicles would need to be shortened to an average of approximately 1.018 seconds for the probability of an accident to equal 0.20.

Learn more on reaction time here https://brainly.com/question/6167212

#SPJ1

Consider the conditions in Practice Problem 5.2. How short would the driver reaction times of oncoming vehicles have to be for the probability of an accident to equal 0.20?

To find the distance between the object and image produced by a converging lens with a 35.5 cm focal length when the object is 45 cm from the lens, you can use the lens formula:

1/f = 1/do + 1/di

Where:
f = focal length (35.5 cm)
do = object distance (45 cm)
di = image distance

Step 1: Plug in the values for f and do:
1/35.5 = 1/45 + 1/di

Step 2: Subtract 1/45 from both sides:
1/35.5 - 1/45 = 1/di

Step 3: Find a common denominator and subtract:
(45 - 35.5)/(35.5 * 45) = 1/di
9.5/(35.5 * 45) = 1/di

Step 4: Take the reciprocal of both sides:
di = (35.5 * 45)/9.5

Step 5: Calculate di:
di ≈ 168.42 cm

So, the object and image produced by the converging lens with a 35.5 cm focal length when the object is 45 cm from the lens are approximately 168.42 cm apart.

To know more about lens formula:

https://brainly.com/question/30241648

#SPJ11

The law of conservation of mass states that the mass in an isolated system can neither be created nor be destroyed but can be transformed from one form to another.

In the conversion of any form of energy, it obeys the law of conservation. That is to say that energy is not lost but can be converted from one form to another.

A form of energy can transform to another form when there is a change in its state.

For example, light energy in bulbs is being converted to heat energy with the bulb is lit.

Learn more about energy here:

https://brainly.com/question/25959744

#SPJ1

The results of this experiment do support my hypothesis that the tennis ball would experience the highest energy loss due to its larger mass and larger surface area.

Hypothesis is a statement or a theory that is used as a starting point for further investigation. It is an educated guess or a prediction about the relationship between two or more variables. Hypothesis is used in scientific experiments to test possible explanations and predictions of natural phenomena. Hypothesis testing involves gathering data to test the hypothesis and then analyzing the results to determine if the data supports or disproves the hypothesis. If the data does not support the hypothesis, then the hypothesis is rejected and a new hypothesis must be formed.

The results showed that the tennis ball had the highest average energy loss out of the three balls tested at 42.2%. This was followed by the golf ball at 36.3%, and the ping pong ball at the lowest average energy loss of 33.9%.
Overall, this experiment was successful in that it demonstrated that the larger mass and surface area of the tennis ball do result in a higher energy loss compared to the other two balls. This experiment thus supports the hypothesis that heavier, larger balls experience more energy loss due to their size and mass.

To learn more about hypothesis
https://brainly.com/question/654258
#SPJ9

The principle of mass action states that the amount of an ion adsorbed onto the surface of soil colloids is proportional to its concentration in the soil solution.

Soil colloids are tiny, negatively charged particles found in soil that have the ability to attract and hold positively charged ions (cations) through a process called cation exchange.

Cation exchange occurs when a positively charged ion in the soil solution (such as Ca2+, Mg2+, or K+) replaces a cation that is already adsorbed onto a soil colloid. This process is driven by the principle of mass action.

The more of a particular cation that is present in the soil solution, the more likely it is to come into contact with a soil colloid and be adsorbed.

As the concentration of a particular cation in the soil solution increases, the number of adsorption sites on soil colloids occupied by that cation also increases.

Therefore, in mass action, the greater the number of an ion in the soil, the more exchange sites it will occupy.

Overall, the principle of mass action governs the adsorption of ions onto soil colloids, with the concentration of an ion in the soil solution playing a key role in determining its adsorption capacity.

To know more about mass action :

https://brainly.com/question/4172647

#SPJ11

The new velocity of the boat after 33.5 s is 25.23 m/s.

To solve this problem, we can use the concept of relative velocity. Let's consider the initial velocity of the boat as v_b and the velocity of the river current as v_c.

The boat is initially moving with a velocity v_b = 3.35 m/s. When the river current accelerates it perpendicular to its initial direction of motion, the boat experiences a change in velocity given by:

Δv = v_c * Δt

where Δt is the time for which the boat is accelerated by the current. The direction of Δv is perpendicular to both v_b and v_c, and it is given by the right-hand rule.

After the boat is accelerated by the current for a time of 33.5 s, its new velocity v_f is the vector sum of its initial velocity and the change in velocity it experienced due to the current:

v_f = v_b + Δv

To find the magnitude of v_f, we need to use the Pythagorean theorem:

|v_f| = √(v_[tex]b^2[/tex] + Δ[tex]v^2[/tex])

Substituting the given values, we get:

Δv = v_c * Δt = 0.750 [tex]m/s^2[/tex] * 33.5 s = 25.125 m/s

v_f = √(3.35 [tex]m/s)^2[/tex] + (25.125 [tex]m/s)^2[/tex] = 25.23 m/s

Therefore, the new velocity of the boat after 33.5 s is 25.23 m/s.

Learn more about new velocity

https://brainly.com/question/31041614

#SPJ4

When linked across a 20-volt battery, a length of 5.56 metres of wire is required to provide 48 watts of electricity.

We may utilise the power in a resistor formula, which is:

[tex]P = V^2 / R[/tex]

where P denotes power, V denotes voltage, and R denotes resistance.

This formula can be rearranged to account for resistance:

[tex]R = V^2 / P[/tex]

We also know that the resistance of a wire may be computed using the formula: resistivity (), length (L), and cross-sectional area (A).

R = ρL / A

We may calculate the needed length of wire by combining these two equations:

ρL / A = [tex]V^2 / P[/tex]

L = A[tex]V^2[/tex] / (P ρ)

Plugging in the given values, we get:

L = (4.0 x [tex]10^-6 m^2[/tex]) ([tex]20 V)^2[/tex]/ (48 W) (3.0 x [tex]10^8[/tex] Ω·m)

L = 5.56 m

As a result, a wire length of 5.56 metres is required to generate 48 watts of electricity when linked across a 20-volt battery.

Therefore, the length of wire required is 1.11 km.

Learn more about length

https://brainly.com/question/30100801

#SPJ4

The acceleration of Mass A is 3.2 m/s². Option B

we can find the acceleration of Mass A using the following kinematic equation:

v = u + at

where:

v = final velocity (2.56 m/s)

u = initial velocity (0 m/s, since Mass A starts from rest)

a = acceleration (which we need to find)

t = time (0.80 seconds)

Rearranging the equation to solve for acceleration, we get:

a = (v - u) / t

Now we can plug in the values:

a = (2.56 - 0) / 0.80

a = 2.56 / 0.80

a = 3.2 m/s²

Find more exercises on acceleration;

https://brainly.com/question/12550364

#SPJ1

The spring can produce 0.00585 kJ of work when compressed 3 cm from its unloaded length.

To calculate the work done by a spring, we can use the formula:

W = (1/2) k [tex]x^2[/tex]

where W is the work done by the spring, k is the spring constant, and x is the displacement of the spring from its equilibrium position.

In this case, the spring constant is given as 13 kN/cm, which is equivalent to 130 N/cm or 13,000 N/m (since 1 kN = 1000 N). The displacement of the spring from its unloaded length is 3 cm.

So, the work done by the spring is:

W = (1/2) k [tex]x^2[/tex]

W = (1/2) (13,000 N/m) (0.03 m[tex])^2[/tex]

W = 5.85 J

To convert joules to kilojoules, we can divide the answer by 1000:

W = 5.85 J / 1000

W = 0.00585 kJ

Therefore, the spring can produce 0.00585 kJ of work when compressed 3 cm from its unloaded length.

Learn more about  equilibrium position.

https://brainly.com/question/29409724

#SPJ4

If a red giant appears the same brightness as a red main sequence star, it is most likely that the red giant is further away.

Here's a step-by-step explanation:

1) Red giants and red main sequence stars are both types of stars that are similar in color, but they have different sizes and luminosities.

2) Red giants are much larger and more luminous than red main sequence stars. They are formed when a star like the sun runs out of fuel and begins to expand and cool.

3)Red main sequence stars, on the other hand, are smaller and less luminous than red giants. They are stars that are still burning hydrogen fuel in their cores.

4) The apparent brightness of a star depends on both its intrinsic luminosity and its distance from Earth. The farther away a star is, the dimmer it appears to us on Earth.

5) If a red giant appears the same brightness as a red main sequence star, this means that the red giant must be much farther away from Earth than the red main sequence star.

6) This is because the red giant is intrinsically much more luminous than the red main sequence star. If both stars were at the same distance from Earth, the red giant would appear much brighter than the red main sequence star.

7) However, since the red giant appears the same brightness as the red main sequence star, this means that the red giant must be much farther away from Earth and therefore appears dimmer.

Overall, by comparing the apparent brightness of a red giant and a red main sequence star, we can determine which star is farther away.

If the red giant appears the same brightness as the red main sequence star, then the red giant is likely to be much farther away.

To know more about fusion reactions :

https://brainly.com/question/4837991

#SPJ11

The combination of high elevation and high latitude generally results in the coldest temperatures.

option D.

Elevation refers to the height of a location above sea level, and latitude refers to the distance of a location from the equator. In general, higher elevations are colder due to the decrease in atmospheric pressure, which leads to lower temperatures. Similarly, higher latitudes are colder because they receive less direct sunlight and are farther away from the equator.

When both high elevation and high latitude are combined, the temperature tends to be the coldest. This is because high elevation areas are often located at higher latitudes, such as in mountainous regions near the poles, where the combination of lower temperatures due to elevation and lower temperatures due to latitude results in even colder temperatures.

Learn more about climate factors here: https://brainly.com/question/6691687

#SPJ1

The maximum acceleration when the truck is towing a bus of twice its own mass remains the same, which is 3.0 m/s².

Newton's second law states that the force acting on an object is equal to the mass of the object multiplied by its acceleration (F = m * a).

In this case, the tow-truck's maximum acceleration without towing the bus is 3.0 m/s². Let's denote the mass of the truck as 'm'.

When the truck is towing the bus, the total mass becomes the mass of the truck plus the mass of the bus, which is twice the mass of the truck. So, the total mass is m + 2m = 3m.

To find the maximum acceleration when towing the bus, we need to consider that the force remains the same (since the truck's engine capability doesn't change).

Therefore, we can set up the following equation using Newton's second law:

F = m * a = 3m * a_new

Now, we need to solve for the new acceleration, a_new.

We can divide both sides of the equation by 3m:

a = a_new

Since the initial acceleration, a, is 3.0 m/s², the maximum acceleration when the truck is towing a bus of twice its own mass remains the same, which is 3.0 m/s².

For more information on acceleration and mass refer to https://brainly.in/question/789316

#SPJ11

The minimum volume of the slab must be 0.007 L for the woman to stand on it without getting her feet wet.

We can solve this problem using the formula:

V = m/ρ

where V is the volume of the slab, m is the mass of the woman, and ρ is the density of water.

Assuming that the woman's feet exert a pressure of 1 atm on the water, the pressure at the bottom of the slab must be greater than 1 atm to support her weight without breaking the surface of the water. Using the formula for pressure:

P = ρgh

where P is the pressure, ρ is the density of water, g is the acceleration due to gravity, and h is the depth of the slab beneath the surface of the water. Setting P equal to 1 atm, we can solve for h:

1 atm = ρgh

h = 1 atm/(ρg)

Substituting in the values for ρ and g, we get:

h = 1 atm/(1000 kg/m³ * 9.81 m/s²) = 0.00010197 m

The minimum depth of the slab must be greater than this value to prevent the woman's feet from getting wet. Assuming that the slab is rectangular with a length and width equal to the average shoe size of a woman (about 0.26 m), we can solve for the volume:

V = lwh = 0.26 m * 0.26 m * 0.00010197 m = 0.000006769 m³

Rounding to one significant figure and converting to liters, the minimum volume of the slab is:

V = 0.007 L

Therefore, the minimum volume of the slab must be 0.007 L for the woman to stand on it without getting her feet wet.

Learn more about minimum volume

https://brainly.com/question/29591830

#SPJ4

The overall speed of the rock when it hits the ground is 24.4 m/s.

We can solve this problem using kinematic equations of motion. Since the rock is thrown horizontally, its initial vertical velocity is zero.

Let's use the following kinematic equation to find the final velocity of the rock (v):

v² = u² + 2as

where u is the initial velocity (in this case, u = 0), a is the acceleration due to gravity (-9.81 m/s²), and s is the vertical distance the rock falls (12.4 m). Solving for v, we get:

v = sqrt(2as) = sqrt(2 x (-9.81 m/s²) x 12.4 m) = 17.26 m/s

Now that we have found the final vertical velocity, we can use it to find the time it takes for the rock to fall to the ground.

The time (t) can be found using the following kinematic equation:

s = ut + (1/2)at²

where s is the horizontal distance the rock travels (17.8 m), u is the horizontal velocity of the rock (which is constant), and a is the horizontal acceleration (which is zero). Since the initial horizontal velocity is equal to the final horizontal velocity, we can use the following equation to find u:

v = u

u = v = 17.26 m/s

Now we can plug in the known values to find t:

17.8 m = 17.26 m/s x t

t = 1.03 s

Finally, we can use the horizontal distance and time to find the horizontal velocity (v_h) using the equation:

v_h = s/t = 17.8 m / 1.03 s = 17.28 m/s

Therefore, the overall speed of the rock when it hits the ground is the vector sum of the horizontal and vertical velocities:

v_overall = sqrt(v_h² + v²) = sqrt((17.28 m/s)² + (17.26 m/s)²) = 24.4 m/s

So the overall speed of the rock when it hits the ground is 24.4 m/s.

To know more about vertical velocity, visit:

https://brainly.com/question/11679227

#SPJ1

High beams cause blindness while driving. Look right, and follow the white line till the vehicle passes to see the road.

When a vehicle coming toward you has its high beams on, the bright light can cause temporary blindness and make it hard to see the road ahead. This is because the bright light scatters within the eye, causing the pupil to contract and reducing the amount of light entering the eye. To avoid this, it is recommended to look towards the right edge of the road and use the white line as a guide until the vehicle passes. This will prevent temporary blindness and allow you to see the road ahead more clearly.

Learn more about driving

brainly.com/question/25351775

#SPJ11

The solid hemisphere exerts a pressure of 17,350 Pascals on the surface.

To find the pressure exerted by the solid hemisphere, we need to consider the weight of the object and the surface area in contact with the surface. The weight of the solid hemisphere is equal to its mass times the acceleration due to gravity, which is 10 kg x 9.81 m/s^2 = 98.1 N.

The surface area in contact with the surface is the curved surface area of the hemisphere, which is half the surface area of a sphere with radius 30 mm. Using the formula for the surface area of a sphere, we get:

Surface area = 2πr^2 = 2π(30 mm)^2 = 5,655.6 mm^2

To convert this to square meters, we divide by 1,000,000, which gives us 0.0056556 m^2.

Finally, we can calculate the pressure exerted by the solid hemisphere using the formula:

Pressure = Weight / Surface area = 98.1 N / 0.0056556 m^2 = 17,350 Pa

To learn more about : hemisphere

https://brainly.com/question/29282727

#SPJ11

The number of field lines passing perpendicularly through the plate is directly proportional to the magnitude of the electric field.

The relationship between the number of electric field lines and the magnitude of the electric field.The number of field lines passing perpendicularly through a given area is proportional to the electric field's magnitude. In your case, 10 field lines represent the initial electric field (E1) magnitude.You want to depict a field with twice the magnitude (E2 = 2 * E1). Since the number of field lines is proportional to the field magnitude, you need to double the number of field lines to represent the increased magnitude.

Therefore, if a representation of an electric field shows 10 field lines perpendicular to a square plate, to depict a field with twice the magnitude, there should be 20 field lines passing perpendicularly through the plate.
So, to depict an electric field with twice the magnitude, 20 field lines (2 * 10) should pass perpendicularly through the square plate.

For more such questions on electric field , Visit:

https://brainly.com/question/14372859

#SPJ11

When switch S is closed, the circuit is complete, and current flows from the battery through the switch, bulb A, bulb B, and back to the battery. So, the correct answer is : 3.

Both bulbs receive the same current because they are connected in series. However, when the switch S is opened, the circuit is no longer complete, and the current stops flowing through the circuit. This is because the circuit will become incomplete, and no current will flow through the circuit. As a result, the bulb will not receive any electric charge, and its brightness will decrease. As a result, the bulb B receives no current and its brightness decreases to zero. Therefore, the correct answer is 3.

To know more about electric charge, here

brainly.com/question/9194793

#SPJ4

The capacitance of the second parallel plate capacitor is 2c0 which is twice that of the first capacitor.

The capacitance of a parallel plate capacitor is given by the formula C = εA/d, where C is the capacitance, ε is the permittivity of the material between the plates, A is the area of each plate, and d is the separation between the plates.

If the second capacitor has plates with twice the cross sectional area, this means that A is multiplied by 2. Similarly, if the separation is twice as much, then d is also multiplied by 2.

Therefore, the capacitance of the second capacitor is:

C = ε(2A)/(2d)

C = (εA/d) x 2

C = 2c0

So the capacitance of the second parallel plate capacitor is twice that of the first capacitor.

More on capacitance: https://brainly.com/question/17176550

#SPJ11

There are three principal rays that can be identified in a ray diagram: the ray parallel to the axis, the ray passing through the focal point and parallel to the axis, and the ray passing through the center of curvature.

The first principal ray is a ray that is parallel to the optical axis and passes through the lens. This ray will refract through the lens and pass through the focal point on the opposite side. To sketch this ray, draw a straight line that is parallel to the optical axis and intersects the lens. Then, draw the refracted ray that passes through the focal point on the opposite side.

The second principal ray is a ray that passes through the focal point on one side of the lens and then emerges from the lens parallel to the optical axis. To sketch this ray, draw a straight line that passes through the focal point on one side of the lens and intersects the lens. Then, draw the refracted ray that emerges from the lens parallel to the optical axis.

The third principal ray is a ray that passes through the center of curvature on one side of the lens and is reflected back along the same path. To sketch this ray, draw a straight line that passes through the center of curvature on one side of the lens and intersects the lens. Then, draw the reflected ray that passes back along the same path.

To learn more about ray diagram

https://brainly.com/question/14841376

#SPJ4

The speed of sound refers to the rate at which sound waves propagate or travel through a medium, such as air, water, or solid materials. The speed of sound depends on the properties of the medium, such as its density, temperature, and elasticity. In general, sound travels faster in denser, more elastic mediums, and at higher temperatures.

To find the speed of sound in air based on the time it takes to hear an echo from a canyon wall that is 569.71 meters away and takes 2.95 seconds, follow these steps:

The speed of sound in air is approximately 386.24 meters per second, given it takes 2.95 seconds to hear an echo from a canyon wall that is 569.71 meters away.

To learn more about the Speed of Sound. Please Visit:

https://brainly.com/question/28885244

#SPJ11

The first step to solving this problem is to calculate the net force acting on the cart. To do this, we need to use Newton's second law, which states that the net force is equal to the mass of the object multiplied by its acceleration. So, in this case, the net force on the cart is:

Net force = (55 kg)(2.0 m/s^2) = 110 N

Next, we need to determine the force of friction acting on the cart. We know that it is acting in the opposite direction to the applied force, so it is equal in magnitude to the net force but in the opposite direction. Therefore, the force of friction is:

Force of friction = -110 N

Finally, we can use the formula for work, which is:

Work = force x distance x cos(theta)

where theta is the angle between the force and the direction of motion. In this case, the force of friction is acting opposite to the direction of motion, so theta is 180 degrees and cos(theta) is -1.

The distance traveled by the cart is 10 m, so we can plug in the values and get:

Work = (-110 N)(10 m)(-1) = 1100 J

Therefore, the work done by the force of friction as it acts to impede the motion of the cart is 1100 J.

To know more about Newton's second law :

https://brainly.com/question/13447525

#SPJ11

The worries that critics have regarding genetically engineered crops in Africa include potential impacts on trade, dependency on foreign technology, and concerns about compatibility with local farming practices.

a. The significant impact the genetically engineered crops could have on trade in the region: Genetically engineered crops could potentially have a significant impact on trade in the region as they could flood the market, thereby disrupting existing farming systems and potentially leading to the displacement of small-scale farmers.

b. Dependency on foreign private sector businesses for technology needs: Critics have expressed concerns about the dependency of African countries on foreign private sector businesses for technology needs related to genetically engineered crops.

c. The concern over how compatible the genetically engineered crops will be with local farming standards: Critics are also concerned about the compatibility of genetically engineered crops with local farming standards and practices, as well as their potential impact on the environment and human health.

Learn more about potential impact

https://brainly.com/question/13937214

#SPJ4

Critics of genetically engineered crops in Africa have several concerns, including The potential impact these crops may have on regional trade, as they could affect export markets and trading relationships.

A growing dependency on foreign private sector businesses for technology needs might lead to a loss of control over agricultural resources and practices. Compatibility issues with local farming standards, as genetically engineered crops, may not align with traditional methods or environmental considerations, potentially disrupting the local agricultural systems. Engineered refers to something that has been intentionally designed, constructed, or modified using scientific principles and specialized knowledge to achieve a specific function or purpose. The term is often used to describe products, systems, or structures that require a high degree of precision, reliability, and efficiency. Examples of engineered products include aircraft, automobiles, bridges, computers, and medical devices. Engineers are professionals who apply their scientific and technical expertise to design and develop these products, as well as to solve complex problems in various fields such as civil, mechanical, electrical, and aerospace engineering. Engineered products and solutions play a critical role in modern society, improving our quality of life and driving innovation and economic growth.

Learn more about Engineered here:

https://brainly.com/question/31219711

#SPJ11

Having an exterior diameter of 3.50 cm and an inside diameter of 2.50 cm, a hollow cylindrical copper pipe measures 0.71 m in length. The mass of the copper pipe is closest to 6.72 kg.

To find the mass of the copper pipe, we need to first calculate its volume, which can be obtained by subtracting the volume of the hollow center from the volume of the outer cylinder.

The outer cylinder's volume can be calculated as:

[tex]$V_{outer} = \pi r_{outer}^2h$[/tex]

where r_outer is the outer radius, h is the height, and π is the mathematical constant pi.

Similarly, the inner cylinder's volume can be calculated as:

[tex]$V_{inner} = \pi r_{inner}^2h$[/tex]

where r_inner is the inner radius.

Therefore, the volume of the hollow center can be found by subtracting V_inner from V_outer:

V_hollow = V_outer - V_inner

[tex]$V_{outer} = \pi(r_{outer}^2 - r_{inner}^2)h$[/tex]

Substituting the given values, we get:

[tex]$V_{hollow} = \pi(0.0175^2 - 0.0125^2) \times 0.71$[/tex]

= 0.00074962 m^3

The mass of the copper pipe can be found by multiplying its volume by its density:

mass = density × volume

[tex]$V = 8.96 \text{ g/cm}^3 \times 749.62 \text{ cm}^3$[/tex]

= 6716.23 g

≈ 6.72 kg (rounded to two decimal places)

To learn more about copper pipe

https://brainly.com/question/27813166

#SPJ4

The average force exerted by the club on the ball is 838,400 N. Force can be characterized by its magnitude, direction, and point of application.

It can be a push or pull, and it can cause an object to start moving, stop moving, or change its direction of motion.

Force is indeed a physical factor that alters or has the potential to alter an object's state at rest or motion as well as its shape. Newton is the SI unit of force.

Finally, the average force exerted by the club on the ball is:

F = I / t = (1676.8 N·s) / (0.0020 s) = 838,400 N

To know more about force visit :

brainly.com/question/13191643

#SPJ1

Answer:

The solute and solvent have distinct chemical characteristics.

Explanation:

The solute and solvent could not have been mixed at the current temperature. The solute and solvent have distinct chemical characteristics. There was more pressure. The mixture was fully saturated.

Hope this helped :)

Answer: The fact that the solute does not mix with the solvent even after boiling and stirring repeatedly could be due to various reasons:

Insolubility: The solute may be insoluble in the solvent, meaning it cannot dissolve in it.  This could be because the solute particles are too large or have a different molecular structure compared to the solvent. For example, oil and water do not mix because oil is non-polar while water is polar.

Immiscibility: The solute and solvent may be immiscible, which means they cannot form a homogeneous mixture.  Immiscibility occurs when there is a significant difference in polarity or density between the solute and solvent.  An example of immiscible substances is oil and water, where they form separate layers instead of mixing.

Saturation: The solvent may already be saturated with the solute. Saturation occurs when the solvent can no longer dissolve any more of the solute at a given temperature. Further boiling and stirring would not result in any additional mixing.

Chemical reaction: There might be a chemical reaction occurring between the solute and solvent, leading to the formation of a new substance or a precipitate.  This can prevent the solute from dissolving completely in the solvent.

To determine the specific reason why the solute is not mixing with the solvent, it would be helpful to know the nature of the solute and solvent, as well as any other conditions or factors involved in the process.

Learn more about solutions here: https://brainly.com/question/11985826.

Sensory afferents are nerve fibers that carry sensory information from the periphery (e.g. skin, muscles, organs) to the central nervous system (CNS), where it is processed and interpreted.

These sensory afferents can be classified based on their diameter, myelination status, and the type of sensory information they transmit.

Myelination is the process by which a fatty coating called myelin is wrapped around nerve fibers.

Myelin acts as an insulator, allowing electrical impulses to travel more quickly and efficiently along the nerve fiber.

A-delta fibers and C fibers are small-diameter sensory afferents that are not myelinated, or are only thinly myelinated.

These fibers are responsible for transmitting information related to pain sensation, including noxious stimuli (e.g. tissue damage, inflammation).

A-delta fibers are typically associated with sharp, acute pain, while C fibers are associated with dull ,aching pain.

A-beta fibers, on the other hand, are large-diameter, myelinated sensory afferents that are responsible for transmitting information related to touch and pressure sensation.

These fibers are found in high numbers in the skin, joints, and muscles, and are responsible for detecting gentle pressure, vibration, and fine touch.

Therefore, the correct answer to the question is d. a-beta fibers, as they make up more than half of all sensory afferents in the body.

It is important to note that while a-delta and C fibers are responsible for transmitting pain sensation, they make up a smaller proportion of sensory afferents in the body compared to a-beta fibers.

To know more about central nervous system :

https://brainly.com/question/29974261

#SPJ11