To find the current flow in a series circuit with a total resistance of 180 ω and a total voltage of 120 V, we can use Ohm's law,(Ohm’s law states the relationship between electric current and potential difference. The current that flows through most conductors is directly proportional to the voltage applied to it. Georg Simon Ohm, a German physicist was the first to verify Ohm’s law experimentally.)
which states that current (I) equals voltage (V) divided by resistance (R), or
I = V/R. Therefore, the current flow in this circuit would be:
I = 120V/180Ohm
I = 0.67 amperes (A)
So, the current flow in this series circuit is 0.67 A.
To know more about Ohm's law, please click:
brainly.com/question/1247379
#SPJ11
Please help fast I don’t understand
The pickup truck with changing velocity can accelerate faster than the other pickup trucks.
option A.
What causes a change in velocity of a pickup truck?
A change in velocity of a pickup truck can be caused by several factors, including:
Acceleration: Acceleration is the rate of change of velocity over time, and it can result in an increase in velocity.
External forces: Other external forces, such as air resistance or friction from the road surface, can also cause a change in velocity of a pickup truck.
It's important to note that according to Newton's first law of motion, an object will maintain its velocity unless acted upon by an external force.
Therefore, any change in velocity of a pickup truck must be caused by the application of an external force.
Learn more about acceleration here: https://brainly.com/question/14344386
#SPJ1
A student is going to the office. He starts out from the classroom and walks 20 m North then stops to
talk. Then he starts for the office again and walks 30 m North, but stops again to talk. Then he walks 10 m
North and finally makes it to the office.
Find the difference in electric potential ΔV=VB−VA, between the points A and B.
The electric field does 0.052 J of work as you move a +5.7- μC charge from A and B
If the electric field moves the charge from A to B by doing 0.052 J of work, we must determine the potential difference between a and B. That much is clear. The voltage differential is 9122.8 volts as a result.
How do you calculate the difference in electric potential between two points?Moving a +5.7-C charge between A and B causes the electric field to exert 0.052 J of work. When a charge q is transported from point A to point B, the potential difference between the two points is defined as the change in potential energy of the charge divided by the charge, or V = VB - VA. Voltage, also known as potential difference, is frequently abbreviated to V.
What is the potential difference VA VB formula?The SI unit for electric potential is volt (V). Potential difference is calculated using the method V = W/Q. Joules and Coulombs are the equivalent SI units for work and positive charge, respectively. Consequently, the formula can be written as VB-VA = WA B/Q.
To know more about electric field visit:-
https://brainly.com/question/15800304
#SPJ1
how can sonar best be used to monitor the hydrosphere
Sonar can be a useful tool for monitoring the hydrosphere, which includes all of the water on and beneath the Earth's surface.
Sonar works by emitting sound waves that bounce off objects in the water, and then measuring the time it takes for the sound waves to return to the source. By analyzing the echoes, scientists can map the seafloor, measure the depth of the water, and even identify the size and location of marine organisms.
Sonar can also be used to monitor the movements of water masses, including ocean currents, tides, and storm surges. This information is important for understanding global climate patterns and predicting the effects of natural disasters
Learn more about global climate
https://brainly.com/question/27919422
#SPJ4
Newton's first law of motion states that an object in motion will stay in motion unless acted upon by a force.
What are two forces on earth that could change the motion of the object?
Responses
friction and gravity
friction and gravity
speed and acceleration
heat and light
direction and time
The two forces on Earth that could change the motion of an object are friction and gravity.
Friction is a force that opposes the motion of an object when it is in contact with another surface. It can cause an object to slow down or come to a stop.
Gravity is a force of attraction between two objects, and it can cause an object to accelerate toward the center of the earth or towards another massive object. The gravitational force on an object depends on its mass and the distance between it and the other object.
Speed and acceleration are not forces, but rather measures of motion. Heat and light are also not forces that can change the motion of an object, but rather forms of energy that can be transferred to an object and affect its temperature or behavior. Direction and time are not forces, but concepts related to an object's motion.
Learn More about Newton's first law of motion:
https://brainly.com/question/1222214
a certain rifle bullet has a mass of 8.37 g. calculate the de broglie wavelength of the bullet traveling at 1793 miles per hour.
The de Broglie wavelength of the bullet traveling at 1793 miles per hour is approximately 9.90 x 10^-37 meters.
To calculate the de Broglie wavelength of the rifle bullet, we can use the formula:
λ = h / p
where λ is the de Broglie wavelength, h is the Planck constant (6.626 x 10^-34 J*s), and p is the momentum of the bullet. To find the momentum of the bullet, we can use the formula:
p = m * v
where m is the mass of the bullet (8.37 g = 0.00837 kg) and v is the velocity of the bullet in meters per second. First, we need to convert the velocity of the bullet from miles per hour to meters per second:
1793 miles/hour * 1609.34 meters/mile / 3600 seconds/hour = 800.1 meters/second
Now we can calculate the momentum of the bullet:
p = 0.00837 kg * 800.1 m/s = 6.703 k g m / s
Finally, we can use the momentum to calculate the de Broglie wavelength:
λ = 6.626 x 10^-34 J*s / 6.703 kg m/s = 9.90 x 10^-37 meters
Therefore, the de Broglie wavelength is approximately 9.90 x 10^-37 meters.
For more such questions on De Broglie wavelength.
https://brainly.com/question/11552854#
#SPJ11
The potential energy of an apple is 6.0 Joules. The apple is 1.22m high. What is the mass of the apple?
Answer:
The mass of the apple is 0.49kg
Explanation:
Potential energy=mgh
P=mgh
6=m×1.22×10
6=12.2m
divide both sides by 12.2
m=6/12.2
m=0.49kg
A wire, of length L = 3. 8 mm, on a circuit board carries a current of I = 2. 54 μA in the j direction. A nearby circuit element generates a magnetic field in the vicinity of the wire of B = Bxi + Byj + Bzk, where Bx = 6. 9 G, By = 2. 6 G, and Bz = 1. 1 G. A) Calculate the i component of the magnetic force Fx, in newtons, exerted on the wire by the magnetic field due to the circuit element.
B) Calculate the k component of the magnetic force Fz, in newtons, exerted on the wire by the magnetic field due to the circuit element.
C) Calculate the magnitude of the magnetic force F, in newtons, exerted on the wire by the magnetic field due to the circuit element
The i component of the magnetic force on the wire is 1.06 × 10^-13 N. The k component of the magnetic force on the wire is 6.69 × 10^-14 N. The magnitude of the magnetic force on the wire is 1.26 × 10^-13 N.
To calculate the i component of the magnetic force, we use the formula:
F = I * L x B
where I is the current, L is the length of the wire, B is the magnetic field, and x represents the cross product.
The cross product of L and B gives a vector perpendicular to both L and B, which is in the i direction. So we only need to find the magnitude of the cross product and multiply it by I to get Fx.
|L x B| = |L| |B| sinθ
where θ is the angle between L and B. Since L is in the j direction and B has i and k components, we have:
|L x B| = L * Bz = (3.8 × 10^-3 m) * (1.1 × 10^-4 T) = 4.18 × 10^-8 N
Then, Fx = I * |L x B| = (2.54 × 10^-6 A) * (4.18 × 10^-8 N) = 1.06 × 10^-13 N
To calculate the k component of the magnetic force, we use the same formula and take the k component of the cross product:
|L x B|k = |L| |B| sin(π/2) = |L| |B| = (3.8 × 10^-3 m) * (6.9 × 10^-5 T) = 2.63 × 10^-7 N
Then, Fz = I * |L x B|k = (2.54 × 10^-6 A) * (2.63 × 10^-7 N) = 6.69 × 10^-14 N
The magnitude of the magnetic force is given by,
F = sqrt(Fx^2 + Fz^2) = sqrt((1.06 × 10^-13 N)^2 + (6.69 × 10^-14 N)^2) = 1.26 × 10^-13 N
To know more about magnetic force, here
brainly.com/question/3160109
#SPJ4
the current is uniformly distributed in a wire with a diameter of 9.76 mm. find the magnetic field magnitude
To find the magnetic field of a wire with a diameter of 9.76 mm and a uniformly distributed current, you'll need to know the current (I) flowing through the wire, and the distance (r) from the center of the wire to the point where you want to measure the magnetic field. You can use Ampere's Law to determine the magnetic field (B).
1. Convert the diameter of the wire to meters: 9.76 mm = 0.00976 m.
2. Calculate the wire's radius: radius = diameter / 2 = 0.00976 m / 2 = 0.00488 m.
3. Determine the current (I) flowing through the wire. This information should be provided in the problem.
4. Determine the distance (r) from the center of the wire to the point where you want to measure the magnetic field.
5. Use Ampere's Law to calculate the magnetic field (B): B = (μ₀ * I) / (2 * π * r), where μ₀ is the permeability of free space (μ₀ = 4π x 10⁻⁷ Tm/A).
6. Plug in the values of I, μ₀, and r into the equation and solve for B.
Once you have followed these steps with the appropriate values for I and r, you will have found the magnetic field at the desired distance from the wire's center.
To know more about magnetic field:
https://brainly.com/question/23096032
#SPJ11
how fast is moving light that has traveled through transparent glass and exited on the opposite side with respect to the incoming speed?
The light that has traveled through transparent glass and exited on the opposite side will move at the same speed as it was moving before entering the glass, but it would have traveled slower while inside the glass.
The speed of light changes when it travels through a transparent medium like glass. The speed of light in vacuum or air is approximately 299,792,458 meters per second (often rounded to 3.00 x 10⁸ m/s), but it slows down when it passes through a medium like glass. The amount of slowing down depends on the refractive index of the material, which is a measure of how much the speed of light is reduced as it passes through the material.
For typical glasses, the refractive index is around 1.5, which means that the speed of light is reduced by a factor of about 1.5 when it passes through the glass. So, if the speed of light in vacuum or air is taken as 1, the speed of light in glass would be approximately 2/3 (or 0.67) of its original speed.
When the light exits the glass on the opposite side, it returns to its original speed in air or vacuum. Therefore, the light exits the glass with the same speed it had before it entered the glass, as long as it is not absorbed or scattered by the glass.
Learn more about the refractive index:
https://brainly.com/question/83184
#SPJ11
the value for ψ in root tissue was found to be -0.15 mpa. if you take the root tissue and place it in a 0.1 m solution of sucrose (ψ = -0.23 mpa), the net water flow would
The evaluated net water flow is 0.08 MPa under the context that 0.15 mpa is selected as the root tissue and placed it in a 0.1 m solution of sucrose ψ = -0.23 mpa.
Then water potential of root tissue = -0.15 MPa, now that of a 0.1 M solution of sucrose = -0.23 MPa. Then water potential gradient is
Δψ = ψ1 - ψ2
here
Δψ = water potential gradient,
ψ1 = water potential of root tissue
ψ2 = water potential of a 0.1 M solution of sucrose
Staging the values in the formula
Δψ = (-0.15) - (-0.23)
Δψ = 0.08 MPa
Hence, the level of sucrose solution has a lower in comparison to water potential present in the root tissue, therefore water will flow from the sucrose solution into the root tissue.
To learn more about water potential
https://brainly.com/question/6475956
#SPJ4
a student designed a pump cycle, in which 200 kj of heat removed from a reservoir at a temperature of 240 kelvin is rejected into another reservoir at a temperature of 400 k. the heat pump requires 100 kj of work. is the designated heat pump cycle reversible?
No, the heat pump cycle is not reversible.
The reversible process is an ideal process in which no energy is lost to the surroundings, and the system returns to its initial state when the process is reversed. In the given pump cycle, heat is transferred from a low-temperature reservoir to a high-temperature reservoir with the help of work input.
This process violates the second law of thermodynamics, which states that heat cannot flow spontaneously from a cold body to a hot body without any external work input. Therefore, the given pump cycle cannot be reversible.
Additionally, the efficiency of a reversible cycle is always greater than the efficiency of an irreversible cycle. In this case, the efficiency of the heat pump cycle can be calculated using the equation:
efficiency = (heat transferred - work input) / heat transferredSubstituting the given values, we get:
efficiency = (200 - 100) / 200 = 0.5 or 50%This efficiency is less than the maximum theoretical efficiency that a reversible cycle could achieve. Therefore, the pump cycle is irreversible.
To learn more about heat pump cycle, here
https://brainly.com/question/12937347
#SPJ4
polaris and the star at the other end of the little dipper, kochab, are both apparent magnitude 2. in a photo of the night sky, they would appear similar to how they appear here in a planetarium simulation: larger than other stars. this is because
Polaris and Kochab's apparent magnitude of 2 and their proximity to the celestial pole make them appear larger in a photo or planetarium simulation compared to other stars.
A comparatively brilliant star as compared to other stars in the night sky, Kochab and Polaris both have an apparent magnitude of 2, making them both bright stars. In addition, they are both close to the celestial pole, which gives them a motionless appearance in the sky while giving the impression that other stars are rotating around them.
They stand out in the night sky because of their fixed location and brightness, and because of their brightness and proximity to the celestial equator, they look bigger than other stars in pictures or planetarium simulations.
Learn more about planetariums:
https://brainly.com/question/23119731
#SPJ4
A nurse is caring for a client who is in labor and has an epidural anesthesia block. The client's blood pressure is 80/40 mmHg and the fetal heart rate is 140/min. Which of the followign is the priority nursing action?
A. Elevate the client's legs.
B. Monitor vital signs every 5 min.
C. Notify the provider.
D. Place the client in a lateral position.
The priority nursing action in this scenario would be to notify the provider.
An epidural anesthesia block can cause a drop in blood pressure in the mother, which can in turn affect the fetal heart rate.
A blood pressure reading of 80/40 mmHg is considered low, and can indicate hypotension.
Hypotension can lead to decreased blood flow to the placenta and fetus, which can result in fetal distress.
Therefore, it is important for the provider to be notified of the low blood pressure reading and fetal heart rate, so that appropriate interventions can be implemented to address the situation.
The provider may choose to adjust the dosage of the epidural anesthesia, administer IV fluids, or consider other measures to stabilize the mother's blood pressure and fetal well-being.
While monitoring vital signs and positioning the client can also be important interventions, they are not the priority in this scenario.
Elevating the client's legs may help to increase blood flow to the heart and improve blood pressure, and placing the client in a lateral position may also help to improve blood flow and prevent supine hypotensive syndrome.
These actions should be taken after the provider has been notified and appropriate interventions have been implemented.
To know more about epidural anesthesia visit link :
https://brainly.com/question/14205576
#SPJ11
earth's strong magnetic field indicates that the core is made of iron because the material in the core would have to be
Earth's strong magnetic field indicates that its core is made of iron due to several factors.
Firstly, iron is a highly magnetic material that can generate a significant magnetic field when it's in motion. In the Earth's core, the liquid outer core, which consists primarily of molten iron, flows around the solid inner core, also largely composed of iron.
This motion creates a self-sustaining dynamo effect, resulting in the generation of the Earth's magnetic field.
Secondly, the Earth's density distribution supports the presence of iron in the core.
The high density of the core, measured through seismic data, can only be explained if it's composed of heavy elements such as iron, combined with some lighter elements like nickel and sulfur.
In conclusion, the presence of iron in the Earth's core is supported by the strong magnetic field and the density distribution of our planet.
The molten iron in the outer core and the solid iron in the inner core plays a crucial role in generating and maintaining the Earth's magnetic field.
For more such answers on Magnetic Field
https://brainly.com/question/2950693
#SPJ11
danielle took an iron nail and wrapped thin copper wire around it, then connected the ends of the copper wire to a battery. which force or forces can danielle's device produce? responses only an electrical force only an electrical force both electrical and magnetic forces both electrical and magnetic forces both magnetic and gravitational forces both magnetic and gravitational forces only a gravitational force only a gravitational force
The forces are both, electrical and magnetic forces.
Which force or forces can Danielle's device produce?Hi! Danielle's device, which consists of an iron nail wrapped with a thin copper wire connected to a battery, can produce both electrical and magnetic forces. When the battery is connected, an electrical current flows through the copper wire, creating an electrical force. This current also generates a magnetic field around the wire, turning the iron nail into an electromagnet and producing a magnetic force. Therefore, the correct answer is both electrical and magnetic forces.
Learn more about forces
brainly.com/question/13191643
#SPJ11
at what rate is energy being dissipated as joule heat in the resistor after an elapsed time equal to the time constant of the circuit? answer in units of w.
The rate at which energy is being dissipated as Joule heat in a resistor can be calculated using the formula [tex]P=I^2R[/tex], and after an elapsed time equal to the time constant of the circuit, the power dissipated by the resistor can be given by [tex]P=0.4I^2 \times R[/tex].
The rate at which energy is being dissipated as Joule heat in a resistor is equal to the power dissipated by the resistor, which can be calculated using the formula [tex]P=0.4I^2\times R[/tex], where P is the power dissipated in watts, I is the current flowing through the resistor in amperes, and R is the resistance of the resistor in ohms.
After an elapsed time equal to the time constant of the circuit, the current flowing through the circuit will have reached approximately 63.2% of its maximum value. This is because the time constant of a circuit is equal to the product of the resistance and the capacitance, and it represents the amount of time it takes for the current in the circuit to reach 63.2% of its maximum value.
At this point, the power dissipated by the resistor can be calculated using the formula [tex]P=0.4I^2 \times R[/tex]. Since the current is 63.2% of its maximum value, we can substitute 0.632I for I in the formula. Therefore, the power dissipated by the resistor at this point is:
P = (0.632*I)^2 * R
= [tex]P=0.4I^2 \times R[/tex]
where I is the maximum current that will flow through the circuit, and R is the resistance of the resistor in ohms.
The rate at which energy is being dissipated as Joule heat in the resistor is equal to the power dissipated by the resistor, which is given by the above equation. Therefore, the answer to the question is:
Rate of energy dissipation = [tex]P=0.4I^2 \times R[/tex] watts
where I is the maximum current that will flow through the circuit, and R is the resistance of the resistor in ohms.
To learn more about resistors
https://brainly.com/question/24297401
#SPJ4
NEED HELP PLEASE.
QUESTION: imagine that you carry a box of books, weighing 67.8 N, up a flight of stairs. if each step is 15.0 cm high, and there are 22 steps in the flight of stairs, how much work do you do on the box of books
Answer:
The answer for Work done is ≈224J or 224Nm
Explanation:
Work done=F×D
F=mg
F=W
d=15×22=330cm=3.3m
W=67.8×3.3
W=223.74J or 223.7Nm
W≈224J or 224 Nm
If we know the size of an asteroid, we can determine its density by A) comparing its reflectivity to the amount of light it reflects. B) looking for brightness variations as it rotates. C) determining its mass from its gravitational pull on a spacecraft, satellite, or planet. D) radar mapping. E) spectroscopic imaging.
Option C) is correct in determining its mass from its gravitational pull on a spacecraft, satellite, or planet. Knowing the mass and size of an asteroid allows us to calculate its density.
Option A) is incorrect because reflectivity only tells us about the asteroid's surface properties, not its density. Option B) is incorrect because brightness variations during rotation do not give us enough information to determine density. Option D) and E) are methods of studying asteroids but are not directly related to determining density.
Knowing the size of an asteroid alone is not enough to determine its density, as different materials can have different densities at the same size. By measuring the gravitational pull of the asteroid on a spacecraft, satellite, or planet, we can determine its mass. Once we have the mass and the size, we can calculate the asteroid's density. Methods such as radar mapping and spectroscopic imaging can provide additional information about the asteroid's composition, but they are not directly used to determine its density.
To learn about gravitational pull please visit:
https://brainly.com/question/13467280
#SPJ11
C) calculating its mass based on the gravitational attraction it exerts on a satellite, planet, or spacecraft.
We can determine an asteroid's mass by observing the gravitational pull it has on a neighbouring body, like a planet, satellite, or spacecraft. We can determine the asteroid's density once we know its mass and size. The gravitational force of an object will be stronger the denser it is. As a result, an asteroid must be denser the more massive it is for a given size.
The density of an asteroid can be determined using this method, which is especially helpful for small or erratic-shaped asteroids that are challenging to see using other techniques like radar mapping or spectroscopic imaging. Additionally, it can offer crucial details on the asteroid's makeup and structure, which can aid researchers in understanding the asteroid's formation and evolution.
learn more about mass here:
https://brainly.com/question/18064917
#SPJ11
a particle with a cahrge of 1 c is moving at 45 angle with respect to the positive x axis in teh horizontal xy-plane. the velocity of the charge is 1 m/s. a magnetic field of 1 t is directed in the negative x direction. what is the magnetic force acting on the charge?
The magnetic force acting on the charged particle is -0.707 N in the k direction and 0.707 N in the j direction.
In this problem, the charge of the particle is given as 1 C, and the velocity of the particle is 1 m/s at an angle of 45 degrees to the positive x-axis. We can break down the velocity vector into its x and y components as follows:
vx = vcos(45) = 0.707 m/s
vy = vsin(45) = 0.707 m/s
The magnetic field is given as 1 T in the negative x direction.
Substituting these values into the formula for the magnetic force, we get:
F = q * (vxi + vyj + 0k) x (-Bi)
where I, j, and k are the unit vectors in the x, y, and z directions, respectively.
Expanding the cross product, we get:
F = q*(-vxB)k + qvyB*j
Substituting the values for q, vx, vy, and B, we get:
F = (1 C) (-0.707 m/s) (1 T) k + (1 C) (0.707 m/s) *(1 T) *j
Simplifying, we get:
F = -0.707 k + 0.707 j
To know more about Charge:
https://brainly.com/question/3412043
#SPJ4
a rocket is launched vertically upward from earth's surface at a speed of 5.5 km/s k m / s . part a what is its maximum altitude?
The maximum altitude of the rocket is 1,542 km. The result is obtained by using the kinematical equation.
Kinematic EquationThere are 3 main kinematical equations. They are
vf = vi + gtvf² = vi² + 2ghh = vi t + ½gt²Where vf is the final velocity, vi is the initial velocity, g is the acceleration due to gravity, and h is the displacement.
We have initial velocity 5.5 km/s. The question is to find the maximum altitude.
Let's convert the initial velocity from km/s to m/s.
5.5 km/s = 5,500 m/s
In this case, at the maximum altitude, the final velocity is zero, vf = 0. While the acceleration due to gravity is g = -9.81 m/s².
We can use the second equation to get the maximum altitude, h
vf² = vi² + 2gh
0 = 5,500² - 2(9.81)h
30,250,000 = 19.62 h
h = 1,541,794 meters
h ≈ 1,542 km
Therefore, the maximum altitude the rocket will reach is approximately 1,542 km.
Learn more about kinematical equation here:
brainly.com/question/31086903
#SPJ11
5 of 225 of 22 Items
12:41
Question
The basic concept of how a simple motor works is explained by which statement?
Answer:
The basic concept of how a simple motor works is that you put electricity into it at one end and an axle (metal rod) rotates at the other end giving you the power to drive a machine of some kind. The simple motors you see explained in science books are based on a piece of wire bent into a rectangular loop, which is suspended between the poles of a magnet. In order for a motor to run on AC, it requires two winding magnets that don’t touch. They move the motor through a phenomenon known as induction.
I hope this helps! Let me know if I'm wrong!
Explanation:
a hair drier uses 8 a at 114 v. it is used with a transformer in england, where the line voltage is 237 v. what should be the ratio of the turns of the transformer (primary to secondary)?
To determine the ratio of turns of the transformer, we can use the principle of conservation of power, which states that power in equals power out in an ideal transformer.
The power input to the hair dryer is:
P = VI = (8 A)(114 V) = 912 W
The power output of the transformer should be the same as the input power, so we can use this equation to find the current in the secondary circuit:
P = VI = (I_s)(237 V)
where I_s is the current in the secondary circuit. Solving for I_s, we get:
I_s = P/V_s = (912 W)/(237 V) = 3.85 A
Now we can use the turns ratio equation to find the ratio of the turns in the transformer:
N_p/N_s = V_p/V_s = (114 V)/(237 V)
where N_p and N_s are the number of turns in the primary and secondary coils, respectively. Solving for N_p/N_s, we get:
N_p/N_s = 0.481
Therefore, the ratio of turns in the transformer should be approximately 0.481.
To know more about conservation of power :
https://brainly.com/question/9013890
#SPJ11
a 3.0 m long rigid beam with a mass of 100 kg is supported at each end. an 80 kg student stands 2.0 m from support 1. how much upward force does each support exert on the beam?
Answer:
[tex]752.1\; {\rm N}[/tex] from support [tex]\texttt{1}[/tex] ([tex]2.0\; {\rm m}[/tex] from the student.)
[tex]1013.7\; {\rm N}[/tex] from support [tex]\texttt{2}[/tex] ([tex]1.0\; {\rm m}[/tex] from the student.)
(Assuming that [tex]g = 9.81\; {\rm N\cdot kg^{-1}}[/tex], the beam is level with negligible height, and that the density of the beam is uniform.)
Explanation:
Weight of the beam: [tex](100\; {\rm kg})\, (9.81\; {\rm N\cdot kg^{-1}}) = 981\; {\rm N}[/tex].
Weight of the student: [tex](80\; {\rm kg})\, (9.81\; {\rm N\cdot kg^{-1}}) = 784.8\; {\rm N}[/tex].
Assuming that the beam is uniform. The center of mass of the beam will be [tex](1/2)\, (3.0\; {\rm m}) = 1.5\; {\rm m}[/tex] away from each support.
Consider support [tex]\texttt{1}[/tex] as the fulcrum:
For support [tex]\texttt{2}[/tex] (with an upward force of [tex]N_{\texttt{2}}[/tex]), the lever arm is [tex]3.0\; {\rm m}[/tex].For the center of mass of the beam ([tex]981\; {\rm N}[/tex]), the lever arm is [tex]1.5\; {\rm m}[/tex].For the weight of the student ([tex]784.8\; {\rm N}[/tex]), the lever arm is [tex]2.0\; {\rm m}[/tex].Hence:
[tex]\begin{aligned}N_{\texttt{2}}\, (3.0) = (981)\, (1.5) + (784.8) \, (2.0) \end{aligned}[/tex].
[tex]\begin{aligned}N_{\texttt{2}} &= \frac{(981)\, (1.5) + (784.8) \, (2.0)}{3.0} \; {\rm N} = 1013.7\; {\rm N}\end{aligned}[/tex].
In other words, support [tex]\texttt{2}[/tex] would exert an upward force of [tex]1013.7\; {\rm N}[/tex] on the beam.
Similarly, consider support [tex]\texttt{2}[/tex] as the fulcrum:
For support [tex]\texttt{1}[/tex] (with an upward force of [tex]N_{\texttt{1}}[/tex]), the lever arm is [tex]3.0\; {\rm m}[/tex].For the center of mass of the beam ([tex]981\; {\rm N}[/tex]), the lever arm is [tex]1.5\; {\rm m}[/tex].For the weight of the student ([tex]784.8\; {\rm N}[/tex]), the lever arm is [tex](3.0 - 2.0)\; {\rm m} = 1.0\; {\rm m}[/tex].Hence:
[tex]\begin{aligned}N_{\texttt{1}}\, (3.0) = (981)\, (1.5) + (784.8) \, (1.0) \end{aligned}[/tex].
[tex]\begin{aligned}N_{\texttt{1}} &= \frac{(981)\, (1.5) + (784.8) \, (1.0)}{3.0} \; {\rm N} =752.1\; {\rm N}\end{aligned}[/tex].
In other words, support [tex]\texttt{1}[/tex] would exert an upward force of [tex]752.1\; {\rm N}[/tex] on the beam.
In Young's experiment, light from a red laser (wavelength 700 nm) is sent through two
slit. At the same time, monochromatic visible light with another wavelength passes through the same
apparatus. As a result, most of the pattern that appears on the screen is a mixture of two colors; however, the
center of the third bright fringe of the red light appears pure red. What are the possible wavelengths of the
second type of visible light?
In Young's experiment, the pattern that appears on the screen is a result of interference between two sets of waves that are diffracted through two slits.
The location of the bright fringes in the pattern depends on the wavelength of the light used. This means that the path difference between the waves that interfere to produce this fringe is an integer multiple of the red light's wavelength (700 nm).
ΔL = mλ_red = nλ_other
where ΔL is the path difference between the waves, m and n are integers, λ_red is the wavelength of the red light, and λ_other is the wavelength of the second type of visible light.
Solving for λ_other, we get:
λ_other = (m/n) λ_red.
To know more about Young's experiment, here
brainly.com/question/30452257
#SPJ4
What does it mean when we say our sense of motion depends on our frame of reference? Include the phrases “fixed frame” and “moving frame” in your answer.
frame of reference that is not inertial. A non-inertial frame is now defined as a frame that accelerates relative to the underlying inertial reference frame. Newton's law won't be valid.
How does the framework function?
Performance could change depending on the lighting. The Frame automatically modifies the Plasma tvs brightness and contrasting settings after analyzing the lighting conditions in the room and the light level of your content.
What distinguishes a system from a frame?
the hard architecture (bones and condyle) that serves as an animal's body's framework. skeletal system, skeleton, and systema skeletale. system: a collection of organs or bodily parts that function or are anatomically related; "the body contains a system for organs for digestion."
To know more about frame visit:
https://brainly.com/question/9708057
#SPJ1
Humerus
Sholder
Joint
2. What side of the chicken's body did this wing belong to? Why?
The upper limb is the side of the chicken's body did this wing belong to.
Where is the shoulder joint in a chicken?Humerus, shoulder, and joint are related to the anatomy of the upper limb. The humerus is the long bone in the upper arm, the shoulder is the joint that connects the arm to the body, and the joint refers to the articulation between bones.
In a chicken, the shoulder joint is located at the junction of the humerus (upper arm bone) and the scapula (shoulder blade). It is a ball-and-socket joint that allows for a wide range of motion in the chicken's wing. The shoulder joint is important for a chicken's ability to fly, flap its wings, and perform other movements that require mobility and stability in the upper limb.
Read more on upper limb here:https://brainly.com/question/6963710
#SPJ1
starting from rest, a disk rotates about its central axis with constant angular acceleration. in 5.0 s, it rotates 50 rad. what is the instantaneous angular velocity of the disk at the end of the 20.0 s?
The instantaneous angular velocity is 20.0 s is 400 rad/s.
What is the final instantaneous angular velocity of a disk rotating about its central axis with constant angular acceleration?Since the angular acceleration is constant, we can use the formula:
[tex]θ = 1/2 * α * t^2 + ω0 * t[/tex]
where
[tex]θ = angle rotated = 50 rad[/tex]
[tex]α = angular acceleration[/tex]
[tex]t = time = 5.0 s[/tex]
[tex]ω0 = initial angular velocity = 0 (starting from rest)[/tex]
Solving for α, we get:
[tex]α = 2 * (θ - ω0 * t) / t^2 = 2 * 50 rad / 5.0 s^2 = 20 rad/s^2[/tex]
Now, using the formula:
[tex]ω = α * t + ω0[/tex]
where
ω = instantaneous angular velocity at the end of 20.0 s (what we need to find)
[tex]α = angular acceleration = 20 rad/s^2[/tex]
[tex]t = time = 20.0 s[/tex]
[tex]ω0 = initial angular velocity = 0 (starting from rest)[/tex]
we get:
[tex]ω = 20 rad/s^2 * 20.0 s + 0 = 400 rad/s[/tex]
Therefore, the instantaneous angular velocity of the disk at the end of 20.0 s is 400 rad/s.
Learn more about angular acceleration
brainly.com/question/29428475
#SPJ11
this question has multiple answers. choose all that are correct. the hotter an object group of answer choices the brighter the object. the faster the object. the redder the object. the dimmer the object. the bluer the object. the slower the object.
The hotter an object is, the brighter and redder it appears, while cooler objects appear dimmer and bluer.
The question is asking about the relationship between an object's temperature and its brightness, color, and speed. The correct answers are that the hotter an object is, the brighter it appears and the redder it appears.
This is because hot objects emit more light, including more of the red end of the spectrum. The opposite is also true, meaning that cooler objects appear dimmer and bluer.
The speed of an object is not directly related to its temperature, so that answer is incorrect. However, it is important to note that the temperature of an object can affect its movement and velocity in certain situations.
To learn more about : objects
https://brainly.com/question/28308143
#SPJ11
it takes light approximately 8 minutes to reach the earth from the surface of the sun. the distance between jupiter and the sun is five astronomical units (5 au). how long does it take light to travel that distance?
It takes light approximately 39.5 minutes to travel the distance from the Sun to Jupiter.
Since it takes light approximately 8 minutes to reach the Earth from the surface of the sun, we know that the distance between the sun and the Earth is 1 astronomical unit (1 au).
Therefore, to find out how long it takes light to travel 5 au (the distance between Jupiter and the sun), we can use the following formula:
time = distance ÷ speed of light
The speed of light is approximately 299,792,458 meters per second.
So,
time = 5 au x 149,597,870,700 meters/au ÷ 299,792,458 meters/second
time = 39.5 minutes
Therefore, it takes approximately 39.5 minutes for light to travel from the surface of the sun to Jupiter.
Know more about astronomical unit here:
https://brainly.com/question/15211176
#SPJ11