Answer:
HF I am writing this email with your company is it a try and make them easier for us and we will need a new job and then email
An asphalt concrete mixture includes 94% aggregate by weight. The specific gravities of aggregate and asphalt are 2.65 and 1.0, respectively. The unit weight of water is 62.4 lb/ft3. The total weight of the mix is 147 Ib and the total volume is 1 ft3. Ignoring absorption, what is the percent voids in the total mix
Answer:
percent voids = 2.36%
Explanation:
Theoretical specific gravity ( Gt ) = ( w1 + wL ) / (( w1/G1) + (wL/GL ) )
= ( 94 + 6 ) / ((94/2.65) + ( 6 / 1.0 ))
∴ Gt = 2.411
next determine mass specific gravity = Ym / 1000
Bulk density = mass / volume = 147 Ib / 1ft^3 = 147 Ib/ft^3
given that: 1 Ib/ft^3 = 16.018 kg/m63
147 Ib/ft^3 = 2354.646 kg/m^3 ( Ym )
hence mass specific gravity = 2354.646 kg/m^3 / 1000
Gm = 2.354
finally determine percent void
= ( Gt - Gm ) / ( Gt ) * 100
= ( 2.411 - 2.354 ) / ( 2.411 ) * 100
= 2.36 %
A cylindrical rod of copper (E = 110 GPa) having a yield strength of 240 MPa is to be subjected
to a load of 6660 N. If the length of the rod is 380 mm, what must be the diameter to allow an
elongation of 0.50 mm?
Answer:
"7.654 mm" is the correct solution.
Explanation:
According to the question,
[tex]E=110\times 10^3 \ N/mm^2[/tex][tex]\sigma_y = 240 \ mPa[/tex][tex]P = 6660 \ N[/tex][tex]L = 380 \ mm[/tex][tex]\delta = 0.5 \ mm[/tex]Now,
As we know,
The Elongation,
⇒ [tex]E=\frac{\sigma}{e}[/tex]
[tex]=\frac{\frac{P}{A} }{\frac{\delta}{L} }[/tex]
or,
⇒ [tex]\delta=\frac{PL}{AE}[/tex]
By substituting the values, we get
[tex]0.5=\frac{6660\times 380}{(\frac{\pi}{4}D^2)(110\times 10^3)}[/tex]
then,
⇒ [tex]D^2=58.587[/tex]
[tex]D=\sqrt{58.587}[/tex]
[tex]=7.654 \ mm[/tex]
forty gal/min of a hydrocarbon fuel having a spesific gravity of 0.91 flow into a tank truck with load limit of 40,000 lb of fuel. How long will it takee to fill the tank in the truck?
Answer: 131.75minutes
Explanation:
First if all, we've to find the density of liquid which will be:
= Specific gravity × Density to pure water
= 0.91 × 8.34lb/gallon
= 7.59lb/gallon
Then, the volume that's required to fill the tank will be:
= Load limit/Density of fluid
= 40000/7.59
= 5270.1gallon
Now, the time taken will be:
= V/F
= 5270.1/40
= 131.75min
It'll take 131.75 minutes to fill the tank in the truck.
Could anyone answer this, please? It's about solid mechanics. I will give you 100 points!!! It's due at midnight.
Answer:
sorry i don't know
Explanation:
A center-point bending test was performed on a 2 in. x d in. wood lumber according to ASTM D198 procedure with a span of 4 ft and the 4 in. side is positioned vertically. If the maximum load was 240 kips and the modulus of rupture was 940.3 ksi, what is the value of d
Answer:
3.03 INCHES
Explanation:
According to ASTM D198 ;
Modulus of rupture = ( M / I ) * y ----- ( 1 )
M ( bending moment ) = R * length of span / 2
= (120 * 10^3 ) * 48 / 2 = 288 * 10^4 Ib-in
I ( moment of inertia ) = bd^3 / 12
= ( 2 )*( d )^3 / 12 = 2d^3 / 12
b = 2 in , d = ?
length of span = 4 * 12 = 48 inches
R = P / 2 = 240 * 10^3 / 2 = 120 * 10^3 Ib
y ( centroid distance ) = d / 2 inches
back to equation ( 1 )
( M / I ) * y
940.3 ksi = ( 288 * 10^4 / 2d^3 / 12 ) * d / 2
= ( 288 * 10^4 * 12 ) / 2d^3 ) * d / 2
940300 = 34560000* d / 4d^3
4d^3 ( 940300 ) = 34560000 d ( divide both sides with d )
4d^2 = 34560000 / 940300
d^2 = 9.188 ∴ Value of d ≈ 3.03 in
A continuous and aligned fiber-reinforced composite is manufactured using 80 vol% aramid fiber (a kevlar-like compound) embedded nylon 6-6. A part for a high-performance aircraft utilizes this composite. If the part experiences 953 lb-f (pounds force) along the fiber alignment axis, what is the force conveyed by the fibers ?
Answer:
the force conveyed by the fibers is 947.93 lb-f
Explanation:
Given the data in the question;
V_f = 80% = 0.8
V_m = 1 - V_f = 1 - 0.8 = 0.2
Now,
length of fibre L_f = length of Nylon L_n
V_f = A_f × L_f = 0.8
V_m = A_n × L_n = 0.2
so
V_f/V_m = A_f/A_n = 0.8/0.2
A_f/A_n = 4
now, the strains in fibre is equal to strains in nylon
(P/AE)f = (P/AE)n
P_f/A_fE_f = P_n/A_nE_n
P_f = (A_f/A_n)(E_f/E_n)(P_n)
P_f = ( 4 )( 131 / 2.8 )(Pn)
P_f = 187.14Pn
and P_n = Pf / 187.14
Hence
given that P_total = 953 lb-f
P_f + P_n = 953
P_f + ( P_f / 187.14 ) = 953
P_f( 1 + ( 1 / 187.14 ) ) = 953
P_f( 1.00534359 = 953
P_f = 953 / 1.00534359
P_f = 947.93 lb-f
Therefore, the force conveyed by the fibers is 947.93 lb-f
Air at 308C, 1 bar, 50% relative humidity enters an insulated chamber operating at steady state with a mass flow rate of 3 kg/min and mixes with a saturated moist air stream entering at 58C, 1 bar with a mass flow rate of 5 kg/min. A single mixed stream exits at 1 bar. Determine (a) the relative humidity and temperature, in 8C, of the exiting stream. (b) the rate of exergy destruction, in kW, for T0 5 208C. Neglect kinetic and potential energy effects.
Answer: the question of whether or is that a new place for a person to come in the morning and then the day that we have a good day at school or to come home with us to go to the church or we could meet up at my place in about a week or so to get the rest of the kids and I can go out to the school to go to the gym to go to the doctor to pick them out or not I have a good time to come over to get the stuff out of the car so I’m going out of the house to go to the store to pick it out I don’t have any money for that
Explanation:
Air is compressed from 100 kPa, 300 K to 1200 kPa in a two-stage compressor with intercooling between the stages. The intercooler pressure is 400 kPa. The air is cooled back to 300 K in the intercooler before entering the second compressor stage. Each compressor stage is isentropic. For steady-state operation and negligible changes in kinetic and potential energy from inlet to exit, determine (a) the temperature at the exit of the seco
Answer:
410.7 K
Explanation:
Given data:
P1 ( initial air pressure ) = 100 kPa
Pi ( intercooler pressure ) = 400 kPa
P2( compressed air pressure ) = 1200 kPa
T1 = 300 k
Ti = 300 k
Calculate for the temperature at the exit of the second stage ( T2 )
we can calculate this using the relation below
T2 / Ti = ( P2/Pi )^(r-1/r)
∴ T2 = 300 ( 1200 / 400 )^( 1.4 - 1 / 1.4 )
= 300 ( 3 )^0.286
= 300 * 1.369 = 410.7 K
In a ground-water basin of 12 square miles, there are two aquifers: an upper unconfined aquifer 500 ft in thickness and a lower confined aquifer with an available hydraulic head drop of 150 ft. Hydraulic tests have determined that the specific yield of the upper unit is 0.12 and the storativity of the lower unit is 4x10-4. What is the amount of recoverable ground water in the basin
Answer:
0.1365 m^3
Explanation:
thickness of upper aquifer = 500 ft
lower aquifer head drop = 150 ft
area of ground water basin = 12 m^2
specific yield of upper unit = 0.12
Storativity of lower unit = 4 * 10^-4
determine the amount of recoverable ground water
first step : calculate volume of unconfined aquifer
= 12 * 500/5280 = 1.1364 miles^3
The recoverable volume of water from unconfined aquifer
= 1.1364 * 0.12 = 0.1364 miles^3
next : calculate volume of confined aquifer
= 12 * 150/5250 = 0.341 miles^3
The recoverable volume of water from confined aquifer
= 0.341 * ( 4 * 10^-4 ) = 1.364 * 10^-4 miles^3
Hence the amount of recoverable ground water in the basin
= ∑ recoverable ground water from both aquifer
= 0.1365 m^3
The blue and white “Alfa” flag signifies what?
A) A tow boat is towing another vessel to safety
B) A ski boat that has a participant in the water
C) A dive boat that is restricted in its ability to maneuver
D) A Coast Guard boat that is on patrol
The blue and white "Alfa" flag signifies: C. a dive boat that is restricted in its ability to maneuver.
What is a dive boat?A dive boat can be defined as a type of boat that is commonly used by scuba divers or recreational divers to reach a deep dive site which cannot be conveniently accomplished by swimming from the bank or sea shore.
As a safety precaution, the blue and white "Alfa" flag is designed and developed to signify a dive boat that is restricted in its ability to maneuver.
Read more on dive boat here: https://brainly.com/question/23462572
#SPJ2
Q2 [45 marks] Consider Ibra region where the installed solar panels cost on average 2 OMR /W.
[10 marks] What is the cost to install a 5kW PV system for a residence?
[10 marks] If the solar irradiance in Ibra is on average 800W/m2 and the installed panels have efficiency of 18%. How many panels are required if the panel’s area is 2m2?
[15 marks] Assume Ibra has an average of 10 day-hours, dusty environment which causes the efficiency of the solar system to drop by 10% on average, and 30 cloudy days/year which cause the efficiency of the solar panels drops by 50%. If electrical power cost per kWh is 0.05 OMR determine the break-even time for the 5kW PV system.
[10 marks] If the system to be off-grid, what would be the backup time if three 12-V batteries were selected each with a capacity of 200Ah. Assume that you can discharge the batteries up to 80% of their capacities.
Answer:
so hard it is
Explanation:
I don't know about this
please mark as brainleast
byýyy