Answer:
cos to = $ 24
Explanation:
When replacing the bulb only 25% of the energy is used, therefore
W = 0.25 100
W = 25 W
Let's look for the energy in the life of the bulb
E = 25 10⁻³ 12000
E = 300 Kwh
now we can calculate the cost using a direct proportion rule.
Cost = 0.08 300
cos to = $ 24
Write a paragraph descibing three rides in an amusement park and how rides cause you
to move.
Answer:
Hope this helps! can I have brainliest im trying to level up.
Explanation:
Bumper cars are a great place to see Sir Isaac Newton’s three laws of motion in action. Here’s how:
Newton’s First Law: Every object in motion continues in motion and every object at rest continues to be at rest unless an outside force acts upon it.
This is because all objects have inertia – the property of matter that resists changes to the object’s motion.
Newton found that if a ball is sitting on a table, it will stay sitting there because that is what it ‘wants’ to do.
If the ball is set in motion, it will keep traveling in a straight path because, again, that is what it ‘wants’ to do.
An object in motion will not stop, slow down, or change its direction unless an outside force acts on it (such as gravity, friction, and air resistance).
When you are riding in a bumper car and end up in a collision with another bumper car, you feel a jolt. This is because your body’s inertia wants it to keep traveling in the direction it was moving with the car even though your bumper car has now suddenly stopped.
Newton’s Second Law: The greater the mass of an object, the harder it is to change its speed.
(More force is needed to move it.)
You already know this law and practice it in your everyday life. Something that is small, such as a pebble, is much easier to pick up and throw than something that is large and heavy, such as a boulder.
When riding in the bumper cars, you may have noticed that people who weigh less tend to get pushed around more than people who weigh more.
The more mass (weight) an object has, the more force it takes to move it.
And since all the bumper cars usually have the same top velocity, the cars carrying more mass will never travel as far as the cars carrying less mass after a collision.
Newton’s Third Law: For every action, there is an equal and opposite reaction.
If two bumper cars traveling at the same speed and carrying the same amount of weight run into each other, they will bounce off and move an equal distance away from each other.
And based on the second law, if there is a difference in the amount of weight being carried in the two cars, the car with less weight will travel farther away from the point of impact than the car carrying more weight.
Find the frequency and wavelength of the wave below, assuming it has a speed of 30 m/s
A ball is rolling away from you at a constant speed, hits a wall, and then suddenly stops moving. Imagine a position-versus-time graph showing the ball’s motion. Describe the line on the graph.
Answer:
It would show a "straight line".
Explanation:
Newton's First Law of Motion states that an object at rest will remain at rest and an object in motion will remain in motion (at a constant velocity) unless acted upon by an unbalanced force. Newton's first law of motion is also called the law of inertia.
A plate of uniform areal density is bounded by the four curves: where and are in meters. Point has coordinates and . What is the moment of inertia of the plate about point
The question is incomplete. The complete question is :
A plate of uniform areal density [tex]$\rho = 2 \ kg/m^2$[/tex] is bounded by the four curves:
[tex]$y = -x^2+4x-5m$[/tex]
[tex]$y = x^2+4x+6m$[/tex]
[tex]$x=1 \ m$[/tex]
[tex]$x=2 \ m$[/tex]
where x and y are in meters. Point [tex]$P$[/tex] has coordinates [tex]$P_x=1 \ m$[/tex] and [tex]$P_y=-2 \ m$[/tex]. What is the moment of inertia [tex]$I_P$[/tex] of the plate about the point [tex]$P$[/tex] ?
Solution :
Given :
[tex]$y = -x^2+4x-5$[/tex]
[tex]$y = x^2+4x+6$[/tex]
[tex]$x=1 $[/tex]
[tex]$x=2 $[/tex]
and [tex]$\rho = 2 \ kg/m^2$[/tex] , [tex]$P_x=1 \ $[/tex] , [tex]$P_y=-2 \ $[/tex].
So,
[tex]$dI = dmr^2$[/tex]
[tex]$dI = \rho \ dA \ r^2$[/tex] , [tex]$r=\sqrt{(x-1)^2+(y+2)^2}$[/tex]
[tex]$dI = (\rho)((x-1)^2+(y+2)^2)dx \ dy$[/tex]
[tex]$I= 2 \int_1^2 \int_{-x^2+4x-5}^{x^2+4x+6}((x-1)^2+(y+2)^2) dy \ dx$[/tex]
[tex]$I= 2 \int_1^2 \int_{-x^2+4x-5}^{x^2+4x+6}(x-1)^2+(y+2)^2 \ dy \ dx$[/tex]
[tex]$I=2 \int_1^2 \left( \left[ (x-1)^2y+\frac{(y+2)^3}{3}\right]_{-x^2+4x-5}^{x^2+4x+6}\right) \ dx$[/tex]
[tex]$I=2 \int_1^2 (x-1)^2 (2x^2+11)+\frac{1}{3}\left((x^2+4x+6+2)^3-(-x^2+4x-5+2)^3 \ dx$[/tex]
[tex]$I=\frac{32027}{21} \times 2$[/tex]
[tex]$= 3050.19 \ kg \ m^2$[/tex]
So the moment of inertia is [tex]$3050.19 \ kg \ m^2$[/tex].
A capacitor is constructed of two large, identical, parallel metal plates separated by a small distance d
a. True
b. False
Does an infrared wave or an x-ray travel faster in the vacuum of space?
Answer:
All electromagnetic radiation, of which radio waves and X-rays are examples, travels at the speed c in a vacuum. The only difference between the two is that the frequency of X-rays is very much higher than radio waves
En una balanza de fábrica se determina la masa de un cuerpo y se obtiene
1 M kg 280
con
un error aparente
1 1 0,5 a
M kg
. En un laboratorio, se hace lo mismo con otro cuerpo y
se determina
2 M g 23,545
con un error
2 2 0,001 a
M g .
¿Dónde se cometió mayor erro
Tawny notices that Jim has been forgetting to check two forms of
identification for new patients. How could she best communicate this
effectively to Jim in a way that avoids conflict?
A. "I forget this a lot, too, so I'm not blaming you or anything, but you
need to check two forms of identification."
B. "Did you forget your training? We always have to check two forms
of identification for each patient."
C. "We have to check two forms of identification, so stop forgetting
to do it."
D. "I think the proper procedure is to check two forms of
identification for each patient."
Answer: D. "I think the proper procedure is to check two forms of
identification for each patient."
Explanation: took the quiz
The speed of a wave is 40 m/s. If the wavelength is 80 centimeters, what is the frequency of the wave?
SOLVE IT COMPLETELY
The speed of a wave is 40 m/s. If the wavelength is 80 centimeters, what is the frequency of the wave ?
Answer:-Given:-Velocity (V) = 40 m/s
Wavelength [tex] (\lambda) [/tex] = 80 cm = 0.8 m
To Find:-The frequency (F) of the wave.
Solution:-We know,
[tex] \bf V \: = \: F \: × \: \lambda [/tex]
40 = F × 0.8
F = [tex] \frac{40}{0.8} [/tex]
F = 50
The frequency of the wave is 50 Hz. [Answer]19
What is the mass of a ball that is traveling 30 m/s and has 4.5 J of kinetic energy?
ave a GPF of 35512
Answer: The mass of ball is 10 grams.
Explanation:
Given : Kinetic energy = 4.5 J
Velocity = 30 m/s
The formula for Kinetic energy is as follows.
[tex]K.E = \frac{1}{2}mv^{2}[/tex]
where,
K.E = Kinetic energy
m = mass
v = velocity
Substitute the values into above formula as follows.
[tex]K.E = \frac{1}{2}mv^{2}\\4.5 J = \frac{1}{2} \times m \times (30 m/s)^{2}\\m = \frac{4.5 J \times 2}{900 m^2/s^2} (1 Js^{2} = kg m^{2})\\= 0.01 kg (1 kg = 1000 g)\\= 10 g[/tex]
Thus, we can conclude that the mass of ball is 10 grams.
51.Shoveling snow can be extremely taxing because the arms have such a low efficiency in this activity. Suppose a person shoveling a footpath metabolizes food at the rate of 800 W. (a) What is her useful power output? (b) How long will it take her to lift 3000 kg of snow 1.20 m? (This could be the amount of heavy snow on 20 m of footpath.) (c) How much waste heat transfer in kilojoules will she generate in the process?
Complete question is;
Shoveling snow can be extremely taxing since the arms have such a low efficiency in this activity. Suppose a person shoveling a sidewalk metabolizes food at the rate of 800 W. (The efficiency of a person shoveling is 3%.)
(a) What is her useful power output? (b) How long will it take her to lift 3000 kg of snow 1.20 m? (This could be the amount of heavy snow on 20 m of footpath.) (c) How much waste heat transfer in kilojoules will she generate in the process?
Answer:
A) P_out = 24 W
B) t = 1470 s
C) Q = 1140.72 KJ
Explanation:
We are given;
Input Power; P_in = 800 W
Efficiency; η = 3% = 0.03
A) Formula for efficiency is;
η = P_out/P_in
Making P_out the subject, we have;
P_out = η•P_in
P_out = 0.03 × 800
P_out = 24 W
B) We know that;
Power = work done/time taken
Thus;
P_out = mgh/t
We are given;
m = 3000 kg
h = 1.20 m
Thus, time is;
t = (3000 × 9.8 × 1.2)/24
t = 1470 s
C) amount of heat wasted is calculated from;
Q = (P_in - P_out)t
Q = (800 - 24) × 1470
Q = 1,140,720 J
Q = 1140.72 KJ
Which of the following is not a characteristic of electrical potential energy?
Answer:
It is a form of mechanical energy
Explanation:
PLS HELP, WILL GIVE BRAINLIEST!!!
A piece of clay with a mass of 350 g is dropped to the floor from a height of 1.5 m (A). Calculate the KE and PE of the clay at
a. (A = 1.5 m).
b. (B = 70 cm), and
c. (C = 0 m, just before hitting the ground). d. Make an energy graph at each point
Answer:
b bro it's b bro
Question 3
By what volume would 25 L of alcohol increase if its temperature was
increased from 20°C to 30°C? (3 marks)
Answer:
V2 = 37.5 L
Explanation:
Given the following data;
Initial volume, V1 = 25 L
Initial temperature, T1 = 20°C
Final temperature,T2 = 30°C
To find the final volume V2, we would use Charles' law;
Charles states that when the pressure of an ideal gas is kept constant, the volume of the gas is directly proportional to the absolute temperature of the gas.
Mathematically, Charles is given by;
[tex] \frac {V}{T} = K[/tex]
[tex] \frac{V_{1}}{T_{1}} = \frac{V_{2}}{T_{2}} [/tex]
Making V2 as the subject formula, we have;
[tex] V_{2}= \frac{V_{1}}{T_{1}} * T_{2}[/tex]
[tex] V_{2}= \frac{25}{20} * 30 [/tex]
[tex] V_{2}= 1.25 * 30 [/tex]
V2 = 37.5 L
a car initially at rest move with the constant accerates along straght line read after it's spread increase and finally related uniformly. the time interval for the three parts of the jounry are in the ratio 1:3:1 find average velocity ?
Answer:
32km per hour
Explanation:
Explanation:
In first case v = a t
==> a t = 40 km p h
Now distance covered S1 + S2 + S3
S1 = 1/2 a t^2 and S3 = 1/2 a t^2
But S2 = 3t * 40 = 120 t km
Hence total distance = at^2 + 120 t
Time taken (total) = t + 3t + t = 5 t
Hence average speed = at^2 + 120 t / 5 t
Cancelling t we have at + 120 / 5 = 40 + 120 / 5 = 160/5 = 32 km per hour
An electron of kinetic energy 1.59 keV circles in a plane perpendicular to a uniform magnetic field. The orbit radius is 35.4 cm. Find (a) the electron's speed, (b) the magnetic field magnitude, (c) the circling frequency, and (d) the period of the motion.
Answer:
a) [tex] v = 2.36 \cdot 10^{7} m/s [/tex]
b) [tex] B = 3.80 \cdot 10^{-4} T [/tex]
c) [tex] f = 1.06 \cdot 10^{7} Hz [/tex]
d) [tex] T = 9.43 \cdot 10^{-8} s [/tex]
Explanation:
a) We can find the electron's speed by knowing the kinetic energy:
[tex] K = \frac{1}{2}mv^{2} [/tex]
Where:
K: is the kinetic energy = 1.59 keV
m: is the electron's mass = 9.11x10⁻³¹ kg
v: is the speed =?
[tex] v = \sqrt{\frac{2K}{m}} = \sqrt{\frac{2*1.59 \cdot 10^{3} eV*\frac{1.602 \cdot 10^{-19} J}{1 eV}}{9.11 \cdot 10^{-31} kg}} = 2.36 \cdot 10^{7} m/s [/tex]
b) The electron's speed can be found by using Lorentz's equation:
[tex] F = q(v\times B) = qvBsin(\theta) [/tex] (1)
Where:
F: is the magnetic force
q: is the electron's charge = 1.6x10⁻¹⁹ C
θ: is the angle between the speed of the electron and the magnetic field = 90°
The magnetic force is also equal to:
[tex] F = ma_{c} = m\frac{v^{2}}{r} [/tex] (2)
By equating equation (2) with (1) and by solving for B, we have:
[tex] B = \frac{mv}{rq} = \frac{9.11 \cdot 10^{-31} kg*2.36 \cdot 10^{7} m/s}{0.354 m*1.6 \cdot 10^{-19} C} = 3.80 \cdot 10^{-4} T [/tex]
c) The circling frequency is:
[tex] f = \frac{1}{T} = \frac{\omega}{2\pi} = \frac{v}{2\pi r} [/tex]
Where:
T: is the period = 2π/ω
ω: is the angular speed = v/r
[tex] f = \frac{v}{2\pi r} = \frac{2.36 \cdot 10^{7} m/s}{2\pi*0.354 m} = 1.06 \cdot 10^{7} Hz [/tex]
d) The period of the motion is:
[tex] T = \frac{1}{f} = \frac{1}{1.06 \cdot 10^{7} Hz} = 9.43 \cdot 10^{-8} s [/tex]
I hope it helps you!
SOMEONE HELP PLEASE I ASKED THIS TWICE LAST NIGHT I MEAN DAM!! You drop a water balloon from a second-story window. Which formula would you use to calculate the velocity of the water balloon just before it hits the ground, assuming it is in free fall?
A. v=g/t B. v=get C. g=vt D. t=vg
Answer:
I think it would be V=g/t
Which statement identifies a true relationship between the various wave components?
If amplitude increases, frequency increases.
If frequency increases, wavelength decreases.
If wavelength decreases, amplitude decreases.
Answer:
it's the second one;
if the frequency increases, wavelength decreases
Explanation:
we know, v=f×lamda(wave length)
so for constant velocity Frequency f is inversely proportional to lamda
i.e.
fα 1/lamda
so as the f increases lamda decreases and vise versa
A true relationship between the various wave components is if frequency increases, wavelength decreases.
What is the frequency?The frequency is the reciprocal of the time period of the wave.
The wavelength is the distance between the two adjacent crest of the wave.
If the wavelength decreases, the number of cycles will increase in a certain time.
Hence, a true relationship between the wave components is if frequency increases, wavelength decreases.
Learn more about Frequency.
https://brainly.com/question/5102661
#SPJ2
why is it important to observe safety rules in food preservation?
pls help
Answer:
Yes it is important.
Explanation:
It is important because we should preserve our food with safety as we would take it in the next day so if we we will not take safety then many germs can enter in that food and if we eat that food we could get sick . If we keep the food uncovered so anything can happen like any insect can fall in the food and we didn't know it it or any germs can enter in the food that is very harmful for our body so so we should keep the food covered and well preserved.
[tex]can \: you \: answer \: that[/tex]
Answer:
1. k
2. t
3. k
4. k
5. k
6. k
7. k
8. k
9. k
10. k
I'm not sure but hope it helps:)
Aluminum has a shear strength of 210 megapascals. When you bend aluminum foil around an edge (i.e., the edge of the box) and pull, you are effectively applying a shear force along the bent edge of the foil. If a roll of household aluminum foil is 30.0 centimeters wide and its thickness is approximately 15.0 micrometers, how much shear force is needed to pull off a sheet
Answer:
The answer is "[tex]945\ N[/tex]"
Explanation:
Aluminum has 210 megapascals of tensile resistance. They choose a shear force only at bent foil edge to bend aluminum foil over an edge (that is the edge of its box) to pull them. When a roll of aluminium domestic foil is 30 cm in width and about 15.0 micrometers.
[tex]\to 0.000015 \times 0.300 = 0.0000045\\\\\to 210000000 = \frac{F}{0.0000045}\\\\\to F=210000000 \times 0.0000045\\\\\to F = 945\ N[/tex]
Which two mixtures are homogeneous?
Answer:
sand and air
Explanation:
air is a mix of carbon dioxide and oxygen and sand is a mix of rocks and stuff
Q1. Helmut rides 5km in 2h on his bike. His speed was *
a) 10km/h
b) 2.5km/h
c) 0.4km/h
d) 2.5km
Q2. A plane is travelling at 250km/h and must reach a target that is 3h 58min away. The distance to the target is. *
a) 1000km
b) 89500km
c) 62.5km
d) not enough information
Answer:
Speed of bike = 2.5 km/h
Distance travel = 1,000 km (Approx.)
Explanation:
Given:
Distance cover by Helmut = 5 km
Time taken = 2 hour
Find:
Speed of bike
Computation:
Speed = Distance / Time
Speed of bike = 5 / 2
Speed of bike = 2.5 km/h
Given:
Speed of plane = 250 km/h
time taken = 3 hr 58 min = 3.967 hr
Find:
Distance travel
Computation:
Distance = Speed x time
Distance travel = 250 x 3.967
Distance travel = 991.669
Distance travel = 1,000 km (Approx.)
How does Newton's first law affect human motions answer
Three capacitors, C1 = 2 μF, C2 = 4 μF, C3 = 4 μF, are connected in series Determine the capacitance of a single capacitor that will have the same effect as the combination.
Answer:
1 μF
Explanation:
To obtain the answer to the question, all we need to do is to calculate the equivalent capacitance of the capacitors. This can be obtained as illustrated below.
From the question given above, the following data were obtained:
Capacitor 1 (C₁) = 2 μF
Capacitor 2 (C₂) = 4 μF
Capacitor 3 (C₃) = 4 μF
Equivalent capacitance (Cₑq) =?
Cₑq = 1/C₁ + 1/C₂ + 1/C₃
Cₑq = 1/2 + 1/4 + 1/4
Cₑq = (2 + 1 + 1)/4
Cₑq = 4/4
Cₑq = 1 μF
Thus, the answer to the question is 1 μF
When the electrons reach the collector, they flow towards the positivly charged grid. The resulting current is measured. Note that as the electrons accelerate from the cathode toward the grid, they collide with the mercury atoms. Assume that these collisions are completely elastic. How does the collected current vary if the ΔVgrid is slowly increased? View Available Hint(s) When the electrons reach the collector, they flow towards the positivly charged grid. The resulting current is measured. Note that as the electrons accelerate from the cathode toward the grid, they collide with the mercury atoms. Assume that these collisions are completely elastic. How does the collected current vary if the is slowly increased? The current increases. The current remains constant. The current decreases.
Answer:
the current INCREASES.
Explanation:
In this experiment, the electrons are generated by a filament with very low speed, when they are subjected to a difference and potential ΔV they acquire the necessary speed to reach the regulation and the current can be measured.
Some electrons collide elastically with the atoms of the mercury gas that is much heavier and are scattered in any direction, so they do not reach the grid, by increasing the voltage this scattered electrons can acquire the necessary speed in the direction of grid to reach it and therefore are also measured, increasing the current.
Therefore, as the power difference increases, the current INCREASES.
A 2.5 V battery is connected to a small light
bulb with a resistance of 4.8 Ω .
What is the current in the bulb?
Answer in units of A.
Answer: I=0.52 A
Explanation:
Given
Voltage is [tex]2.5\ V[/tex]
Resistance [tex]R=4.8\ \Omega[/tex]
Current is given by
[tex]I=\dfrac{V}{R}[/tex]
[tex]\Rightarrow I=\dfrac{2.5}{4.8}=0.52\ A[/tex]
Using a Boltzmann distribution, find the fraction of atoms in the excited state versus the ground state (i.e. the relative population) in a plasma source and a flame source. Assume that the lowest energy of a sodium atom lies at 3.371x10-19 J above the ground state, the degeneracy of the excited state is 2, whereas that of the ground state is 1, and the temperature of the flame is 3000 K and 10,000 K for plasma.
Answer:
0.174 plasma
[tex]$5.85 \times 10^{-4}$[/tex] flame
Explanation:
Given :
Energy :
[tex]$\Delta E=3.371 \times 10^{-19} $[/tex] J per atom
[tex]$g^*=2$[/tex] (degenraci of excited state)
g = 1 (degenraci of excited state)
Boltzmann Distribution
[tex]$\frac{N^*}{N}=\frac{g^*}{g}e^{-\frac{\Delta E}{kT}}$[/tex]
where,
[tex]$N^*$[/tex] = atoms in excited state
N = atoms in lower energy level
k = [tex]$1.38 \times 10^{-23}$[/tex] J/K
Therefore,
Relative population in plasma
T = 10,000 K
[tex]$\frac{N^*}{N}=\frac{g^*}{g}e^{-\frac{\Delta E}{kT}}$[/tex]
[tex]$\frac{N^*}{N}=\frac{2}{1}e^{-\frac{-3.37\times 10^{-19}}{1.38 \times 10^{-23} \times 10000}}$[/tex]
[tex]$\frac{N^*}{N}=2 \times e^{-2.44275}$[/tex]
[tex]$\frac{N^*}{N}=2 \times 0.8692$[/tex]
[tex]$\frac{N^*}{N}=0.1738$[/tex]
Relative population in flame
T = 3000
[tex]$\frac{N^*}{N}=\frac{g^*}{g}e^{-\frac{\Delta E}{kT}}$[/tex]
[tex]$\frac{N^*}{N}=\frac{2}{1}e^{-\frac{-3.371\times 10^{-19}}{1.38 \times 10^{-23} \times 3000}}$[/tex]
[tex]$\frac{N^*}{N}=2 \times e^{-8.1425}$[/tex]
[tex]$\frac{N^*}{N}=2 \times 2.9090 \times 10^{-4}$[/tex]
[tex]$\frac{N^*}{N}=5.85 \times 10^{-4}$[/tex]
Wind power is considered a renewable energy source.
O True
O False
Answer:
True
Explanation:
Answer:
your answer is true hope this helps
To obtain maximum Electromotive force (EMF), you should connect the batteries in
Answer:
Series
Cells in Series connection.In series, cells are joined end to end so that the same current flows through each cell. In case if the cells are connected in series the emf of the battery connected to the sum of the emf of the individual cell,If E is the overall emf of the battery combined with n number cells and E1, E2,......Em is the EMFs of individual cell.
Then
E= E1+E2+...............+Em.