Answer:
Since their wings and body develop the drag. When there is warm air then they expand their wings. Since,soaring birds and glider pilots have no engine, they always maintain their high speed to lift their weight in air for hours without expending power by convection
Explanation:
In a polar coordinate system, the velocity vector can be written as . The term theta with dot on top is called _______________________ angular velocity transverse velocity radial velocity angular acceleration
Answer:
I believe it's called rapid growth
Explanation:
that is my answer no matter what
Zack is driving past his house. He wants to toss his physics book out the window and have it land in his driveway. If he lets go of the book exactly as he passes the end of the driveway. Should he direct his throw outward and toward the front of the car (throw 1), straight outward (throw 2), or outward and toward the back of the car (throw 3)? Explain.
Answer:
Zack should direct his throw outward and toward the back of the car.
Explanation:
As the car is moving forward, the book will be thrown with a forward component. Therefore, throwing this book backwards at a constant speed would cancel the motion of the car, allowing the book to have a greater chance of ending on the driveway. I say a greater chance as Zack may not have the exact timings as to land the book in his driveway. That too he may not have thrown the book with the right momentum.
The solution is throw 3.
I say a greater chance as Zack may not have the exact timings as to land the book in his driveway. That too he may not have thrown the book with the right momentum as the skydivers.
Which statement best applies Newton’s laws of motion?The statement that best applies Newton’s laws of motion to explain the skydiver’s motion is that an upward force balances the downward force of gravity on the skydiver. Newton's 3rd law often applies to skydiving.
When gravity is not acting upon the skydivers they would continue moving in the direction the vehicle they jumped from was moving. If no air resistance takes place, then the skydivers would still accelerating at 9.8 m/s until they hit the ground.
The skydiver after leaving the aircraft will accelerates downwards due to the force of gravity usually as there is no air resistance acting in the upwards direction, and there is a resultant force acting downwards, the skydiver will accelerates towards the ground.
Therefore, I say a greater chance as Zack may not have the exact timings as to land the book in his driveway. That too he may not have thrown the book with the right momentum as the skydivers.
Learn more about skydiver on:
https://brainly.com/question/29253407
#SPJ6
A flat loop of wire consisting of a single turn of cross-sectional area 8.20 cm2 is perpendicular to a magnetic field that increases uniformly in magnitude from 0.500 T to 2.60 T in 1.02 s. What is the resulting induced current if the loop has a resistance of 2.70
Answer:
The induced current is [tex]I = 6.25*10^{-4} \ A[/tex]
Explanation:
From the question we are told that
The number of turns is [tex]N = 1[/tex]
The cross-sectional area is [tex]A = 8.20 cm^2 = 8.20 * 10^{-4} \ m^2[/tex]
The initial magnetic field is [tex]B_i = 0.500 \ T[/tex]
The magnetic field at time = 1.02 s is [tex]B_t = 2.60 \ T[/tex]
The resistance is [tex]R = 2.70\ \Omega[/tex]
The induced emf is mathematically represented as
[tex]\epsilon = - N * \frac{ d\phi }{dt}[/tex]
The negative sign tells us that the induced emf is moving opposite to the change in magnetic flux
Here [tex]d\phi[/tex] is the change in magnetic flux which is mathematically represented as
[tex]d \phi = dB * A[/tex]
Where dB is the change in magnetic field which is mathematically represented as
[tex]dB = B_t - B_i[/tex]
substituting values
[tex]dB = 2.60 - 0.500[/tex]
[tex]dB = 2.1 \ T[/tex]
Thus
[tex]d \phi = 2.1 * 8.20 *10^{-4}[/tex]
[tex]d \phi = 1.722*10^{-3} \ weber[/tex]
So
[tex]|\epsilon| = 1 * \frac{ 1.722*10^{-3}}{1.02}[/tex]
[tex]|\epsilon| = 1.69 *10^{-3} \ V[/tex]
The induced current i mathematically represented as
[tex]I = \frac{\epsilon}{ R }[/tex]
substituting values
[tex]I = \frac{1.69*10^{-3}}{ 2.70 }[/tex]
[tex]I = 6.25*10^{-4} \ A[/tex]
Two spherical objects at the same altitude move with identical velocities and experience the same drag force at a time t. If Object 1 has twice (2x) the diameter of Object 2, which object has the larger drag coefficient? Explain your answer using the drag equation.
Answer:
The object with the twice the area of the other object, will have the larger drag coefficient.
Explanation:
The equation for drag force is given as
[tex]F_{D} = \frac{1}{2}pu^{2} C_{D} A[/tex]
where [tex]F_{D}[/tex] IS the drag force on the object
p = density of the fluid through which the object moves
u = relative velocity of the object through the fluid
p = density of the fluid
[tex]C_{D}[/tex] = coefficient of drag
A = area of the object
Note that [tex]C_{D}[/tex] is a dimensionless coefficient related to the object's geometry and taking into account both skin friction and form drag. The most interesting things is that it is dependent on the linear dimension, which means that it will vary directly with the change in diameter of the fluid
The above equation can also be broken down as
[tex]F_{D}[/tex] ∝ [tex]P_{D}[/tex] A
where [tex]P_{D}[/tex] is the pressure exerted by the fluid on the area A
Also note that [tex]P_{D}[/tex] = [tex]\frac{1}{2}pu^{2}[/tex]
which also clarifies that the drag force is approximately proportional to the abject's area.
In this case, the object with the twice the area of the other object, will have the larger drag coefficient.
The magnetic force per meter on a wire is measured to be only 45 %% of its maximum possible value. Calculate the angle between the wire and the magnetic field.
Answer:
27°
Explanation:
The force is proportional to the sine of the angle between the wire and the magnetic field. (See the ref.)
So theta = arcsin(0.45)
=27°
The angle between the wire and the magnetic field is 27°.
Calculation of the angle:Since The magnetic force per meter on a wire is measured to be only 45 %
So here we know that The force should be proportional to the sine of the angle between the wire and the magnetic field
Therefore,
theta = arcsin(0.45)
=27°
Hence, The angle between the wire and the magnetic field is 27°.
Learn more about wire here: https://brainly.com/question/24733137
gravity can be described as..?
A. an magnetic force found in nature
B.the force that moves electrical charges
C.the force that repels object with like chargers
D.the force of attraction between two objects
Answer:
D
Explanation:
Gravity is the force of attraction between two objects.
Each object creates a gravitational field in wich every other object is affected by it.
What is the wave length if the distance from the central bright region to the sixth dark fringe is 1.9 cm . Answer in units of nm.
Complete Question
The complete question is shown on the first uploaded image
Answer:
The wavelength is [tex]\lambda = 622 nm[/tex]
Explanation:
From the question we are told that
The distance of the slit to the screen is [tex]D = 5 \ m[/tex]
The order of the fringe is m = 6
The distance between the slit is [tex]d = 0.9 \ mm = 0.9 *10^{-3} \ m[/tex]
The fringe distance is [tex]Y = 1.9 \ cm = 0.019 \ m[/tex]
Generally the for a dark fringe the fringe distance is mathematically represented as
[tex]Y = \frac{[2m - 1 ] * \lambda * D }{2d}[/tex]
=> [tex]\lambda = \frac{Y * 2 * d }{[2*m - 1] * D}[/tex]
substituting values
=> [tex]\lambda = \frac{0.019 * 2 * 0.9*10^{-3} }{[2*6 - 1] * 5}[/tex]
=> [tex]\lambda = 6.22 *10^{-7} \ m[/tex]
[tex]\lambda = 622 nm[/tex]
A Young'sdouble-slit interference experiment is performed with monochromatic light. The separation between the slits is 0.44 mm. The interference pattern on the screen 4.2 m away shows the first maximum 5.5 mm from the center of the pattern. What is the wavelength of the light in nm
Answer:
Explanation:
The double slit interference phonemene is described for the case of constructive interference
d sin θ= m λ (1)
let's use trigonometry to find the sinus
tan θ = y / L
in general in interference phenomena the angles are small
tan θ = sin θ / cos θ = sin θ
The double slit interference phonemene is described for the case of constructive interference
d sin θ = m lam (1)
let's use trigonometry to find the sinus
tan θ = y / L
in general in interference phenomena the angles are small
tan θ = sin θ / cos θ = sin θ
we substitute
sin θ = y / L
we substitute in equation 1
d y / L = m λ
λ = dy / L m
let's reduce the magnitudes to the SI system
d = 0.44 mm = 0.44 10⁻³ m
y = 5.5 mm = 5.5 10⁻³ m
L = 4.2m
m = 1
let's calculate
λ = 0.44 10⁻³ 5.5 10⁻³ / (4.2 1)
λ = 5.76190 10-7 m
let's reduce to num
lam = 5.56190 10-7 m (109 nm / 1m)
lam = 556,190 nmtea
we substitute
without tea = y / L
we substitute in equation 1
d y / L = m lam
lam = dy / L m
let's reduce the magnitudes to the SI system
d = 0.44 me = 0.44 10-3 m
y = 5.5 mm = 5.5 10-3
L = 4.2m
m = 1
let's calculate
lam = 0.44 10⁻³ 5.5 10⁻³ / (4.2 1)
lam = 5.76190 10⁻⁷ m
let's reduce to num
lam = 5.56190 10⁻⁷ m (109 nm / 1m)
lam = 556,190 nm
"Neon signs need 12,000 V to operate. If a transformer operates off a 240 V source and has 1000 turns in its primary coil, how may turns must the secondary coil have
Answer:
50000 turns
Explanation:
Vp / Vs = Np / Ns
240 / 12000 = 1000 / Ns
Ns = 50000 turns
The number of neutrons in the nucleus of zinc 65 Zn 30 is:
35
Need more data to answer
65
30
Explanation:
proton number + neutron number = atomic mass
30 + 35 = 65
A Young's interference experiment is performed with blue-green laser light. The separation between the slits is 0.500 mm, and the screen is located 3.10 m from the slits. The first bright fringe is located 3.22 mm from the center of the interference pattern. What is the wavelength of the laser light?
Answer:
λ = 5.2 x 10⁻⁷ m = 520 nm
Explanation:
From Young's Double Slit Experiment, we know the following formula for the distance between consecutive bright fringes:
Δx = λL/d
where,
Δx = fringe spacing = distance of 1st bright fringe from center = 0.00322 m
L = Distance between slits and screen = 3.1 m
d = Separation between slits = 0.0005 m
λ = wavelength of light = ?
Therefore,
0.00322 m = λ(3.1 m)/(0.0005 m)
λ = (0.00322 m)(0.0005 m)/(3.1 m)
λ = 5.2 x 10⁻⁷ m = 520 nm
A wooden artifact from a Chinese temple has a 14C activity of 41.0 counts per minute as compared with an activity of 58.2 counts per minute for a standard of zero age. You may want to reference (Pages 913 - 916) Section 21.4 while completing this problem. Part A From the half-life for 14C decay, 5715 yr, determine the age of the artifact. Express your answer using two significant figures. t
Answer:
Explanation:
The relation between activity and number of radioactive atom in the sample is as follows
dN / dt = λ N where λ is disintegration constant and N is number of radioactive atoms
For the beginning period
dN₀ / dt = λ N₀
58.2 = λ N₀
similarly
41 = λ N
dividing
58.2 / 41 = N₀ / N
N = N₀ x .70446
formula of radioactive decay
[tex]N=N_0e^{-\lambda t }[/tex]
[tex].70446 =e^{-\lambda t }[/tex]
- λ t = ln .70446 = - .35
t = .35 / λ
λ = .693 / half life
= .693 / 5715
= .00012126
t = .35 / .00012126
= 2886.36
= 2900 years ( rounding it in two significant figures )
21. What is the most likely outcome of decreasing the frequency of incident light on a diffraction grating?
A. lines become narrower
B. distance between lines increases
C. lines become thicker
D. distance between lines decreases
Answer:
B.distance between lines increases
Answer:
A. Lines become narrower
Explanation:
I got it right on my quiz!
I hope this helps!! :))
An appliance with a 20.0-2 resistor has a power rating of 15.0 W. Find the maximum current which can flow safely through the appliance g
Q: An appliance with a 20 Ω resistor has a power rating of 15.0 W. Find the maximum current which can flow safely through the appliance g
Answer:
0.866 A
Explanation:
From the question,
P = I²R............................. Equation 1
Where P = power, I = maximum current, R = Resistance.
Make I the subject of the equation
I = √(P/R).................... Equation 2
Given: P = 15 W, R = 20 Ω
Substitute these values into equation 2
I = √(15/20)
I = √(0.75)
I = 0.866 A
Hence the maximum current that can flow safely through the appliance = 0.866 A
To work on your car at night, you use an extension cord to connect your work light to a power outlet near the door. How would the illumination provided by the light be affected by the length of the extension cord
Answer:
The longer the cord, the lower the illumination
Explanation:
The illumination provided by the light bulb will be reduced as the length of the extension cord increases. This is because the resistance provided by the wire increases with its length.
Long wires have more electrical resistance than shorter ones.
Let us consider this formula:
Resistance =[tex]\frac{\rho L}{A}[/tex]
From this formula, we can see that as the length increases, the resistance to current flow offered by the wire increases also provided the resistivity and cross-sectional area of the wire remain constant. As a result of this, the illumination will drop.
A segment of wire of total length 3.0 m carries a 15-A current and is formed into a semicircle. Determine the magnitude of the magnetic field at the center of the circle along which the wire is placed.
Answer:
4.9x10^-6T
Explanation:
See attached file
A tennis player swings her 1000 g racket with a speed of 12 m/s. She hits a 60 g tennis ball that was approaching her at a speed of 15 m/s. The ball rebounds at 40 m/s.
A) How fast is her racket moving immediately after the impact? You can ignore the interaction of the racket with her hand for the brief duration of the collision.
_________m/s
B) If the tennis ball and racket are in contact for 7.00, what is the average force that the racket exerts on the ball?
_________N
The velocity and force are required.
The speed of the racket is 8.7 m/s
The required force is 471.43 N.
[tex]m_1[/tex] = Mass of racket = 1000 g
[tex]m_2[/tex] = Mass of ball = 60 g
[tex]u_1[/tex] = Initial velocity of racket = 12 m/s
[tex]u_2[/tex] = Initial velocity of ball = -15 m/s
[tex]v_1[/tex] = Final velocity of racket
[tex]v_2[/tex] = Final velocity of ball = 40 m/s
[tex]\Delta t[/tex] = Time = 7 ms
The equation of the momentum will be
[tex]m_1u_1+m_2u_2=m_1v_1+m_2v_2\\\Rightarrow v_1=\dfrac{m_1u_1+m_2u_2-m_2v_2}{m_1}\\\Rightarrow v_1=\dfrac{1\times 12+0.06\times (-15)-0.06\times 40}{1}\\\Rightarrow v_1=8.7\ \text{m/s}[/tex]
Force is given by
[tex]F=m_2\dfrac{v_2-u_2}{\Delta t}\\\Rightarrow F=0.06\times \dfrac{40-(-15)}{7\times 10^{-3}}\\\Rightarrow F=471.43\ \text{N}[/tex]
Learn more:
https://brainly.com/question/19689434?referrer=searchResults
A charge is placed on a spherical conductor of radius r1. This sphere is then connected to a distant sphere of radius r2 (not equal to r1) by a conducting wire. After the charges on the spheres are in equilibrium:__________.
1. the electric fields at the surfaces of the two spheres are equal.
2. the amount of charge on each sphere is q/2.
3. both spheres are at the same potential. the potentials are in the ratio V2/V1 = q2/q1.
4. the potentials are in the ratio V2/V1 = r2/r1 .
Answer:
Option 3 = both spheres are at the same potential.
Explanation:
So, let us complete or fill the missing gap in the question above;
" A charge is placed on a spherical conductor of radius r1. This sphere is then connected to a distant sphere of radius r2 (not equal to r1) by a conducting wire. After the charges on the spheres are in equilibrium BOTH SPHERES ARE AT THE SAME POTENTIAL"
The reason both spheres are at the same potential after the charges on the spheres are in equilibrium is given below:
=> So, if we take a look at the Question again, the kind of connection described in the question above (that is a charged sphere, say X is connected another charged sphere, say Y by a conducting wire) will eventually cause the movement of charges(which initially are not of the same potential) from X to Y and from Y to X and this will continue until both spheres are at the same potential.
Unpolarized light passes through a vertical polarizing filter, emerging with an intensity I0. The light then passes through a horizontal filter, which blocks all of the light; the intensity transmitted through the pair of filters is zero. Suppose a third polarizer with axis 45 ? from vertical is inserted between the first two.
What is the transmitted intensity now?
Express your answer in terms of I0. I got I0/8. But this is not right. I guess they want a number?
Answer:
I₂ = 0.25 I₀
Explanation:
To know the light transmitted by a filter we must use the law of Malus
I = I₀ cos² θ
In this case, the intensity of the light that passes through the first polarizer is I₀, it reaches the second polarized, which is at 45⁰, therefore the intensity I1 comes out of it.
I₁ = I₀ cos² 45
I₁ = I₀ 0.5
this is the light that reaches the third polarizer, which is at 45⁰ with respect to the second, from this comes the intensity I₂
I₂ = I₁ cos² 45
I₂ = (I₀ 0.5) 0.5
I₂ = 0.25 I₀
this is the intensity of the light transmitted by the set of polarizers
What is the change in internal energy of the system (∆U) in a process in which 10 kJ of heat energy is absorbed by the system and 70 kJ of work is done by the system?
Answer:
Explanation:
According to first law of thermodynamics:
∆U= q + w
= 10kj+(-70kJ)
-60kJ
, w = + 70 kJ
(work done on the system is positive)
q = -10kJ ( heat is given out, so negative)
∆U = -10 + (+70) = +60 kJ
Thus, the internal energy of the system decreases by 60 kJ.
Experts, ACE, Genius... can anybody calculate for the Reactions at supports A and B please? Will give brainliest! Given: fb = 300 kN/m, fc = 100 kN/m, Dy = 300 kN, spanAB = 6m, span BC = 6m, spanCD = 6m
Answer:
Support at Cy = 1.3 x 10³ k-N
Support at Ay = 200 k-N
Explanation:
given:
fb = 300 k-N/m
fc = 100 k-N/m
D = 300 k-N
L ab = 6 m
L bc = 6 m
L cd = 6 m
To get the reaction A or C.
take summation of moment either A or C.
Support Cy:
∑ M at Ay = 0
(( x1 * F ) + ( D * Lab ) + ( D * L bc + D * L cd )
Cy = -------------------------------------------------------------------
( L ab + L bc )
Cy = 1.3 x 10³ k-N
Support Ay:
Since ∑ F = 0, A + C - F - D = 0
A = F + D - C
Ay = 200 k-N
Answer:
i was going to but its to late
Explanation:
An electron traveling with a speed v enters a uniform magnetic field directed perpendicular to its path. The electron travels for a time t0 along a half-circle of radius R before leaving the magnetic field traveling opposite the direction it initially entered the field. Which of the following quantities would change if the electron had entered the field with a speed 2v? (There may be more than one correct answer.)
a. The radius of the circular path the electron travels
b. The magnitude of the electron's acceleration inside the field
c. The time the electron is in the magnetic field
d. The magnitude of the net force acting on the electron inside the field
Answer:
Explanation:
For circular path in magnetic field
mv² / R = Bqv ,
m is mass , v is velocity , R is radius of circular path , B is magnetic field , q is charge on the particle .
a )
R = mv / Bq
If v is changed to 2v , keeping other factors unchanged , R will be doubled
b )
magnitude of acceleration inside field
= v² / R
= Bqv / m
As v is doubled , acceleration will also be doubled
c )
If T be the time inside the magnetic field
T = π R / v
= π / v x mv / Bq
= π m / Bq
As is does not contain v that means T remains unchanged .
d )
Net force acting on electron
= m v² / R = Bqv
Net force = Bqv
As v becomes twice force too becomes twice .
So a . b , d are correct answer.
On a part-time job, you are asked to bring a cylindrical iron rod of density 7800 kg/m 3 kg/m3 , length 81.2 cmcm and diameter 2.60 cmcm from a storage room to a machinist. Calculate the weight of the rod, www. Assume the free-fall acceleration is ggg = 9.80 m/s2m/s2 .
Answer:
The weight of the rod is 32.87 N
Explanation:
Density of the rod = 7800 kg/m
length of the rod = 81.2 cm = 0.812 m
diameter of rod = 2.60 cm = 0.026 m
acceleration due to gravity = 9.80 m/s^2
The rod can be assumed to be a cylinder.
The volume of the rod can be calculated as that of a cylinder, and can be gotten as
V = [tex]\frac{\pi d^{2} l}{4}[/tex]
where d is the diameter of the rod
l is the length of the rod
V = [tex]\frac{3.142* 0.026^{2}* 0.812}{4}[/tex] = 4.3 x 10^-4 m^3
We know that the mass of a substance is the density times the volume i.e
mass m = ρV
where ρ is the density of the rod
V is the volume of the rod
m = 4.3 x 10^-4 x 7800 = 3.354 kg
The weight of a substance is the mass times the acceleration due to gravity
W = mg
where g is the acceleration due to gravity g = 9.80 m/s^2
The weight of the rod W = 3.354 x 9.80 = 32.87 N
A record player rotates a record at 45 revolutions per minute. When the record player is switched off, it makes 4.0 complete turns at a constant angular acceleration before coming to rest. What was the magnitude of the angular acceleration (in rads/s2) of the record as it slowed down
Answer:
The angular acceleration is [tex]\alpha = 0.4418 \ rad /s^2[/tex]
Explanation:
From the question we are told that
The angular speed is [tex]w_f = 45 \ rev / minutes = \frac{45 * 2 * \pi }{60 }= 4.713 \ rad/s[/tex]
The angular displacement is [tex]\theta =4 \ rev = 4 * 2 * \pi = 25.14 \ rad[/tex]
From the first equation of motion we can define the movement of the record as
[tex]w_f ^2 = w_o ^2 + 2 * \alpha * \theta[/tex]
Given that the record started from rest [tex]w_o = 0[/tex]
So
[tex]4.713^2 = 2 * \alpha * 25.14[/tex]
[tex]\alpha = 0.4418 \ rad /s^2[/tex]
Two point charges of +2.0 μC and -6.0 μC are located on the x-axis at x = -1.0 cm and x 12) = +2.0 cm respectively. Where should a third charge of +3.0-μC be placed on the +x-axis so that the potential at the origin is equal to zero?
Answer:
x = 0.006 m
Explanation:
The potential at one point is given by
V = k ∑ [tex]q_{i} / r_{i}[/tex]
remember that the potential is to scale, let's apply to our case
V = k (q₁ / x₁ + q₂ / x₂ + q₃ / x)
in this case they indicate that the potential is zero
0 = k (2 10⁻⁶ / (- 1 10⁻²) + (-6 10⁻⁶) / 2 10⁻² + 3 10⁻⁶ / x)
3 / x = + 2 / 10⁻² + 3 / 10⁻²
3 / x = 500
x = 3/500
x = 0.006 m
An electron moves to the left along the plane of the page, while a uniform magnetic field points into the page. What direction does the force act on the moving electron
Answer:
acting force is the answer
The direction of the magnetic force on the moving electron is upward.
The direction of the magnetic force on the electron can be determined by applying right hand rule.
This rule states that when the thumb is held perpendicular to the fingers, the thumb will point in the direction of the speed while the fingers will point in the direction of the field and the magnetic force will be perpendicular to the field.
Thus, we can conclude that, the direction of the magnetic force on the moving electron is upward.
Learn more here:https://brainly.com/question/14434299
A 285-kg object and a 585-kg object are separated by 4.30 m. (a) Find the magnitude of the net gravitational force exerted by these objects on a 42.0-kg object placed midway between them.
Answer:
The magnitude of the net gravitational force exerted by these objects on a 42.0-kg object is 1.818 x 10⁻⁷ N
Explanation:
Given;
first object with mass, m₁ = 285 kg
second object with mass, m₂ = 585 kg
distance between the two objects, r = 4.3 m
The midpoint between the two objects = r/₂ = 4.3 /2 = 2.15 m
Gravitational force between the first object and the 42 kg object;
[tex]F = \frac{GMm}{r^2}[/tex]
where;
G = 6.67 x 10⁻¹¹ Nm²kg⁻²
[tex]F = \frac{6.67*10^{-11} *285*42}{2.15^2} \\\\F = 1.727*10^{-7} \ N[/tex]
Gravitational force between the second object and the 42 kg object
[tex]F = \frac{6.67*10^{-11} *585*42}{2.15^2} \\\\F = 3.545*10^{-7} \ N[/tex]
Magnitude of net gravitational force exerted on 42kg object;
F = 3.545x 10⁻⁷ N - 1.727 x 10⁻⁷ N
F = 1.818 x 10⁻⁷ N
Therefore, the magnitude of the net gravitational force exerted by these objects on a 42.0-kg object is 1.818 x 10⁻⁷ N
A computer has a mass of 3 kg. What is the weight of the computer?
A. 288 N.
B. 77.2 N
C. 3N
D. 29.4 N
Answer:
29.4 NOption D is the correct option.
Explanation:
Given,
Mass ( m ) = 3 kg
Acceleration due to gravity ( g ) = 9.8 m/s²
Weight ( w ) = ?
Now, let's find the weight :
[tex]w \: = \: m \times g[/tex]
plug the values
[tex] = 3 \times 9.8[/tex]
Multiply the numbers
[tex] = 29.4 \: [/tex] Newton
Hope this helps!!
best regards!!
Two metal sphere each of radius 2.0 cm, have a center-to-center separation of 3.30 m. Sphere 1 has a chrage of +1.10 10^-8 C. Sphere 2 has charge of -3.60 10^-8C. Assume that the separation is large enough for us to assume that the charge on each sphere iss uniformly distribuuted.
A) Calculate the potential at the point halfway between the centers.
B) Calculate the potential on the surface of sphere 1.
C) Calculate the potential on the surface of sphere 2.
Answer:
A) V = -136.36 V , B) V = 4.85 10³ V , C) V = 1.62 10⁴ V
Explanation:
To calculate the potential at an external point of the spheres we use Gauss's law that the charge can be considered at the center of the sphere, therefore the potential for an external point is
V = k ∑ [tex]q_{i} / r_{i}[/tex]
where [tex]q_{i}[/tex] and [tex]r_{i}[/tex] are the loads and the point distances.
A) We apply this equation to our case
V = k (q₁ / r₁ + q₂ / r₂)
They ask us for the potential at the midpoint of separation
r = 3.30 / 2 = 1.65 m
this distance is much greater than the radius of the spheres
let's calculate
V = 9 10⁹ (1.1 10⁻⁸ / 1.65 + (-3.6 10⁻⁸) / 1.65)
V = 9 10¹ / 1.65 (1.10 - 3.60)
V = -136.36 V
B) The potential at the surface sphere A
r₂ is the distance of sphere B above the surface of sphere A
r₂ = 3.30 -0.02 = 3.28 m
r₁ = 0.02 m
we calculate
V = 9 10⁹ (1.1 10⁻⁸ / 0.02 - 3.6 10⁻⁸ / 3.28)
V = 9 10¹ (55 - 1,098)
V = 4.85 10³ V
C) The potential on the surface of sphere B
r₂ = 0.02 m
r₁ = 3.3 -0.02 = 3.28 m
V = 9 10⁹ (1.10 10⁻⁸ / 3.28 - 3.6 10⁻⁸ / 0.02)
V = 9 10¹ (0.335 - 180)
V = 1.62 10⁴ V
The 2-Mg truck is traveling at 15 m/s when the brakes on all its wheels are applied, causing it to skid for 10 m before coming to rest. The total mass of the boat and trailer is 1 Mg. Determine the constant horizontal force developed in the coupling C, and the friction force developed between the tires of the truck and the road during this time.
Answer:
constant horizontal force developed in the coupling C = 11.25KN
the friction force developed between the tires of the truck and the road during this time is 33.75KN
Explanation:
See attached file
The friction force between the tires of the truck and the road is 22500 N.
Calculating the friction force:It is given that a 2 Mg truck ( m = 2000 Kg) is initially moving with a speed of u = 15 m/s.
Distance traveled before coming to rest, s = 10m
The final velocity of the truck will be zero, v = 0
When the breaks are applied, only the frictional force is acting on the truck and it is opposite to the motion of the truck.
The frictional force is given by:
f = -ma
the acceleration of the truck = -a
The negative sign indicates that the acceleration is opposite to the motion.
Applying the third equation of motion we get:
v² = u² -2as
0 = 15² - 2×a×10
225 = 20a
a = 11.25 m/s²
So the magnitude of frictional force is:
f = ma = 2000 × 11.25 N
f = 22500 N
Learn more about friction force:
https://brainly.com/question/1714663?referrer=searchResults