Answer:
It’s like medium uk
Explanation:
The size of electron charge is estimated to be 1.6 × 10-¹⁹
plsss helpp i really need this now thank u ❤️
Answer:
10.
parabolic
11.
Entirely horizontal
12.
45°
Which of the following statements explains how total time spent in the air is affected as a projectile's angle of launch is increased from 25 degrees to 50 degrees?
Answer:
Therefore letter C is the correct answer.
Explanation:
In a projectile motion the total time in the air can be calculated using the following equation:
We analyze the y-component motion.
[tex]v_{fy}=v_{iy}-gt[/tex]
When the final velocity (v(f)) is equal to zero we calculate the upward time and multiplying it by 2 we find the total time in the air. So we will have:
[tex]t_{tot}=2\frac{v_{iy}}{g}[/tex]
[tex]t_{tot}=2\frac{v_{i}sin(\theta)}{g}[/tex]
We can see that the total time is directly proportional to the angle, then when θ increase t increase.
Therefore letter C is the correct answer.
I hope it helps you!
Jorge tightens a bolt on his bicycle with a wrench that is 0.20 m long. If he pulls perpendicularly on the end of the wrench with a force of 140 N, how much torque does he apply ?
Answer:
28Nm
Explanation:
Torque is expressed as the prduct of force and radius
Given
Force = 140N
radius = 0.20m
Torque = 140 * 0.2
Torque = 140 * 1/5
Torque = 28Nm
Hence the amouunt of torque applied is 28Nm
what is a product made from no renewable resources
Answer:
a nail
Explanation:
Answer:
crude oil, natural gas, coal, and uranium. These are all resources that are processed into products that can be used commercially.
Explanation:
A parallel combination of 3ohms and 4ohms resistor is connected in series with a resistor of 4ohms and a battery of negligible resistance. Calculate the effective resistance in the circuit
Answer:
Explanation:
Equivalent resistance of parallel combination of two resistors of 3 ohms and 4 ohms .
R₁ = 3 x 4 / ( 3 + 4 )
= 12 / 7 = 1.7 ohms .
This equivalent resistance is connected with 4 ohms in series
Total resistance = 1.7 ohms + 4 ohms
= 5.7 ohms.
Hence effective resistance of the circuit = 5.7 ohms .
A 330.-ohm resistor is connected to a 5.00-volt battery. What is the current through the resistor?
Answer:
From Ohms Law
V=IR
V=5volts
R=33.0hms
I=V/R
I= 5/330
=0.0152A
The current flowing through the cross-section of the resistor is 0.0152A.
Given the data in the question;
Resistance; [tex]R = 330ohm[/tex]Voltage; [tex]V = 5.00V[/tex]Current; [tex]I = \ ?[/tex]Ohm's lawOhm's law states that "the current flowing through the cross-section of a conductor is directly proportional to the voltage across it".
It is expressed as;
[tex]V = IR[/tex]
Where V is voltage, I is current and R is the Resistance.
To determine the current flowing through the resistor, we substitute our given values into the expression above.
[tex]V = IR\\\\I = \frac{V}{R}\\ \\I = \frac{5.00V}{330\ Ohm} \\\\I = 0.0152A[/tex]
Therefore, the current flowing through the cross-section of the resistor is 0.0152A.
Learn more about Electric current here: https://brainly.com/question/2264542
What are some core features of waves in physics?
Answer:
Waves are disorders that travel through a fluid medium. Several simple wave features include frequency, period, wavelength, and amplitude.
Explanation:
What if the World turned to Gold?
Answer:
We would all freeze at close to absolute zero and gold will not be worth anything
Explanation:
A star produces energy by:
A: creating helium from hydrogen in its core.
B: reflecting energy from nearby stars.
C: absorbing and releasing the matter of other stars.
D: rotating quickly on its axis.
Here, the hydrogen atoms are combined to form a helium atom, and during this process of fusion, a significantly large amount of energy is released. Thus, stars produce a large amount of energy by forming helium from the combination of hydrogen in its core. Hence, the correct answer is option (C).
Answer:
A. Creating helium from hydrogen in its core.
Explanation:
Sacrificed my grade for points I hope it helps
In a physics lab, Ray Zuvlite arranges two mirrors with a right angle orientation as shown. Ray then directs a laser line at one of the mirrors. The light reflects off both mirrors as shown. If angle A is 25°, determine the what is the angle measure of angles B, C, and D?
Answer:
B = 25°
C = 65°
D = 25°
Explanation:
The given parameters are;
The orientation of the two mirrors = At right angle to each other
The laser light is directed at one of the mirror
The measure of angle, A = 25°
The measures of angle B, C, and D are found as follows;
We have;
∠A = ∠B = 25°, by angle of incidence equals angle of reflection
∠B = 25°
∠B + ∠C = 90° by sum of the acute angles of a right triangle
25° + ∠C = 90°
∴ ∠C = 90° - 25° = 65°
∠C = 65°
∠E = ∠C = 65° by angle of incidence equals angle of reflection
∴ ∠E = 65°
Line 'L' is perpendicular to the second mirror, therefore, the angle between line 'L' and the second mirror = 90° = ∠E + ∠D
∠E + ∠D = 90°, by angle sum property
Therefore;
65° + ∠D = 90°
∴ ∠D = 90° - 65° = 25°
∠D = 25°
The length of a planet's day is determined by it's
Answer: "People will say the length of a day is determined by just the rotation rate of a planet, but that isn’t entirely true. The orbit around its sun also factors in. What we define as a day is the time between when the Sun is highest in the sky until the next time the Sun is at the highest point in the sky. This isn’t just the time it takes the Earth to rotate once on its axis, though. This is because, as the Earth is rotating, it’s also moving relative to the Sun"
Usain bolt ran the 200m race within 19.19 seconds. Calculate the speed of Usain bolt during the race
Answer: [tex]10.42\ m/s[/tex]
Explanation:
Given
Usain Bolt ran the race with a length [tex]200\ m[/tex]
Time is taken to complete it [tex]t=19.19\ s[/tex]
We know, [tex]\text{Distance}=\text{speed}\times \text{time}[/tex]
Insert the values
[tex]\Rightarrow 200=v\times 19.19\\\\\Rightarrow v=\dfrac{200}{19.19}\\\\\Rightarrow v=10.42\ m/s[/tex]
So, the speed of Usain Bolt is [tex]10.42\ m/s[/tex]
Which term BEST describes energy
stored in batteries and food?
potential energy
kinetic energy
heat energy
chemical energy
ik its a lot but can u help
Answer:
your correct ans is D.
object float in liquid when its density is less than liquid and sinks when its density is more than liquid..
stay safe healthy and happy.Einstein's theory of general relativity is currently the best explanation of gravity.Why has this theory not been replaced with a new one
Answer:
Option C, It still explains the experimental evidence pertaining to gravity
Explanation:
Please find the attachment
Answer:
A.) It will remain the best explanation, because no one has come up with a better one yet
Explanation:
A nucleus with mass number 229 emits a 3.443 MeV alpha particle. Calculate the disintegration energy Q for this process, taking the recoil energy of the residual nucleus into account.
Answer:
3.504 MeV
Explanation:
Given that;[tex]\frac{A}{Z} X ---->\frac{A-4}{Z-2} Y +\alpha + Q[/tex]
Also;
[tex]Q= KE_{\alpha } (M_{Y} + M_{\alpha } /M_{Y[/tex])
Mass number of X = 229
Mass number of Y = 225
Mass number of alpha particles = 4
Kinetic energy of alpha particles = 3.443 MeV
Q = 3.443 MeV (225 + 4/225)
Q= 3.504 MeV
A positive charge is moving across a room from south to north. A magnetic field runs from east to west. In what direction is the magnetic force on the moving positive charge?
Answer:
the force is on the z axis, coming out of the blade
Explanation:
The direction of the magnetic force is given by the right hand rule,
For a positive charge, the thumb points in the direction of velocity, the other fingers extended in the direction of the magnetic field, and the palm points in the direction of force.
In this case.
Thumb points North
The fingers extended is in the east - west direction parallel to the blade
The palm is sticking out of the leaf, in the z direction
the answer is the force is on the z axis, coming out of the blade
If 150 Joules of work is needed to move a box 1000 cm, calculate the force that was used?
Answer:
[tex] \large{ \tt{☄ EXPLANATION}} : [/tex]
We're provided : Work ( W ) = 150 J & Displacement ( D ) = 1000 cm & We're asked to find out the force that was used. Firstly, Notice that we're provided the unit of Displacement as centimetre so we have to convert 1000 cm into m. Displacement ( D ) = [tex] \frac{1000}{ 100} = 10[/tex] m[tex] \large{ \tt{♡ \: LET'S \: GET \: STARTED}} : [/tex]
Work is defined as the product of force and Displacement. By definition ,[tex] \large{ \boxed{ \tt{❃ \: WORK ( \: W \: ) = FORCE\: ( \: F) \times DISPLACEMENT \: ( \: D \: )}}}[/tex]
- Plug the values and then simplify !
[tex] \large{ \bf{↦ \: 150 = F \times 10}}[/tex]
[tex] \large{ \bf{↦F\times 10 = 150}}[/tex]
[tex] \large{ \bf{↦ \: F = \frac{150}{10}}} [/tex]
[tex] \large {\bf{↦F = \boxed{ \bf{15} \: N}}}[/tex]
[tex] \boxed{ \boxed{ \large{ \tt{✤ \: OUR \: FINAL \: ANSWER : \boxed{ \bf{15 \: n}}}}}}[/tex]
KEEP READING , KEEP STUDYING , KEEP WORKING , KEEP PUSHING , KEEP TAKING CARE OF YOURSELF. YOUR HARD WORK WILL PAY OFF ! ♪ツ Hope I helped ! ۵
☪ Have a wonderful day / evening ! ☼
# StayInAndExplore ! ☂
▁▁▁▁▁▁▁▁▁▁▁▁▁▁▁▁▁▁▁▁▁
A beam strikes an irregular mirror and is reflected as shown below. The angle formed by the incoming beam and the reflected beam is 10 degrees. What is the angle of the mirror's surface (measured against vertical) at the location where the beam strikes the mirror?
A. The mirror's surface is angled 5 degrees upward where the laser strikes it.
B. The mirror's surface is angled 5 degrees downward where the laser strikes it.
C. The mirror's surface is angled 10 degrees upward where the laser strikes it.
D. The mirror's surface is angled 10 degrees downward where the laser strikes it.
Answer:
the correct answer is B
Explanation:
The law of reflection states that the angles of incidence and reflection on a surface are the same, the two rays and the normal are in the same part of the surface.
In this exercise indicate that the angle between the incident and reflected ray is 10, therefore the angle with respect to the normal that is a vertical line at the point of contact of the ray must be 5
Consequently the correct answer is B
3. How do energy transformations, energy transfers, and conservation of energy allows you to track how energy moves through in a system?
Answer:
The law of conservation of energy states that when one form of energy is transformed to another, no energy is destroyed in the process. According to the law of conservation of energy, energy cannot be created or destroyed. So the total amount of energy is the same before and after any transformation
Explanation:
The energy in a system always transforms from one form to another without any significant loss or addition. It simply changes from one form to another with the effect of numerous external influences.
What is Energy transformation?Energy transformation may be defined as the process through which energy can convert from one form to another. It also illustrates the migration of energy from one place to another due to physical factors.
According to the law of conservation of energy, in a closed system energy can neither be created nor destroyed. The total amount of energy remains the same before and after the process of transformation.
Therefore, the energy in a system always transforms from one form to another without any significant loss or addition.
To learn more about Energy transformations, refer to the link:
https://brainly.com/question/16917873
#SPJ2
A net force of 60 N north acts on an object with a mass of 30 kg. Use Newton's second law of
motion to calculate the amount of acceleration the object will experience. Then explain how the
amount of acceleration will change if the net force or the mass of the object increases.
Answer:
Explanation:
F = ma. For us, this looks like
60 = 30a and
a = 2 m/s/s
If the force goes up to, say, 90, then
90 = 30a and
a = 3...if the force goes up, the acceleration also goes up.
If the mass goes up to say, 60, and the force stays the same, then
60 = 60a and
a = 1...if the mass goes up, the acceleration goes down.
the degree of hotness and coldness of th body is.......
Answer:
Explanation:
The degree of hotness and coldness of the body is called temperature.
Does a feather fall as fast as a rock in a vacuum? If so why?
Answer:
No.
Explanation:
A feather is less dense and thus less force exerted while a rock is very dense thus exerting more force .
20 POINTS:
Why does the initial hill of a roller coaster need to be steep?
Answer: A roller coaster does not have an engine to generate energy. The climb up the first hill is accomplished by a lift or cable that pulls the train up. This builds up a supply of potential energy that will be used to go down the hill as the train is pulled by gravity
Hope this helps! Good luck with future homework and exams!
A 4kg and 5kg bodies moving on a frictionless horizontal surface at a velocity of ( -6i )m/s and ( +3 )m/s respectively. Collide a head on elastic collision. What is the velocity ( magnitude and direction) of the each body after collision?
Answer:
4 kg → +4 m/s
5 kg → -5 m/s
Explanation:
The law of conservation of momentum states that:
m₁v₁ + m₂v₂ = m₁v₁' + m₂v₂'left side → velocities before collisionright side → velocities after collisionYou'll notice that we have two missing variables: v₁' & v₂'. Assuming this is a perfectly elastic collision, we can use the conservation of kinetic energy to set the initial and final velocities of the individual bodies equal to each other.
v₁ + v₁' = v₂ + v₂'Let's substitute all known variables into the first equation.
(4)(-6) + (5)(3) = (4)v₁' + (5)v₂' -24 + 15 = 4v₁' + 5v₂' -9 = 4v₁' + 5v₂'Let's substitute the known variables into the second equation.
(-6) + v₁' = (3) + v₂' -9 = -v₁' + v₂' 9 = v₁' - v₂'Now we have a system of equations where we can solve for v₁ and v₂.
-9 = 4v₁' + 5v₂' 9 = v₁' - v₂'Use the elimination method and multiply the bottom equation by -4.
-9 = 4v₁' + 5v₂' -36 = -4v₁' + 4v₂'Add the equations together.
-45 = 9v₂'-5 = v₂'The final velocity of the second body (5 kg) is -5 m/s. Substitute this value into one of the equations in the system to find v₁.
9 = v₁' - v₂'9 = v₁' - (-5) 9 = v₁' + 5 4 = v₁'The final velocity of the first body (4 kg) is 4 m/s.
We can verify our answer by making sure that the law of conservation of momentum is followed.
m₁v₁ + m₂v₂ = m₁v₁' + m₂v₂' (4)(-6) + (5)(3) = (4)(4) + (5)(-5)-24 + 15 = 16 - 25 -9 = -9The combined momentum of the bodies before the collision is equal to the combined momentum of the bodies after the collision. [✓]
A plane travels at an average speed of 600 kilometers per hour. How long
does it take the plane to travel 120 kilometers?
Answer:
12 mins
Explanation:
120km/600km = 1/5 or .2
60mins*0.2 = 12 mins
which of the following is a vector physical quantity
a. speed
b. energy
c. mass
d. displacement
Answer:
D. displacement
Explanation:
Vector quantities have both magnitude and direction.
Scalar quantities have only magnitude.
Two people are sitting on wheeled chairs 1 metre apart. Person A is holding a 2kg ball. Person A throws the ball to Person. What happens to person A? Explain.
a.) their chair stays still
b.) chair rolls backwards
c.) chair rolls forwards
Answer:
B - Person A's chair rolls backwards.
Explanation:
This can be seen simply through the Conservation of Momentum. When the ball is thrown to be, the ball's momentum(+m) is transfererd to B, so B's chair moves forward(think about it - it makes sense, doesn't it?), meaning A's chair moves backwards.
So, B.
EXTRA TIP: Try drawing a diagram to help you!
11. In a new science fiction movie an enemy spaceship explodes. Will an observer on a nearby
moon hear the explosion, see the explosion, or both? Explain
Answer:
Sound is transmitted by longitudinal waves thru air - the observer cannot hear the explosion because no air is present between the moon and the ship
Light is transmitted by electromagnetic waves so the light from the explosion can travel between the moon and the observer.
The point A on the above graph is an example of
extrapolation
variation
interpolation
average method
Answer:
Interpolation
Explanation:
The graph shows that it falls between 2 values and interpolation means that you estimate the unknown values that fall between the 2 values. Hope this helps!
The data point A is between two given data points and it lies within the line connecting the data points, thus we can conclude that point A is an example of interpolation.
Extrapolation is the process of extending a line connecting the data points beyond the given data points to make inferences based on the previous trend of the data set. This helps us to understand what will happen in the future if the trend continues in the same manner.
Interpolation is the process of determining an unknown variable between two known variables. In this process the data point is located within the line connecting the data points.
In this given graph, the data point A is between two given data points and it lies within the line connecting the data points, thus we can conclude that point A is an example of interpolation.
Learn more here: https://brainly.com/question/11958294