Answer:
The correct option is
a. The inductive reactance is doubled and the capacitive reactance is halved
Explanation:
For a series RLC circuit, is a resonant circuit such that the impedance, Z, is minimum at the resonance frequency
Also we have that the capacitive reactance [tex]X_C[/tex], is given as follows;
[tex]X_c = \dfrac{1}{\omega \cdot C}[/tex]
Where;
ω = Angular frequency = 2πf
Where;
f = The frequency in the circuit
[tex]\therefore X_c = \dfrac{1}{2 \cdot \pi \cdot f \cdot C}[/tex]
The inductive reactance is also given as follows;
[tex]X_L = \omega \cdot L = 2 \cdot \pi \cdot f \cdot L[/tex]
Therefore, when the circuit frequency doubles, the inductive reactance doubles and the capacitive reactance halves
When the alternating current frequency in a series RLC circuit is halved, the inductive reactance is doubled and the capacitive reactance is halved.
What is an alternating current frequency?An Alternating current (ac) frequency is known to be the amount of cycles per second that can be found in an ac sine wave.
The Frequency is known to be the rate through which the current changes direction in terms of per second. It is said to be often measured in hertz (Hz). Note that the alternating current frequency in a series RLC circuit is halved, the inductive reactance increases and the capacitive reactance is reduced.
Learn more about alternating current from
https://brainly.com/question/15595203
Please answer this question
Explanation:
m = kg. v=m/s. g=m/s^2. h= m
>>1/2mv^2=mgh
>>1/2mv^2=mgh>> kg*(m/s)^2= kg*m/s^2*m
>>1/2mv^2=mgh>> kg*(m/s)^2= kg*m/s^2*m>>kg m^2/s^2=kg m^2/s^2 the fraction 1/2 won't be able to make any changes to to the dimensional expression of energy i.e half of energy is still energy therefore you can neglect the number .
>>kg m^2/s^2=kg m^2/s^2
>>J= J
A diver releases an air bubble of volume 3.0 cm3 from a depth of 18 m below the surface of a lake, where the temperature is 9.0 ∘C. Part A What is the volume of the bubble when it reaches just below the surface of the lake, where the temperature is 22 ∘C?
Answer:
Explanation:
We shall apply gas law formula to get the solution .
P₁ V₁ / T₁ = P₂ V₂ / T₂
P₁ = 10⁵ + 18 x 10³ x 9.8 where 10⁵ Pa is atmospheric pressure at surface
= 1.764 x 10⁵ + 10⁵
= 2.764 x 10⁵
2.764 x 10⁵ x 3 / ( 273 + 9 ) = 10⁵ x V₂ / ( 273 + 22 )
V₂ = 8.67 cm³
ride and average of 15mph for 30 miles, how long does it take?
Answer:
2 hrs
Explanation:
time = distance ÷ speed
1. A note has a wavelength of 0.77955 m. If the speed of sound is 343.00 m/s, what pitch is this note? 2. A note has a wavelength of 0.52028 m. If the speed of sound is 343.00 m/s, what pitch is this note? please no funny answers
Answer:
1.) 440 Hz
2.) 659.3 Hz
Explanation:
1.) Given parameters are:
wavelength = 0.77955 m.
speed of sound = 343.00 m/s
Frequency = speed/ wavelength
Substitute speed and wavelength into the formula
Frequency = 343/ 0.77955
Frequency = 439.99
Frequency = 440 Hz approximately
2.) The parameters given are:
wavelength = 0.52028 m.
speed of sound = 343.00 m/s
Using the same formula
Frequency = speed/wavelength
Substitute all the parameters into the formula
Frequency = 343 / 0.52028
Frequency = 659.3 Hz approximately
The pitch of a note depends on the frequency of the sound waves.
The pitch of a sound increases as the frequency of the sound waves increases.
Answer:
1.) 440 Hz
2.) 659.3 Hz
Explanation:
1.) Given parameters are:
wavelength = 0.77955 m.
speed of sound = 343.00 m/s
Frequency = speed/ wavelength
Substitute speed and wavelength into the formula
Frequency = 343/ 0.77955
Frequency = 439.99
Frequency = 440 Hz approximately
2.) The parameters given are:
wavelength = 0.52028 m.
speed of sound = 343.00 m/s
Using the same formula
Frequency = speed/wavelength
Substitute all the parameters into the formula
Frequency = 343 / 0.52028
Frequency = 659.3 Hz approximately
The pitch of a note depends on the frequency of the sound waves.
The pitch of a sound increases as the frequency of the sound waves increases.
we can catch a rolling ball but not a flying bullet?? give reason
Answer:
yeah this statement is tru
Explanation:
it is because the speed of the bullet is more than the speed of rolling ball .so from this reason we cannot catch a bullet.
A bullet will be moving much faster than a rolling ball. Even seeing a bullet in flight requires it to be extremely low velocity.
The following passage has not been edited. There is an error in each line. Write the
incorrect word and the correction in your answer sheet against the correct question
number. The first one has been done as an example. ( 1 x 4 = 4 )
Community service sensitize people to Error: sensitize ; Correction: sensitizes
other‟s needs and supports inclusive (a) Error: _______ ; Correction: ______
development to the underprivileged (b) Error: _______ ; Correction: ______
sections with society. Courses about social (c) Error: ______ ; Correction: _______
work prepares frontline workers to (d) Error: _______ ; Correction: ______
Answer:
(a) Error: Other's ; Correction: Others'
(b) Error: to ; Correction: for
(c) Error: with ; Correction: of
(d) Error: prepares ; Correction: prepare
Explanation:
a) The error is in the word "other's" as the position of apostrophe is wrong, so the correct word will be "others'", it shows plural nouns.
b) The error is in the word "to", so the correct word will be "for" as for is use to talk about a purpose.
c) The error is in the word "with" and the correct word will be "of" as of indicates relationships between other words including things that made of other things.
d) The error is in the word "preapres" and the correct word will be "prepare".
Your car's 32.5 W headlight and 2.00 kW starter are ordinarily connected in parallel in a 12.0 V system. What power (in W) would one headlight and the starter consume if connected in series to a 12.0 V battery
Answer:
Explanation:
the resistance of a electrical device
R = V² / P where V is volt and P is power .
The devices are in parallel so same volt will apply on them
So R₁ = 12² / 32.5 = 4.431 ohm
R₂ = 12² / 2 x 10³ = .072 ohm
when they are in series
Common Current in them = 12 / 4.431 + .072
= 2.6649 A
power consumed by first device when they are in series
= current² x resistance
= 2.6649² x 4.431 = 31.46 W
power consumed by other
= 2.6649² x .072 = .511 W
A scientist is studying the effects of sunlight on rose bushes. Which of the
following is a testable question about this topic?
Answer:
Does more sunlight make rose bushes grow taller?
Explanation:
When conducting a research, the researcher usually poses research questions in order to confirm or disprove the research hypothesis. A research question addresses the key issues and questions that the research project is intended to answer. Good research questions always aim at improving the body of knowledge on the selected topic of the research. Research questions must be narrowed down to specific details of the topic. They must also be testable, they must not be vague.
If I am studying the effect of sunlight on rose bushes, then the question, 'does more sunlight make rose bushes grow taller?' Is apt to the research because it can be tested by exposing various thorn bush plants to varying degrees of sunlight and recording my observation.
Answer:
If rose bushes receive more hours of sunlight each day, they will grow taller.
Explanation:
I just answered it on Apex, and they like to switch up how they word things sometimes.
Two long, straight wires are parallel and 10 cm apart. One carries a current of 2.0 A, the other a current of 5.0 A. If the two currents flow in opposite directions, what is the magnitude and direction of the force per unit length of one wire on the other
Answer:
The magnitude and direction of the force per unit length of one wire on the other is 2 x 10⁻⁵ N/m, attractive force.
Explanation:
Given;
distance between the two parallel wires, r = 10 cm = 0.1 m
current in the first wire, I₁ = 2A
current in the second wire, I₂ = 5 A
The force per unit length on each wire can be calculated as;
[tex]\frac{F}{L} = \frac{\mu_oI_1I_2}{2\pi r}[/tex]
where;
μ₀ is permeability of free space = 4π x 10⁻⁷ m/A
[tex]\frac{F}{L} = \frac{\mu_oI_1I_2}{2\pi r} \\\\\frac{F}{L} = \frac{4\pi*10^{-7}*2*5}{2\pi *0.1} \\\\\frac{F}{L} = 2 *10^{-5} \ N[/tex]/ m
The direction of the force between the two wires is attractive since the current in the two wires are in opposite direction.
Therefore, the magnitude and direction of the force per unit length of one wire on the other is 2 x 10⁻⁵ N/m, attractive force.
The angle of incidence of a ray of light striking an equilateral triangular prisms ABC of refracting angle 60o is 40o. Calculate:
(i)the angle of refraction at the first face
(ii)the angle of emergence
Answer:
1: the refracted angle in the first face is equal to the incident angle that is 60degrees
2. Emergence Angle is 42degrees
Explanation:
Pls see attached file
on heating gases expand ______________ than solids and liquids
Answer:
On heating gases expands than solid and liquid because the molecules gets seperated and the volume increases that causes to expand.
Explanation:
Hope it is helpful
please mark me as brainliest
please
you (60 kg) are standing in a (500 kg) elevator that is moving upwards from a ground floor on a building what is the power rating of the motor that can lift this elevator if the elevator travels a distance of 20m upwards in 15 s
Explanation:
Power = work / time
Power = force × distance / time
P = (650 kg) (10 m/s²) (20 m) / (15 s)
P = 8667 W
If the absolute pressure inside the bottom of a container open to the atmosphere and filled with an unknown substance is 300 Pa. And the height of the container is 800.0 cm. What is the density of the substance?
Answer:
2.5 kg/m³
Explanation:
Absolute pressure = gauge pressure + atmospheric pressure
P = Pg + Pa
The gauge pressure caused by the weight of a fluid is called the static pressure. It is equal to the density of the fluid × acceleration due to gravity × depth of the fluid,
Pg = ρgh
Therefore:
P = ρgh + Pa
300 Pa = ρ (10 m/s²) (8.00 m) + 100 Pa
ρ = 2.5 kg/m³
b. i. In a hydraulic press, a force of 200N is applied to master piston of area 25cm. If
the press is designed to produce a force of 5000N, determine the area of the slave
piston.
(4marks)
Answer:
625 cm²
Explanation:
The pressure is the same on both pistons.
F/A = F/A
200 N / 25 cm² = 5000 N / A
A = 625 cm²
what nuclear fission and nuclear fusion have in common? A. They’re both used in power plants B. they have less mass than their reactants C. they start with the same reactants D. their products have more mass than their reactants
Answer:
B. they have less mass than their reactants
Explanation:
In both nuclear fission and nuclear fusion, the products have less mass than their reactants. So, option B is correct.
What is meant by nuclear reaction ?Nuclear reaction is defined as the reaction that involves the collision between one or more atomic nuclei and a highly energetic subatomic particle to produce one or more nuclei along with the emission of a large amount of energy.
Here,
Nuclear fission and fusion are two types of nuclear reactions that involves the production of large amount of energy from atomic nuclei.
Nuclear fission is the nuclear reaction in which a heavier nucleus is split into two or more lighter nuclei, under radioactive condition, with the release of a massive amount of energy.
Nuclear fusion is the nuclear reaction in which two or more lighter nuclei nuclei fuse together under radioactive condition and forms a heavier nuclei and by releasing a large amount of energy.
In both nuclear fission and nuclear fusion, there occurs a release of large amount of energy. This is because most of the mass of the reactants is converted into energy which is known as the mass-energy. So the products of these nuclear reactions will have lesser mass than their reactants.
Hence,
In both nuclear fission and nuclear fusion, the products have less mass than their reactants.
To learn more about nuclear reactions, click:
https://brainly.com/question/12786977
#SPJ3
PLEASEEE HELP, thank you :)
Answer:
The answer is B.
Explanation:
Given that the current (Ampere) in a series circuit is same so we can ignore it. We can assume that the total voltage is 60V and all the 3 resistance are different, 20Ω, 40Ω and 60Ω. So first, we have to find the total resistance by adding :
Total resistance = 20Ω + 40Ω + 60Ω
= 120Ω
Next, we have to find out that 1Ω is equal to how many voltage by dividing :
120Ω = 60V
1Ω = 60V ÷ 120
1Ω = 0.5V
Lastly, we have to calculate the voltage at R1 so we have to multiply by 20 (R1) :
1Ω = 0.5V
20Ω = 0.5V × 20
20Ω = 10V
Integrated Concepts:_______.
(a) Calculate the ratio of the highest to lowest frequencies of electromagnetic waves the eye can see, given the wavelength range of visible light is from 380 to 760 nm.
(b) Compare this with the ratio of highest (20,000 Hz) to lowest (20 Hz) frequencies the ear can hear.
a). frequency = (speed) / (wavelength)
The speed of light is around 3 x 10⁸ m/s.
For 380 nm (violet light), frequency = (3 x 10⁸ m/s) / (380 x 10⁻⁹ m)
Frequency = 7.89 x 10¹⁴ Hz
For 760 nm (red light), frequency = (3 x 10⁸ m/s) / (760 x 10⁻⁹/s)
Frequency = 3.94 x 10¹⁴ Hz
The ratio is 2 .
That's 1 octave, or 0.3 of a decade.
b). The ratio of highest/lowest sounds is (20,000 Hz/20 Hz) = 1,000
That's 3 decades, or about 10 octaves.
===> Speaking logarithmically ( ! ), ears are sensitive to a range of sound frequencies that's 10 times as wide as the range of light frequencies that eyes can detect.
2. When backing straight or to the right: a. Position your right hand on the back of the passenger seat. b. Grip the steering wheel at the 12 o’clock position with your left hand. c. Move the wheel left or right in the direction in which you want the rear of the vehicle to go. d. All of the above
Answer:
Option d = all of the above.
Explanation:
This question is more of a driving lesson or tutorial Question and not that scientific, it is logical and the "rule" attached to reversing and driving that is operating of vehicles especially cars, trucks and so on.
All the options given in the Question from option 'a' to option 'c' are all correct when driving backwards that is reversing or backing . Driving backward(backing or reversing) is not as easy as during forward (drive mode).
=> " Position your right hand on the back of the passenger seat. Grip the steering wheel at the 12 o’clock position with your left hand"
REASON: FOR BALANCING.
=> " Move the wheel left or right in the direction in which you want the rear of the vehicle to go."
The above, given in the Question are all correct.
When backing straight or to the right, all of the mentioned options are correct and recommended practices are to Position your right hand on the back of the passenger seat. The correct option is option d.
a) Position your right hand on the back of the passenger seat: This is a technique used by some drivers to help them have a better sense of the vehicle's position and reference point while backing up.
b) Grip the steering wheel at the 12 o'clock position with your left hand: This hand position allows for better control and maneuverability of the steering wheel while backing up.
c) Move the wheel left or right in the direction in which you want the rear of the vehicle to go: This is the fundamental principle of steering while backing up. By turning the wheel in the desired direction, you can guide the rear of the vehicle in that direction.
Therefore, These practices can assist in improving control, visibility, and maneuverability while backing up, ensuring a safer and more effective backing maneuver. The correct option is option d.
To know more about the principle of steering:
https://brainly.com/question/29458022
#SPJ6
define the term 'one solar mass.'
Answer:
the mass of one sun
Explanation:
its really heavy
If an oxygen molecule traveling at the rms speed bounces back and forth between opposite sides of a cubical vessel of 0.10 m on a side, what is the average force the molecule exerts on one of the walls of the container? Assume the molecule’s velocity is perpendicular to the walls it hits.
Answer:
1.25x10^-19N
Explanation:see attached file pls
When the current in a toroidal solenoid is changing at a rate of 0.0260 A/s, the magnitude of the induced emf is 12.2 mV. When the current equals 1.40 A, the average flux through each turn of the solenoid is 0.00308 Wb. How many turns does the solenoid have?
Answer:
The solenoid has 213 turns.
Explanation:
The number of the solenoid's turns (N) can be found as follows:
[tex] N = \frac{L*I}{\phi_{B}} [/tex] (1)
Where:
L: is the self-inductance of the solenoid
I: is the current = 1.40 A
[tex]\phi_{B}[/tex]: is the magnetic flux = 0.00308 Wb
The self-inductance of the solenoid (L) is:
[tex] L = \frac{|\epsilon|}{|dI/dt|} [/tex] (2)
Where:
ε: is the induced emf = 12.2x10⁻³ V
dI/dt: is the rate changing of the current = 0.0260 A/s
By entering equation (2) into (1) we can find the number of turns:
[tex] N = \frac{|\epsilon|*I}{\phi_{B}|dI/dt|} = \frac{12.2 \cdot 10^{-3} V*1.40 A}{0.00308 Wb*0.0260 A/s} = 213 [/tex]
Therefore, the solenoid has 213 turns.
I hope it helps you!
Help!
6. Assume a position vs time graph displays a horizontal line, what does this represent?
A. Constant Velocity
B. 0 Acceleration
if it is horizontal line, that means position is same but time is increasing.
velocity=0 . particle is not even moving
The governor of state A earns $53,745 more than the governor of state B. If the total of their salaries is $289,405, find the salaries of each.
Answer:
Sa is the salary of the governor of state A
Sb is the salary of the governor of state A
"The governor of state A earns $53,745 more than the governor of state B. "
This means that:
Sa = Sb + $53,745
"If the total of their salaries is $289,405,"
means that:
Sa + Sb = $289,405
Then we have two equations:
Sa = Sb + $53,745
Sa + Sb = $289,405
Now, we can replace the first equation into the second equation:
(Sb + $53,745) + Sb = $289,405
2*Sb = $289,405 - $53,745 = $235,660
Sb = ($235,660)/2 = $117,830
and:
Sa = Sb + $53,745 = $117,830 + $53,745 = $171,575
Governor of state A earns: $171,575
Governor of state B earns: $117,830
I REALLY NEED HELP WITH PHYSICS!! HELPPP!! I’m giving 50 points :)))
Answer:
59%
Explanation:
Data obtained from the question include the following:
Input temperature = 495 K
Output temperature = 293 K
Efficiency =?
The efficiency of the car engine can be obtained by multiplying the ratio of the output temperature to the input temperature by 100 as shown below:
Efficiency = output /input x 100
Efficiency = 293/495 x 100
Efficiency = 59.1 ≈ 59%
Therefore, the efficiency of the car engine is approximately 59%
What are the signs of the velocity, force, and acceleration (components) afterthe cart is released and is moving qway from the motion sensor? (The positive xdirection is toward the motion sensor, to the right.
Answer:
car is moving away its direction is negative.
the speed must also be negative.
speed this distance decreases the acceleration is negative and if the speed is increasing the acceleration is positive.
Explanation:
In the exercise they indicate that the direction to the motion sensor is positive, as they indicate that the car is moving away its direction is negative.
The speed of the car is
v = (x₂-x₁) / t
As the positions are negative, and the car moves away the speed must also be negative.
The analysis for acceleration must be very careful if the speed this distance decreases the acceleration is negative and if the speed is increasing the acceleration is positive.
Complete all four parts. 15 points. Will give brainliest! Show work!
Answer:
A. 5.08 secs.
B. 10.16 secs.
C. 126.50 m.
D. 373.36 m
Explanation:
Data obtained from the question include the following:
Initial velocity (u) = 65 m/s
Angle of projection θ = 50°
A. Determination of the time taken to reach the peak.
Initial velocity (u) = 65 m/s
Angle of projection θ = 50°
Acceleration due to gravity (g) = 9.8 m/s²
Time (t) =.?
t = u•Sine θ/g
t = (65 × Sine 50) /9.8
t = 5.08 secs.
B. Determination of the total time spent by the ball in air.
Time (t) taken to reach the peak = 5.08 secs.
Total time (T) spent by the ball in air =?
T = 2t
T = 2 × 5.08
T = 10.16 secs
Therefore, the total time spent by the ball in air is 10.16 secs.
C. Determination of the maximum height.
Initial velocity (u) = 65 m/s
Angle of projection θ = 50°
Acceleration due to gravity (g) = 9.8 m/s²
Maximum height (H) =..?
H = u²•Sine² θ / 2g
H = 65² × (Sine 50)² / 2 × 9.8
H = 4225 × (Sine 50)² /19.6
H = 126.50 m
Therefore, the maximum height reached by the ball is 126.50 m.
D. Determination of the horizontal distance travelled by the ball.
Initial velocity (u) = 65 m/s
Angle of projection θ = 50°
Acceleration due to gravity (g) = 9.8 m/s²
Horizontal distance (R) =..?
R = u²•Sine 2θ / g
R = 65² × Sine (2×30) / 9.8
R = (4225 × Sine 60) / 9.8
R = 373.36 m
Therefore, the horizontal distance travelled by the ball is 373.36 m
When we double the distance between a source of light and the
surface on which it falls, the amount of illumination on the surface
decreases to
(what fraction) of the
original illumination.
The amount of lighting on a surface drops to (1/4) of the initial illumination when the distance between a light source and the surface it falls on is doubled.
What is illumination?The amount of light or luminous flux that falls on a surface is known as illumination. It is expressed as lux or lumens per square meter.
The square of the distance has an inverse relationship with the light intensity;
[tex]\rm I = \frac{1}{r^2}[/tex]
Where,
I is the light intensity
r is the distance
Let r is the distance and I is the sound intensity for case 2;
r' = 2r
[tex]\rm I' = \frac{1}{(2r)^2} \\\\ I' = \frac{1}{4r^2} \\\\ I' = \frac{I}{4}[/tex]
When we double the distance between a source of light and the surface on which it falls, the amount of illumination on the surface decreases to(1/2) of the original illumination.
Hence the value of the fraction is 1/4.
To learn more about the illumination refer;
https://brainly.com/question/20160684
#SPJ2
Which may result from an increase in friction?
A: decreased traction
B: increased speed
C: reduced wear and tear
D: generation of heat
Answer:
Its Generation of Heat. or "D"Explanation:
Friction causes generation of heat and causes increased wear and tear.
The friction is a resistive force and is related to heat energy, so an increase in friction results in the generation of heat, so option D is correct.
What is friction?Two solid objects cannot roll or slide over one another due to the force of friction. Although frictional forces can be useful, such as the traction needed to walk without slipping, they can also present a large degree of resistance to motion. Automobile engines need about 20% of their power to overcome frictional forces in moving parts.
The fundamental source of friction between metals appears to be the adhesion forces between the contact zones of the surfaces, which are always microscopically uneven. Friction is produced by shearing, these "welded" seams, and the rubbing action of the rougher, tougher surface against the softer, smoother surface.
The friction is a resistive force trying to oppose the force applied As friction is related to heat when we increase the heat, the friction increases, and vice versa.
To know more about Friction:
https://brainly.com/question/28356847
#SPJ6
plssss answer it i am stuck in between..prove that pascal is a derived unit using the formulae...
Answer:
See below
Explanation:
We know that the unit of pressure is Pascal.
We have,
Pressure = [tex] \frac{force}{area} [/tex]
[tex] = \frac{m \times g}{l \times b} [/tex]
[tex] = \frac{kg \: \times \: {meter \: per \: second \: }^{2} }{ {m}^{2} } [/tex]
[tex] = kg \: {m}^{ - 1} \: {s}^{ - 2} [/tex]
The unit of pressure i.e Pascal is derived unit because it is expressed depending on more than two units i.e kg / [ m × s × s ]
Hope this helps..
best regards!!
CAN YOU HELP ME IN THE FOLLOWING EQUATION THE SPEED IS V = A + BT. DETERMINE THE DIMENSIONS OF A AND B
Answer:
A = [m/s]
B = [m/s²]
Explanation:
Assuming that V has SI units of m/s, then A and BT must also have units of m/s.
A = [m/s]
BT = [m/s]
Since T has SI units of s:
B [s] = [m/s]
B = [m/s²]