Compute the volume percent of graphite, VGr, in a 2.5 wt% C cast iron, assuming that all the carbon exists as the graphite phase. Assume densities of 7.9 and 2.3 g/cm3 for ferrite and graphite, respectively.

Answer:

The liquids are TOLUENE because the equilibrum vapor above it will be flammable ( D )

Explanation:

Liquids stored at : 1 atm , 25⁰c  and they are vented with air

Determining whether the equilibrum vapor above the liquid will be flammable

We can determine this by using Antoine equation to calculate saturation vapor pressure also apply Dalton's law to determine the volume % concentration of air and finally we compare answer to flammable limits to determine which liquid will be flammable

A) For acetone

using the Antoine equation to calculate saturation vapor pressure

[tex]In(P^{out} ) = A - \frac{B}{C + T}[/tex]

values gotten appendix E ( chemical process safety (3rd edition) )

A = 16.6513

B = 2940.46

C = -35.93

T = 298 k      input values into Antoine equation

therefore ; [tex]p^{out}[/tex] = 228.4 mg

calculate volume percentage using Dalton's law

= V% = (saturation vapor pressure / pressure ) *100

         = (228.4 mmHg / 760 mmHg) * 100 = 30.1%

The liquid is not flammable because its UFL = 12.8%

B) For Benzene

using the Antoine equation to calculate saturation vapor pressure

[tex]In(P^{out} ) = A - \frac{B}{C + T}[/tex]

values gotten appendix E ( chemical process safety (3rd edition) )

A= 15.9008

B = 2788.52

C = -52.36

T = 298 k   input values into the above equation

[tex]p^{out}[/tex] = 94.5 mmHg

calculate volume percentage using Dalton's law

V% = (saturation vapor pressure / pressure ) *100

      = (94.5 / 760 ) * 100 = 12.4%

Benzene is not flammable under the given conditions because its UFL =7.1%

C) For cyclohexane

using the Antoine equation to calculate saturation vapor pressure

[tex]In(P^{out} ) = A - \frac{B}{C + T}[/tex]

values gotten appendix E ( chemical process safety (3rd edition) )

A = 15.7527

B = 2766.63

c = -50.50

T = 298 k

solving the above equation using the given values

[tex]p^{out}[/tex] = 96.9 mmHg

calculate volume percentage using Dalton's law

V% = (saturation vapor pressure / pressure ) *100

      = ( 96.9 mmHg /760 mmHg) * 100 = 12.7%

cyclohexane not flammable under the given conditions because its UFL= 8%

D) For Toluene

using the Antoine equation to calculate saturation vapor pressure

[tex]In(P^{out} ) = A - \frac{B}{C + T}[/tex]

values gotten from appendix E ( chemical process safety (3rd edition) )

A = 16.0137

B = 3096.52

C = -53.67

T = 298 k

solving the above equation using the given values

[tex]p^{out}[/tex] = 28.2 mmHg

calculate volume percentage using Dalton's law

V% = (saturation vapor pressure / pressure ) *100

     = (28.2 mmHg / 760 mmHg) * 100 = 3.7%

Toluene is flammable under the given conditions because its UFL= 7.1%

Answer:

a. Tm = 0.3192min.

b. MRR = 396.91mm^{3}/s.

Explanation:

Given the following data;

Drill diameter, D = 12.7mm

Depth, L = 60mm

Cutting speed, V = 25m/min = 25,000m

Feed, F = 0.30mm/rev

To find the cutting time;

Cutting time, Tm =?

[tex]Tm = \frac{L}{Fr}[/tex] .......eqn 1

We would first solve for the feed rate (F);

[tex]Fr = NF[/tex] .......eqn 2

But we need to find the rotational speed (N);

[tex]N= \frac{V}{\pi *D}[/tex]

[tex]N= \frac{25000}{3.142*12.7}[/tex]

[tex]N= \frac{25000}{39.90}[/tex]

N = 626.57rev/min.

Substiting N into eqn 2;

[tex]Fr = NF[/tex]

Fr = 626.57 * 0.30

Fr = 187.97mm/min.

Substiting F into eqn 1;

[tex]Tm = \frac{L}{Fr}[/tex]

[tex]Tm = \frac{60}{187.97}[/tex]

Tm = 0.3192min.

Therefore, the cutting time is 0.3192 minutes.

For the material removal rate (MRR);

[tex]MRR = \frac{\pi *D^{2}Fr}{4}[/tex]

[tex]MRR = \frac{3.142*12.7^{2}*187.97}{4}[/tex]

[tex]MRR = \frac{3.142*161.29*187.97}{4}[/tex]

[tex]MRR = \frac{95258.16}{4}[/tex]

[tex]MRR = 23814.54mm^{3}/min[/tex]

Time in seconds, we divide by 60;

MRR = 23814.54/60 =396.91mm^{3}/s.

Therefore, the material removal rate (MRR) is 396.91mm^{3}/s.

Answer:

A.) 0 > K > 9.6

B.) K = 9.6

C.) w = +/- 2 sqrt (3)

Explanation:

G(s)= K(s+4)/s(s+1.2)(s+2)

For a closed loop stability, we can analyse by using Routh - Horwitz analysis.

To make the pole completely imaginary, K must be equal to 9.6 Because for oscillations. Whereas, one pair of pole must lie at the imaginary axis.

Please find the attached files for the solution

Answer:

A to C = 6.4 km

Explanation:

A to B = 4 km

B to C = 5 km

A to C =  using pythagorean theorem

a² + b² = c²

a = A to B = 4

b = B to C = 5

c = A to C

c² = 4² + 5²

c = 6.4 km (A to C)

According to the scenario, the distance between town C from town A is found to be 6.40 Km.

The background that this question depends on is known as the direction-based question. These types of questions completely depend on the distance of moving bodies like cars, persons, or any other objects as well with respect to the initial position.

According to the question,

The distance between town A to town B = 4 km.

The distance between town B to town C = 5 km.

Now, according to the Pythagoras theorem, the distance between town C to town A is as follows:

[tex]AC^2[/tex] = [tex]AB^2 +BC^2[/tex].

[tex]AC^2[/tex] = [tex]4^2+5^2[/tex]

[tex]AC^2[/tex] = 16 + 25 = 41.

AC = √41 = 6.40 km.

Therefore, the distance between town C from town A is found to be 6.40 Km.

To learn more about Pythagoras' theorem, refer to the link:

https://brainly.com/question/343682

#SPJ5

Answer:

Hello the table which is part of the question is missing and below are the table values

For a 5V belt the available diameters are : 5.5, 5.8, 5.9, 6.2, 6.3, 6.6, 12.5, 13.9, 15.5, 16.1, 18.5, 20.1

Answers:

belt size = 140 in with diameter of 20.1n

actual speed of belt = 288.49 in/s

actual center distance = 49.345 in

Explanation:

Given data :

Electric motor (driver sheave) speed (w1) = 950 rpm

Driven sheave speed (w2) = 250 rpm

pick D1 ( diameter of driver sheave)  = 5.8 in  ( from table )

To select an appropriate belt size we apply the equation for the velocity ratio to get the diameter first

VR = [tex]\frac{w1}{w2}[/tex] = 950 / 250

also since the speed of  belt would be constant then ;

Vb = w1r1 = w2r2 ------- equation 1

r = d/2

substituting the value of r into equation 1

equation 2 becomes : [tex]\frac{w1}{w2} = \frac{d2}{d1}[/tex]    = VR

Appropriate belt size ( d2) can be calculated as

d2 = [tex]\frac{w1d1}{w2}[/tex] = [tex]\frac{950 * 5.8}{250}[/tex] = 22.04

From the given table the appropriate belt size would be : 20.1 because it is the closest to the calculated value

next we have to determine the belt length /size

[tex]L = 2C + \frac{\pi }{2} ( d1+d2) + \frac{(d2-d1)^2}{4C}[/tex]

inputting  all the values into the above equation including the value of C as calculated below

L ≈ 140 in

Calculating the center distance

we use this equation to get the ideal center distance

[tex]d2< C_{ideal} < 3( d1 +d2)[/tex]

22.04 < c < 3 ( 5.8 + 20.1 )

22.04 < c < 77.7

the center distance is between 22.04 and 77.7  but taking an average value

ideal center distance would be ≈ 48 in

To calculate the actual center distance we use

[tex]C = \frac{B+\sqrt{B^2 - 32(d2-d1)^2} }{16}[/tex] -------- equation 3

B = [tex]4L -2\pi (d2 + d1 )[/tex]

inputting all the values into (B)

B = 140(4) - 2[tex]\pi[/tex]( 20.01 + 5.8 )

B ≈ 399.15 in

inputting all the values gotten Back to equation 3 to get the actual center distance

C = 49.345 in ( actual center distance )

Calculating the actual belt speed

w1 = 950 rpm = 99.48 rad/s

belt speed ( Vb) = w1r1 = w1 * [tex]\frac{d1}{2}[/tex]

                           = 99.48 * 5.8 / 2 = 288.49 in/s

Answer:

E = 2940 J

Explanation:

It is given that,

Mass, m = 12 kg

Position at which the object is placed, h = 25 m

We need to find the potential energy of the mass. It is given by the formula as follows :

E = mgh

g is acceleration due to gravity

[tex]E=12\times 9.8\times 25\\\\E=2940\ J[/tex]

So, the potential energy of the mass is 2940 J.

Answer:

Engineering drawing abbreviations and symbols are used to communicate and detail the characteristics of an engineering drawing.

There are many abbreviations common to the vocabulary of people who work with engineering drawings in the manufacture and inspection of parts and assemblies.

Technical standards exist to provide glossaries of abbreviations, acronyms, and symbols that may be found on engineering drawings. Many corporations have such standards, which define some terms and symbols specific to them; on the national and international level, like BS8110 or Eurocode 2 as an example.

Explanation:

Answer:

Assuming steady state condition the temperature distribution is calculated as expressed in the attached solution below

Explanation:

Given data :

thickness : L , inner surface (x) : 0,  uniform flux : q"o

fraction : β  

volumetric heat generation :  q˙(x)=(1−β)q''oα^e−αx

determine the temperature distribution in the quartz

attached below is the detailed solution

Answer:

D) ΔU = -153.43 kJ and ΔH = -146.00 kJ

Explanation:

Given;

heat energy released by the exothermic reaction, ΔH = -146 kJ

number of gas mol, n = 3 mol

temperature of the gas, T = 298 K

Apply first law of thermodynamic

Change in the internal energy of the system, ΔU;

ΔU = ΔH- nRT

where;

R is gas constant = 8.314 J/mol.K

ΔU = -146kJ - (3 x 8.314 x 298)

ΔU = -146kJ - 7433 J

ΔU = -146kJ - 7.433 kJ

ΔU = -153.43 kJ

Therefore, the enthalpy change of the reaction ΔH is -146 kJ and change in the internal energy of the system is -153.43 kJ

D) ΔU = -153.43 kJ and ΔH = -146.00 kJ

Explanation:

1. increase This due to increase in the pore volume.

2.increase . This is due to the fact that more liquid phase will be present at the firing.

3. Increase. This increase is because of the fact that clay on cooling forms glass.Thus, gaining more strength as the liquid phase formed fills in pore volume.

4. Increase, Rate of corrosion depends upon the surface area exposed.Since, upon vitrification surface area would increase, therefore corrosion increases.

5. Increase , glass has higher thermal conductivity than the pores it fills.

Answer: the thermal conductivity of the sample is 22.4 W/m . °C

Explanation:

We already know that the thermal conductivity of a material is to be determined by ensuring one-dimensional heat conduction, and by measuring temperatures when steady operating conditions are reached.

ASSUMPTIONS

1. Steady operating conditions exist since the temperature readings do not change with time.

2. Heat losses through lateral surfaces are well insulated, and thus the entire heat generated by the heater is conducted through the samples.

3. The apparatus possess thermal symmetry

ANALYSIS

The electrical power consumed by resistance heater and converted to heat is:

Wₐ = VI = ( 110 V ) ( 0.4 A ) = 44 W

Q = 1/2Wₐ = 1/2 ( 44 A )

Now since only half of the heat generated flows through each samples because of symmetry. Reading the same temperature difference across the same distance in each sample also confirms that the apparatus possess thermal symmetry. The heat transfer area is the area normal to the direction of heat transfer. which is the cross- sectional area of the cylinder in this case; so

A = 1/4πD² = 1/3 × π × ( 0.05 m )² = 0.001963 m²

Now Note that, the temperature drops by 15 degree Celsius within 3 cm in the direction of heat flow, the thermal conductivity of the sample will be

Q = kA ( ΔT/L ) → k = QL / AΔT

k = ( 22 W × 0.03 m ) / (0.001963 m² × 15°C )

k = 22.4 W/m . °C

Answer:

the required stress level  at which fracture will occur for a critical internal crack length of 3.0 mm is 189.66 MPa

Explanation:

From the given information; the objective is to compute the stress level at which fracture will occur for a critical internal crack length of 3.0 mm.

The Critical Stress for a maximum internal crack can be expressed by the formula:

[tex]\sigma_c = \dfrac{K_{lc}}{Y \sqrt{\pi a}}[/tex]

[tex]Y= \dfrac{K_{lc}}{\sigma_c \sqrt{\pi a}}[/tex]

where;

[tex]\sigma_c[/tex] = critical stress required for initiating crack propagation

[tex]K_{lc}[/tex] = plain stress fracture toughness = 26 Mpa

Y = dimensionless parameter

a = length of the internal crack

given that ;

the maximum internal crack length is 8.6 mm

half length of the internal  crack will be 8.6 mm/2 = 4.3mm

half length of the internal  crack a = 4.3 × 10⁻³ m

From :

[tex]Y= \dfrac{K_{lc}}{\sigma_c \sqrt{\pi a}}[/tex]

[tex]Y= \dfrac{26}{112 \times \sqrt{\pi \times 4.3 \times 10 ^{-3}}}[/tex]

[tex]Y= \dfrac{26}{112 \times0.1162275716}[/tex]

[tex]Y= \dfrac{26}{13.01748802}[/tex]

[tex]Y=1.99731315[/tex]

[tex]Y \approx 1.997[/tex]

For this same component and alloy, we are to also compute the stress level at which fracture will occur for a critical internal crack length of 3.0 mm.

when the length of the internal crack a = 3mm

half  length of the internal  crack will be 3.0 mm / 2 = 1.5 mm

half length of the internal  crack a =1.5 × 10⁻³ m

From;

[tex]\sigma_c = \dfrac{K_{lc}}{Y \sqrt{\pi a}}[/tex]

[tex]\sigma_c = \dfrac{26}{1.997 \sqrt{\pi \times 1.5 \times 10^{-3}}}[/tex]

[tex]\sigma_c = \dfrac{26}{0.1370877444}[/tex]

[tex]\sigma_c =189.6595506[/tex]

[tex]\sigma_c =[/tex] 189.66 MPa

Thus; the required stress level  at which fracture will occur for a critical internal crack length of 3.0 mm is 189.66 MPa

Answer:

Explanation:

Known: flow rate and inlet temperature for automobile radiator.

Overall heat transfer coefficient.

Find: Area required to achieve a prescribed outlet temperature.

Assumptions: (1) Negligible heat loss to surroundings and kinetic and

potential energy changes, (2) Constant properties.

Analysis: The required heat transfer rate is

q = (m c)h (T h,i - T h,o) = 0.05 kg/s (4209J / kg.K) 70K = 14,732 W

Using the ε-NTU method,

Cmin = Ch = 210.45 W / K

Cmax = Cc = 755.25W / K

Hence, Cmin/Cmx(Th,i - Th,o) = 210.45W / K(100K) = 21,045W

and

ε=q/qmax = 14,732W / 21,045W = 0.700

NTU≅1.5, hence

A=NTU(cmin / U) = 1.5 x 210.45W / K(200W) / m² .K) = 1.58m²

1. the air outlet is..

Tc,o = Tc,i + q / Cc = 300K + (14,732W / 755.25W / K) = 319.5K

2. using the LMTD approach ΔTlm = 51.2 K,, R=0.279 and P=0.7

hence F≅0.95 and

A = q/FUΔTlm = (14,732W) / [0.95(200W / m².K) 51.2K] = 1.51m²

Answer:

a. 6 seconds

b. 180 feet

Explanation:

Images attached to show working.

a. You have the position of the truck so you integrate twice. Use the formula and plug in the time t = 7 sec. Check out uniform acceleration. The time at which the truck's velocity is zero  is when it stops.

b. Determine the initial speed. Plug in the time calculated in the previous step. From this we can observe that the truck comes to a stop before the end of the ramp.

Hey,

Who plays a role in the financial activities of a company?

O D. Everyone at the company, including managers and employees

Answer:

Everyone at the company, including managers and employees

Explanation:

The red and green lights are sidelights that are positioned on the port side (red) (left as facing the bow) and starboard (green) (right as facing the bow) side of the boat. Various white lights are required depending on the size of the boat, but generally, a white masthead light and stern light are required. See the US Coast Guard site in the link below for more specific information.

Hope this helps

Answer:

Voltage across resistor = 2 v

Explanation:

Given data

pulse height = 2 v

pulse width = 4s

calculate voltage across resistor ( the free hand sketch attached below explains more )

pulse height is also = amplitude of voltage ) = 2v

The voltage across the resistor = 2v  Since  the voltage from the source of the circuit is equal to the amplitude voltage in the circuit ( assuming no loss of voltage )

also the graphical representation of the problem is attached below

Answer: 164.2253 MPa

Explanation:

First we find the half internal crack which is  = length of surface crack /2

so α = 8.6 /2 = 4.3mm ( 4.3×10⁻³m )

Now we find the dimensionless parameter using the critical stress crack propagation equation

∝ = K / Y√πα

stress level ∝ = 112Mpa

fracture toughness K = 26Mpa

dimensionless parameter Y = ?

SO working the formula

Y = K / ∝√πα

Y = 26 / 112 (√π × 4.3× 10⁻³)

Y = 1.9973

We are asked to find stress level for internal crack length of  4m

so half internal crack is  = length of surface crack /2

4/2 = 2mm ( 2 × 10⁻³)

from the previous formula critical stress crack propagation equation

∝ = K / Y√πα

∝ = 26 / 1.9973 √(π × 2 × 10⁻³)

∝ = 164.2253 Mpa

Given:

We have given two statements.

Statement 1: Proper footwear may include both leather and steel-toed shoes.

Statement 2:  Leather-soled shoes provide slip resistance.

Find:

Which statement is true.

Solution:

A slip-resistant outsole is smoother and more slip-resistant than other outsole formulations when exposed to water and oil. A smoother outsole in rubber ensures a slip-resistant shoe can handle a slippery floor more effectively.

Slip resistant shoes have an interlocked tread pattern that does not close the water in, enabling the slip resistant sole to touch the floor to provide better slip resistance.

Leather-soled shoes don't provide slop resistance.

Therefore, both the Technicians are wrong.

From the statements made by both technician A and Technician B, we can say that; both technicians are wrong.

We are given the statements made by both technicians;

Technician A: Proper footwear may include both leather and steel-toed shoes.

Technician B: Leather-soled shoes provide slip resistance.

Now, they are talking about safety shoes to be worn in workshops.

A shoe that is Slip resistant will have rubber soles and tread patterns that can help to have better grip of wet or greasy floors.

This is the type of shoe that should be worn by technicians in the workshop.

Thus, Technician A is wrong because proper footwear does not include leather shoes.

Similarly, technician B is also wrong because leather shoes are not safety shoes.

Read more about slip resistant shoes at; https://brainly.com/question/17411739

Answer:

max shear = R = V = 15 kN

Explanation:

given:

load = 10 kn/m

span = 3m

max shear = R = V = wL / 2

max shear = R = V = (10 * 3) / 2

max shear = R = V = 15 kN

Answer:

1) There are  three (3) PWM generator blocks in LM3S1968 and they are

2)  Two (2) independent  PWM outputs can be generated on an LM3S1968

3) Applications for PWM

4) NVIC in a timer stand for ; Nested Vectored Interrupt Controller

its significance is that it is used to handle  and give priorities to exception and Interrupts

5) The counter/timer derive its time period from  counting the output pulses for one cycle which is the duration over which gate is open

Explanation:

1) There are  three (3) PWM generator blocks in LM3S1968 and they are

2)  Two (2) independent  PWM outputs can be generated on an LM3S1968

3) Applications for PWM

4) NVIC in a timer stand for ; Nested Vectored Interrupt Controller

its significance is that it is used to handle  and give priorities to exception and Interrupts

5) The counter/timer derive its time period from  counting the output pulses for one cycle which is the duration over which gate is open

6) THE WAVEFORM DIAGRAMS IS ATTACHED BELOW

it can be seen  that 50 % rises and goes down at half interval. 75 % goes down at half more of 50% and 25% goes down at half less of 50%

Answer:

[tex]\t(x)_{max} =\dfrac{p\times L}{2\times \pi}[/tex]

Explanation:

Given that

Shear modulus= G

Sectional area = A

Torsional load,

[tex]t(x) = p sin( \frac{2\pi}{ L} x)[/tex]

For the maximum value of internal torque

[tex]\dfrac{dt(x)}{dx}=0[/tex]

Therefore

[tex]\dfrac{dt(x)}{dx} = p cos( \frac{2\pi}{ L} x)\times \dfrac{2\pi}{L}\\ p cos( \frac{2\pi}{ L} x)\times \dfrac{2\pi}{L}=0\\cos( \frac{2\pi}{ L} x)=0\\ \dfrac{2\pi}{ L} x=\dfrac{\pi}{2}\\\\x=\dfrac{L}{4}[/tex]

Thus the maximum internal torque will be at x= 0.25 L

[tex]t(x)_{max} = \int_{0}^{0.25L}p sin( \frac{2\pi}{ L} x)dx\\t(x)_{max} =\left [p\times \dfrac{-cos( \frac{2\pi}{ L} x)}{\frac{2\pi}{ L}} \right ]_0^{0.25L}\\t(x)_{max} =\dfrac{p\times L}{2\times \pi}[/tex]

Answer:

true

Explanation:

true

Answer:

I believe this is true

Explanation:

If your looking at something and you look at something else everything is still in perfect view and clear, in focus.

hope this helps :)

Answer:

hello your question is incomplete here is the complete question

. “ABC construction Inc.” company becomes the lowest in the bed process to get a $21 million construction project for “Northern Inc.”. Now “ABC construction Inc.” planning to make a formal contract agreement with the “Northern Inc.”. What are the main elements of this agreement to consider it as a legal contract?

Answer : elements of the agreement

Explanation:

Offer : an offer is the beginning element for any valid agreement to be started or reached between two or more bodies. ABC construction would have to make an offer first for the agreement to be valid

Acceptance: This is part where by the company "Northern Inc" after receiving the offer from ABC construction Inc would have to consent to the approval of the offer made.

capacity : This the element of the agreement that helps to ensure that both parties have the legal and financial backings to embark on the contract agreement .

certainty : This element ensures that both parties understands the terms and conditions attached to the agreement and this to ensure that there are no bogus conditions

Consideration : This is a very vital element because the both parties have to give something in return while going into a valid agreement

Intention to create legal relation : Legal relations are applied to contract agreements whereby both parties want the contract agreement to b legally enforced and this is important in order to prevent contract breach by any party involved in the agreement

Answer:

From the calculation, we can see that the invention's COP of 2.67 does not exceed the maximum theoretical COP of 14.65. Hence his claim is valid and could be possible.

Explanation:

Heat generated Q = 200 kW

power input W = 75 kW

Temperature of heated region [tex]T_{h}[/tex] = 293 K

Temperature of heat source [tex]T_{c}[/tex] = 273 K

For this engine,

coefficient of performance COP = Q/W  = 200/75 = 2.67

The maximum theoretical COP obtainable for a heat pump is given as

COP = [tex]\frac{T_{h} }{T_{h} - T_{c} }[/tex] =  [tex]\frac{293 }{293 - 273 }[/tex] = 14.65

From the calculation, we can see that the invention's COP of 2.67 does not exceed the maximum theoretical COP of 14.65. Hence his claim is valid and could be possible.

Answer:

a) cross sectional area of the core = 0.0187 m²

b) The secondary voltage on no-load = 413 V

c) The primary currency and power factor on no load is 1.21 A and 0.168 lagging respectively.

Explanation:

See attached solution.

In this exercise we have to calculate the formula that will be able to determine the length of the cantilevered, like this:

[tex]\sigma_{max}C=\frac{M_{max}C}{I}[/tex]

So to determinated the maximum tensile and compreensive stress due to bending we can describe the formula as:

[tex]\sigma_b = \frac{MC}{I}[/tex]

Where,

So making this formula for the max, we have:

[tex]\sigma_c=\frac{MC}{I} \\\sigma_T=-\sigma_c=-\frac{MC}{I}\\\sigma_{max}=M_{max}\\[/tex]

With all this information we can put the formula as:

[tex]\sigma_{max}C=\frac{M_{max}C}{I}[/tex]

See more about stress in the beam at brainly.com/question/23637191

Answer:

(a) The value of the resistance is 3.431 Ω

(b) The value of the inductance is 0.0264 H

Explanation:

Given;

frequency of the source, f = 60 Hz

rms voltage, V-rms = 220 V

real power, Pr = 1500 W

apparent power, Pa = 4600 VA

(a). Determine the value of the resistance

[tex]P_r = I_{rms}^2R[/tex]

where;

R is resistance

[tex]I_{rms} = \frac{Apparent \ Power}{V_{rms}} \\\\I_{rms} = \frac{P_a}{V_{rms}}\\\\I_{rms}= \frac{4600}{220} \\\\I_{rms}= 20.91 \ A[/tex]

Resistance is calculated as;

[tex]R = \frac{P_r}{I_{rms}^2} \\\\R = \frac{1500}{(20.91)^2} \\\\R = 3.431 \ ohms[/tex]

(b). Determine the value of the inductance.

[tex]Q_L = I_{rms}^2 X_L[/tex]

where;

[tex]Q_L[/tex] is reactive power

[tex]X_L[/tex] is inductive reactance

[tex]Apparent \ power = \sqrt{Q_L^2 + P_r^2} \\\\P_a^2 = Q_L^2 + P_r^2\\\\Q_L^2 = P_a^2 - P_r^2\\\\Q_L^2 = 4600^2 - 1500^2\\\\Q_L^2 = 18910000\\\\Q_L = \sqrt{18910000}\\\\Q_L = 4348.56 \ VA[/tex]

inductive reactance is calculated as;

[tex]X_L = \frac{Q_L}{I_{rms}^2} \\\\X_L = \frac{4348.56}{(20.91)^2} \\\\X_L = 9.95 \ ohms[/tex]

inductance is calculated as;

[tex]X_L = \omega L\\\\X_L = 2\pi f L\\\\L = \frac{X_L}{2\pi f} \\\\L = \frac{9.95}{2\pi *60} \\\\L = 0.0264 \ H\\\\L = 26.4 \ mH[/tex]